AT24C04A ATMEL
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 20
Technical content
Features
- Write Protect Pin for Hardware Data Protection – Utilizes Different Array Protection Compared to the AT24C02/04/08/16 Medium-voltage and Standard-voltage Operation – 5.0 (V CC = 4.5V to 5.5V) – 2.7 (V CC = 2.7V to 5.5V) Internally Organized 256 x 8 (2K), 512 x 8 (4K), 1024 x 8 (8K) or 2048 x 8 (16K) Two-wire Serial Interface Schmitt Trigger, Filtered Inputs for Noise Suppression Bidirectional Data Transfer Protocol 400 kHz (2.7V, 5V) Clock Rate 8-byte Page (2K), 16-byte Page (4K, 8K, 16K) Write Modes Partial Page Writes Allowed Self-timed Write Cycle (5 ms Max) High Reliability – Endurance: One Million Write Cycles – Data Retention: 100 Years Automotive Grade, Extended Temperature, and Lead-Free/Halogen-Free Devices Available 8-lead PDIP , 8-lead JEDEC SOIC, and 8-lead TSSOP Packages
Description
The A T24C02A/04A/08A/16A provides 2048/4096/8192/16384 bits of serial electri- cally erasable and programmable read-only memory (EEPROM) organized as 256/512/1024/2048 words of 8 bits each. The device is optimized for use in many automotive applications where low-power and low-voltage operation are essential. The A T24C02A/04A/08A/16A is available in space-saving 8-lead PDIP , 8-lead JEDEC SOIC, and 8-lead TSSOP packages and is accessed via a two-wire serial interface. In addition, the entire family is available in 2.7V (2.7V to 5.5V) version. Two-wire Serial EEPROM Extended Temperature 2K (256 x 8) 4K (512 x 8) 8K (1024 x 8) 16K (2048 x 8) AT24C02A AT24C04A AT24C08A AT24C16A 5083A–SEEPR–9/04 Table 1. Pin Configurations
2 AT24C02A/04A/08A/16A
Figure 1. Block Diagram EEPROM device and n egative edge clock data out of each device. 4K devices may be addressed on a single bus system. The A0 pin is a no-connect.
devices on a single bus to one. The A0, A1, and A2 pins are no-connects. Table 1. Write Protect bytes each. Random word addressing requires an 8-bit data word address. bytes each. Random word addressing requires a 9-bit data word address. bytes each. Random word addressing requires a 10-bit data word address. 16 bytes each. Random word addressing requires an 11-bit data word address. Note: This parameter is characterized and is not 100% tested. Table 2. Pin Capacitance
4 AT24C02A/04A/08A/16A
Note: 1. V IL min and VIH max are reference only and are not tested. Table 3. DC Characteristics
Note: 1. This parameter is characterized and is not 100% tested (T A = 25°C).
- This parameter is characterized and is not 100% tested.
Table 4. AC Characteristics 100 pF (unless otherwise noted).
6 AT24C02A/04A/08A/16A
Figure 2. Data Validity that must precede any other command (see Figure 3). Figure 3. Start and Stop Definition STOP CONDITION: A low-to-high transition of SDA with SCL high is a stop condition. received each word. This happe ns during the ninth clock cycle. pletion of any internal operations.
8 AT24C02A/04A/08A/16A
Figure 6. Output Acknowledge
a start condition to enable the chip for a read or write operation, as shown in Figure 7. Figure 7. Device Address most significant bits as shown. This is common to all the EEPROM devices. The next three bits are the A2, A1, and A0 device address bits for the 2K EEPROM. These three bits must compare to their corresponding hardwired input pins. sponding hardwired input pins. The A0 pin is no-connect. input pin. The A1 and A0 pins are no-connect. devices on a single bus to one. The A0, A1, and A2 pins are no-connects. tion is initiated if this bit is high, and a write operation is initiated if this bit is low. not made, the chip will re turn to a standby state. write is complete, as shown in Figure 8.
1 A2 A0A1 R/W
2 P0 R/W
10 AT24C02A/04A/08A/16A
Figure 8. Byte Write and 16K devices are capable of 16-byte page writes. sequence with a stop condition, as shown in Figure 9. Figure 9. Page Write will the EEPROM respond with a “0” allowing the read or write sequence to continue.
