AT24C128B_08 ATMEL

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 23

Technical content

  1. Features
  • Low-voltage and Standard-voltage Operation – 1.8 (V CC = 1.8V to 5.5V)  Internally Organized as 16,384 x 8  Two-wire Serial Interface  Schmitt Trigger, Filtered Inputs for Noise Suppression  Bidirectional Data Transfer Protocol  1 MHz (5.5V, 2.5V), and 400 kHz (1.8V) Compatibility  Write Protect Pin for Hardware and Software Data Protection  64-byte Page Write Mode (Partial Page Writes Allowed)  Self-timed Write Cycle (5 ms Max)  High Reliability – Endurance: One Million Write Cycles – Data Retention: 40 Years  Lead-free/Halogen-free  8-lead JEDEC PDIP, 8-lead JEDEC SOIC, 8-lead Ultra Thin Mini MAP, 8-lead Ultra Lead Frame Land Grid Array (ULA), 8-lead TSSOP, and 8-ball dBGA2 Packages  Die Sales: Wafer Form, Tape and Reel and Bumped Wafers 2. Description The AT24C128B provides 131,072 bits of serial electrically erasable and programma- ble read-only memory (EEPROM ) organized as 16,384 wo rds of 8 bits each. The device’s cascadable feature allows up to eight devices to share a common two-wire bus. The device is optimized for use in many industrial and commercial applications where low-power and low-voltage operation are essential. The devices are available in space-saving 8-lead JEDEC PDIP, 8-lead JEDEC SOIC, 8-lead Ultra Thin Mini MAP, 8-lead Ultra Lead Frame Land Grid Array (ULA), 8-lead TSSOP, and 8-ball dBGA2 packages. In addition, the entire family is available in a 1.8V (5.5V to 3.6V) version. Two-wire Serial EEPROM 128K (16,384 x 8) AT24C128B Rev. 5296A–SEEPR–1/08 Table 0-1. Pin Configurations Pin Name Function A0–A2 Address Inputs SDA Serial Data SCL Serial Clock Input WP Write Protect GND Ground GND VCC WP SCL SDA VCC WP SCL SDA GND VCC WP SCL SDA GND 8-lead PDIP 8-lead SOIC 8-lead dBGA2 GND VCC WP SCL SDA 8-lead TSSOP Bottom View VCC WP SCL SDA GND 8-lead Ultra Thin Mini MAP Bottom View VCC WP SCL SDA GND 8-lead Ultra Lead Frame Land Grid Array Bottom View

5296A–SEEPR–1/08 AT24C128B Figure 3-1. Block Diagram 3. Absolute Maximum Ratings* Maximum Ratings” may cause permanent dam- age to the device. This is a stress rating only; functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Voltage on Any Pin START STOP LOGIC VCC GND WP SCL SDA SERIAL CONTROL LOGIC EN H.V. PUMP/TIMING EEPROM DATA RECOVERY SERIAL MUX X DEC DOUT/ACK LOGIC COMP LOAD INC DATA WORD ADDR/COUNTER Y DEC R/W DOUT DIN LOAD DEVICE ADDRESS COMPARATOR

5296A–SEEPR–1/08 AT24C128B 4. Pin Description SERIAL CLOCK (SCL): The SCL input is used to positive-edge clock data into each EEPROM device and negative-edge clock data out of each device. SERIAL DATA (SDA): The SDA pin is bidirectional for seri al data transfer. This pin is open- drain driven and may be wire-ORed with any number of other open-drain or open-collector devices. DEVICE/PAGE ADDRESSES (A2, A1, A0): The A2, A1, and A0 pins are device address inputs that are hardwired (directly to GND or to Vcc) for compatibility with other AT24Cxx devices. When the pins are hardwired, as many as eight 128K devices may be addressed on a single bus system. (Device addressing is discussed in detail under “Device Addressing,” page 8.) A device is selected when a corresponding hardware and software match is true. If these pins are left floating, the A2, A1, and A0 pins will be interna lly pulled down to GND. However, due to capaci- tive coupling that may appear during customer applications, Atmel recommends always connecting the address pins to a known state. When using a pull-up resistor, Atmel recommends using 10kΩ or less. WRITE PROTECT (WP): The write protect input, when connected to GND, allows normal write operations. When WP is connected directly to Vcc, all write operations to the memory are inhib- ited. If the pin is left floating, the WP pin will be internal ly pulled down to GND. However, due to capacitive coupling that may appear during cu stomer applications, Atmel recommends always connecting the WP pins to a known state. When using a pull-up resistor, Atmel recommends using 10kΩ or less.

