AT24C128_03 ATMEL

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 20

Technical content

Features

  • Low-voltage and Standard-voltage Operation – 2.7 (VCC = 2.7V to 5.5V) – 1.8 (VCC = 1.8V to 3.6V)  Internally Organized 16,384 x 8 and 32,768 x 8  2-wire Serial Interface  Schmitt Trigger, Filtered Inputs for Noise Suppression  Bidirectional Data Transfer Protocol  1 MHz (5V), 400 kHz (2.7V, 2.5V) and 100 kHz (1.8V) Compatibility  Write Protect Pin for Hardware and Software Data Protection  64-byte Page Write Mode (Partial Page Writes Allowed)  Self-timed Write Cycle (5 ms Typical)  High Reliability – Endurance: One Million Write Cycles – Data Retention: 40 Years  Automotive Grade, Extended Temperature and Lead-Free Devices Available  8-lead JEDEC PDIP , 8-lead JEDEC and EIAJ SOIC, 8-lead MAP, 8-lead TSSOP and 8-ball dBGA2 TM Packages

Description

The AT24C128/256 provides 131,072/262,144 bits of serial electrically erasable and programmable read only memory (EEPROM) organized as 16,384/32,768 words of 8 bits each. The device’s cascadable feature allows up to 4 devices to share a common 2-wire bus. The device is optimized for use in many industrial and commercial applica- tions where low power and low voltage operation are essential. The devices are available in space-saving 8-lead JEDEC PDIP , 8-lead JEDEC SOIC, 8-lead EIAJ SOIC, 8-lead MAP (24C128), 8-lead TSSOP and 8-ball dBGA2 packages. In addition, 2-wire Serial EEPROMs 128K (16,384 x 8) 256K (32,768 x 8) AT24C128 AT24C256 Rev. 0670K–SEEPR–7/03 Pin Configurations Pin Name Function A0 - A1 Address Inputs SDA Serial Data SCL Serial Clock Input WP Write Protect NC No Connect GND Ground 8-lead PDIP NC GND VCC WP SCL SDA 8-lead SOIC NC GND VCC WP SCL SDA 8-ball dBGA2 Bottom View VCC WP SCL SDA NC GND 8-lead TSSOP NC GND VCC WP SCL SDA 8-lead MAP Bottom View VCC WP SCL SDA NC GND

2 AT24C128/256

0670K–SEEPR–7/03 Block Diagram Absolute Maximum Ratings* Maximum Ratings” may cause permanent dam- age to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Voltage on Any Pin

0670K–SEEPR–7/03 Pin Description SERIAL CLOCK (SCL): The SCL input is used to positive edge clock data into each EEPROM device and negative edge clock data out of each device. SERIAL DATA (SDA): The SDA pin is bidirectional for serial data transfer. This pin is open- drain driven and may be wire-ORed with any number of other open-drain or open collector devices. DEVICE/PAGE ADDRESSES (A1, A0): The A1 and A0 pins are device address inputs that are hardwired or left not connected for hardware compatibility with AT24C32/64. When the pins are hardwired, as many as four 128K/256K devices may be addressed on a single bus system (device addressing is discussed in detail under the Device Addressing section). When the pins are not hardwired, the default A 1 and A0 are zero. WRITE PROTECT (WP): The write protect input, when tied to GND, allows normal write oper- ations. When WP is tied high to VCC , all write operations to the memory are inhibited. If left unconnected, WP is internally pulled down to GND. Switching WP to VCC prior to a write oper- ation creates a software write protect function. Memory Organization AT24C128/256, 128K/256K SERIAL EEPROM: The 128K/256K is internally organized as 256/512 pages of 64-bytes each. Random word addressing requires a 14/15-bit data word address.

