AT17N256_07 ATMEL
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 18
Technical content
Features
- EE Programmable 262,144 x 1-, 524,288 x 1-, 1,048,576 x 1-, 2,097,152 x 1-, and 4,194,304 x 1-bit Serial Memories Designed to Store Configuration Programs for Field Programmable Gate Arrays (FPGAs) Available as a 3.3V (±10%) Commercial and Industrial Version Simple Interface to SRAM FPGAs Pin Compatible with Xilinx® XC17SXXXA and XC17SXXXXL PROMs Compatible with Xilinx Spartan®-II, Spartan-IIE and Spartan XL FPGAs in Master Serial Mode Very Low-power CMOS EEPROM Process Available in 8-lead PDIP, 8-lead SOIC, 20-lead SOIC and 44-lead TQFP Packages for a Specific Density Low-power Standby Mode High-reliability – Endurance: Minimum 10 Write Cycles – Data Retention: 20 Years at 85°C
Description
The AT17N series FPGA Configuration EEPROM (Configurators) provide an easy-to- use, cost-effective configuration memory for Field Programmable Gate Arrays. The AT17N series device is packaged in the 8-lead PDIP , 8-lead SOIC, 20-lead SOIC and 44-lead TQFP , see Table 1. The AT17N series Configurators uses a simple serial- access procedure to configure one or more FPGA devices. The AT17N series configurators can be programmed with industry-standard program- mers, Atmel’s ATDH2200E Programming Kit or Atmel’s ATDH2225 ISP Cable and factory programming. Table 1. AT17N Series Packages
2 AT17N256/512/010/002/040
3020C–CNFG–08/07 Pin Configuration 8-lead SOIC 8-lead PDIP 20-lead SOIC DATA CLK RESET/OE CE VCC VCC (SER_EN) DC GND DATA CLK RESET/OE CE VCC VCC (SER_EN) DC GND DATA NC CLK NC NC NC NC RESET/OE NC CE VCC NC VCC (SER_EN) NC NC NC NC DC NC GND
3020C–CNFG–08/07
44 TQFP
VCC (SER_EN) NC NC NC NC NC NC NC DC NC NC NC NC NC NC NC NC NC NC NC NC NC NC DC
4 AT17N256/512/010/002/040
3020C–CNFG–08/07 Block Diagram Device Description The control signals for th e configuration EEPROM (CE , RESET/OE and CCLK) inter- face directly with the FPGA device control signals. All FPGA devices can control the entire configuration process and retrieve data from the configuration EEPROM without requiring an external intelligent controller. The configuration EEPROM RESET/OE and CE pins control the tri-state buffer on the DATA output pin and enable the address counter. When RESET/OE is driven High, the configuration EEPROM resets its address counter and tri-states its DATA pin. The CE pin also controls the output of the AT17N series configurator. If CE is held High after the RESET/OE reset pulse, the counter is disabled and the DATA output pin is tri-stated. When OE is subsequently driven Low, the counter and the DATA output pin are enabled. When RESET/OE is driven High again, the address counter is reset and the DATA output pin is tri-stated, regardless of the state of CE. Upon power-up, the address counter is automatically reset. POWER ON RESET SER_EN
3020C–CNFG–08/07 DATA Three-state DATA output for configurati on. Open-collector bi-directional pin for programming. CLK Clock input. Used to increment the internal address and bit counter for reading and programming. RESET/OE Output Enable (active High) and RESET (active Low) when SER_EN is High. A Low level on RESET /OE resets both the address and bit counters. A High level (with CE Low) enables the data output driver. The logi c polarity of this input is programmable as either RESET/OE or RESET/OE. For most applications, RESET should be programmed active Low. This document describes the pin as RESET/OE. CE Chip Enable input (active Low). A Low level (with OE High) allows