AT24C01ASC ATMEL

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 14

Technical content

Features

 Low-voltage and Standard-voltage Operation, VCC = 2.7V–5.5V  Internally Organized 128 x 8 (1K), 256 x 8 (2K), 512 x 8 (4K), 1024 x 8 (8K), or 2048 x 8 (16K)  Two-wire Serial Interface  Schmitt Trigger, Filtered Inputs for Noise Suppression  Bidirectional Data Transfer Protocol  400 kHz Compatibility  8-byte Page (1K, 2K), 16-byte Page (4K, 8K, 16K) Write Modes  Partial Page Writes Allowed  Self-timed Write Cycle (5 ms max)  High Reliability – Endurance: One Million Write Cycles – Data Retention: 100 Years – ESD Protection: >3000V

Description

The AT24C01A/02SC/04SC/08SC/16SC provide 1024/2048/4096/8192/16384 bits of serial, electrically-erasable, and programmable read-only memory (EEPROM) orga- nized as 128/256/512/1024/2048 words of 8 bits each. The devices are optimized for use in smart card applications where low-power and low-voltage operation may be essential. The devices are available in several standard ISO 7816 smart card modules (see Ordering Information, pages 12–13). All devices are functionally equivalent to Atmel serial EEPROM products offered in standard IC packages (PDIP , SOIC, TSSOP , MAP), with the exception of the slave address and write protect functions, which are not required for smart card applications. Table 1. Pin Configuration Figure 1. Card Module Contact

2 AT24C01ASC/02SC/04SC/08SC/16SC

Figure 2. Block Diagram EEPROM device and negative edge clock data out of each device. each, the 1K requires a 7-bit data word address for random word addressing. each, the 2K requires an 8-bit data word address for random word addressing.

each, the 4K requires a 9-bit data word address for random word addressing. each, the 8K requires a 10-bit data word address random word addressing. each, the 16K requires an 11-bit data word address random word addressing. Note: 1. This parameter is characterized and is not 100% tested.

  1. VIL min and VIH max are reference only and are not tested.

Table 2. Pin Capacitance(1) Table 3. DC Characteristics(1) Table 4. AC Characteristics(1)

4 AT24C01ASC/02SC/04SC/08SC/16SC

  1. This parameter is characterized and is not 100% tested.

that must precede any other command (see Figure 4 on page 6). STOP CONDITION: A low-to-high transition of SDA with SCL high is a stop condition. mode (see Figure 4 on page 6). the EEPROM will disable the read operation and return to standby mode. completion of any internal operations.

  1. Look for SDA high in each cycle while SCL is high.
  2. Create a start condition as SDA is high.

Table 4. AC Characteristics(1) (Continued)

AT24C01ASC/02SC/04SC/08SC/16SC 1610B–SEEPR –04/04 Timing Diagrams Bus Timing Figure 1. Bus Timing Note: SCL: Serial Clock, SDA: Serial Data I/O Write Cycle Timing Figure 2. Write Cycle Timing Notes: 1. The write cycle time tWR is the time from a valid stop condition of a write sequence to the end of the internal clear/write cycle. 2. SCL: Serial Clock, SDA: Serial Data I/O Data Validity Figure 3. Data Validity tWR (1) SDA SCL DATA STABLE DATA CHANGE DATA STABLE

6 AT24C01ASC/02SC/04SC/08SC/16SC

1610B–SEEPR –04/04 Start and Stop DefinitionFigure 4. Start and Stop Definition Output Acknowledge Figure 5. Output Acknowledge DA CL START STOP SCL DATA IN DATA OUT START ACKNOWLEDGE

four most significant bits as shown. This is common to all the serial EEPROM devices. three unused bits of the device address word should be set to “0”. tion is initiated if this bit is high, and a write operation is initiated if this bit is low. cessful compare is not made, the chip will return to a standby state (NO ACK). Figure 6. Device Address

101000 P 0 R / W

8 AT24C01ASC/02SC/04SC/08SC/16SC

not respond until the write is complete (refer to Figure 7). Figure 7. Byte Write and 16K devices are capable of 16-byte page writes. sequence with a stop condition (refer to Figure 8). Figure 8. Page Write