5296A–SEEPR–1/08 AT24C128B 5. Memory Organization AT24C128B, 128K SERIAL EEPROM: The 128K is internally organized as 256 pages of 64 bytes each. Random word addressing requires a 14-bit data word address. Table 5-1. Pin Capacitance(1) Note: 1. This parameter is characterized and is not 100% tested. Table 5-2. DC Characteristics Notes: 1. V IL min and VIH max are reference only and are not tested. Applicable over recommended operating range from TA = 25°C, f = 1.0 MHz, VCC = +1.8V to 5.5V Symbol Test Condition Max Units Conditions CI/O Input/Output Capacitance (SDA) 8 pF V I/O = 0V CIN Input Capacitance (A0, A1, SCL) 6 pF V IN = 0V Applicable over recommended operating range from: TAI = − 40°C to +85°C, VCC = +1.8V to +5.5V (unless otherwise noted) Symbol Parameter Test Co ndition Min Typ Max Units VCC1 Supply Voltage 1.8 5.5 V ICC1 Supply Current V CC = 5.0V READ at 400 kHz 1.0 2.0 mA ICC2 Supply Current V CC = 5.0V WRITE at 400 kHz 2.0 3.0 mA ISB1 Standby Current (1.8V option) VCC = 1.8V VIN = VCC or VSS 1.0 µA VCC = 5.5V 6.0 µA ILI Input Leakage Current VCC = 5.0V VIN = VCC or VSS 0.10 3.0 µA ILO Output Leakage Current VCC = 5.0V VOUT = VCC or VSS 0.05 3.0 µA VIL Input Low Level(1) − 0.6 VCC x 0.3 V VIH Input High Level(1) VCC x 0.7 V CC + 0.5 V VOL2 Output Low Level V CC = 3.0V I OL = 2.1 mA 0.4 V VOL1 Output Low Level V CC = 1.8V I OL = 0.15 mA 0.2 V

5296A–SEEPR–1/08 AT24C128B Table 5-3. AC Characteristics (Industrial Temperature) Notes: 1. This parameter is ensured by characterization and is not 100% tested. 2. AC measurement conditions: RL (connects to VCC): 1.3 kΩ (2.5V, 5.5V), 10 kΩ (1.8V) Input pulse voltages: 0.3 VCC to 0.7 VCC Input rise and fall times: ≤ 50 ns Input and output timing reference voltages: 0.5 VCC Applicable over recommended operating range from TAI = − 40°C to +85°C, VCC = +1.8V to +5.5V, CL = 100 pF (unless oth- erwise noted). Test conditions are listed in Note 2. Symbol Parameter 1.8-volt 2.5, 5.5-volt UnitsMin Max Min Max fSCL Clock Frequency, SCL 400 1000 kHz tLOW Clock Pulse Width Low 1.3 0.4 µs tHIGH Clock Pulse Width High 0.6 0.4 µs ti Noise Suppression Time(1) 100 50 ns tAA Clock Low to Data Out Valid 0.05 0.9 0.05 0.55 µs tBUF Time the bus must be free before a new transmission can start(1) 1.3 0.5 µs tHD.STA Start Hold Time 0.6 0.25 µs tSU.STA Start Set-up Time 0.6 0.25 µs tHD.DAT Data In Hold Time 0 0 µs tSU.DAT Data In Set-up Time 100 100 ns tR Inputs Rise Time(1) 0.3 0.3 µs tF Inputs Fall Time(1) 300 100 ns tSU.STO Stop Set-up Time 0.6 0.25 µs tDH Data Out Hold Time 50 50 ns tWR Write Cycle Time 5 5 ms Endurance(1) 25°C, Page Mode, 3.3V 1,000,000 Write Cycles

5296A–SEEPR–1/08 AT24C128B sequential read operation is terminated when the microcontroller does not respond with a “0” but does generate a following stop condition (see Figure 9-3). Figure 9-3. Sequential Read

