AT24C04B_09 ATMEL

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 28

Technical content

Features

  • Low-voltage and Standard-voltage Operation ─ 1.8 (VCC = 1.8V to 5.5V)
  • Internally Organized 512 x 8 (4K), or 1024 x 8 (8K)
  • Two-wire Serial Interface
  • Schmitt Trigger, Filtered Inputs for Noise Suppression
  • Bidirectional Data Transfer Protocol
  • 1 MHz (5V), 400 kHz (1.8V, 2.5V, 2.7V) Compatibility Two-wire Serial EEPROM 4K (512 x 8) 8K (1024 x 8)
  • Write Protect Pin for Hardware Data Protection
  • 16-byte Page (4K, 8K) Write Modes
  • Partial Page Writes Allowed
  • Self-timed Write Cycle (5 ms max)
  • High-reliability ─ Endurance: 1 Million Write Cycles ─ Data Retention: 100 Years AT24C04B AT24C08B
  • 8-lead PDIP, 8-lead JEDEC SOIC, 8-lead Ultra-Thin Mini-MAP (MLP 2x3), 5-lead SOT23, 8-lead TSSOP and 8-ball dBGA2 Packages
  • Lead-free/Halogen-free
  • Die Sales: Wafer Form and Tape and Reel

Description

The AT24C04B/08B provides 4096/8192 bits of serial electrically erasable and programmable read-only memory (EEPROM) organized as 512/1024 words of 8 bits each. The device is optimized for use in many industrial and commercial applications where low-power and low-voltage operati on are essential. The AT24C04B/08B is available in space-saving 8-lead PDIP, 8-lead JEDEC SOIC, 8-lead Ultra-Thin Mini- MAP (MLP 2x3), 5-lead SOT23, 8-lead TSSOP, and 8-ball dBGA2 packages and is accessed via a Two-wire serial interface. In addition, the AT24C04B/08B is available in 1.8V (1.8V to 5.5V) version. Figure 1. Pin Configurations

2 AT24C04B/08B

extended periods may affect device reliability. Figure 2. Block Diagram

edge clock data out of each device. wire-ORed with any number of other open-drain or open-collector devices. ground (device addressing is discussed in detail under the Device Addressing section). discussed in detail under the Device Addressing section). Table 1. Write Protect

4 AT24C04B/08B

word address for random word addressing. data word address for random word addressing. Table 2. Pin Capacitance Note: 1. This parameter is characterized and is not 100% tested. Table 3. DC Characteristics Note: 1. V IL min and VIH max are reference only and are not tested.

Table 4. AC Characteristics Note: 1. This parameter is ensured by characterization only.

6 AT24C04B/08B

start or stop condition as defined below. command will place the EEPROM in a standby power mode (see Figure 7). EEPROM sends a zero to acknowledge that it has received each word. This happens during the ninth clock cycle. (b) After the receipt of the STOP bit and the completion of any internal operations. communication after the above steps have been completed. Figure 3. Software reset

8 AT24C04B/08B

Figure 6. Data Validity Figure 7. Start and Stop Definition Figure 8. Output Acknowledge

