AT17N256 ATMEL

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 18

Technical content

Features

  • EE Programmable 262,144 x 1-, 524,288 x 1-, 1,048,576 x 1-, 2,097,152 x 1-, and 4,194,304 x 1-bit Serial Memories Designed to Store Configuration Programs for Field Programmable Gate Arrays (FPGAs)  Available as a 3.3V (±10%) Commercial and Industrial Version  Simple Interface to SRAM FPGAs  Pin Compatible with Xilinx® XC17SXXXA and XC17SXXXXL PROMs  Compatible with Xilinx Spartan®-II, Spartan-IIE and Spartan XL FPGAs in Master Serial Mode  Very Low-power CMOS EEPROM Process  Available in 6 mm x 6 mm x 1 mm 8-lead LAP (Pin-compatible with 8-lead SOIC/VOIC Packages), 8-lead PDIP, 8-lead SOIC, 20-lead SOIC and 44-lead TQFP Packages for a Specific Density  Low-power Standby Mode  High-reliability – Endurance: Minimum 10 Write Cycles – Data Retention: 20 Years at 85°C

Description

The AT17N series FPGA Configuration EEPROM (Configurators) provide an easy-to- use, cost-effective configuration memory for Field Programmable Gate Arrays. The AT17N series device is packaged in the 8-lead LAP , 8-lead PDIP , 8-lead SOIC, 20-lead SOIC and 44-lead TQFP , see Table 1. The AT17N series Configurators uses a simple serial-access procedure to configure one or more FPGA devices. The AT17N series configurators can be programmed with industry-standard program- mers, Atmel’s ATDH2200E Programming Kit or Atmel’s ATDH2225 ISP Cable and factory programming. Note: 1. The 8-lead LAP package has the same footprint as the 8-lead SOIC. Since an 8- lead SOIC package is not available for the AT17N512/010/002 devices, it is possi- ble to use an 8-lead LAP package instead. Table 1. AT17N Series Packages

2 AT17N256/512/010/002/040

3020A–CNFG–04/10/03 Pin Configuration 8-lead LAP 8-lead SOIC 8-lead PDIP 20-lead SOIC DATA CLK RESET/OE CE VCC VCC (SER_EN) DC GND DATA CLK RESET/OE CE VCC VCC (SER_EN) DC GND DATA CLK RESET/OE CE VCC VCC (SER_EN) DC GND DATA NC CLK NC NC NC NC RESET/OE NC CE VCC NC VCC (SER_EN) NC NC NC NC DC NC GND

3020A–CNFG–04/10/03

44 TQFP

VCC (SER_EN)VCC (SER_EN) NCNC NC NC NC NC NC NC DC NC NC NC NC NC NC NC NC NC NC NC NC NC NC DC

4 AT17N256/512/010/002/040

3020A–CNFG–04/10/03 Block Diagram Device Description The control signals for the configuration EEPROM (CE , RESET/OE and CCLK) inter- face directly with the FPGA device control signals. All FPGA devices can control the entire configuration process and retrieve data from the configuration EEPROM without requiring an external intelligent controller. The configuration EEPROM RESET/OE and CE pins control the tri-state buffer on the DATA output pin and enable the address counter. When RESET/OE is driven High, the configuration EEPROM resets its address count er and tri-states its DATA pin. The CE pin also controls the output of the AT17N series configurator. If CE is held High after the RESET/OE reset pulse, the counter is disabled and the DATA output pin is tri-stated. When OE is subsequently driven Low, the counter and the DATA output pin are enabled. When RESET/OE is driven High again, the address counter is reset and the DATA output pin is tri-stated, regardless of the state of CE. Upon power-up, the address counter is automatically reset. POWER ON RESET SER_EN