4 AT24C128/256

0670K–SEEPR–7/03 Pin Capacitance(1) Note: 1. This parameter is characterized and is not 100% tested. DC Characteristics(1) Note: 1. V IL min and VIH max are reference only and are not tested. Applicable over recommended operating range from TA = 25°C, f = 1.0 MHz, VCC = +1.8V. Symbol Test Condition Max Units Conditions C I/O Input/Output Capacitance (SDA) 8 pF V I/O = 0V C IN Input Capacitance (A0, A1, SCL) 6 pF V IN = 0V Applicable over recommended operating range from: TAI = -40°C to +85°C, VCC = +1.8V to +5.5V (unless otherwise noted). Symbol Parameter Test Condition Min Typ Max Units VCC1 Supply Voltage 1.8 3.6 V VCC2 Supply Voltage 2.5 5.5 V VCC3 Supply Voltage 4.5 5.5 V ICC1 Supply Current V CC = 5.0V READ at 400 kHz 1.0 2.0 mA ICC2 Supply Current V CC = 5.0V WRITE at 400 kHz 2.0 3.0 mA ISB1 Standby Current (1.8V option) VCC = 1.8V VIN = VCC or VSS 0.2 µA VCC = 3.6V 2.0 ISB2 Standby Current (2.5V option) VCC = 2.5V VIN = VCC or VSS 0.5 µA VCC = 5.5V 6.0 ISB3 Standby Current (5.0V option) VCC = 4.5 - 5.5V VIN = VCC or VSS 6.0 µA ILI Input Leakage Current VIN = VCC or VSS 0.10 3.0 µA ILO Output Leakage Current VOUT = VCC or VSS 0.05 3.0 µA VIL Input Low Level(1) -0.6 V CC x 0.3 V VIH Input High Level(1) VCC x 0.7 V CC + 0.5 V VOL2 Output Low Level V CC = 3.0V I OL = 2.1 mA 0.4 V VOL1 Output Low Level V CC = 1.8V I OL = 0.15 mA 0.2 V

0670K–SEEPR–7/03 AC Characteristics Notes: 1. This parameter is characterized and is not 100% tested. 2. AC measurement conditions: R L (connects to VCC ): 1.3 kΩ (2.5V, 5V), 10 kΩ (1.8V) Input pulse voltages: 0.3 VCC to 0.7 VCC Input rise and fall times: ≤50 ns Input and output timing reference voltages: 0.5 VCC 3. The AT24C128/256 bearing the process letter “B” in the package marking (lower right corner on the top side of the package), guarantees 1 million write cycle endurance (1.8 - 3.6V). Applicable over recommended operating range from TAI = -40°C to +85°C, VCC = +1.8V to +5.5V, CL = 100 pF (unless oth- erwise noted). Test conditions are listed in Note 2. Symbol Parameter 1.8-volt 2.5-volt 5.0-volt UnitsMin Max Min Max Min Max fSCL Clock Frequency, SCL 100 400 1000 kHz tLOW Clock Pulse Width Low 4.7 1.3 0.4 µs tHIGH Clock Pulse Width High 4.0 0.6 0.4 µs tBUF Time the bus must be free before a new transmission can start(1) 4.7 1.3 0.5 µs tHD.STA Start Hold Time 4.0 0.6 0.25 µs tSU.ST A Start Set-up Time 4.7 0.6 0.25 µs tHD.DAT Data In Hold Time 0 0 0 µs tSU.DA T Data In Set-up Time 200 100 100 ns tR Inputs Rise Time(1) 1.0 0.3 0.3 µs tF Inputs Fall Time(1) 300 300 100 ns tSU.STO Stop Set-up Time 4.7 0.6 0.25 µs tDH Data Out Hold Time 100 50 50 ns tWR Write Cycle Time 20 10 10 ms Endurance(1) 5.0V , 25°C, Page Mode 1,000,000 (3) Write Cycles

6 AT24C128/256

0670K–SEEPR–7/03 Device Operation CLOCK and DATA TRANSITIONS: The SDA pin is normally pulled high with an external device. Data on the SDA pin may change only during SCL low time periods (refer to Data Validity timing diagram). Data changes during SCL high periods will indicate a start or stop condition as defined below. START CONDITION: A high-to-low transition of SDA with SCL high is a start condition which must precede any other command (refer to Start and Stop Definition timing diagram). STOP CONDITION: A low-to-high transition of SDA with SCL high is a stop condition. After a read sequence, the stop command will place the EEPROM in a standby power mode (refer to Start and Stop Definition timing diagram). ACKNOWLEDGE: All addresses and data words are serially transmitted to and from the EEPROM in 8-bit words. The EEPROM sends a zero during the ninth clock cycle to acknowl- edge that it has received each word. STANDBY MODE: The AT24C128/256 features a low power standby mode which is enabled: a) upon power-up and b) after the receipt of the STOP bit and the completion of any internal operations. MEMORY RESET: After an interruption in protocol, power loss or system reset, any 2-wire part can be reset by following these steps: (a) Clock up to 9 cycles, (b) look for SDA high in each cycle while SCL is high and then (c) create a start condition as SDA is high.