12 AT24C02A/04A/08A/16A
Figure 12. Sequential Read
5083A–SEEPR–9/04 Note: For 2.7V devices used in the 4.5V to 5.5V range, please refer to performance values in the AC and DC characteristics table s (Table 3 on page 4 and Table 4 on page 5). Ordering Code Package Operation Range A T24C02A-10PE-2.7 A T24C02AN-10SE-2.7 8P3 8S1 Extended T emperature (−40°C to 125°C) A T24C02A-10PQ-2.7 A T24C02AN-10SQ-2.7 A T24C02A-10TQ-2.7 8P3 8S1 8A2 Lead-free/Halogen-free/ Extended T emperature (−40°C to 125°C) Package Type 8P3 8-pin, 0.300” Wide, Plastic Dual Inline Package (PDIP) 8S1 8-lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 8A2 8-lead, 0.170" Wide, Thin Shrink Small Outline Package (TSSOP) Options −2.7 Low Voltage (2.7V to 5.5V)
14 AT24C02A/04A/08A/16A
5083A–SEEPR–9/04 Note: For 2.7V devices used in the 4.5V to 5.5V range, please refer to performance values in the AC and DC characteristics table s (Table 3 on page 4 and Table 4 on page 5). Ordering Code Package Operation Range A T24C04A-10PE-2.7 A T24C04AN-10SE-2.7 A T24C04A-10TE-2.7 8P3 8S1 8A2 Extended T emperature (−40°C to 125°C) A T24C04A-10PQ-2.7 A T24C04A-10TQ-2.7 A T24C04AN-10SQ-2.7 8P3 8A2 8S1 Lead-free/Halogen-free Extended T emperature (−40°C to 125°C) Package Type 8P3 8-pin, 0.300" Wide, Plastic Dual Inline Package (PDIP) 8S1 8-lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 8A2 8-lead, 0.170" Wide, Thin Shrink Small Outline Package (TSSOP) Options −2.7 Low Voltage (2.7V to 5.5V)
5083A–SEEPR–9/04 Note: For 2.7V devices used in the 4.5V to 5.5V range, please refer to performance values in the AC and DC characteristics table s (Table 3 on page 4 and Table 4 on page 5). Ordering Code Package Operation Range A T24C08A-10PE-2.7 A T24C08AN-10SE-2.7 8P3 8S1 Extended T emperature (−40°C to 125°C) A T24C08A-10PQ-2.7 A T24C08AN-10SQ-2.7 A T24C08AN-10TQ-2.7 8P3 8S1 8A2 Lead-free/Halogen-free/ Extended T emperature (−40°C to 125°C) Package Type 8P3 8-pin, 0.300" Wide, Plastic Dual Inline Package (PDIP) 8S1 8-lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 8A2 8-lead, 0.170" Wide, Thin Shrink Small Outline Package (TSSOP) Options −2.7 Low Voltage (2.7V to 5.5V)
16 AT24C02A/04A/08A/16A
5083A–SEEPR–9/04 Note: For 2.7V devices used in the 4.5V to 5.5V range, please refer to performance values in the AC and DC characteristics table (Table 3 on page 4 and Table 4 on page 5). Ordering Code Package Operation Range A T24C16A-10PE-2.7 A T24C16AN-10SE-2.7 8P3 8S1 Extended T emperature (−40°C to 125°C) A T24C16A-10PQ-2.7 A T24C16AN-10SQ-2.7 A T24C16A-10TQ-2.7 8P3 8S1 8A2 Lead-free/Halogen-free Extended T emperature (−40°C to 125°C) Package Type 8P3 8-pin, 0.300" Wide, Plastic Dual Inline Package (PDIP) 8S1 8-lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 8A2 8-lead, 0.170" Wide, Thin Shrink Small Outline Package (TSSOP) Options −2.7 Low Voltage (2.7V to 5.5V)
5083A–SEEPR–9/04 Packaging Information 8P3 – PDIP
2325 Orchard Parkway
San Jose, CA 95131 TITLE DRAWING NO. R REV. 8P3, 8-lead, 0.300" Wide Body, Plastic Dual In-line Package (PDIP) 01/09/02 8P3 B Notes: 1. Thi s drawing is for general information only; refer to JEDEC Drawing MS-001, Variation BA, for additional information. 2. Dimen sions A and L are measured with the package seated in JEDEC seating plane Gauge GS-3. 3. D, D1 and E1 dimensions do not include mold Flash or protrusions. Mold Flash or protrusions shall not exceed 0.010 inch. 4. E and eA measured with the leads constrained to be perpendicular to datum. 5. Pointed or ro unded lead tips are preferred to ease insertion. COMMON DIMENSIONS (Unit of Measure = inches) SYMBOL MIN NOM MAX NOTE D E e Lb2 b A2 A N eA c
4 PLCS