CLK to increment the address counter and enables the data output driver. A High level on CE disables both the address and bit counters and forces th e device into a low-power standby mode. Note that this pin will not enable/disable the device in the Two-Wire Serial Programming mode (SER_EN Low). GND Ground pin. A 0.2 µF decoupling capacitor between VCC and GND is recommended. VCC(SER_EN) Serial enable must be held High during FP GA loading operations. Bringing SER_EN Low enables the Two-Wire Serial Programming Mode. For non-ISP applications, SER_EN should be tied to VCC. VCC 3.3V (±10%) Commercial and Industrial power supply pin. NC NC pins are No Connect pins, which are not internally bonded out to the die. DC DC pins are No Connect pins internally c onnected to the die. It is not recommended to connect these pins to any external signal. Pin Description Name I/O AT17N256 AT17N512/ AT17N010 AT17N002 AT17N040 DIP/ SOIC SOIC DIP SOIC SOIC TQFP TQFP D A T A I / O 11111 4 0 4 0 C L K I 23233 4 3 4 3 RESET/OE I 38388 1 3 1 3 CE I 4 1 0 4 1 01 01 51 5 G N D 5 1 1 5 1 11 11 81 8 D C O 6 1 3 6 1 31 32 12 1 VCC(SER_EN) I 7 1 8 7 1 81 83 53 5 VCC 8 2 0 8 2 02 03 83 8
6 AT17N256/512/010/002/040
3020C–CNFG–08/07 FPGA Master Serial Mode Summary The I/O and logic functions of any SRAM-bas ed FPGA are established by a configura- tion program. The program is loaded either automatically upon power-up, or on command, depending on the state of the FPGA mode pins. In Master mode, the FPGA automatically loads the configuration progr am from an external memory. The AT17N Serial Configuration EEPROM has been des igned for compatibility with the Master Serial mode. This document discusses the master serial mode configuration of Atmel AT17N series configuration memories, pin compatible with Spartan-II, Spartan-IIE and Spartan XL OTP PROMs. Control of Configuration Most connections between the FPGA device and the AT17N Serial EEPROM are simple and self-explanatory. The DATA output of the AT17N series configurator drives DIN of the FPGA devices. The master FPGA CCLK output drives the CLK input of the AT17N series configurator. SER_EN must be connected to VCC (except during ISP). T h e C E and OE/Reset are driven by the FPGA to enable output data buffer of the EEPROM. Programming Mode The programming mode is entered by bringing SER_EN Low. In this mode the chip can be programmed by the Two-Wire serial bus. The programming is done at V CC supply only. Programming super voltages are generated inside the chip. Standby Mode The AT17N series configurators enter a low-power standby mode whenever CE is asserted High. In this mode, the AT17N256 configurator consumes less than 50 µA of current at 3.3V (100 µA for the AT17N512/010 and 200 µA for the AT17N002/040).
3020C–CNFG–08/07 Absolute Maximum Ratings* Maximum Ratings may cause permanent dam- age to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those listed under oper- ating conditions is not implied. Exposure to Abso- lute Maximum Rating conditions for extended periods of time may affect device reliability. Voltage on Any Pin CC +0.5V Operating Conditions Symbol Description 3.3V UnitsMin Max VCC Commercial Supply voltage relative to GND Industrial Supply voltage relative to GND -40°C to +85°C 3.0 3.6 V
8 AT17N256/512/010/002/040
