AT24C04AN-10SU-1.8 ATMEL

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 21

Technical content

Features

  • Write Protect Pin for Hardware Data Protection – Utilizes Different Array Protection Compared to the AT24C02/04/08/16  Low-voltage and Standard-voltage Operation – 2.7 (VCC = 2.7V to 5.5V) – 1.8 (VCC = 1.8V to 5.5V)  Internally Organized 256 x 8 (2K), 512 x 8 (4K), 1024 x 8 (8K) or 2048 x 8 (16K)  2-wire Serial Interface  Schmitt Trigger, Filtered Inputs for Noise Suppression  Bi-directional Data Transfer Protocol  100 kHz (1.8V) and 400 kHz (2.5V, 2.7V , 5V) Clock Rate  8-byte Page (2K), 16-byte Page (4K, 8K, 16K) Write Modes  Partial Page Writes are Allowed  Self-timed Write Cycle (5 ms Max)  High Reliability – Endurance: One Million Write Cycles – Data Retention: 100 Years  Automotive Grade, Extended Temperature and Lead-Free/Halogen-Free Devices Available  8-lead PDIP , 8-lead JEDEC SOIC, 8-lead MAP and 8-lead TSSOP Packages

Description

The A T24C02A/04A/08A/16A provides 2048/4096/8192/16384 bits of serial electri- cally erasable and programmable read only memory (EEPROM) organized as 256/512/1024/2048 words of 8 bits each. The device is optimized for use in many industrial and commercial applications where low power and low voltage operation are essential. The AT24C02A/04A/08A/16A is available in space saving 8-lead PDIP , 8-lead JEDEC SOIC, 8-lead MAP and 8-lead TSSOP packages and is accessed via a 2-wire serial interface. In addition, the entire family is available in 2.7V (2.7V to 5.5V) and 1.8V (1.8V to 5.5V) versions. 2-wire Serial EEPROM 2K (256 x 8) 4K (512 x 8) 8K (1024 x 8) 16K (2048 x 8) AT24C02A AT24C04A AT24C08A AT24C16A Rev. 0976L–SEEPR–1/04 Pin Configurations Pin Name Function A0 - A2 Address Inputs SDA Serial Data SCL Serial Clock Input WP Write Protect NC No-connect 8-lead PDIP GND VCC WP SCL SDA 8-lead SOIC GND VCC WP SCL SDA 8-lead TSSOP GND VCC WP SCL SDA 8-lead MAP Bottom View VCC WP SCL SDA GND

2 AT24C02A/04A/08A/16A

0976L–SEEPR–1/04 Block Diagram Pin Description SERIAL CLOCK (SCL): The SCL input is used to positive edge clock data into each EEPROM device and negative edge clock data out of each device. SERIAL DATA (SDA): The SDA pin is bidirectional for serial data transfer. This pin is open-drain driven and may be wire-ORed with any number of other open-drain or open collector devices. DEVICE/PAGE ADDRESSES (A2, A1, A0): The A2, A1 and A0 pins are device address inputs that must be hard wired for the AT24C02A. As many as eight 2K devices may be addressed on a single bus system (device addressing is discussed in detail under the Device Addressing section). The AT24C04A uses the A2 and A1 inputs for hard wire addressing and a total of four 4K devices may be addressed on a single bus system. The A0 pin is a no-connect. Absolute Maximum Ratings* Maximum Ratings” may cause permanent dam- age to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Voltage on Any Pin