5296A–SEEPR–1/08 AT24C128B Notes: 1. “-B” denotes bulk. 3. Available in tape and reel and wafer form; order as SL788 for inkless wafer form. Bumped die available upon request. Please contact Serial Interface Marketing. 10. AT24C128B Ordering Information Ordering Code Voltage Package Operation Range AT24C128B-PU (Bulk Form Only) 1.8 8P3 Lead-free/Halogen-free Industrial Temperature (−40°C to 85°C) AT24C128BN-SH-B(1) (NiPdAu Lead Finish) 1.8 8S1 AT24C128BN-SH-T(2) (NiPdAu Lead Finish) 1.8 8S1 AT24C128B-TH-B(1) (NiPdAu Lead Finish) 1.8 8A2 AT24C128B-TH-T(2) (NiPdAu Lead Finish) 1.8 8A2 AT24C128BY6-YH-T(2) (NiPdAu Lead Finish) 1.8 8Y6 AT24C128BD3-DH-T(2) (NiPdAu Lead Finish) 1.8 8D3 AT24C128BU2-UU-T(2) 1.8 8U2-1 AT24C128B-W-11(3) 1.8 Die Sale Industrial Temperature (−40°C to 85°C) Package Type 8P3 8-lead, 0.300" Wide, Plastic Dual Inline Package (PDIP) 8S1 8-lead, 0.150" Wide, Plastic Gull Wing Small Outline Package (JEDEC SOIC) 8A2 8-lead, 0.170" Wide, Thin Shrink Small Outline Package (TSSOP) 8Y6 8-lead, 2.00 mm x 3.00 mm Body, 0.50 mm Pitch, Ultra Thin Mini MAP , Dual No Lead Package, (DFN), (MLP2x3mm) 8D3 8-lead, 1.80 mm x 2.20 mm Body, Ultra Lead Frame Land Grid Array (ULA) 8U2-1 8-ball, die Ball Grid Array Package (dBGA2) Options −1.8 Low-voltage (1.8V to 5.5V)

5296A–SEEPR–1/08 AT24C128B 11. Part marking scheme 11.1 8-PDIP 11.2 8-SOIC TOP MARK Seal Year Y = SEAL YEAR WW = SEAL WEEK | Seal Week 6: 2006 0: 2010 02 = Week 2 | | | 7: 2007 1: 2011 04 = Week 4 A T M L U Y W W 9: 2009 3: 2013 :: : :::: ::

2 D B 1 52 = Week 52

  • Lot Number Lot Number to Use ALL Characters in Marking | BOTTOM MARK Pin 1 Indicator (Dot) No Bottom Mark TOP MARK Seal Year Y = SEAL YEAR WW = SEAL WEEK | Seal Week 6: 2006 0: 2010 02 = Week 2 | | | 7: 2007 1: 2011 04 = Week 4 A T M L H Y W W 9: 2009 3: 2013 :: : :::: ::
  • Lot Number Lot Number to Use ALL Characters in Marking | BOTTOM MARK Pin 1 Indicator (Dot) No Bottom Mark

5296A–SEEPR–1/08 AT24C128B 11.3 8-TSSOP 11.4 8-Ultra Thin Mini-MAP TOP MARK Pin 1 Indicator (Dot) Y = SEAL YEAR WW = SEAL WEEK | 6: 2006 0: 2010 02 = Week 2

2 D B 1 * 50 = Week 50

C 0 0 C00 = Country or Origin A A A A A A A AAA = Atmel Lot Number <- Pin 1 Indicator TOP MARK Y = YEAR OF ASSEMBLY |---|---|---|

2 D B XX = ATMEL LOT NUMBER TO COORESPOND WITH

|---|---|---| NSEB TRACE CODE LOG BOOK. |---|---|---| Y X X |---|---|---| Y = SEAL YEAR * 6: 2006 0: 2010 | 7: 2007 1: 2011 Pin 1 Indicator (Dot) 8: 2008 2: 2012 9: 2009 3: 2013