3020C–CNFG–08/07 Notes: 1. AC test lead = 50 pF . 2. Float delays are measured with 5 pF AC loads. Transition is measured ± 200 mV from steady-state active levels. DC Characteristics VCC = 3.3V ± 10% Symbol Description AT17N256 AT17N512/ AT17N010 AT17N002/ AT17N040 UnitsMin Max Min Max Min Max VIH High-level Input Voltage 2.0 V CC 2.0 V CC 2.0 V CC V VIL Low-level Input Voltage 0 0.8 0 0.8 0 0.8 V VOH High-level Output Voltage (IOH = -2.5 mA) Commercial 2.4 2.4 2.4 V VOL Low-level Output Voltage VOH High-level Output Voltage (IOH = -2 mA) Industrial 2.4 2.4 2.4 V VOL Low-level Output Voltage ICCA Supply Current, Active Mode 5 5 5 mA IL Input or Output Leakage Current (VIN = VCC or GND) -10 10 -10 10 -10 10 µA ICCS Supply Current, Standby Mode Commercial 50 100 150 µA Industrial 100 100 150 µA AC Characteristics VCC = 3.3V ± 10% Symbol Description AT17N256 AT17N512/010/002/040 Units Commercial Industrial Commercial Industrial Min Max Min Max Min Max Min Max TOE (1) OE to Data Delay 50 55 50 55 ns TCE (1) CE to Data Delay 60 60 55 60 ns TCAC (1) CLK to Data Delay 75 80 55 60 ns TOH Data Hold from CE, OE, or CLK 0 0 0 0 ns TDF (2) CE or OE to Data Float Delay 55 55 50 50 ns TLC CLK Low Time 25 25 25 25 ns THC CLK High Time 25 25 25 25 ns TSCE CE Setup Time to CLK (to guarantee proper counting) 35 60 30 35 ns THCE CE Hold Time from CLK (to guarantee proper counting) 0000 n s THOE OE High Time (guarantees counter is reset) 25 25 25 25 ns FMAX Maximum Clock Frequency 10 10 15 10 MHz
3020C–CNFG–08/07 AC Characteristics CE RESET/OE CLK DATA TSCE TLC THC TCACTOE TCE TOH THOE TSCE THCE TDF TOH
10 AT17N256/512/010/002/040
3020C–CNFG–08/07 Notes: 1. For more information refer to the “Thermal Characteri stics of Atmel’s Packages”, available on the Atmel web site. 2. Airflow = 0 ft/min. Thermal Resistance Coefficients(1) AT17N512/ AT17N010 AT17N002 AT17N040 8P3 Plastic Dual Inline Package (PDIP) θJC [°C/W] 37 37 – – θJA °C/W 107 107 – – 8S1 Plastic Gull Wing Small Outline (SOIC) θJC [°C/W] 45 – – – θJA °C/W 150 – – – 20S2 Plastic Gull Wing Small Outline (SOIC) θJC [°C/W] – θJA °C/W 44A Thin Plastic Quad Flat Package (TQFP) θJC [°C/W] – – 17 17 θJA °C/W –– 6 2 6 2
Figure 1. Ordering Code
12 AT17N256/512/010/002/040
3020C–CNFG–08/07 Notes: 1. For the -10CC and -10CI packages, customers may migrate to AT17LVXXX-10CU.
Ordering Information
Memory Size Ordering Code Package Operation Range 256-Kbit AT17N256-10PC 8P3 Commercial (0°C to 70°C)AT17N256-10NC 8S1 AT17N256-10SC 20S2 AT17N256-10PI 8P3 Industrial (-40°C to 85°C)AT17N256-10NI 8S1 AT17N256-10SI 20S2 512-Kbit AT17N512-10SC 20S2 Commercial (0°C to 70°C) AT17N512-10SI 20S2 Industrial (-40°C to 85°C) 1-Mbit AT17N010-10SC 20S2 Commercial (0°C to 70°C) AT17N010-10SI 20S2 Industrial (-40°C to 85°C) 2-Mbit AT17N002-10SC 20S2 Commercial (0°C to 70°C)AT17N002-10TQC 44A AT17N002-10SI 20S2 Industrial (-40°C to 85°C)AT17N002-10TQI 44A 4-Mbit AT17N040-10TQC 44A Commercial (0°C to 70°C) AT17N040-10TQI 44A Industrial (-40°C to 85°C)
3020C–CNFG–08/07 Packaging Information 8P3 – PDIP
2325 Orchard Parkway
San Jose, CA 95131 TITLE DRAWING NO. R REV. 8P3, 8-lead, 0.300" Wide Body, Plastic Dual In-line Package (PDIP) 01/09/02 8P3 B D E e Lb2 b A2 A N eA c
4 PLCS
(Unit of Measure = inches) SYMBOL MIN NOM MAX NOTE Notes: 1. This drawing is for general information only; refer to JEDEC Drawing MS-001, Variation BA for additional information. 2. Dimensions A and L are measured with the package seated in JEDEC seating plane Gauge GS-3. 3. D, D1 and E1 dimensions do not include mold Flash or protrusions. Mold Flash or protrusions shall not exceed 0.010 inch. 4. E and eA measured with the leads constrained to be perpendicular to datum. 5. Pointed or rounded lead tips are preferred to ease insertion. A 0.210 2 A2 0.115 0.130 0.195 b 0.014 0.018 0.022 5 b2 0.045 0.060 0.070 6 b3 0.030 0.039 0.045 6 c 0.008 0.010 0.014 D 0.355 0.365 0.400 3 D1 0.005 3 E 0.300 0.310 0.325 4 E1 0.240 0.250 0.280 3 e 0.100 BSC eA 0.300 BSC 4 L 0.115 0.130 0.150 2