5226G–SEEPR–11/09 6. Device Addressing The 4K and 8K EEPROM device requires an 8-bit device address word following a start condition to enable the chip for a read or write operation (refer to Figure 9 ). The device address word consists of a mandat ory one, zero sequence for the first four most significant bits as shown. This is common to all the EEPROM devices. The 4K EEPROM only uses the A2 and A1 device address bi ts with the third bit being a memory page address bit. The two device address bits must compare to their corresponding hard-wired input pins. The A0 pin is no connect. The 8K EEPROM only uses the A2 device address bit with the next 2 bits being for memory page addressing. The A2 must compare to its corresponding hard-wired input pin. The A1 and A0 pins are no connect. For the SOT23 Package Offering: The 4K EEPROM software A2 and A1 bits in the device address word must be set to zero to properly communicate. The 8K EEPROM software A2 bit in the device address word must be set to zero to properly communicate. 7. Write Operations BYTE WRITE: A write operation requires an 8-bit data wo rd address following the device address word and acknowledgment. Upon receipt of this address, the EEPROM will again respond with a zero and then clock in the first 8-bit data word. Following receipt of the 8-bit data word, the EEPROM will output a zero and the addressing device, such as a microcontroller, must terminate the write sequence with a stop condition. At this time the EEPROM enters an internally timed write cycle, t WR, to the nonvolatile memory. All inputs are disabled during this write cycle and the EEPROM will not respond until the write is complete (see Figure 10 ). PAGE WRITE: The 4K/8K EEPROM is capable of an 16-byte page write. A page write is initiated the same as a byte write, but the microcontroller does not send a stop condition after the first data word is clocked in. Instead, after the EEPROM acknowledges receipt of the first data word, the microcontroller can transmit up to fifteen data words. The EEPROM will respond with a zero after each data word received. The microcontroller must terminate the page write sequence with a stop condition. (see Figure 11 ). The data word address lower four bits are internally incr emented following the receipt of each data word. The higher data word address bits are not incremented, retaining the memory page row location. When the word address, internally generated, reaches the page bo undary, the following byte is placed at the beginning of the same page. If more than sixteen data words are transmitted to the EEPROM, the data word address will “roll over” and previous data will be overwritten. ACKNOWLEDGE POLLING: Once the internally timed write cycle has st arted and the EEPROM inputs are disabled, acknowledge polling can be initiated. This involves sending a start condition followed by the device address word. The read/write bit is representative of the operation desired. Only if the inte rnal write cycle has completed will the EEPROM respond with a zero allowing the read or write sequence to continue.

10 AT24C04B/08B

generate a following stop condition (see Figure 12). following stop condition (see Figure 14 ). Figure 9. Device Address

12 AT24C04B/08B

Figure 13. Random Read Figure 14. Sequential Read

  1. AT24C04B Ordering Information

Table 5. Ordering Information

1.8 Die Sale Industrial Temperature (-40°C to 85°C)

  1. “-T” denotes tape and reel. SOIC = 4K per reel. TSSOP, Ultra Thin Mini-MAP, SOT23, and dBGA2 = 5K
  2. Available in tape and reel and wafer form; order as SL788 for inkless wafer form. Please contact Serial

14 AT24C04B/08B

  1. AT24C08B Ordering Information

Table 6. Ordering Information

  1. “-T” denotes tape and reel. SOIC = 4K per reel. TSSOP, Ultra Thin Mini-MAP, SOT23, and dBGA2 = 5K
  2. Available in tape and reel and wafer form; order as SL788 for inkless wafer form. Please contact Serial

5226G–SEEPR–11/09 11. Part Marketing Scheme 11.1. AT24C04B Device Package Marking 8-PDIP Seal Year Top Mark Seal Week Y = SEAL YEAR WW = SEAL WEEK 6: 2006 0: 2010 02 = Week 2 --- --- --- --- --- --- --- --- 7: 2007 1: 2011 04 = Week 4 A T M L U Y W W --- --- --- --- --- --- --- B 50 = Week 50 Lot Number 52 = Week 52 --- --- --- --- --- --- --- --- Lot Number to Use ALL Characters in Marking BOTTOM MARK Pin 1 Indicator (Dot) No Bottom Mark 8-SOIC Seal Year Top Mark Seal Week Y = SEAL YEAR WW = SEAL WEEK 6: 2006 0: 2010 02 = Week 2 --- --- --- --- --- --- --- --- 7: 2007 1: 2011 04 = Week 4 A T M L H Y W W --- --- --- --- --- --- --- B 50 = Week 50 Lot Number 52 = Week 52 --- --- --- --- --- --- --- --- Lot Number to Use ALL Characters in Marking BOTTOM MARK Pin 1 Indicator (Dot) No Bottom Mark 8-TSSOP Top Mark Pin 1 Indicator (Dot) Y = SEAL YEAR WW = SEAL WEEK 6: 2006 0: 2010 02 = Week 2 W W --- --- --- --- B 50 = Week 50 --- --- --- --- --- 52 = Week 52 Bottom Mark --- --- --- --- --- --- --- --- P H A A A A A A A A Pin 1 Indicator