5296A–SEEPR–1/08 AT24C128B 11.5 8-ULA 11.6 dBGA2 TOP MARK Y = YEAR OF ASSEMBLY |---|---|---| XX = ATMEL LOT NUMBER TO COORESPOND WITH 2 D B NSEB TRACE CODE LOG BOOK. Y X X |---|---|---| * Y = BUILD YEAR | 6: 2006 Pin 1 Indicator (Dot) 7: 2007 8: 2008 Etc... TOP MARK |<-- Pin 1 This Corner P = COUNTRY OF ORIGIN Y = ONE DIGIT YEAR CODE 4: 2004 7: 2007 5: 2005 8: 2008 6: 2006 9: 2009 M = SEAL MONTH (USE ALPHA DESIGNATOR A-L) A = JANUARY B = FEBRUARY J = OCTOBER K = NOVEMBER L = DECEMBER TC = TRACE CODE (ATMEL LOT NUMBERS TO CORRESPOND WITH ATK TRACE CODE LOG BOOK)

5296A–SEEPR–1/08 AT24C128B 8P3 – PDIP

2325 Orchard Parkway

San Jose, CA 95131 TITLE DRAWING NO. R REV. 8P3, 8-lead, 0.300" Wide Body, Plastic Dual In-line Package (PDIP) 01/09/02 8P3 B Notes: 1. Thi s drawing is for general information only; refer to JEDEC Drawing MS-001, Variation BA, for additional information. 2. Dimen sions A and L are measured with the package seated in JEDEC seating plane Gauge GS-3. 3. D, D1 and E1 dimensions do not include mold Flash or protrusions. Mold Flash or protrusions shall not exceed 0.010 inch. 4. E and eA measured with the leads constrained to be perpendicular to datum. 5. Pointed or ro unded lead tips are preferred to ease insertion. COMMON DIMENSIONS (Unit of Measure = inches) SYMBOL MIN NOM MAX NOTE D E e Lb2 b A2 A N eA c

4 PLCS

A – – 0.210 2 A2 0.115 0.1 30 0.195 b 0.014 0.01 8 0.022 5 b2 0.045 0.060 0.070 6 b3 0.0 30 0.0 39 0.045 6 c 0.00 8 0.010 0.014 D 0. 355 0. 365 0.400 3 D1 0.005 – – 3 E 0. 300 0. 310 0. 325 4 E1 0.240 0.250 0.2 80 3 e 0.100 B SC eA 0. 300 BSC 4 L 0.115 0.1 30 0.150 2 Top View Side View End View

5296A–SEEPR–1/08 AT24C128B 8S1 - JEDEC SOIC 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TITLE DRAWING NO. R REV. Note: 3/17/05 8S1, 8-lead (0.150" Wide Body), Plastic Gull Wing Small Outline (JEDEC SOIC) 8S1 C COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A1 0.10 – 0.25 These drawings are for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. A 1.35 – 1.75 b 0.31 – 0.51 C 0.17 – 0.25 D 4.80 – 5.05 E1 3.81 – 3.99 E 5.79 – 6.20 e 1.27 BSC L 0.40 – 1.27 θ 0° – 8° ØØ EE NN TOP VIEW CC E1E1 END VIEW AA bb LL A1A1 ee DD SIDE VIEW

5296A–SEEPR–1/08 AT24C128B 8A2 - TSSOP San Jose, CA 95131 TITLE DRAWING NO. R REV. 5/30/02 COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE D 2.90 3.00 3.10 2, 5 E 6.40 BSC E1 4.30 4.40 4.50 3, 5 A – – 1.20 A2 0.80 1.00 1.05 b 0.19 – 0.30 4 e 0.65 BSC L 0.45 0.60 0.75 L1 1.00 REF 8A2, 8-lead, 4.4 mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-153, Variation AA, for proper dimensions, tolerances, datums, etc. 2. Dimension D does not include mold Flash, protrusions or gate burrs. Mold Flash, protrusions and gate burrs shall not exceed 0.15 mm (0.006 in) per side. 3. Dimension E1 does not include inter-lead Flash or protrusions. Inter-lead Flash and protrusions shall not exceed 0.25 mm (0.010 in) per side. 4. Dimension b does not include Dambar protrusion. Allowable Dambar protrusion shall be 0.08 mm total in excess of the b dimension at maximum material condition. Dambar cannot be located on the lower radius of the foot. Minimum space between protrusion and adjacent lead is 0.07 mm. 5. Dimension D and E1 to be determined at Datum Plane H. 8A2 B Side View End ViewTop View A L D 123 N b Pin 1 indicator this corner E e

