AT24C1024B_08 ATMEL

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 25

Technical content

Features

  • Low-voltage Operation –1 . 8 V ( VCC = 1.8V to 3.6V) –2 . 5 V ( VCC = 2.5V to 5.5V)
  • Internally Organized 131,072 x 8
  • Two-wire Serial Interface
  • Schmitt Triggers, Filtered Inputs for Noise Suppression
  • Bidirectional Data Transfer Protocol
  • 400 kHz (1.8V) and 1 MHz (5V, 2.5V) Clock Rate
  • Write Protect Pin for Hardware and Software Data Protection
  • 256-byte Page Write Mode (Partial Page Writes Allowed)
  • Random and Sequential Read Modes
  • Self-timed Write Cycle (5 ms Typical)
  • High Reliability – Endurance: 1,000,000 Write Cycles/Page – Data Retention: 40 Years
  • 8-lead PDIP, 8-lead JEDEC SOIC, 8-lead EIAJ SOIC, 8-lead TSSOP, 8-lead Ultra Thin Small Array (SAP), and 8-ball dBGA2 Packages
  • Die Sales: Wafer Form, Tape and Reel and Bumped Die

Description

The AT24C1024B provides 1,048,576 bits of serial electrically erasable and program- mable read only memory (EEPROM) organized as 131,072 words of 8 bits each. The device’s cascadable feature allows up to four devices to share a common two-wire bus. The device is optimized for use in many industrial and commercial applications where low-power and low-voltage operation are essential. The devices are available in space-saving 8-lead PDIP, 8-lead JEDEC SOIC, 8-lead EIAJ SOIC, 8-lead TSSOP, 8-ball dBGA2 and 8-lead Ultra Thin SAP packages. In addition, the entire family is Two-wire Serial EEPROM 1M (131,072 x 8) AT24C1024B with Two Device Address Inputs Rev. 5194F–SEEPR–1/08 8-lead PDIP NC GND VCC WP SCL SDA 8-lead TSSOP VCC WP SCL SDA NC GND 8-lead SOIC NC GND VCC WP SCL SDA 8-lead Ultra-Thin SAP Bottom View VCC WP SCL SDA NC GND 8-lead dBGA2 Bottom View VCC WP SCL SDA NC GND

5194F–SEEPR–1/08 AT24C1024B Table 0-1. Pin Configurations Pin Name Function A1 Address Input A2 Address Input SDA Serial Data SCL Serial Clock Input WP Write Protect NC No Connect 1. Absolute Maximum Ratings* Maximum Ratings” may cause permanent dam- age to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Voltage on Any Pin

5194F–SEEPR–1/08 AT24C1024B Figure 1-1. Block Diagram 2. Pin Description SERIAL CLOCK (SCL): The SCL input is used to positive edge clock data into each EEPROM device and negative edge clock data out of each device. SERIAL DATA (SDA): The SDA pin is bi-directional for serial data transfer. This pin is open- drain driven and may be wire-ORed with any number of other open-drain or open-collector devices. DEVICE/ADDRESSES (A1/A2): The A1, A2 pin is a device address input that can be hardwired or left not connected for hard ware compatibility with other AT24Cxx devices. When the A1, A2 pins are hardwired, as many as four 1024K devices may be addressed on a single bus system (device addressing is discussed in detail under the Device Addressing section). If the A1/A2 pins are left floating, the A1/A2 pin will be internally pulled down to GND if the capacitive coupling to the circuit board V CC plane is <3 pF. If coupling is >3 pF, Atmel recommends connecting the A1/A2 pin to GND. WRITE PROTECT (WP): The write protect input, when connec ted to GND, allows normal write operations. When WP is connected high to VCC, all write operations to the memory are inhibited. If the pin is left floating, the WP pin will be intern ally pulled down to GND if the capacitive cou- pling to the circuit board VCC plane is <3 pF. If coupling is >3 pF, Atmel recommends connecting the pin to GND. Switching WP to V CC prior to a write operation creat es a software write-protect function. START STOP LOGIC VCC GND WP SCL SDA SERIAL CONTROL LOGIC EN H.V. PUMP/TIMING EEPROM DATA RECOVERY SERIAL MUX X DEC DOUT/ACK LOGIC COMP LOAD INC DATA WORD ADDR/COUNTER Y DEC R/W DOUT DIN LOAD DEVICE ADDRESS COMPARATOR