0976L–SEEPR–1/04 The AT24C08A only uses the A2 input for hardwire addressing and a total of two 8K devices may be addressed on a single bus system. The A0 and A1 pins are no- connects. The AT24C16A does not use the device address pins, which limits the number of devices on a single bus to one. The A0, A1 and A2 pins are no-connects. WRITE PROTECT (WP): The AT24C02A/04A/08A/16A have a Write Protect pin that provides hardware data protection. The Write Protect pin allows normal read/write oper- ations when connected to ground (GND). When the Write Protect pin is connected to V CC , the write protection feature is enabled and operates as shown in the following table. Memory Organization AT24C02A, 2K SERIAL EEPROM: Internally organized with 32 pages of 8 bytes each, the 2K requires an 8-bit data word address for random word addressing. AT24C04A, 4K SERIAL EEPROM: The 4K is internally organized with 32 pages of 16 bytes each. Random word addressing requires a 9-bit data word address. AT24C08A, 8K SERIAL EEPROM: The 8K is internally organized with 64 pages of 16 bytes each. Random word addressing requires a 10-bit data word address. AT24C16A, 16K SERIAL EEPROM: The 16K is internally organized with 128 pages of 16 bytes each. Random word addressing requires an 11-bit data word address. Note: 1. This parameter is characterized and is not 100% tested. WP Pin Status Part of the Array Protected 24C02A 24C04A 24C08A 24C16A At VCC Upper Half (1K) Array Upper Half (2K) Array Full (8K) Array Full (16K) Array At GND Normal Read/Write Operations Pin Capacitance Applicable over recommended operating range from TA = 25°C, f = 1.0 MHz, VCC = +1.8V. Symbol Test Condition Max Units Conditions C I/O Input/Output Capacitance (SDA) 8 pF V I/O = 0V C IN Input Capacitance (A0, A1, A2, SCL) 6 pF V IN = 0V

4 AT24C02A/04A/08A/16A

0976L–SEEPR–1/04 Note: 1. V IL min and VIH max are reference only and are not tested. DC Characteristics Applicable over recommended operating range from: TAI = -40°C to +85°C, VCC = +1.8V to +5.5V, TAE = -40°C to +125°C, VCC = +1.8V to +5.5V (unless otherwise noted). Symbol Parameter Test Condition Min Typ Max Units VCC1 Supply Voltage 1.8 5.5 V VCC2 Supply Voltage 2.5 5.5 V VCC3 Supply Voltage 2.7 5.5 V VCC4 Supply Voltage 4.5 5.5 V ICC Supply Current VCC = 5.0V READ at 100 kHz 0.4 1.0 mA ICC Supply Current VCC = 5.0V WRITE at 100 kHz 2.0 3.0 mA ISB1 Standby Current VCC = 1.8V V IN = VCC or VSS 0.6 3.0 µA ISB2 Standby Current VCC = 2.5V V IN = VCC or VSS 1.4 4.0 µA ISB3 Standby Current VCC = 2.7V V IN = VCC or VSS 1.6 4.0 µA ISB4 Standby Current VCC = 5.0V V IN = VCC or VSS 8.0 18.0 µA ILI Input Leakage Current V IN = VCC or VSS 0.10 3.0 µA ILO Output Leakage Current V OUT = VCC or VSS 0.05 3.0 µA VIL Input Low Level (1) -0.6 V CC x 0.3 V VIH Input High Level (1) VCC x 0.7 V CC + 0.5 V VOL2 Output Low Level VCC = 3.0V I OL = 2.1 mA 0.4 V VOL1 Output Low Level VCC = 1.8V I OL = 0.15 mA 0.2 V

0976L–SEEPR–1/04 Notes: 1. The AT24C02A/04A/08A bearing the process letter “D” on the package (the mark is located in the lower right corner on the topside of the package), guarantees 400 kHz (2.5V , 2.7V). 2. This parameter is characterized and is not 100% tested (TA = 25°C). 3. This parameter is characterized and is not 100% tested. AC Characteristics Applicable over recommended operating range from TAI = -40°C to +85°C, TAE = -40°C to +125°C, VCC = +1.8V to +5.5V, CL = 1 TTL Gate and 100 pF (unless otherwise noted). Symbol Parameter AT24C02A/ 04A/08A/16A 1.8V AT2402A/04A/ 08A 2.5V, 2.7V AT24C16A 2.5V , 2.7V AT24C02A/ 04A/08A/16A 5.0V UnitsMin Max Min Max Min Max Min Max fSCL Clock Frequency, SCL 100 400 (1) 400 400 kHz tLOW Clock Pulse Width Low 4.7 4.7 1.3 1.2 µs tHIGH Clock Pulse Width High 4.0 4.0 0.6 0.6 µs tI Noise Suppression Time(2) 100 100 100 50 ns tBUF Time the bus must be free before a new transmission can start(3) 4.7 4.7 1.3 1.2 µs tHD.DAT Data In Hold Time 0 0 0 0 µs tSU.DA T Data In Set-up Time 200 200 100 100 ns tR Inputs Rise Time(3) 1.0 1.0 0.3 0.3 µs tF Inputs Fall Time(3) 300 300 300 300 ns tDH Data Out Hold Time 100 100 100 50 ns tWR Write Cycle Time 5 5 5 5 ms Endurance(3) 5.0V, 25°C, Page Mode 1M 1M 1M 1M Write Cycles