3020A–CNFG–04/10/03 DATA Three-state DATA output for configuration. Open-collector bi-directional pin for programming. CLK Clock input. Used to increment the internal address and bit counter for reading and programming. RESET/OE Output Enable (active High) and RESET (active Low) when SER_EN is High. A Low level on RESET /OE resets both the address and bit counters. A High level (with CE Low) enables the data output driver. The logic polarity of this input is programmable as either RESET/OE or RESET/OE. For most applications, RESET should be programmed active Low. This document describes the pin as RESET/OE. CE Chip Enable input (active Low). A Low level (with OE High) allows CLK to increment the address counter and enables the data output driver. A High level on CE disables both the address and bit counters and forces the device into a low-power standby mode. Note that this pin will not enable/disable the device in the Two-Wire Serial Programming mode (SER_EN Low). GND Ground pin. A 0.2 µF decoupling capacitor between VCC and GND is recommended. VCC(SER_EN) Serial enable must be held High during FPGA loading operations. Bringing SER_EN Low enables the Two-Wire Serial Programming Mode. For non-ISP applications, SER_EN should be tied to VCC. VCC 3.3V (±10%) Commercial and Industrial power supply pin. NC NC pins are No Connect pins, which are not internally bonded out to the die. DC DC pins are No Connect pins internally connected to the die. It is not recommended to connect these pins to any external signal. Pin Description Name I/O AT17N256 AT17N512/ AT17N010 AT17N002 AT17N040 DIP/ SOIC SOIC DIP/ LAP SOIC LAP SOIC TQFP TQFP DATA I/O 1 1 1 1 1 1 40 40 C L KI 2 3 2323 4 3 4 3 RESET/OE I3 8 3 8 3 8 1 3 1 3 CE I 4 1 0 41 041 0 1 51 5 G N D 5 1 1 51 151 1 1 81 8 D C O 6 1 3 61 361 3 2 12 1 VCC(SER_EN) I 7 1 8 71 871 8 3 53 5 VCC 8 2 0 82 082 0 3 83 8

6 AT17N256/512/010/002/040

3020A–CNFG–04/10/03 FPGA Master Serial Mode Summary The I/O and logic functions of any SRAM-based FPGA are established by a configura- tion program. The program is loaded either automatically upon power-up, or on command, depending on the state of the FPGA mode pins. In Master mode, the FPGA automatically loads the configuration program from an external memory. The AT17N Serial Configuration EEPROM has been designed for compatibility with the Master Serial mode. This document discusses the master serial mode configuration of Atmel AT17N series configuration memories, pin compatible with Spartan-II, Spartan-IIE and Spartan XL OTP PROMs. Control of Configuration Most connections between the FPGA device and the AT17N Serial EEPROM are simple and self-explanatory.  The DATA output of the AT17N series configurator drives DIN of the FPGA devices.  The master FPGA CCLK output drives the CLK input of the AT17N series configurator.  SER_EN must be connected to VCC (except during ISP). T h e C E and OE/Reset are driven by the FPGA to enable output data buffer of the EEPROM. Programming Mode The programming mode is entered by bringing SER_EN Low. In this mode the chip can be programmed by the Two-Wire serial bus. The programming is done at V CC supply only. Programming super voltages are generated inside the chip. Standby Mode The AT17N series configurators enter a low-power standby mode whenever CE is asserted High. In this mode, the AT17N256 c onfigurator consumes less than 50 µA of current at 3.3V (100 µA for the AT17N512/010 and 200 µA for the AT17N002/040).

3020A–CNFG–04/10/03 Absolute Maximum Ratings* Maximum Ratings may cause permanent dam- age to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those listed under oper- ating conditions is not implied. Exposure to Abso- lute Maximum Rating conditions for extended periods of time may affect device reliability. Voltage on Any Pin CC +0.5V Operating Conditions Symbol Description 3.3V UnitsMin Max VCC Commercial Supply voltage relative to GND Industrial Supply voltage relative to GND -40°C to +85°C 3.0 3.6 V

8 AT17N256/512/010/002/040

3020A–CNFG–04/10/03 Notes: 1. AC test lead = 50 pF . 2. Float delays are measured with 5 pF AC loads. Transition is measured ± 200 mV from steady-state active levels. DC Characteristics VCC = 3.3V ± 10% Symbol Description AT17N256 AT17N512/ AT17N010 AT17N002/ AT17N040 UnitsMin Max Min Max Min Max VIH High-level Input Voltage 2.0 V CC 2.0 V CC 2.0 V CC V VIL Low-level Input Voltage 0 0.8 0 0.8 0 0.8 V VOH High-level Output Voltage (IOH = -2.5 mA) Commercial 2.4 2.4 2.4 V VOL Low-level Output Voltage VOH High-level Output Voltage (IOH = -2 mA) Industrial 2.4 2.4 2.4 V VOL Low-level Output Voltage ICCA Supply Current, Active Mode 5 5 5 mA IL Input or Output Leakage Current (VIN = VCC o r G N D ) - 1 01 0- 1 01 0- 1 01 0µ A ICCS Supply Current, Standby Mode Commercial 50 100 150 µA Industrial 100 100 150 µA AC Characteristics VCC = 3.3V ± 10% Symbol Description AT17N256 AT17N512/010/002/040 Units Commercial Industrial Commercial Industrial Min Max Min Max Min Max Min Max TOE (1) OE to Data Delay 50 55 50 55 ns TCE (1) CE to Data Delay 60 60 55 60 ns TCAC (1) CLK to Data Delay 75 80 55 60 ns TOH Data Hold from CE, O E , o r C L K 0000 n s TDF (2) CE or OE to Data Float Delay 55 55 50 50 ns TLC CLK Low Time 25 25 25 25 ns THC CLK High Time 25 25 25 25 ns TSCE CE Setup Time to CLK (to guarantee proper counting) 35 60 30 35 ns THCE CE Hold Time from CLK (to guarantee proper counting) 0000 n s THOE OE High Time (guarantees counter is reset) 25 25 25 25 ns FMAX Maximum Clock Frequency 10 10 15 10 MHz