5194F–SEEPR–1/08 AT24C1024B 3. Memory Organization AT24C1024B, 1024K SERIAL EEPROM: The 1024K is internally organized as 512 pages of 256 bytes each. Random word addressing requires a 17-bit data word address. Note: 1. This parameter is characterized and is not 100% tested. Note: 1. V IL min and VIH max are reference only and are not tested. Table 3-1. Pin Capacitance(1) Applicable over recommended operating range from TA = 25°C, f = 1.0 MHz, VCC = +1.8V Symbol Test Condition Max Units Conditions CI/O Input/Output Capacitance (SDA) 8 pF V I/O = 0V CIN Input Capacitance (A1, SCL) 6 pF V IN = 0V Table 3-2. DC Characteristics Applicable over recommended operating range from: TAI = –40°C to +85°C, VCC = +1.8V to +5.5V (unless otherwise noted) Symbol Parameter Test Co ndition Min Typ Max Units VCC1 Supply Voltage 1.8 3.6 V VCC2 Supply Voltage 2.5 5.5 V ICC Supply Current V CC = 5.0V READ at 400 kHz 2.0 mA ICC Supply Current V CC = 5.0V WRITE at 400 kHz 3.0 mA ISB1 Standby Current VCC = 1.8V VIN = VCC or VSS 1.0 µA VCC = 3.6V 3.0 µA ISB2 Standby Current VCC = 2.5V VIN = VCC or VSS 2.0 µA VCC = 5.5V 6.0 µA ILI Input Leakage Current V IN = VCC or VSS 0.10 3.0 µA ILO Output Leakage Current VOUT = VCC or VSS 0.05 3.0 µA VIL Input Low Level(1) –0.6 V CC x 0.3 V VIH Input High Level(1) VCC x 0.7 V CC + 0.5 V VOL1 Output Low Level V CC = 1.8V I OL = 0.15 mA 0.2 V VOL2 Output Low Level V CC = 3.0V I OL = 2.1 mA 0.4 V Table 3-3. AC Characteristics (Industrial Temperature) Applicable over recommended operating range from TAI = −40°C to +85°C, VCC = +1.8V to +3.6V, CL = 100 pF (unless oth- erwise noted). Test conditions are listed in Note 2. Symbol Parameter 1.8-volt 2.5, 5.0-volt UnitsMin Max Min Max fSCL Clock Frequency, SCL 400 1000 kHz tLOW Clock Pulse Width Low 1.3 0.4 µs tHIGH Clock Pulse Width High 0.6 0.4 µs

5194F–SEEPR–1/08 AT24C1024B Notes: 1. This parameter is ensured by characterization only. 2. AC measurement conditions: RL (connects to VCC): 1.3 kΩ (2.5V, 5V), 10 kΩ (1.8V) Input pulse voltages: 0.3 VCC to 0.7 VCC Input rise and fall times: ≤ 50 ns Input and output timing reference voltages: 0.5 VCC 4. Device Operation CLOCK and DATA TRANSITIONS: The SDA pin is normally pulled high with an external device. Data on the SDA pin may change only during SCL low time periods (see Figure 4-4 on page 7). Data changes during SCL high periods will indicate a start or stop condition as defined below. ti Noise Suppression Time(1) 100 50 ns tAA Clock Low to Data Out Valid 0.05 0.9 0.05 0.55 µs tBUF Time the bus must be free before a new transmission can start(1) 1.3 0.5 µs tHD.STA Start Hold Time 0.6 0.25 µs tSU.STA Start Set-up Time 0.6 0.25 µs tHD.DAT Data In Hold Time 0 0 µs tSU.DAT Data In Set-up Time 100 100 ns tR Inputs Rise Time(1) 0.3 0.3 µs tF Inputs Fall Time(1) 300 100 ns tSU.STO Stop Set-up Time 0.6 0.25 µs tDH Data Out Hold Time 50 50 ns tWR Write Cycle Time 5 5 ms Endurance(1) 25°C, Page Mode, 3.3V 1,000,000 Write Cycles Table 3-3. AC Characteristics (Industrial Temperature) Applicable over recommended operating range from TAI = −40°C to +85°C, VCC = +1.8V to +3.6V, CL = 100 pF (unless oth- erwise noted). Test conditions are listed in Note 2. Symbol Parameter 1.8-volt 2.5, 5.0-volt UnitsMin Max Min Max