A – – 0.210 2 A2 0.115 0.1 30 0.195 b 0.014 0.01 8 0.022 5 b2 0.045 0.060 0.070 6 b3 0.0 30 0.0 39 0.045 6 c 0.00 8 0.010 0.014 D 0. 355 0. 365 0.400 3 D1 0.005 – – 3 E 0. 300 0. 310 0. 325 4 E1 0.240 0.250 0.2 80 3 e 0.100 B SC eA 0. 300 BSC 4 L 0.115 0.1 30 0.150 2 Top View Side View End View
18 AT24C02A/04A/08A/16A
5083A–SEEPR–9/04 8S1 – JEDEC SOIC 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TITLE DRAWING NO. R REV. Note: 10/7/03 8S1, 8-lead (0.150" Wide Body), Plastic Gull Wing Small Outline (JEDEC SOIC) 8S1 B COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A1 0.10 – 0.25 These drawings are for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. A 1. 35 – 1.75 b 0. 31 – 0.51 C 0.17 – 0.25 D 4. 80 – 5.00 E1 3.81 – 3.99 E 5.79 – 6.20 e 1.27 B SC L 0.40 – 1.27 ∅ 0° – 8° Top View End View Side View e B D A N E C L
5083A–SEEPR–9/04 8A2 – TSSOP San Jose, CA 95131 TITLE DRAWING NO. R REV. 5/30/02 COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE D 2.90 3.00 3.10 2, 5 E 6.40 B SC E1 4. 30 4.40 4.50 3, 5 A – – 1.20 A2 0. 80 1.00 1.05 b 0.19 – 0. 30 4 e 0.65 B SC L 0.45 0.60 0.75 L1 1.00 REF 8A2, 8-lead, 4.4 mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) Notes: 1. Thi s drawing is for general information only. Refer to JEDEC Drawing MO-153, Variation AA, for proper dimensions, tolerances, d atums, etc. 2. Dimen sion D does not include mold Flash, protrusions or gate burrs. Mold Flash, protrusions and gate burrs shall not exceed 0.15 mm (0.006 in) per side. 3. Dimen sion E1 does not include inter-lead Flash or protrusions. Inter-lead Flash and protrusions shall not exceed 0.25 mm (0.010 in) per side. 4. Dimen sion b does not include Dambar protrusion. Allowable Dambar protrusion shall be 0.08 mm total in excess of the b dimension at maximum material condition. Dambar cannot be located on the lower radius of the foot. Minimum space between protr usion and adjacent lead is 0.07 mm. 5. Dimen sion D and E1 to be determined at Datum Plane H. 8A2 B Side View End ViewTop View A L D 123 N b Pin 1 indicator this corner E e
Printed on recycled paper. 5083A–SEEPR–9/04 Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTOR Y WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICU LAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR I NCIDEN- TAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the rig ht to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained her ein. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. Atmel Corporation Atmel Operations San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Regional Headquarters Europe Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland Tel: (41) 26-426-5555 Fax: (41) 26-426-5500 Asia Room 1219 Chinachem Golden Plaza
77 Mody Road Tsimshatsui
Tel: (852) 2721-9778 Fax: (852) 2722-1369 Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Memory San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 Microcontrollers San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 La Chantrerie BP 70602
44306 Nantes Cedex 3, France
13106 Rousset Cedex, France
1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland Tel: (44) 1355-803-000 Fax: (44) 1355-242-743 RF/Automotive Theresienstrasse 2 Postfach 3535
74025 Heilbronn, Germany
1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom Avenue de Rochepleine BP 123
38521 Saint-Egreve Cedex, France
www.atmel.com/literature © Atmel Corporation 2004 . All rights reserved. Atmel ®, logo and combinations thereof are registered trademarks and Everywhere Y ou Are SM is a trademark of Atmel Corporation or its subsidiaries. Other terms and product names may be the trademarks of others.