10 AT24C01ASC/02SC/04SC/08SC/16SC

stop condition (refer to Figure 11). Figure 11. Sequential Read

AT24C01ASC/02SC/04SC/08SC/16SC 1610B–SEEPR –04/04 Ordering Code Package Voltage Range Operation Range A T24C01ASC-09ET M2 – E Module 2.7V –5.5V Commercial (0 °C –70°C) A T24C01ASC-09GT M3 – G Module 2.7V –5.5V Commercial (0 °C –70°C) A T24C01ASC-09HT M3 – H Module 2.7V –5.5V Commercial (0 °C –70°C) A T24C01ASC-09PT M2 – P Module 2.7V –5.5V Commercial (0 °C –70°C) A T24C01ASC-10WI 7 mil Wafer 2.7V –5.5V Industrial ( −40°C –85°C) Ordering Code Package Voltage Range Operation Range A T24C02SC-09ET M2 – E Module 2.7V –5.5V Commercial (0 °C –70°C) A T24C02SC-09PT M2 – PModule 2.7V –5.5V Commercial (0 °C –70°C) A T24C02SC-10WI 7 mil Wafer 2.7V –5.5V Industrial ( −40°C –85°C) Ordering Code Package Voltage Range Operation Range A T24C04SC-09ET M2 – E Module 2.7V –5.5V Commercial (0 °C –70°C) A T24C04SC-09PT M2 – PModule 2.7V –5.5V Commercial (0 °C –70°C) A T24C04SC-10WI 7 mil Wafer 2.7V –5.5V Industrial ( −40°C –85°C) Ordering Code Package Voltage Range Operation Range A T24C08SC-09ET M2 – E Module 2.7V –5.5V Commercial (0 °C –70°C) A T24C08SC-09PT M2 – PModule 2.7V –5.5V Commercial (0 °C –70°C) A T24C08SC-10WI 7 mil Wafer 2.7V –5.5V Industrial ( −40°C –85°C) Ordering Code Package Voltage Range Operation Range A T24C16SC-09ET M2 – E Module 2.7V –5.5V Commercial (0 °C –70°C) A T24C16SC-09PT M2 – PModule 2.7V –5.5V Commercial (0 °C –70°C) A T24C16SC-10WI 7 mil Wafer 2.7V –5.5V Industrial ( −40°C –85°C)

12 AT24C01ASC/02SC/04SC/08SC/16SC

1610B–SEEPR –04/04 Note: 1. Formal drawings may be obtained from an Atmel sales office. Package Type(1) Description M2 – P Module M2 ISO 7816 Smart Card Module with Atmel Logo M2 – E Module M2 ISO 7816 Smart Card Module M3 – G Module M3 ISO 7816 Smart Card Module M3 – H Module M3 ISO 7816 Smart Card Module with Atmel Logo

AT24C01ASC/02SC/04SC/08SC/16SC 1610B–SEEPR –04/04 Smart Card Modules *Note: The module dimensions listed refer to the dimensions of the exposed metal contact area. The actual dimensions of the module after excise or punching from the carrier tape are generally 0.4 mm greater in both directions Module Size: M2-00 Dimension*: 12.6 x 11.4 [mm] Thickness: 0.58 [mm] max Pitch: 14.25 [mm] Glob Top: Clear, Round: 8.0 [mm] max/KC6 Ordering Code: 09ET-00 Module Size: M3 Dimension*: 10.6 x 8.0 [mm] Thickness: 0.58 [mm] max Pitch: 9.5 [mm] Glob Top: Clear, Round: 6.9 [mm] max/KC6 Ordering Code: 09GT-00 Module Size: M2 Dimension*: 12.6 x 11.4 [mm] Glob Top: Square: 8.8 x 8.8 [mm] Thickness: 0.58 [mm] Pitch: 14.25 [mm] Ordering Code: 09PT-00 Module Size: M3 Dimension*: 10.6 x 8.0 [mm] Thickness: 0.58 [mm] max Pitch: 9.5 [mm] Glob Top: Clear, Round: 6.9 [mm]/KC6 Ordering Code: 09HT-00

Printed on recycled paper. Disclaimer: Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company ’s standard warranty which is detailed in Atmel’s T erms and Conditions located on the Company’s web site. The Company assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not authorized for use as critical components in life support devices or systems. Atmel Corporation Atmel Operations

2325 Orchard Parkway

San Jose, CA 95131 Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Regional Headquarters Europe Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland Tel: (41) 26-426-5555 Fax: (41) 26-426-5500 Asia Room 1219 Chinachem Golden Plaza

77 Mody Road Tsimshatsui

Tel: (852) 2721-9778 Fax: (852) 2722-1369 Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Memory San Jose, CA 95131 Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 Microcontrollers San Jose, CA 95131 Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 La Chantrerie BP 70602

44306 Nantes Cedex 3, France

13106 Rousset Cedex, France

1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland Tel: (44) 1355-803-000 Fax: (44) 1355-242-743 RF/Automotive Theresienstrasse 2 Postfach 3535

74025 Heilbronn, Germany

1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom Avenue de Rochepleine BP 123

38521 Saint-Egreve Cedex, France

literature@atmel.com Web Site http://www.atmel.com 1610B–SEEPR –04/04 © Atmel Corporation 2003. All rights reserved. Atmel® and combinations thereof are registered trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be the trademarks of others.