5194F–SEEPR–1/08 AT24C1024B DATA SECURITY: The AT24C1024B has a hardware data protection scheme that allows the user to write-protect the entire memory when the WP pin is at VCC. 6. Write Operations BYTE WRITE: To select a data word in the 1024K memory requires a 17-bit word address. The word address field consists of the P 0 bit of the device address, then the most significant word address followed by the least significant word address (see Figure 7-2 on page 11) A write operation requires the P 0 bit and two 8-bit data word addresses following the device address word and acknowledgment. Upon receipt of this address, the EEPROM will again respond with a zero and then clock in the first 8-bit data word. Following receipt of the 8-bit data word, the EEPROM will output a zero. The addres sing device, such as a microcontroller, then must terminate the writ e sequence with a stop condition. At this time the EEPROM enters an internally timed write cycle, T WR, to the nonvolatile memory. All inputs are disabled during this write cycle and the EEPROM will not respond until the write is complete (see Figure 7-2 on page 11). PAGE WRITE: The 1024K EEPROM is capable of 256-byte page writes. A page write is initiated the same way as a byte write, but the microcontroller does not send a stop condition after the first data word is cl ocked in. Instead, after the EEPROM acknowledges receipt of the first data word, the microcontrolle r can transmit up to 255 more data words. The EEPROM will respond with a zero after each data word received. The microcontroller must ter- minate the page write sequence with a stop condition (see Figure 7-3 on page 11). The data word address lower 8 bits are internally incremented following the receipt of each data word. The higher data word address bits are not incremented, retaining the memory page row location. When the word address, internally generated, reaches the page boundary, the follow- ing byte is placed at the beginning of the same page. If more than 256 data words are transmitted to the EEPROM, the data word a ddress will “roll over” and previous data will be overwritten. The address “rollover” during write is from the last byte of the current page to the first byte of the same page. ACKNOWLEDGE POLLING: Once the internally timed wr ite cycle has st arted and the EEPROM inputs are disabled, ackno wledge polling can be initiate d. This involves sending a start condition followed by the device address wo rd. The read/write bit is representative of the operation desired. Only if th e internal write cycle has comp leted will the EEPROM respond with a zero, allowing the read or write sequence to continue. 7. Read Operations Read operations are initiated the same way as write operations with the exception that the read/write select bit in the device address word is set to one. There are three read operations: current address read, random address read and sequential read. CURRENT ADDRESS READ: The internal data word address counter maintains the last address accessed during the last read or write operation, incremented by one. This address stays valid between operations as long as the ch ip power is maintained. The address “rollover” during read is from the last byte of the last memory page, to the first byte of the first page.