6 AT24C02A/04A/08A/16A

0976L–SEEPR–1/04 Device Operation CLOCK and DATA TRANSITIONS: The SDA pin is normally pulled high with an exter- nal device. Data on the SDA pin may change only during SCL low time periods (refer to Data Validity timing diagram). Data changes during SCL high periods will indicate a start or stop condition as defined below. START CONDITION: A high-to-low transition of SDA with SCL high is a start condition which must precede any other command (refer to Start and Stop Definition timing diagram). STOP CONDITION: A low-to-high transition of SDA with SCL high is a stop condition. After a read sequence, the stop command will place the EEPROM in a standby power mode (refer to Start and Stop Definition timing diagram). ACKNOWLEDGE: All addresses and data words are serially transmitted to and from the EEPROM in 8 bit words . The EEPROM sends a zero to acknowledge that it has received each word. This happens during the ninth clock cycle. STANDBY MODE: The AT24C02A/04A/08A/16A features a low power standby mode which is enabled: (a) upon power-up and (b) after the receipt of the STOP bit and the completion of any internal operations. MEMORY RESET: After an interruption in protocol, power loss or system reset, any 2-wire part can be reset by following these steps: (a) Clock up to 9 cycles, (b) look for SDA high in each cycle while SCL is high and then (c) create a start condition as SDA is high.

0976L–SEEPR–1/04 Bus Timing (SCL: Serial Clock, SDA: Serial Data I/O) Write Cycle Timing (SCL: Serial Clock, SDA: Serial Data I/O) Note: 1. The write cycle time tWR is the time from a valid stop condition of a write sequence to the end of the interval clear/write cycle. twr (1) STOP CONDITION START CONDITION WORDn ACK8th BIT SCL SDA

8 AT24C02A/04A/08A/16A

0976L–SEEPR–1/04 Data Validity Start and Stop Definition Output Acknowledge

0976L–SEEPR–1/04 Device Addressing The 2K, 4K and 8K EEPROM devices all require an 8 bit device address word following a start condition to enable the chip for a read or write operation (refer to Figure 1). The device address word consists of a mandatory one, zero sequence for the first four most significant bits as shown. This is common to all the EEPROM devices. The next 3 bits are the A2, A1 and A0 device address bits for the 2K EEPROM. These 3 bits must compare to their corresponding hard-wired input pins. The 4K EEPROM only uses the A2 and A1 device address bits with the third bit being a memory page address bit. The two device address bits must compare to their corre- sponding hard-wired input pins. The A0 pin is no-connect. The 8K EEPROM only uses the A2 device address bit with the next 2 bits being for memory page addressing. The A2 bit must compare to its corresponding hard-wired input pin. The A1 and A0 pins are no-connect. The 16K EEPROM does not use the device address pins, which limits the number of devices on a single bus to one. The A0, A1 and A2 pins are no-connects. The eighth bit of the device address is the read/write operation select bit. A read opera- tion is initiated if this bit is high and a write operation is initiated if this bit is low. Upon a compare of the device address, the EEPROM will output a zero. If a compare is not made, the chip will return to a standby state. Write Operations BYTE WRITE: A write operation requires an 8 bit data word address following the device address word and acknowledgement. Upon receipt of this address, the EEPROM will again respond with a zero and then clock in the first 8 bit data word. Following receipt of the 8 bit data word, the EEPROM will output a zero and the addressing device, such as a microcontroller, must terminate the write sequence with a stop condi- tion. At this time the EEPROM enters an internally-timed write cycle, tWR , to the nonvolatile memory. All inputs are disabled during this write cycle and the EEPROM will not respond until the write is complete (refer to Figure 2). PAGE WRITE: The 2K EEPROM is capable of an 8-byte page write, and the 4K, 8K and 16K devices are capable of 16-byte page writes. A page write is initiated the same as a byte write, but the microcontroller does not send a stop condition after the first data word is clocked in. Instead, after the EEPROM acknowledges receipt of the first data word, the microcontroller can transmit up to seven (2K) or fifteen (4K, 8K, 16K) more data words. The EEPROM will respond with a zero after each data word received. The microcontroller must terminate the page write sequence with a stop condition (refer to Figure 3). The data word address lower three (2K) or four (4K, 8K, 16K) bits are internally incre- mented following the receipt of each data word. The higher data word address bits are not incremented, retaining the memory page row location. When the word address, internally generated, reaches the page boundary, the following byte is placed at the beginning of the same page. If more than eight (2K) or sixteen (4K, 8K, 16K) data words are transmitted to the EEPROM, the data word address will “roll over” and previous data will be overwritten. ACKNOWLEDGE POLLING: Once the internally-timed write cycle has started and the EEPROM i nputs are disabled, acknowledge polling can be initiated. This involves send- ing a start condition followed by the device address word. The read/write bit is representative of the operation desired. Only if the internal write cycle has completed will the EEPROM respond with a zero allowing the read or write sequence to continue.

