AT24C04A_14 ATMEL

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 16

Technical content

Features

  • Write Protect Pin for Hardware Data Protection – Utilizes Different Array Protection Compared to the AT24C02A/04A
  • Standard-voltage Operation – 2.7 (V CC = 2.7V to 5.5V)
  • Internally Organized 256 x 8 (2K), 512 x 8 (4K)
  • Two-wire Serial Interface
  • Schmitt Trigger, Filtered Inputs for Noise Suppression
  • Bidirectional Data Transfer Protocol
  • 400 kHz Clock Rate
  • 8-byte Page (2K), 16-byte Page (4K) Write Modes
  • Partial Page Writes Allowed
  • Self-timed Write Cycle (5 ms Max)
  • High Reliability – Endurance: One Million Write Cycles – Data Retention: 100 Years
  • Lead-Free/Halogen-Free Devices Available
  • 8-lead JEDEC SOIC and 8-lead TSSOP Packages

Description

The AT24C02A/04A provides 2048/4096 bits of serial electrically erasable and pro- grammable read-only memory (EEPROM) organized as 256/512 words of 8 bits each. The device is optimized for use in many automotive applications where low-power and low-voltage operation are essential. The AT24C02A/04A is available in space-saving 8-lead JEDEC SOIC and 8-lead TSSOP pack ages and is accessed via a two-wire Two-wire Automotive Temperature Serial EEPROM 2K (256 x 8) 4K (512 x 8) AT24C02A(1) AT24C04A Note: 1. AT24C02A not recom- mended for new design; please refer to the AT24HC02B Auto- motive datasheet. 5083D–SEEPR–4/07 Table 1. Pin Configurations

2 AT24C02A/04A

Figure 1. Block Diagram EEPROM device and negative edge clock data out of each device. under Device Addressing, page 7). 4K devices may be addressed on a single bus system. The A0 pin is a no-connect.

Table 1. Write Protect bytes each. Random word addressing requires an 8-bit data word address. bytes each. Random word addressing requires a 9-bit data word address. Note: This parameter is characterized and is not 100% tested. Note: 1. V IL min and VIH max are reference only and are not tested. Table 2. Pin Capacitance Table 3. DC Characteristics

4 AT24C02A/04A

Note: 1. This parameter is characterized and is not 100% tested (T A = 25°C).

  1. This parameter is characterized and is not 100% tested.

Table 4. AC Characteristics

6 AT24C02A/04A

  1. Look for SDA high in each cycle while SCL is high.
  2. Create a start condition as SDA is high.

Figure 4. Bus Timing Figure 5. Write Cycle Timing Note: The writ e cycle time tWR is the time from a valid stop condition of a write sequence to the end of the interval clear/write cycle.

Figure 6. Output Acknowledge start condition to enable the chip for a read or write operation, as shown in Figure 7. Figure 7. Device Address most significant bits as shown. This is common to all the EEPROM devices. The next three bits are the A2, A1, and A0 device address bits for the 2K EEPROM. These three bits must compare to their corresponding hardwired input pins. sponding hardwired input pins. The A0 pin is no-connect. tion is initiated if this bit is high, and a write operation is initiated if this bit is low. not made, the chip will return to a standby state.

1 A2 A0A1 R/W

8 AT24C02A/04A

write is complete, as shown in Figure 8. Figure 8. Byte Write EEPROM device is capable of 16-byte page writes. stop condition, as shown in Figure 9. Figure 9. Page Write will the EEPROM respond with a “0” allowing the read or write sequence to continue.

10 AT24C02A/04A

Figure 12. Sequential Read

5083D–SEEPR–4/07 Note: 1. This device is not recommended for new design . Please refer to AT24HC02B Automotive datasheet. Ordering Code Package Operation Range AT24C02AN-10SQ-2.7 AT24C02A-10TQ-2.7 8S1 8A2 Lead-free/Halogen-free/ Automotive Temperature (−40°C to 125°C) Package Type 8S1 8-lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 8A2 8-lead, 0.170" Wide, Thin Shrink Small Outline Package (TSSOP) Options −2.7 Low Voltage (2.7V to 5.5V)