5194F–SEEPR–1/08 AT24C1024B Once the device address with the read/write select bit set to one is clocked in and acknowledged by the EEPROM, the current address data word is serially clocked out. The microcontroller does not respond with an input zero but does generate a following stop condition (see Figure 7-4 on page 11). RANDOM READ: A random read requires a “dummy” byte write sequence to load in the data word address. Once the device address word and data word address are clocked in and acknowledged by the EEPROM, the microcontrolle r must generate another start condition. The microcontroller now initiates a current address read by sending a device address with the read/write select bit high. The EEPROM acknowl edges the device address and serially clocks out the data word. The microcontroller does not respond with a zero but does generate a follow- ing stop condition (see Figure 7-5 on page 12). SEQUENTIAL READ: Sequential reads are initiated by either a current address read or a ran- dom address read. After the microcontroller receives a data word, it responds with an acknowledge. As long as the EEPROM receives an acknowledge, it will continue to increment the data word address and serially clock out sequential data words. When the memory address limit is reached, the data word address will “roll over” and the sequential read will continue. The sequential read operation is te rminated when the microcontroller does not respond with a zero, but does generate a following stop condition (see Figure 7-6 on page 12).

5194F–SEEPR–1/08 AT24C1024B Notes: 1. “-B” denotes bulk 3. Available in tape and reel and wafer form; order as SL788 for inkless wafer form. Bumped die available upon request. Please contact Serial Interface Marketing.

Ordering Information

Ordering Code Voltage Package Operation Range AT24C1024B-PU (Bulk form only) 1.8 8P3 Lead-free/Halogen-free/ Industrial Temperature (–40°C to 85°C) AT24C1024B-PU25 (Bulk form only) 2.5 8P3 AT24C1024BN-SH-B(1) (NiPdAu Lead Finish) 1.8 8S1 AT24C1024BN-SH-T(2) (NiPdAu Lead Finish) 1.8 8S1 AT24C1024BN-SH25-B(1) (NiPdAu Lead Finish) 2.5 8S1 AT24C1024BN-SH25-T(2) (NiPdAu Lead Finish) 2.5 8S1 AT24C1024BW-SH-B(1) (NiPdAu Lead Finish) 1.8 8S2 AT24C1024BW-SH-T(2) (NiPdAu Lead Finish) 1.8 8S2 AT24C1024BW-SH25-B(1) (NiPdAu Lead Finish) 2.5 8S2 AT24C1024BW-SH25-T(2) (NiPdAu Lead Finish) 2.5 8S2 AT24C1024B-TH-B(1) (NiPdAu Lead Finish) 1.8 8A2 AT24C1024B-TH-T(2) (NiPdAu Lead Finish) 1.8 8A2 AT24C1024B-TH25-B(1) (NiPdAu Lead Finish) 2.5 8A2 AT24C1024B-TH25-T(2) (NiPdAu Lead Finish) 2.5 8A2 AT24C1024BY7-YH-T(2) (NiPdAu Lead Finish) 1.8 8Y7 AT24C1024BY7-YH25-T(2) (NiPdAu Lead Finish) 2.5 8Y7 AT24C1024BU4-UU-T(2) 1.8 8U4-1 AT24C1024B-W-11(3) 1.8 Die Sale Industrial Temperature (–40°C to 85°C) Package Type 8P3 8-lead, 0.300" Wide, Plastic Dual In-line Package (PDIP) 8S1 8-lead, 0.150” Wide, Plastic Gull Wing Small Outline Package (JEDEC SOIC) 8S2 8-lead, 0.200” Wide Plastic Gull Wing Small Outline Package (EIAJ SOIC) 8A2 8-lead, 4.4 mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) 8Y7 8-lead, 6.00 mm x 4.90 mm Body, Ultra Thin, Dual Footprint, Non-leaded, Small Array Package (SAP) 8U4-1 8-ball, die Ball Grid Array Package (dBGA2) Options –1.8 Low-voltage (1.8V to 3.6V) –2.5 Low-voltage (2.5V to 5.5V)

5194F–SEEPR–1/08 AT24C1024B 8. Part marking scheme 8.1 8-SOIC(1.8V) 8.2 8-SOIC(2.5V) TOP MARK Seal Year Y = SEAL YEAR WW = SEAL WEEK | Seal Week 6: 2006 0: 2010 02 = Week 2 | | | 7: 2007 1: 2011 04 = Week 4 A T M L H Y W W 9: 2009 3: 2013 :: : :::: ::

