AT24C01B_09 ATMEL

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 20

Technical content

  1. Features
  • Medium-voltage and Standard-voltage Operation – 2.5 (V CC = 2.5V to 5.5V)  Automotive Temperature Range –40°C to 125°C  Internally Organized 128 x 8 (1K), 256 x 8 (2K), 512 x 8 (4K) or 1024 x 8 (8K)  Two-wire Serial Interface  Schmitt Trigger, Filtered Inputs for Noise Suppression  Bidirectional Data Transfer Protocol  400 kHz (2.5V) Compatibility  Write Protect Pin for Hardware Data Protection  8-byte Page (1K, 2K) or 16-byte Page (4K, 8K) Write Modes  Partial Page Writes are Allowed  Self-timed Write Cycle (5 ms max)  High-reliability – Endurance: 1 Million Write Cycles – Data Retention: 100 Years  8-lead JEDEC SOIC and 8-lead TSSOP Packages 2. Description The AT24C01B/02B/04B/08B provides 1024/2048/4096/8192 bits of serial electrically erasable and programmable read-only memory (EEPROM) organized as 128/256/512/1024 words of 8 bits each. The device is optimized for use in many auto- motive applications where low-power and low-voltage operation are essential. The AT24C01B/02B/04B/08B is available in space-saving 8-lead JEDEC SOIC and 8-lead TSSOP packages and is accessed via a two-wire serial interface. In addition, the entire family is available in 2.5V (2.5V to 5.5V) versions. Table 2-1. Pin Configurations Pin Name Function A0 − A2 Address Inputs SDA Serial Data SCL Serial Clock Input WP Write Protect Two-wire Automotive Temperature Serial EEPROM 1K (128 x 8) 2K (256 x 8) 4K (512 x 8) 8K (1024 x 8) AT24C01B AT24C02B AT24C04B AT24C08B 8517C–SEEPR–01/09 8-lead SOIC GND VCC WP SCL SDA 8-lead TSSOP GND VCC WP SCL SDA

8517C–SEEPR–01/09 AT24C01B/02B/04B/08B Figure 3-1. Block Diagram 3. Absolute Maximum Ratings Maximum Ratings” may cause permanent dam- age to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Voltage on Any Pin START STOP LOGIC VCC GND WP SCL SDA SERIAL CONTROL LOGIC EN H.V. PUMP/TIMING EEPROM DATA RECOVERY SERIAL MUX X DEC DOUT/ACK LOGIC COMP LOAD INC DATA WORD ADDR/COUNTER Y DEC R/W DOUT DIN LOAD DEVICE ADDRESS COMPARATOR

8517C–SEEPR–01/09 AT24C01B/02B/04B/08B 4. Pin Description SERIAL CLOCK (SCL): The SCL input is used to positive edge clock data into each EEPROM device and negative edge clock data out of each device. SERIAL DATA (SDA): The SDA pin is bi-directional for serial data transfer. This pin is open- drain driven and may be wire-ORed with any number of other open-drain or open-collector devices. DEVICE/PAGE ADDRESSES (A2, A1, A0): The A2, A1 and A0 pins are device address inputs that are hard wired for the AT24C01B/02B/04B . As many as eight 1K/2K devices may be addressed on a single bus system (device addressing is discussed in detail under the Device Addressing section). The AT24C04B uses the A2 and A1 inputs for hardwire addressing and a total of four 4K devices may be addressed on a single bus system. The A0 pin is a no connect. The AT24C08B only uses the A2 input for hard wire addressing and a total of two 8K devices may be addressed on a single bus system. The A0 and A1 pins are no connect. WRITE PROTECT (WP): The AT24C01B/02B/04B/08B has a Write Protect pin that provides hardware data protection. The Write Protect pi n allows normal read/write operations when con- nected to ground (GND). When the Write Protect pin is connected to V CC, the write protection feature is enabled and operates as shown in the following table. 5. Memory Organization AT24C01B, 1K SERIAL EEPROM: Internally organized with 16 pages of 8 bytes each, the 1K requires a 7-bit data word address for random word addressing. AT24C02B, 2K SERIAL EEPROM : Internally organized with 32 pages of 8 bytes each, the 2K requires an 8-bit data word address for random word addressing. AT24C04B, 4K SERIAL EEPROM: Internally organized with 32 pages of 16 bytes each, the 4K requires a 9-bit data word address for random word addressing. AT24C08B, 8K SERIAL EEPROM: Internally organized with 64 pages of 16 bytes each, the 8K requires a 10-bit data word address for random word addressing. Table 4-1. Write Protect WP Pin Status Part of the Array Protected AT24C01B/02B/04B/08B At VCC Full Array At GND Normal Read/Write Operations