10 AT24C02A/04A/08A/16A

operations: current address read, random address read and sequential read. rent page to the first byte of the same page. acknowledged by the EEPROM, the current address data word is serially clocked out. stop condition (refer to Figure 4). with a zero but does generate a following stop condition (refer to Figure 5). Figure 1. Device Address

1 A2 A0A1 R/W

2 P0P 1 R/W

12 AT24C02A/04A/08A/16A

Figure 5. Random Read Figure 6. Sequential Read

0976L–SEEPR–1/04 Note: For 2.7V devices used in the 4.5V to 5.5V range, please refer to performance values in the AC and DC characteristics table. Ordering Code Package Operation Range A T24C02A-10PI-2.7 A T24C02AN-10SI-2.7 A T24C02A-10TI-2.7 A T24C02AY1-10YI-2.7 8P3 8S1 8A2 8Y1 Industrial (-40°C to 85°C) A T24C02A-10PI-1.8 A T24C02AN-10SI-1.8 A T24C02A-10TI-1.8 A T24C02AY1-10YI-1.8 8P3 8S1 8A2 8Y1 Industrial (-40°C to 85°C) A T24C02AN-10SU-2.7 A T24C02AN-10SU-1.8 8S1 8S1 Lead-Free/Halogen-Free/ Industrial T emperature (-40°C to 85°C) A T24C02AN-10SE-2.7 8S1 High Grade/Extended Temperature (-40°C to 125°C) Package Type 8P3 8-pin, 0.300" Wide, Plastic Dual Inline Package (PDIP) 8S1 8-lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 8A2 8-lead, 0.170" Wide, Thin Shrink Small Outline Package (TSSOP) 8Y1 8-lead, 4.90 mm x 3.00 mm Body, Dual Footprint, Non-leaded, Miniature Array Package (MAP) Options -2.7 Low Voltage (2.7V to 5.5V) -1.8 Low Voltage (1.8V to 5.5V)

14 AT24C02A/04A/08A/16A

0976L–SEEPR–1/04 Note: For 2.7V devices used in the 4.5V to 5.5V range, please refer to performance values in the AC and DC characteristics table. Ordering Code Package Operation Range A T24C04A-10PI-2.7 A T24C04AN-10SI-2.7 A T24C04A-10TI-2.7 A T24C04AY1-10YI-2.7 8P3 8S1 8A2 8Y1 Industrial (-40°C to 85°C) A T24C04A-10PI-1.8 A T24C04AN-10SI-1.8 A T24C04A-10TI-1.8 A T24C04AY1-10YI-1.8 8P3 8S1 8A2 8Y1 Industrial (-40°C to 85°C) A T24C04AN-10SU-2.7 A T24C04AN-10SU-1.8 8S1 8S1 Lead-Free/Halogen-Free/ Industrial T emperature (-40°C to 85°C) A T24C04AN-10SE-2.7 8S1 High Grade/Extended Temperature (-40°C to 125°C) Package Type 8P3 8-pin, 0.300" Wide, Plastic Dual Inline Package (PDIP) 8S1 8-lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 8A2 8-lead, 0.170" Wide, Thin Shrink Small Outline Package (TSSOP) 8Y1 8-lead, 4.90 mm x 3.00 mm Body, Dual Footprint, Non-leaded, Miniature Array Package (MAP) Options -2.7 Low Voltage (2.7V to 5.5V) -1.8 Low Voltage (1.8V to 5.5V)