2 G B 1 52 = Week 52

  • Lot Number Lot Number to Use ALL Characters in Marking | BOTTOM MARK Pin 1 Indicator (Dot) No Bottom Mark TOP MARK Seal Year Y = SEAL YEAR WW = SEAL WEEK | Seal Week 6: 2006 0: 2010 02 = Week 2 | | | 7: 2007 1: 2011 04 = Week 4 A T M L H Y W W 9: 2009 3: 2013 :: : :::: ::

2 G B 2 52 = Week 52

  • Lot Number Lot Number to Use ALL Characters in Marking | BOTTOM MARK Pin 1 Indicator (Dot) No Bottom Mark

5194F–SEEPR–1/08 AT24C1024B 8.3 8-TSSOP(1.8V) 8.4 8-TSSOP(2.5V) TOP MARK Pin 1 Indicator (Dot) Y = SEAL YEAR WW = SEAL WEEK | 6: 2006 0: 2010 02 = Week 2

2 G B 1 50 = Week 50

<- Pin 1 Indicator TOP MARK Pin 1 Indicator (Dot) Y = SEAL YEAR WW = SEAL WEEK | 6: 2006 0: 2010 02 = Week 2

2 G B 2 50 = Week 50

<- Pin 1 Indicator

5194F–SEEPR–1/08 AT24C1024B 8.5 8-PDIP(1.8V) 8.6 8-PDIP(2.5V) 8.7 8-Ultra Thin SAP (1.8V) TOP MARK Seal Year Y = SEAL YEAR WW = SEAL WEEK | Seal Week 6: 2006 0: 2010 02 = Week 2 | | | 7: 2007 1: 2011 04 = Week 4 A T M L U Y W W 9: 2009 3: 2013 :: : :::: ::

  • Lot Number Lot Number to Use ALL Characters in Marking | BOTTOM MARK Pin 1 Indicator (Dot) No Bottom Mark TOP MARK Seal Year Y = SEAL YEAR WW = SEAL WEEK | Seal Week 6: 2006 0: 2010 02 = Week 2 | | | 7: 2007 1: 2011 04 = Week 4 A T M L U Y W W 9: 2009 3: 2013 :: : :::: ::
  • Lot Number Lot Number to Use ALL Characters in Marking | BOTTOM MARK Pin 1 Indicator (Dot) No Bottom Mark TOP MARK Seal Year | Seal Week Y = SEAL YEAR WW = SEAL WEEK | | | 6: 2006 0: 2010 02 = Week 2 A T M L H Y W W 8: 2008 2: 2012 :: : :::: :

Pin 1 Indicator (Dot)

5194F–SEEPR–1/08 AT24C1024B 8.8 8-Ultra Thin SAP (2.5V) 8.9 dBGA2 TOP MARK Seal Year | Seal Week Y = SEAL YEAR WW = SEAL WEEK | | | 6: 2006 0: 2010 02 = Week 2 A T M L H Y W W 8: 2008 2: 2012 :: : :::: : Pin 1 Indicator (Dot) TOP MARK |<-- Pin 1 This Corner P = COUNTRY OF ORIGIN Y = ONE DIGIT YEAR CODE 4: 2004 7: 2007 5: 2005 8: 2008 6: 2006 9: 2009 M = SEAL MONTH (USE ALPHA DESIGNATOR A-L) A = JANUARY B = FEBRUARY J = OCTOBER K = NOVEMBER L = DECEMBER TC = TRACE CODE (ATMEL LOT NUMBERS TO CORRESPOND WITH ATK TRACE CODE LOG BOOK)