16 AT24C04B/08B

5226G–SEEPR–11/09 8-Ultra Thin Mini Map Top Mark Y = YEAR OF ASSEMBLY --- --- --- 0 4 B XX = ATMEL LOT NUMBER TO COORESPOND WITH --- --- --- NSEB TRACE CODE LOG BOOK. H 1 --- --- --- Y X X --- --- --- Y = SEAL YEAR 6: 2006 0: 2010 7: 2007 1: 2011 Pin 1 Indicator (Dot) 8: 2008 2: 2012 9: 2009 3: 2013 ULA Top Mark --- --- --- 0 4 B --- --- --- Y X X --- --- --- Pin 1 Indicator (Dot) Y = BUILD YEAR 2006 = 6 2008 = 8 XX = ATMEL LOT NUMBER TO COORESPOND WITH NSEB TRACE CODE LOG BOOK.

5226G–SEEPR–11/09 SOT23 Top Mark --- --- --- --- --- B B U XX = Device V = Voltage Indicator W = Write Protect Feature U = Material Set Pin 1 Indicator (Dot) Bottom Mark --- --- --- --- Y M T C --- --- --- --- Y = One Digit Year Code M = Seal Month (Use Alpha Designator A-L) TC = Trace Code dBGA2 Top Mark 04BU <--- Pin 1 This Corner XXX = Device U = Material Set Y = One Digit Year Code M = Seal Month (Use Alpha Designator A-L) TC = Trace Code

18 AT24C04B/08B

5226G–SEEPR–11/09 11.2. AT24C08B Device Package Marking dBGA2 Top Mark 08BU <--- Pin 1 This Corner Y = ONE DIGIT YEAR CODE 8: 2008 1: 2011 9: 2009 2: 2012 0: 2010 3: 2013 M = SEAL MONTH (USE ALPHA DESIGNATOR A-L) A = JANUARY B = FEBRUARY J = OCTOBER K = NOVEMBER L = DECEMBER XX = TRACE CODE (ATMEL LOT NUMBERS TO CORRESPOND WITH ATK TRACE CODE LOG BOOK) 8-Ultra Thin Mini MAP Top Mark --- --- --- B --- --- --- H 1 --- --- --- Y X X --- --- --- Pin 1 Indicator (Dot) Y = YEAR OF ASSEMBLY XX = TRACE ATMEL LOT NUMBER TO COORESPOND WITH TRACE CODE LOG BOOK. Y = SEAL YEAR 6: 2006 0: 2010 7: 2007 1: 2011 8: 2008 2: 2012 9: 2009 3: 2013

5226G–SEEPR–11/09 8-PDIP and 8-SOIC Seal Year Top Mark Seal Week --- --- --- --- --- --- --- --- A T M L H Y W W --- --- --- --- --- --- --- --- B Lot Number --- --- --- --- --- --- --- --- Pin 1 Indicator (Dot) Y = SEAL YEAR WW = SEAL WEEK 8: 2008 2: 2012 02 = Week 2 9: 2009 3: 2013 04 = Week 4 50 = Week 50 52 = Week 52 SOT23 Top Mark --- --- --- --- --- B B U Pin 1 Indicator (Dot) BACKSIDE MARKING --- --- --- --- Y M X X --- --- --- --- Y = ONE DIGIT YEAR CODE 4: 2004 7: 2007 5: 2005 8: 2008 6: 2006 9: 2009 M = SEAL MONTH (USE ALPHA DESIGNATOR A-L) A = JANUARY B = FEBRUARY J = OCTOBER K = NOVEMBER L = DECEMBER XX = TRACE CODE (ATMEL LOT NUMBERS TO CORRESPOND WITH TRACE CODE LOG BOOK)

20 AT24C04B/08B

5226G–SEEPR–11/09 8-TSSOP Pin 1 Indicator (Dot) --- --- --- --- W W H Y --- --- --- --- --- B --- --- --- --- --- Bottom Mark --- --- --- --- --- --- --- C O O A A A A A A A Pin 1 Indicator COO = Country of Origin Y = SEAL YEAR WW = SEAL WEEK 6: 2006 0: 2010 02 = Week 2 7: 2007 1: 2011 04 = Week 4 9: 2009 3: 2013 :: : :::: :: 50 = Week 50 52 = Week 52

Figure 15. 8P3 – PDIP

2325 Orchard Parkway

Notes: 1. This drawing is for general information only; refer to JEDEC D rawing MS-001, Variation BA, for additional information.