14 AT17N256/512/010/002/040
3020C–CNFG–08/07 8S1 – SOIC 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TITLE DRAWING NO. R REV. Note: 3/17/05 8S1, 8-lead (0.150" Wide Body), Plastic Gull Wing Small Outline (JEDEC SOIC) 8S1C COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A1 0.10 – 0.25 These drawings are for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. ØØ EE NN TOP VIEW CC E1E1 END VIEW AA bb LL A1A1 ee DD SIDE VIEW
3020C–CNFG–08/07 20S2 – SOIC
16 AT17N256/512/010/002/040
3020C–CNFG–08/07 44A – TQFP San Jose, CA 95131 TITLE DRAWING NO. R REV. 44A, 44-lead, 10 x 10 mm Body Size, 1.0 mm Body Thickness, 0.8 mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP) B44A 10/5/2001 PIN 1 IDENTIFIER 0˚~7˚ PIN 1 L C A1 A2 A D e E1 E B COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE Notes: 1. This package conforms to JEDEC reference MS-026, Variation ACB. 2. Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is 0.25 mm per side. Dimensions D1 and E1 are maximum plastic body size dimensions including mold mismatch. 3. Lead coplanarity is 0.10 mm maximum. A – – 1.20 A1 0.05 – 0.15 A2 0.95 1.00 1.05 D 11.75 12.00 12.25 D1 9.90 10.00 10.10 Note 2 E 11.75 12.00 12.25 E1 9.90 10.00 10.10 Note 2 B 0.30 – 0.45 C 0.09 – 0.20 L 0.45 – 0.75 e 0.80 TYP
3020C–CNFG–08/07
Revision History
Revision Level – Release Date History B – March 2006 Added last-time buy for AT17NXXX-10CC and AT17NXXX-10CI. C – August 2007 Removed 8CN4 8-lead LAP package.
3020C–CNFG–08/07 Headquarters International Atmel Corporation San Jose, CA 95131 USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Atmel Asia Room 1219 Chinachem Golden Plaza
77 Mody Road Tsimshatsui
Tel: (852) 2721-9778 Fax: (852) 2722-1369 Atmel Europe Le Krebs 8, Rue Jean-Pierre Timbaud BP 309
78054 Saint-Quentin-en-
9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Product Contact Web Site www.atmel.com Technical Support configurator@atmel.com Sales Contact www.atmel.com/contacts Literature Requests www.atmel.com/literature Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL ’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL ’S WEB SITE, ATMEL ASSUMES NO LI ABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTOR Y WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICU LAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR I NCIDEN- TAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATME L HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or comp leteness of the contents of this document and reserves the rig ht to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained her ein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not int ended, authorized, or warranted for use as components in applications in tended to support or sustain life. © Atmel Corporation 2007 . All rights reserved. Atmel ®, logo and combinations thereof, Everywhere Y ou Are ® and others are registered trade- marks or trademarks of Atmel Corporation or its subsidiaries. FLEX ™ is the trademark of Altera Corporation; ORCA ™ is the trademark of Lattice Semiconductors; SPARTAN ® and Virtex ® are the registered trademarks of Xilinx, Inc.; XC3000 ™ , XC4000 ™ and XC5200 ™ are the trademarks of Xilinx, Inc.; APEX ™ is the trademark of MIPS Technologies; Other terms and product names may be the trademarks of others.