8517C–SEEPR–01/09 AT24C01B/02B/04B/08B Note: 1. This parameter is characterized and is not 100% tested. Note: 1. V IL min and VIH max are reference only and are not tested. Table 5-1. Pin Capacitance(1) Applicable over recommended operating range from TA = 25°C, f = 400 KHz, VCC = +2.5V Symbol Test Condition Max Units Conditions CI/O Input/Output Capacitance (SDA) 8 pF V I/O = 0V CIN Input Capacitance (A0, A1, A2, SCL) 6 pF V IN = 0V Table 5-2. DC Characteristics Applicable over recommended operating range from: TA = −40°C to +125°C, VCC = +2.5V to +5.5V (unless otherwise noted) Symbol Parameter Test Condition Min Typ Max Units VCC1 Supply Voltage 2.5 5.5 V ICC Supply Current VCC = 5.0V Read at 100 kHz 0.4 1.0 mA ICC Supply Current VCC = 5.0V Write at 100 kHz 2.0 3.0 mA ISB1 Standby Current VCC = 2.5V V IN = VCC or VSS 1.6 4.0 µA ISB2 Standby Current VCC = 5.0V V IN = VCC or VSS 8.0 18.0 µA ILI Input Leakage Current V IN = VCC or VSS 0.10 3.0 µA ILO Output Leakage Current V OUT = VCC or VSS 0.05 3.0 µA VIL Input Low Level(1) −0.6 V CC x 0.3 V VIH Input High Level(1) VCC x 0.7 V CC + 0.5 V VOL Output Low Level VCC = 2.5V I OL = 3.0 mA 0.4 V

8517C–SEEPR–01/09 AT24C01B/02B/04B/08B Notes: 1. This parameter is characterized and is not 100% tested (T A = 25°C). 2. This parameter is characterized only. Table 5-3. AC Characteristics Applicable over recommended operating range from T A = −40°C to +125°C, VCC = +2.5V to +5.5V, CL = 1 TTL Gate and 100 pF (unless otherwise noted) Symbol Parameter Min Max Units fSCL Clock Frequency, SCL 400 kHz tLOW Clock Pulse Width Low 1.2 µs tHIGH Clock Pulse Width High 0.6 µs tI Noise Suppression Time(1) 50 ns tAA Clock Low to Data Out Valid 0.1 0.9 µs tBUF Time the bus must be free before a new transmission can start(2) 1.2 µs tHD.STA Start Hold Time 0.6 µs tSU.STA Start Set-up Time 0.6 µs tHD.DAT Data In Hold Time 0 µs tSU.DAT Data In Set-up Time 100 ns tR Inputs Rise Time(2) 300 ns tF Inputs Fall Time(2) 300 ns tSU.STO Stop Set-up Time 0.6 µs tDH Data Out Hold Time 50 ns tWR Write Cycle Time 5 ms Endurance(2) 5.0V, 25°C, Page Mode 1M Write Cycles

8517C–SEEPR–01/09 AT24C01B/02B/04B/08B 6. Device Operation CLOCK and DATA TRANSITIONS: The SDA pin is normally pulled high with an external device. Data on the SDA pin may change only during SCL low time periods (see Figure 8-2 on page 8). Data changes during SCL high periods will indicate a start or stop condition as defined below. START CONDITION: A high-to-low transition of SDA with SCL high is a start condition which must precede any other command (see Figure 8-3 on page 8). STOP CONDITION: A low-to-high transition of SDA with SCL high is a stop condition. After a read sequence, the stop command will place the EEPROM in a standby power mode (see Fig- ure 8-3 on page 8). ACKNOWLEDGE: All addresses and data words are serially transmitted to and from the EEPROM in 8-bit words. The EEPROM sends a “0” to acknowledge that it has received each word. This happens during the ninth clock cycle. STANDBY MODE: The AT24C01B/02B/04B/08B features a low-power standby mode which is enabled: (a) upon power-up and (b) after the receipt of the STOP bit and the completion of any internal operations. 2-WIRE SOFTWARE RESET: After an interruption in protocol, power loss or system reset, any 2-wire part can be protocol reset by following thes e steps: (a) Create a start bit condition, (b) clock 9 cycles, (c) create another start but foll owed by stop bit condition as shown below. The device is ready for next communication after above steps have been completed. Figure 6-1. Software Reset Start bit Stop bitStart bitDummy Clock Cycles SCL SDA 12 38 9