  1. Dimensions A and L are measured with the pa ckage seated in JEDEC seating plane Gauge GS-3.
  2. D, D1 and E1 dimensions do not include mold Flash or protrusions. Mold Flash or protrusions shall not exceed 0.010 inch.
  3. E and eA measured with the leads constrained to be perpendicular to datum.
  4. Pointed or rounded lead tips are pre ferred to ease insertion.

4 PLCS

22 AT24C04B/08B

Figure 16. 8S1 – JEDECSOIC These drawings are for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc.

Figure 17. 8A2 – TSSOP

  1. Dimension D does not include mold Flash, protrusions or gate burrs. Mold Flash, protrusions and gate burrs shall not exceed
  2. Dimension E1 does not include inter-lead Flash or protrusions. Inter-lead Flash and protrusions shall not exceed 0.25 mm
  3. Dimension b does not include Dambar protrusion. Allowable Dambar protrusion shall be 0.08 mm total in excess of the

protrusion and adjacent lead is 0.07 mm.

  1. Dimension D and E1 to be determined at Datum Plane H.

24 AT24C04B/08B

Figure 18. 8Y6 – Mini Map

  1. Dimension b applies to metallized terminal and is measured between 0.15 mm and 0.30 mm from the te rminal tip. If the

terminal has the optional radius on the other end of the te rminal, the dimension should not be measured in thatradius area.

  1. Soldering the large thermal pad is optional, but not recommended. No electrical connection is accomplished to the

Figure 19. 5TS1 – SOT23 MO-193, Variation A B, for additional in formation.

  1. Dimension D does not include mold flash, prot rusions, or gate burrs.

Mold flash, prot rusions, or gate burrs shall not exceed 0.15 mm per end. flash or prot rusion shall not exceed 0.15 mm per sid e.

  1. The package top m ay be smaller than the pa ckage bottom . Dimensions

including a ny mismatch bet ween the top and bottom of the plastic bod y.

  1. These dimensions apply to the flat section of the lead bet ween 0.08 mm

and 0.15 mm from the lead ti p.

  1. Dimension "b" does not include Dambar prot rusion. Allowable Dambar

shall not be less than 0.07 mm.

26 AT24C04B/08B

Figure 20. 8U3-1 – Dbga2 1150 E . Cheyenne Mtn . Blvd.

  1. Dimension “b” is measured at the maxi mum solder ball diamete r.

This drawing is for general information only.

8 SOLDER BALLS

Table 7. Revision History 5226E 12/2008 Add AT24C08B Device Package Marking Details and removed Bumped wafer offering. 5226D 08/2008 Update into MS Format.

5226G–SEEPR–11/09 Headquarters International Atmel Corporation San Jose, CA 95131 USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Atmel Asia Room 1219 Chinachem Golden Plaza

77 Mody Road Tsimshatsui

Tel: (852) 2721-9778 Fax: (852) 2722-1369 Atmel Europe Le Krebs 8, Rue Jean-Pierre Timbaud BP 309

78054 Saint-Quentin-en-

9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Product Contact Web Site www.atmel.com Technical Support s_eeprom@atmel.com Sales Contact www.atmel.com/contacts Literature Requests www.atmel.com/literature Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or im plied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DI RECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDEN-TAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to th e accuracy or completeness of th e contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not ma ke any commitment to update the information contained herein. Unless specifically provided other wise, Atmel products are not suit able for, and shall not be use d in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. © 2009 Atmel Corporation. All rights reserved. Atmel®, Atmel logo and combinations thereof, and others are registered trademark s or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.