0670K–SEEPR–7/03 Bus Timing (SCL: Serial Clock, SDA: Serial Data I/O) Write Cycle Timing (SCL: Serial Clock, SDA: Serial Data I/O) Note: 1. The write cycle time tWR is the time from a valid stop condition of a write sequence to the end of the internal clear/write cycle. SCL SDA STOP CONDITION START CONDITION ACK tWR (1) 8th BIT WORD n

8 AT24C128/256

0670K–SEEPR–7/03 Data Validity Start and Stop Definition Output Acknowledge

0670K–SEEPR–7/03 Device Addressing The 128K/256K EEPROM requires an 8-bit device address word following a start condition to enable the chip for a read or write operation (refer to Figure 1). The device address word con- sists of a mandatory one, zero sequence for the first five most significant bits as shown. This is common to all 2-wire EEPROM devices. The 128K/256K uses the two device address bits A1, A0 to allow as many as four devices on the same bus. These bits must compare to their corresponding hardwired input pins. The A1 and A0 pins use an internal proprietary circuit that biases them to a logic low condition if the pins are allowed to float. The eighth bit of the device address is the read/write operation select bit. A read operation is initiated if this bit is high and a write operation is initiated if this bit is low. Upon a compare of the device address, the EEPROM will output a zero. If a compare is not made, the device will return to a standby state. DATA SECURITY: The AT24C128/256 has a hardware data protection scheme that allows the user to write protect the whole memory when the WP pin is at V CC . Write Operations BYTE WRITE: A write operation requires two 8-bit data word addresses following the device address word and acknowledgment. Upon receipt of this address, the EEPROM will again respond with a zero and then clock in the first 8-bit data word. Following receipt of the 8-bit data word, the EEPROM will output a zero. The addressing device, such as a microcontroller, then must terminate the write sequence with a stop condition. At this time the EEPROM enters an internally-timed write cycle, t WR , to the nonvolatile memory. All inputs are disabled during this write cycle and the EEPROM will not respond until the write is complete (refer to Figure 2). PAGE WRITE: The 128K/256K EEPROM is capable of 64-byte page writes. A page write is initiated the same way as a byte write, but the microcontroller does not send a stop condition after the first data word is clocked in. Instead, after the EEPROM acknowledges receipt of the first data word, the microcontroller can transmit up to 63 more data words. The EEPROM will respond with a zero after each data word received. The microcontroller must ter- minate the page write sequence with a stop condition (refer to Figure 3). The data word address lower 6 bits are internally incremented following the receipt of each data word. The higher data word address bits are not incremented, retaining the memory page row location. When the word address, internally generated, reaches the page boundary, the following byte is placed at the beginning of the same page. If more than 64 data words are transmitted to the EEPROM, the data word address will “roll over” and previous data will be overwritten. The address “roll over” during write is from the last byte of the current page to the first byte of the same page. ACKNOWLEDGE POLLING: Once the internally-timed write cycle has started and the EEPROM inputs are disabled, acknowledge polling can be initiated. This involves sending a start condition followed by the device address word. The read/write bit is representative of the operation desired. Only if the internal write cycle has completed will the EEPROM respond with a zero, allowing the read or write sequence to continue.

10 AT24C128/256

current address read, random address read and sequential read. acknowledged by the EEPROM, the microcontroller must generate another start condition. lowing stop condition (refer to Figure 5). with a zero but does generate a following stop condition (refer to Figure 6). Figure 1. Device Address Figure 2. Byte Write

12 AT24C128/256

0670K–SEEPR–7/03 Note: For 2.7V devices used in the 4.5V to 5.5V range, please refer to performance values in the AC and DC characteristics tables. Ordering Code Package Operation Range A T24C128-10PI-2.7 A T24C128N-10SI-2.7 A T24C128W-10SI-2.7 A T24C128U2-10UI-2.7 A T24C128Y1-10YI-2.7 A T24C128-10TI-2.7 8P3 8S1 8S2 8U2-1 8Y1 8A2 Industrial (-40°C to 85°C) A T24C128-10PI-1.8 A T24C128N-10SI-1.8 A T24C128W-10SI-1.8 A T24C128U2-10UI-1.8 A T24C128Y1-10YI-1.8 A T24C128-10TI-1.8 8P3 8S1 8S2 8U2-1 8Y1 8A2 Industrial (-40°C to 85°C) A T24C128N-10SJ-2.7 A T24C128N-10SJ-1.8 8S1 8S1 Lead-Free/Industrial Temperature (-40°C to 85°C) Package Type 8P3 8-lead, 0.300" Wide, Plastic Dual Inline Package (PDIP) 8S1 8-lead, 0.150" Wide, Plastic Gull Wing Small Outline Package (JEDEC SOIC) 8S2 8-lead, 0.200" Wide, Plastic Gull Wing Small Outline Package (EIAJ SOIC) 8U2-1 8-ball, die Ball Grid Array Package (dBGA2) 8Y1 8-lead, 4.90 mm x 3.00 mm Body, Dual Footprint, Non-leaded, Miniature Array Package (MAP) 8A2 8-lead, 0.170" Wide, Thin Shrink Small Outline Package (TSSOP) Options -2.7 Low-voltage (2.7V to 5.5V) -1.8 Low-voltage (1.8V to 3.6V)