8517C–SEEPR–01/09 AT24C01B/02B/04B/08B 9. Device Addressing The 1K/2K/4K/8K EEPROM device requires an 8-bit device address word following a start con- dition to enable the chip for a read or write operation (see Figure 11-1 on page 10). The device address word consists of a mandatory “1”, “0” sequence for the first four most signif- icant bits as shown. This is common to all the Serial EEPROM devices. The next 3 bits are the A2, A1 and A0 device address bits for the 1K/2K EEPROM. These 3 bits must compare to their corresponding hardwired input pins. The 4K EEPROM only uses the A2 and A1 device address bits wi th the A0 bit being a memory address bit (P0) (see Figure 11-1 on page 10 ). The two device address bits must compare to their corresponding hardwired input pins. The A0 pin is no connect. The 8K EEPROM only uses the A2 device address bit with the next two bits (P9, P0) being for memory page addressing (See Figure 11-1 on page 10 ). The A2 bit must compare to its corre- sponding hardwired input pin. The A1 and A0 pins are no connect. The eighth bit of the device address is the read/write operation select bit. A read operation is ini- tiated if this bit is high and a write operation is initiated if this bit is low. Upon a compare of the device address, the EEPROM will output a “0”. If a compare is not made, the chip will return to a standby state. 10. Write Operations BYTE WRITE: A write operation requires an 8-bit data word address following the device address word and acknowledgment. Upon receipt of this address, the EEPROM will again respond with a “0” and then clock in the first 8-bit data word. Following receipt of the 8-bit data word, the EEPROM will output a “0” and the addressing device, such as a microcontroller, must terminate the write sequence with a stop condition. At this time the EEPROM enters an internally timed write cycle, t WR, to the nonvolatile memory. All inputs are disabled during this write cycle and the EEPROM will not respond until the write is complete (see Figure 11-2 on page 11). PAGE WRITE: The 1K/2K EEPROM is capable of an 8-by te page write. The 4K/8K devices are capable of 16-byte page writes. A page write is initiated the same as a byte write, but the microcontroller does not send a stop condition after the first data word is clocked in. Instead, after the EEPROM acknowledges receipt of the first data word, the microcontroller can transmit up to seven (1K/2K) or fifteen (4K/ 8K) more data words. The EEPROM will respond with a “0” after each data word received. The microcontroller must terminate the page write sequence with a stop condition (see Figure 11-3 on page 11). The data word address lower three (1K/2K) or four (4K/8K) bits are internally incremented fol- lowing the receipt of each data word. The higher data word address bits are not incremented, retaining the memory page row location. When the word address, internally generated, reaches the page boundary, the following byte is placed at the beginning of the same page. If more than eight (1K/2K) or sixteen (4K/8K) data words are transmitted to the EEPROM, the data word address will “roll over” and previous data will be overwritten. ACKNOWLEDGE POLLING: Once the internally timed write cycle has started and the EEPROM inputs are disabled, ackno wledge polling can be initiate d. This involves sending a start condition followed by the device address word. The read/write bit is representative of the