5296A–SEEPR–1/08 AT24C128B 8Y6 – MAP San Jose, CA 95131 TITLE DRAWING NO. R REV. 8Y6, 8-lead 2.0 x 3.0 mm Body, 0.50 mm Pitch, Utlra Thin Mini-Map, Dual No Lead Package (DFN) ,(MLP 2x3) D8Y6 10/16/07 Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-229, for proper dimensions, tolerances, datums, etc. 2. Dimension b applies to metallized terminal and is measured between 0.15 mm and 0.30 mm from the terminal tip. If the terminal has the optional radius on the other end of the terminal, the dimension should not be measured in that radius area. 3. Soldering the large thermal pad is optional, but not recommended. No electrical connection is accomplished to the device through this pad, so if soldered it should be tied to ground COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE D 2.00 BSC E 3.00 BSC D2 1.40 1.50 1.60 E2 - - 1.40 A - - 0.60 A1 0.0 0.02 0.05 A2 - - 0.55 A3 0.20 REF L 0.20 0.30 0.40 e 0.50 BSC b 0.20 0.25 0.30 2 A2A2 b (8X)(8X) Pin 1 IDPin 1 ID Pin 1Pin 1 IndexIndex AreaArea A1A1 A3A3 D E A L (8X)L (8X) e (6X)e (6X) 1.50 REF.1.50 REF. D2D2 E2E2

5296A–SEEPR–1/08 AT24C128B 8D3 - ULA 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TITLE DRAWING NO. R REV. 8D3, 8-lead (1.80 x 2.20 mm Body) Ultra Leadframe Land Grid Array (ULA) D3 08D3 11/15/05 COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A – – 0.40 A1 0.00 – 0.05 D 1.70 1.80 1.90 E 2.10 2.20 2.30 b 0.15 0.20 0.25 e 0.40 TYP e1 1.20 REF L 0.25 0.30 0.35 0.10 0.15 b 6 57 E D 1 2 PIN #1 ID TOP VIEW L b A e PIN #1 ID SIDE VIEW BOTTOM VIEW

5296A–SEEPR–1/08 AT24C128B 8U2-1 - dBGA2 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TITLE DRAWING NO. R REV. PO8U2-1 A 6/24/03 COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE 8U2-1, 8-ball, 2.35 x 3.73 mm Body, 0.75 mm pitch, Small Die Ball Grid Array Package (dBGA2) A 0. 81 0.91 1.00 A1 0.15 0.20 0.25 A2 0.40 0.45 0.50 b 0.25 0. 30 0. 35 1 D 2. 35 BSC E 3.73 BSC e 0.75 B SC e1 0.74 REF d 0.75 B SC d1 0. 80 REF 1. Dimension 'b' is measured at the maximum solder ball diameter. This drawing is for general information only. d A Side View Top View Bottom View

8 Solder Balls

A B C D (e1) e A1 BALL PAD CORNER (d1) 1. b DA1 BALL PAD CORNER E

5296A–SEEPR–1/08 AT24C128B

Revision History

Doc. Rev. Date Comments 5296A 1/2008 AT24C128B product with date code 2008 work week 14 (814) or later supports 5Vcc operation Initial document release

5296A–SEEPR–1/08 Headquarters International Atmel Corporation San Jose, CA 95131 USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Atmel Asia Room 1219 Chinachem Golden Plaza

77 Mody Road Tsimshatsui

Tel: (852) 2721-9778 Fax: (852) 2722-1369 Atmel Europe Le Krebs 8, Rue Jean-Pierre Timbaud BP 309

78054 Saint-Quentin-en-

9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Product Contact Web Site www.atmel.com Technical Support s_eeprom@atmel.com Sales Contact www.atmel.com/contacts Literature Requests www.atmel.com/literature Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL ’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL ’S WEB SITE, ATMEL ASSUMES NO LI ABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTOR Y WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICU LAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR I NCIDEN- TAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATME L HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or comp leteness of the contents of this document and reserves the rig ht to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained her ein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not int ended, authorized, or warranted for use as components in applications in tended to support or sustain life. ©2008 Atmel Corporation . All rights reserved. Atmel ®, logo and combinations thereof, and ot hers, are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.