0670K–SEEPR–7/03 Note: For 2.7V devices used in the 4.5V to 5.5V range, please refer to performance values in the AC and DC characteristics tables. Ordering Code Package Operation Range A T24C256-10PI-2.7 A T24C256N-10SI-2.7 A T24C256W-10SI-2.7 A T24C256U2-10UI-2.7 A T24C256-10TI-2.7 8P3 8S1 8S2 8U2-1 8A2 Industrial (-40°C to 85°C) A T24C256-10PI-1.8 A T24C256N-10SI-1.8 A T24C256W-10SI-1.8 A T24C256U2-10UI-1.8 A T24C256-10TI-1.8 8P3 8S1 8S2 8U2-1 8A2 Industrial (-40°C to 85°C) A T24C256N-10SJ-2.7 A T24C256N-10SJ-1.8 8S1 8S1 Lead-Free/Industrial Temperature (-40°C to 85°C) Package Type 8P3 8-lead, 0.300" Wide, Plastic Dual Inline Package (PDIP) 8S1 8-lead, 0.150" Wide, Plastic Gull Wing Small Outline Package (JEDEC SOIC) 8S2 8-lead, 0.200" Wide, Plastic Gull Wing Small Outline Package (EIAJ SOIC) 8U2-1 8-ball, die Ball Grid Array Package (dBGA2) 8A2 8-lead, 0.170" Wide, Thin Shrink Small Outline Package (TSSOP) Options -2.7 Low-voltage (2.7V to 5.5V) -1.8 Low-voltage (1.8V to 3.6V)

14 AT24C128/256

0670K–SEEPR–7/03 Packaging Information 8P3 – PDIP

2325 Orchard Parkway

San Jose, CA 95131 TITLE DRAWING NO. R REV. 8P3, 8-lead, 0.300" Wide Body, Plastic Dual In-line Package (PDIP) 01/09/02 8P3 B D E e Lb2 b A2 A N eA c

4 PLCS

(Unit of Measure = inches) SYMBOL MIN NOM MAX NOTE Notes: 1. This drawing is for general information only; refer to JEDEC Drawing MS-001, Variation BA for additional information. 2. Dimensions A and L are measured with the package seated in JEDEC seating plane Gauge GS-3. 3. D, D1 and E1 dimensions do not include mold Flash or protrusions. Mold Flash or protrusions shall not exceed 0.010 inch. 4. E and eA measured with the leads constrained to be perpendicular to datum. 5. Pointed or rounded lead tips are preferred to ease insertion. A 0.210 2 A2 0.115 0.130 0.195 b 0.014 0.018 0.022 5 b2 0.045 0.060 0.070 6 b3 0.030 0.039 0.045 6 c 0.008 0.010 0.014 D 0.355 0.365 0.400 3 D1 0.005 3 E 0.300 0.310 0.325 4 E1 0.240 0.250 0.280 3 e 0.100 BSC eA 0.300 BSC 4 L 0.115 0.130 0.150 2

0670K–SEEPR–7/03 8S1 – JEDEC SOIC San Jose, CA 95131 TITLE DRAWING NO. R REV. Note: 10/10/01 8S1, 8-lead (0.150" Wide Body), Plastic Gull Wing Small Outline (JEDEC SOIC) 8S1 A H N Top View C E End View A B L e D Side View COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE This drawing is for general information only. Refer to JEDEC Drawing MS-012 for proper dimensions, tolerances, datums, etc. A – – 1.75 B – – 0.51 C – – 0.25 D – – 5.00 E – – 4.00 e 1.27 BSC H – – 6.20 L – – 1.27

16 AT24C128/256

0670K–SEEPR–7/03 8S2 – EIAJ SOIC San Jose, CA 95131 TITLE DRAWING NO. R REV. 8S2, 8-lead, 0.209" Body, Plastic Small Outline Package (EIAJ) 5/2/02 8S2 B Top View Side View End View H N C E A b L e D COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE Notes: 1. This drawing is for general information only; refer to EIAJ Drawing EDR-7320 for additional information. 2. Mismatch of the upper and lower dies and resin burrs aren't included. 3. It is recommended that upper and lower cavities be equal. If they are different, the larger dimension shall be regarded. 4. Determines the true geometric position. A 1.78 2.03 A1 0.05 0.33 b 0.35 0.51 5 C 0.18 0.25 5 D 5.13 5.38 E 5.13 5.41 2, 3 H 7.62 8.38 L 0.51 0.89 e 1.27 BSC 4