5194F–SEEPR–1/08 AT24C1024B 9. Packaging Information 8P3 – PDIP

2325 Orchard Parkway

San Jose, CA 95131 TITLE DRAWING NO. R REV. 8P3, 8-lead, 0.300" Wide Body, Plastic Dual In-line Package (PDIP) 01/09/02 8P3 B Notes: 1. This drawing is for general information only; refer to JEDEC Drawing MS-001, Variation BA, for additional information . 2. Dimensions A and L are measured with the package seated in JEDEC seating plane Gauge GS-3. 3. D, D1 and E1 dimensions do not include mold Flash or protrusions. Mold Flash or protrusions shall not exceed 0.010 inch. 4. E and eA measured with the leads constrained to be perpendicular to datum. 5. Pointed or rounded lead tips are preferred to ease insertion. COMMON DIMENSIONS (Unit of Measure = inches) SYMBOL MIN NOM MAX NOTE D E e Lb2 b A2 A N eA c

4 PLCS

A – – 0.210 2 A2 0.115 0.130 0.195 b 0.014 0.018 0.022 5 b2 0.045 0.060 0.070 6 b3 0.030 0.039 0.045 6 c 0.008 0.010 0.014 D 0.355 0.365 0.400 3 D1 0.005 – – 3 E 0.300 0.310 0.325 4 E1 0.240 0.250 0.280 3 e 0.100 BSC eA 0.300 BSC 4 L 0.115 0.130 0.150 2 Top View Side View End View

5194F–SEEPR–1/08 AT24C1024B 8S1 - JEDEC SOIC 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TITLE DRAWING NO. R REV. Note: 3/17/05 8S1, 8-lead (0.150" Wide Body), Plastic Gull Wing Small Outline (JEDEC SOIC) 8S1 C COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A1 0.10 – 0.25 These drawings are for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. A 1.35 – 1.75 b 0.31 – 0.51 C 0.17 – 0.25 D 4.80 – 5.05 E1 3.81 – 3.99 E 5.79 – 6.20 e 1.27 BSC L 0.40 – 1.27 θ 0° – 8° ØØ EE NN TOP VIEW CC E1E1 END VIEW AA bb LL A1A1 ee DD SIDE VIEW

5194F–SEEPR–1/08 AT24C1024B 8S2 – EIAJ SOIC San Jose, CA 95131 TITLE DRAWING NO. R REV. 8S2, 8-lead, 0.209" Body, Plastic Small Outline Package (EIAJ) 4/7/06 8S2 D COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE Notes: 1. This drawing is for general information only; refer to EIAJ Drawing EDR-7320 for additional information. 2. Mismatch of the upper and lower dies and resin burrs aren't included. 3. It is recommended that upper and lower cavities be equal. If they are different, the larger dimension shall be regarded. 4. Determines the true geometric position. A 1.70 2.16 A1 0.05 0.25 b 0.35 0.48 5 C 0.15 0.35 5 D 5.13 5.35 E1 5.18 5.40 2, 3 E 7.70 8.26 L 0.51 0.85 θ 0° 8° e 1.27 BSC 4 θθ NN EE TOP VIEW CC E1E1 END VIEW AA bb LL A1A1 ee DD SIDE VIEW

5194F–SEEPR–1/08 AT24C1024B 8A2 - TSSOP San Jose, CA 95131 TITLE DRAWING NO. R REV. 5/30/02 COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE D 2.90 3.00 3.10 2, 5 E 6.40 B SC E1 4. 30 4.40 4.50 3, 5 A – – 1.20 A2 0. 80 1.00 1.05 b 0.19 – 0. 304 e 0.65 B SC L 0.45 0.60 0.75 L1 1.00 REF 8A2, 8-lead, 4.4 mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) Notes: 1. Thi s drawing is for general information only. Refer to JEDEC Drawing MO-153, Variation AA, for proper dimensions, tolerances, datums, etc. 2. Dimen sion D does not include mold Flash, protrusions or gate burrs. Mold Flash, protrusions and gate burrs shall not exceed 0.15 mm (0.006 in) per side. 3. Dimen sion E1 does not include inter-lead Flash or protrusions. Inter-lead Flash and protrusions shall not exceed 0.25 mm (0.010 in) per side. 4. Dimen sion b does not include Dambar protrusion. Allowable Dambar protrusion shall be 0.08 mm total in excess of the b dimension at maximum material condition. Dambar cannot be located on the lower radius of the foot. Minimum space between protrusion and adjacent lead is 0.07 mm. 5. Dimen sion D and E1 to be determined at Datum Plane H. 8A2 B Side View End ViewTop View A L D 123 N b Pin 1 indicator this corner E e