12 AT24C02A/04A

5083D–SEEPR–4/07 Ordering Code Package Operation Range AT24C04A-10TQ-2.7 AT24C04AN-10SQ-2.7 8A2 8S1 Lead-free/Halogen-free Automotive Temperature (−40°C to 125°C) Package Type 8S1 8-lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 8A2 8-lead, 0.170" Wide, Thin Shrink Small Outline Package (TSSOP) Options −2.7 Low Voltage (2.7V to 5.5V)

5083D–SEEPR–4/07 Packaging Information 8S1 – JEDEC SOIC 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TITLE DRAWING NO. R REV. Note: 10/7/03 8S1, 8-lead (0.150" Wide Body), Plastic Gull Wing Small Outline (JEDEC SOIC) 8S1 B COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A1 0.10 – 0.25 These drawings are for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. A 1.35 – 1.75 b 0.31 – 0.51 C 0.17 – 0.25 D 4.80 – 5.00 E1 3.81 – 3.99 E 5.79 – 6.20 e 1.27 BSC L 0.40 – 1.27 ∅ 0° – 8° Top View End View Side View e B D A N E C L

14 AT24C02A/04A

5083D–SEEPR–4/07 8A2 – TSSOP

2325 Orchard Parkway

San Jose, CA 95131 TITLE DRAWING NO. R REV. 5/30/02 COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE D 2.90 3.00 3.10 2, 5 E 6.40 BSC E1 4.30 4.40 4.50 3, 5 A – – 1.20 A2 0.80 1.00 1.05 b 0.19 – 0.30 4 e 0.65 BSC L 0.45 0.60 0.75 L1 1.00 REF 8A2, 8-lead, 4.4 mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-153, Variation AA, for proper dimensions, tolerances, datums, etc. 2. Dimension D does not include mold Flash, protrusions or gate burrs. Mold Flash, protrusions and gate burrs shall not exceed 0.15 mm (0.006 in) per side. 3. Dimension E1 does not include inter-lead Flash or protrusions. Inter-lead Flash and protrusions shall not exceed 0.25 mm (0.010 in) per side. 4. Dimension b does not include Dambar protrusion. Allowable Dambar protrusion shall be 0.08 mm total in excess of the b dimension at maximum material condition. Dambar cannot be located on the lower radius of the foot. Minimum space between protrusion and adjacent lead is 0.07 mm. 5. Dimension D and E1 to be determined at Datum Plane H. 8A2 B Side View End ViewTop View A L D 123 N b Pin 1 indicator this corner E e

5083D–SEEPR–4/07

Revision History

Doc. Rev. Date Comments 5093D 4/2007 Added ‘Not recommended for new design’ note to page 1 and 11 for AT24C02A 5093C 1/2007 Implemented revision history Remove PDIP package offering Remove PB’d parts

Printed on recycled paper. 5083D–SEEPR–4/07 Disclaimer: The information in this document is provided in connection with Atmel products. No license, expr ess or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LI ABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTOR Y WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO , THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICU LAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR I NCIDEN- TAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTE RRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or comp leteness of the contents of th is document and reserves the rig ht to make changes to specifications and product descriptions at any time withou t notice. Atmel does not make any commitm ent to update the information contained her ein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not int ended, authorized, or warranted for use as components in applications intended to support or sustain life. Atmel Corporation Atmel Operations San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Regional Headquarters Europe Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland Tel: (41) 26-426-5555 Fax: (41) 26-426-5500 Asia Room 1219 Chinachem Golden Plaza

77 Mody Road Tsimshatsui

Tel: (852) 2721-9778 Fax: (852) 2722-1369 Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Memory San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 Microcontrollers San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 La Chantrerie BP 70602

44306 Nantes Cedex 3, France

13106 Rousset Cedex, France

1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland Tel: (44) 1355-803-000 Fax: (44) 1355-242-743 RF/Automotive Theresienstrasse 2 Postfach 3535

74025 Heilbronn, Germany

1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom Avenue de Rochepleine BP 123

38521 Saint-Egreve Cedex, France

www.atmel.com/literature © 2007 Atmel Corporation. All rights reserved. Atmel ®, logo and combinations thereof, and others, are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.