0670K–SEEPR–7/03 8U2-1 – dBGA2 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TITLE DRAWING NO. R REV. PO8U2-1 A 6/24/03 COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE 8U2-1, 8-ball, 2.35 x 3.73 mm Body, 0.75 mm pitch, Small Die Ball Grid Array Package (dBGA2) A 0.81 0.91 1.00 A1 0.15 0.20 0.25 A2 0.40 0.45 0.50 b 0.25 0.30 0.35 D 2.35 BSC E 3.73 BSC e 0.75 BSC e1 0.74 REF d 0.75 BSC d1 0.80 REF 1. Dimension 'b' is measured at the maximum solder ball diameter. This drawing is for general information only. d A Side View Top View Bottom View

8 Solder Balls

A B C D (e1) e A1 BALL PAD CORNER (d1) 1. b DA1 BALL PAD CORNER E

18 AT24C128/256

0670K–SEEPR–7/03 8Y1 – MAP A – – 0.90 A1 0.00 – 0.05 D 4.70 4.90 5.10 E 2.80 3.00 3.20 D1 0.85 1.00 1.15 E1 0.85 1.00 1.15 b 0.25 0.30 0.35 e 0.65 TYP L 0.50 0.60 0.70 PIN 1 INDEX AREA D E A A1 b 8 7 6 e L PIN 1 INDEX AREA 1 2 34 A Top View End View Bottom View Side View San Jose, CA 95131 TITLE DRAWING NO. R REV. 8Y1, 8-lead (4.90 x 3.00 mm Body) MSOP Array Package (MAP) Y1 C8Y1 2/28/03 COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE

0670K–SEEPR–7/03 8A2 – TSSOP San Jose, CA 95131 TITLE DRAWING NO. R REV. 5/30/02 COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE D 2.90 3.00 3.10 2, 5 E 6.40 BSC E1 4.30 4.40 4.50 3, 5 A – – 1.20 A2 0.80 1.00 1.05 b 0.19 – 0.30 4 e 0.65 BSC L 0.45 0.60 0.75 L1 1.00 REF 8A2, 8-lead, 4.4 mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-153, Variation AA, for proper dimensions, tolerances, datums, etc. 2. Dimension D does not include mold Flash, protrusions or gate burrs. Mold Flash, protrusions and gate burrs shall not exceed 0.15 mm (0.006 in) per side. 3. Dimension E1 does not include inter-lead Flash or protrusions. Inter-lead Flash and protrusions shall not exceed 0.25 mm (0.010 in) per side. 4. Dimension b does not include Dambar protrusion. Allowable Dambar protrusion shall be 0.08 mm total in excess of the b dimension at maximum material condition. Dambar cannot be located on the lower radius of the foot. Minimum space between protrusion and adjacent lead is 0.07 mm. 5. Dimension D and E1 to be determined at Datum Plane H. 8A2 B Side View End ViewTop View A L D 123 N b Pin 1 indicator this corner E e

Printed on recycled paper. 0670K–SEEPR–7/03 xM Disclaimer: Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company’s standard warranty which is detailed in Atmel’s T erms and Conditions located on the Company’s web site. The Company assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not authorized for use as critical components in life support devices or systems. Atmel Corporation Atmel Operations San Jose, CA 95131 Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Regional Headquarters Europe Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland Tel: (41) 26-426-5555 Fax: (41) 26-426-5500 Asia Room 1219 Chinachem Golden Plaza

77 Mody Road Tsimshatsui

Tel: (852) 2721-9778 Fax: (852) 2722-1369 Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Memory San Jose, CA 95131 Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 Microcontrollers San Jose, CA 95131 Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 La Chantrerie BP 70602

44306 Nantes Cedex 3, France

13106 Rousset Cedex, France

1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland Tel: (44) 1355-803-000 Fax: (44) 1355-242-743 RF/Automotive Theresienstrasse 2 Postfach 3535

74025 Heilbronn, Germany

1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom Avenue de Rochepleine BP 123

38521 Saint-Egreve Cedex, France

literature@atmel.com Web Site http://www.atmel.com © Atmel Corporation 2003. All rights reserved. Atmel® and combinations thereof, are the registered trade- marks, and dBGA2™ is the trademark of Atmel Corporation or its subsidiaries. Other terms and product names may be the trademarks of others.