0976L–SEEPR–1/04 Note: For 2.7V devices used in the 4.5V to 5.5V range, please refer to performance values in the AC and DC characteristics table. Ordering Code Package Operation Range A T24C08A-10PI-2.7 A T24C08AN-10SI-2.7 A T24C08A-10TI-2.7 A T24C08AY1-10YI-2.7 8P3 8S1 8A2 8Y1 Industrial (-40°C to 85°C) A T24C08A-10PI-1.8 A T24C08AN-10SI-1.8 A T24C08A-10TI-1.8 A T24C08AY1-10YI-1.8 8P3 8S1 8A2 8Y1 Industrial (-40°C to 85°C) A T24C08AN-10SU-2.7 A T24C08AN-10SU-1.8 A T24C08A-10TU-2.7 A T24C08A-10TU-1.8 8S1 8S1 8A2 8A2 Lead-Free/Halogen-Free/ Industrial T emperature (-40°C to 85°C) A T24C08AN-10SE-2.7 8S1 High Grade/Extended Temperature (-40°C to 125°C) Package Type 8P3 8-pin, 0.300" Wide, Plastic Dual Inline Package (PDIP) 8S1 8-lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 8A2 8-lead, 0.170" Wide, Thin Shrink Small Outline Package (TSSOP) 8Y1 8-lead, 4.90 mm x 3.00 mm Body, Dual Footprint, Non-leaded, Miniature Array Package (MAP) Options -2.7 Low Voltage (2.7V to 5.5V) -1.8 Low Voltage (1.8V to 5.5V)

16 AT24C02A/04A/08A/16A

0976L–SEEPR–1/04 Note: For 2.7V devices used in the 4.5V to 5.5V range, please refer to performance values in the AC and DC characteristics table. Ordering Code Package Operation Range A T24C16A-10PI-2.7 A T24C16AN-10SI-2.7 A T24C16A-10TI-2.7 A T24C16AY1-10YI-2.7 8P3 8S1 8A2 8Y1 Industrial (-40°C to 85°C) A T24C16A-10PI-1.8 A T24C16AN-10SI-1.8 A T24C16A-10TI-1.8 A T24C16AY1-10YI-1.8 8P3 8S1 8A2 8Y1 Industrial (-40°C to 85°C) A T24C16AN-10SU-2.7 A T24C16AN-10SU-1.8 A T24C16A-10TU-2.7 A T24C16A-10TU-1.8 8S1 8S1 8A2 8A2 Lead-Free/Halogen-Free/ Industrial T emperature (-40°C to 85°C) A T24C16AN-10SE-2.7 8S1 High Grade/Extended Temperature (-40°C to 125°C) Package Type 8P3 8-pin, 0.300" Wide, Plastic Dual Inline Package (PDIP) 8S1 8-lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 8A2 8-lead, 0.170" Wide, Thin Shrink Small Outline Package (TSSOP) 8Y1 8-lead, 4.90 mm x 3.00 mm Body, Dual Footprint, Non-leaded, Miniature Array Package (MAP) Options -2.7 Low Voltage (2.7V to 5.5V) -1.8 Low Voltage (1.8V to 5.5V)

0976L–SEEPR–1/04 Packaging Information 8P3 – PDIP

2325 Orchard Parkway

San Jose, CA 95131 TITLE DRAWING NO. R REV. 8P3, 8-lead, 0.300" Wide Body, Plastic Dual In-line Package (PDIP) 01/09/02 8P3 B D E e Lb2 b A2 A N eA c

4 PLCS

(Unit of Measure = inches) SYMBOL MIN NOM MAX NOTE Notes: 1. This drawing is for general information only; refer to JEDEC Drawing MS-001, Variation BA for additional information. 2. Dimensions A and L are measured with the package seated in JEDEC seating plane Gauge GS-3. 3. D, D1 and E1 dimensions do not include mold Flash or protrusions. Mold Flash or protrusions shall not exceed 0.010 inch. 4. E and eA measured with the leads constrained to be perpendicular to datum. 5. Pointed or rounded lead tips are preferred to ease insertion. A 0.210 2 A2 0.115 0.130 0.195 b 0.014 0.018 0.022 5 b2 0.045 0.060 0.070 6 b3 0.030 0.039 0.045 6 c 0.008 0.010 0.014 D 0.355 0.365 0.400 3 D1 0.005 3 E 0.300 0.310 0.325 4 E1 0.240 0.250 0.280 3 e 0.100 BSC eA 0.300 BSC 4 L 0.115 0.130 0.150 2