8517C–SEEPR–01/09 AT24C01B/02B/04B/08B operation desired. Only if th e internal write cycle has comp leted will the EEPROM respond with a “0”, allowing the read or write sequence to continue. 11. Read Operations Read operations are initiated the same way as write operations with the exception that the read/write select bit in the device address word is set to “1”. There are three read operations: current address read, random address read and sequential read. CURRENT ADDRESS READ: The internal data word address counter maintains the last address accessed during the last read or write operation, incremented by one. This address stays valid between operations as long as the chip power is maintained. The address “roll over” during read is from the last byte of the last memory page to the first byte of the first page. The address “roll over” during write is from the last byte of the current page to the first byte of the same page. Once the device address with the read/write select bit set to “1” is clocked in and acknowledged by the EEPROM, the current address data word is serially clocked out. The microcontroller does not respond with an input “0” but does generate a following stop condition (see Figure 11-4 on page 11). RANDOM READ: A random read requires a “dummy” byte write sequence to load in the data word address. Once the device address word and data word address are clocked in and acknowledged by the EEPROM, the microcontroller must generate another start condition. The microcontroller now initiates a current address read by sending a device address with the read/write select bit high. The EEPROM acknowl edges the device address and serially clocks out the data word. The microcontroller does not respond with a “0” but does generate a following stop condition (see Figure 11-5 on page 11). SEQUENTIAL READ: Sequential reads are initiated by either a current address read or a ran- dom address read. After the microcontroller receives a data word, it responds with an acknowledge. As long as the EEPROM receives an acknowledge, it will continue to increment the data word address and serially clock out sequential data words. When the memory address limit is reached, the data word address will “roll over” and the sequential read will continue. The sequential read operation is terminated when the microcontroller does not respond with a “0” but does generate a following stop condition (see Figure 11-6 on page 12). Figure 11-1. Device Address MSB 1K/2K 1 0 1 0 A2 A1 A0 R/W 4K 1 0 1 0 A2 A1 P0 R/W 8K 1 0 1 0 A2 P1 P0 R/W

8517C–SEEPR–01/09 AT24C01B/02B/04B/08B Figure 11-6. Sequential Read

8517C–SEEPR–01/09 AT24C01B/02B/04B/08B Notes: 1. “-B” denotes bulk. 2. “-T” denotes tape and reel. SOIC = 4K per reel. TSSOP = 5K per reel. 12. AT24C01B Ordering Information Ordering Code Package Operation Range AT24C01BN-SP25-B(1) AT24C01BN-SP25-T(2) AT24C01B-TP25-B(1) AT24C01B-TP25-T(2) 8S1 8S1 8A2 8A2 Lead-free/Halogen-free/NiPdAu Lead Finish/Automotive Temperature (−40°C to 125°C) Package Type 8S1 8-lead, 0.150” Wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 8A2 8-lead, 4.4 mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) Options −2.5 Low-voltage (2.5V to 5.5V)

8517C–SEEPR–01/09 AT24C01B/02B/04B/08B 13. AT24C02B Ordering Information Notes: 1. “-B” denotes bulk. 2. “-T” denotes tape and reel. SOIC = 4K per reel. TSSOP = 5K per reel. Ordering Code Package Operation Range AT24C02BN-SP25-B(1) AT24C02BN-SP25-T(2) AT24C02B-TP25-B(1) AT24C02B-TP25-T(2) 8S1 8S1 8A2 8A2 Lead-free/Halogen-free/NiPdAu Lead Finish/Automotive Temperature (−40°C to 125°C) Package Type 8S1 8-lead, 0.150” Wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 8A2 8-lead, 4.4 mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) Options −2.5 Low-voltage (2.5V to 5.5V)

8517C–SEEPR–01/09 AT24C01B/02B/04B/08B Notes: 1. “-B” denotes bulk. 2. “-T” denotes tape and reel. SOIC = 4K per reel. TSSOP = 5K per reel. 14. AT24C04B Ordering Information Ordering Code Package Operation Range AT24C04BN-SP25-B(1) AT24C04BN-SP25-T(2) AT24C04B-TP25-B(1) AT24C04B-TP25-T(2) 8S1 8S1 8A2 8A2 Lead-free/Halogen-free/NiPdAu Lead Finish/Automotive Temperature (−40°C to 125°C) Package Type 8S1 8-lead, 0.150” Wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 8A2 8-lead, 4.4 mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) Options −2.5 Low-voltage (2.5V to 5.5V)