5194F–SEEPR–1/08 AT24C1024B 8U4-1 - dBGA2 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TITLE DRAWING NO. R REV. PO8U4-1 A 1/5/05 COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE 8U4-1, 8-ball, 2.47 x 4.07 mm Body, 0.75 mm pitch, Small Die Ball Grid Array Package (dBGA2) A 0.81 0.91 1.00 A1 0.15 0.20 0.25 A2 0.40 0.45 0.50 b 0.25 0.30 0.35 D 2.47 BSC E 4.07 BSC e 0.75 BSC e1 0.74 REF d 0.75 BSC d1 0.80 REF 5. Dimension 'b' is measured at the maximum solder ball diameter. This drawing is for general information only. d A SIDE VIEW TOP VIEW

8 SOLDER BALLS

A B C D (e1) e A1 BALL PAD CORNER (d1) 5. b DA1 BALL PAD CORNER E

5194F–SEEPR–1/08 AT24C1024B 8Y7 – SAP 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TITLE DRAWING NO. R REV. 8Y7, 8-lead (6.00 x 4.90 mm Body) Ultra-Thin SOIC Array Package (UTSAP) Y7 B8Y7 10/13/05 COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A – – 0.60 A1 0.00 – 0.05 D 5.80 6.00 6.20 E 4.70 4.90 5.10 D1 3.30 3.40 3.50 E1 3.90 4.00 4.10 b 0.35 0.40 0.45 e 1.27 TYP e1 3.81 REF L 0.50 0.60 0.70 PIN 1 ID L b e PIN 1 INDEX AREA A E D A

5194F–SEEPR–1/08 AT24C1024B 10. Revision History Doc. No. Date Comments 5194F 1/2008 Removed ‘NiPdAu’ from AT24C1024BU4-UU-T(2) Removed ‘Preliminary’ status 5194E 8/2007 Updated Part Marking Scheme Updated to new Template Updated to common figures Added Package Marking tables 5194D 5/2007 Changed ‘Advance Information’ to ‘Preliminary’ 5194C 4/2007 Reduced Pin Configuration sizes Changed Maximum Operating Voltage from 6.0 to 6.25 Removed Device Power Up & Power Down Recommendation Added A2 bit to Device Addressing Removed LSB from Figure 10 Current Address Read Removed reference to Waffle Pack Modified Ordering Code table lines Global change on Voltage from 3.6 to 5.5, Correct pg 1 drawings to include address inputs 5194B 2/2007 Correct pg 1 TSSOP drawing 5194A 1/2007 Initial Document Release

5194F–SEEPR–1/08 Headquarters International Atmel Corporation San Jose, CA 95131 USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Atmel Asia Room 1219 Chinachem Golden Plaza

77 Mody Road Tsimshatsui

Tel: (852) 2721-9778 Fax: (852) 2722-1369 Atmel Europe Le Krebs 8, Rue Jean-Pierre Timbaud BP 309

78054 Saint-Quentin-en-

9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Product Contact Web Site www.atmel.com Technical Support s_eeprom@atmel.com Sales Contact www.atmel.com/contacts Literature Requests www.atmel.com/literature Disclaimer: The information in this document is provided in connection wi th Atmel products. No license, expr ess or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LI ABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTOR Y WARRANTY RELATING TO ITS PRODUCTS INCLUDING , BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICU LAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRE CT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR I NCIDEN- TAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or comp leteness of the contents of th is document and reserves the rig ht to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained her ein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not int ended, authorized, or warranted for use as components in applications intended to support or sustain life. ©2008 Atmel Corporation . All rights reserved. Atmel ®, logo and combinations thereof, are regist ered trademarks or trademarks of Atmel Cor- poration or its subsidiaries. Other terms and product names may be trademarks of others.