18 AT24C02A/04A/08A/16A

0976L–SEEPR–1/04 8S1 – JEDEC SOIC 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TITLE DRAWING NO. R REV. Note: 10/7/03 8S1, 8-lead (0.150" Wide Body), Plastic Gull Wing Small Outline (JEDEC SOIC) 8S1 B COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A1 0.10 – 0.25 These drawings are for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. A 1.35 – 1.75 b 0.31 – 0.51 C 0.17 – 0.25 D 4.80 – 5.00 E1 3.81 – 3.99 E 5.79 – 6.20 e 1.27 BSC L 0.40 – 1.27 ∅ 0˚ – 8˚ Top View End View Side View e B D A N E C L

0976L–SEEPR–1/04 8A2 – TSSOP San Jose, CA 95131 TITLE DRAWING NO. R REV. 5/30/02 COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE D 2.90 3.00 3.10 2, 5 E 6.40 BSC E1 4.30 4.40 4.50 3, 5 A – – 1.20 A2 0.80 1.00 1.05 b 0.19 – 0.30 4 e 0.65 BSC L 0.45 0.60 0.75 L1 1.00 REF 8A2, 8-lead, 4.4 mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-153, Variation AA, for proper dimensions, tolerances, datums, etc. 2. Dimension D does not include mold Flash, protrusions or gate burrs. Mold Flash, protrusions and gate burrs shall not exceed 0.15 mm (0.006 in) per side. 3. Dimension E1 does not include inter-lead Flash or protrusions. Inter-lead Flash and protrusions shall not exceed 0.25 mm (0.010 in) per side. 4. Dimension b does not include Dambar protrusion. Allowable Dambar protrusion shall be 0.08 mm total in excess of the b dimension at maximum material condition. Dambar cannot be located on the lower radius of the foot. Minimum space between protrusion and adjacent lead is 0.07 mm. 5. Dimension D and E1 to be determined at Datum Plane H. 8A2 B Side View End ViewTop View A L D 123 N b Pin 1 indicator this corner E e

20 AT24C02A/04A/08A/16A

0976L–SEEPR–1/04 8Y1 – MAP A – – 0.90 A1 0.00 – 0.05 D 4.70 4.90 5.10 E 2.80 3.00 3.20 D1 0.85 1.00 1.15 E1 0.85 1.00 1.15 b 0.25 0.30 0.35 e 0.65 TYP L 0.50 0.60 0.70 PIN 1 INDEX AREA D E A A1 b 8 7 6 e L PIN 1 INDEX AREA 1 2 34 A Top View End View Bottom View Side View San Jose, CA 95131 TITLE DRAWING NO. R REV. 8Y1, 8-lead (4.90 x 3.00 mm Body) MSOP Array Package (MAP) Y1 C8Y1 2/28/03 COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE

Printed on recycled paper. 0976L–SEEPR–1/04 xM Disclaimer: Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company’s standard warranty which is detailed in Atmel’s T erms and Conditions located on the Company’s web site. The Company assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not authorized for use as critical components in life support devices or systems. Atmel Corporation Atmel Operations San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Regional Headquarters Europe Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland Tel: (41) 26-426-5555 Fax: (41) 26-426-5500 Asia Room 1219 Chinachem Golden Plaza

77 Mody Road Tsimshatsui

Tel: (852) 2721-9778 Fax: (852) 2722-1369 Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Memory San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 Microcontrollers San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 La Chantrerie BP 70602

44306 Nantes Cedex 3, France

13106 Rousset Cedex, France

1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland Tel: (44) 1355-803-000 Fax: (44) 1355-242-743 RF/Automotive Theresienstrasse 2 Postfach 3535

74025 Heilbronn, Germany

1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom Avenue de Rochepleine BP 123

38521 Saint-Egreve Cedex, France

www.atmel.com/literature © Atmel Corpor ation 2004. All rights reserved. Atmel® and combinations thereof, are the registered trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be the trademarks of others.