8517C–SEEPR–01/09 AT24C01B/02B/04B/08B Notes: 1. “-B” denotes bulk. 2. “-T” denotes tape and reel. SOIC = 4K per reel. TSSOP = 5K per reel. 15. AT24C08B Ordering Information Ordering Code Package Operation Range AT24C08BN-SP25-B(1) AT24C08BN-SP25-T(2) AT24C08B-TP25-B(1) AT24C08B-TP25-T(2) 8S1 8S1 8A2 8A2 Lead-free/Halogen-free/NiPdAu Lead Finish/Automotive Temperature (−40°C to 125°C) Package Type 8S1 8-lead, 0.150” Wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 8A2 8-lead, 4.4 mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) Options −2.5 Low-voltage (2.5V to 5.5V)

8517C–SEEPR–01/09 AT24C01B/02B/04B/08B 16. Packaging Information 16.1 8A2 – TSSOP

2325 Orchard Parkway

San Jose, CA 95131 TITLE DRAWING NO. R REV. 5/30/02 COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE D 2.90 3.00 3.10 2, 5 E 6.40 B SC E1 4. 30 4.40 4.50 3, 5 A – – 1.20 A2 0. 80 1.00 1.05 b 0.19 – 0. 30 4 e 0.65 B SC L 0.45 0.60 0.75 L1 1.00 REF 8A2, 8-lead, 4.4 mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) Notes: 1. Thi s drawing is for general information only. Refer to JEDEC Drawing MO-153, Variation AA, for proper dimensions, tolerances, d atums, etc. 2. Dimen sion D does not include mold Flash, protrusions or gate burrs. Mold Flash, protrusions and gate burrs shall not exceed 0.15 mm (0.006 in) per side. 3. Dimen sion E1 does not include inter-lead Flash or protrusions. Inter-lead Flash and protrusions shall not exceed 0.25 mm (0.010 in) per side. 4. Dimen sion b does not include Dambar protrusion. Allowable Dambar protrusion shall be 0.08 mm total in excess of the b dimension at maximum material condition. Dambar cannot be located on the lower radius of the foot. Minimum space between protr usion and adjacent lead is 0.07 mm. 5. Dimen sion D and E1 to be determined at Datum Plane H. 8A2 B Side View End ViewTop View A L D 123 N b Pin 1 indicator this corner E e

8517C–SEEPR–01/09 AT24C01B/02B/04B/08B 16.2 8S1 – JEDEC SOIC 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TITLE DRAWING NO. R REV. Note: 10/7/03 8S1, 8-lead (0.150" Wide Body), Plastic Gull Wing Small Outline (JEDEC SOIC) 8S1 B COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A1 0.10 – 0.25 These drawings are for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. A 1.35 – 1.75 b 0.31 – 0.51 C 0.17 – 0.25 D 4.80 – 5.00 E1 3.81 – 3.99 E 5.79 – 6.20 e 1.27 BSC L 0.40 – 1.27 ∅ 0˚ – 8˚ Top View End View Side View e B D A N E C L

8517C–SEEPR–01/09 AT24C01B/02B/04B/08B 17. Revision History Doc. Rev. Date Comments 8517C 1/2009 Removed Preliminary status. 8517B 3/2008 Added data for 8K device. 8517A 1/2008 Initial document release.

8517C–SEEPR–01/09 Headquarters International Atmel Corporation San Jose, CA 95131 USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Atmel Asia Room 1219 Chinachem Golden Plaza

77 Mody Road Tsimshatsui

Tel: (852) 2721-9778 Fax: (852) 2722-1369 Atmel Europe Le Krebs 8, Rue Jean-Pierre Timbaud BP 309

78054 Saint-Quentin-en-

9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Product Contact Web Site www.atmel.com Technical Support s_eeprom@atmel.com Sales Contact www.atmel.com/contacts Literature Requests www.atmel.com/literature Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL ’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL ’S WEB SITE, ATMEL ASSUMES NO LI ABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTOR Y WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICU LAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR I NCIDEN- TAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATME L HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or comp leteness of the contents of this document and reserves the rig ht to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained her ein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not int ended, authorized, or warranted for use as components in applications in tended to support or sustain life. © 2009 Atmel Corporation. All rights reserved. Atmel ®, Atmel logo and combinations thereof, and ot hers, are registered trademarks or trade- marks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.