3020A–CNFG–04/10/03 AC Characteristics CE RESET/OE CLK DATA TSCE TLC THC TCACTOE TCE TOH THOE TSCE THCE TDF TOH

10 AT17N256/512/010/002/040

3020A–CNFG–04/10/03 Notes: 1. For more information refer to the “Thermal Characteristics of Atmel’s Packages”, available on the Atmel web site. 2. Airflow = 0 ft/min. Thermal Resistance Coefficients(1) AT17N512/ AT17N010 AT17N002 AT17N040 8CN4 Leadless Array Package (LAP) θJC [°C/W] – 45 45 – θJA °C/W – 135.71 159.60 – 8P3 Plastic Dual Inline Package (PDIP) θJC [°C/W] 37 37 – – θJA °C/W 107 107 – – 8S1 Plastic Gull Wing Small Outline (SOIC) θJC [°C/W] 45 – – – θJA °C/W 150 – – – 20S2 Plastic Gull Wing Small Outline (SOIC) θJC [°C/W] – θJA °C/W 44A Thin Plastic Quad Flat Package (TQFP) θJC [°C/W] – – 17 17 θJA °C/W –– 6 2 6 2

Figure 1. Ordering Code

12 AT17N256/512/010/002/040

3020A–CNFG–04/10/03

Ordering Information

Memory Size Ordering Code Package Operation Range 256-Kbit AT17N256-10PC AT17N256-10NC AT17N256-10SC 8P3 8S1 20S2 Commercial (0°C to 70°C) AT17N256-10PI AT17N256-10NI AT17N256-10SI 8P3 8S1 20S2 Industrial (-40°C to 85°C) 512-Kbit AT17N512-10CC AT17N512-10PC AT17N512-10SC 8CN4 8P3 20S2 Commercial (0°C to 70°C) AT17N512-10CI AT17N512-10PI AT17N512-10SI 8CN4 8P3 20S2 Industrial (-40°C to 85°C) 1-Mbit AT17N010-10CC AT17N010-10PC AT17N010-10SC 8CN4 8P3 20S2 Commercial (0°C to 70°C) AT17N010-10CI AT17N010-10PI AT17N010-10SI 8CN4 8P3 20S2 Industrial (-40°C to 85°C) 2-Mbit AT17N002-10CC AT17N002-10SC AT17N002-10TQC 8CN4 20S2 44A Commercial (0°C to 70°C) AT17N002-10CI AT17N002-10SI AT17N002-10TQI 8CN4 20S2 44A Industrial (-40°C to 85°C) 4-Mbit AT17N040-10TQC 44A Commercial (0°C to 70°C) AT17N040-10TQI 44A Industrial (-40°C to 85°C)

3020A–CNFG–04/10/03 Packaging Information 8CN4 – LAP

2325 Orchard Parkway

San Jose, CA 95131 TITLE DRAWING NO. R REV. 8CN4, 8-lead (6 x 6 x 1.04 mm Body), Lead Pitch 1.27 mm, Leadless Array Package (LAP) A8CN4 11/14/01 Pin1 Corner Marked Pin1 Indentifier 0.10 mm TYP Top View L b e Side View A Bottom View E D COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A 0.94 1.04 1.14 A1 0.30 0.34 0.38 b 0.45 0.50 0.55 1 D 5.89 5.99 6.09 E 4.89 5.99 6.09 e 1.27 BSC e1 1.10 REF L 0.95 1.00 1.05 1 L1 1.25 1.30 1.35 1 Note: 1. Metal Pad Dimensions.

14 AT17N256/512/010/002/040

3020A–CNFG–04/10/03 8P3 – PDIP San Jose, CA 95131 TITLE DRAWING NO. R REV. 8P3, 8-lead, 0.300" Wide Body, Plastic Dual In-line Package (PDIP) 01/09/02 8P3 B D E e Lb2 b A2 A N eA c

4 PLCS

(Unit of Measure = inches) SYMBOL MIN NOM MAX NOTE Notes: 1. This drawing is for general information only; refer to JEDEC Drawing MS-001, Variation BA for additional information. 2. Dimensions A and L are measured with the package seated in JEDEC seating plane Gauge GS-3. 3. D, D1 and E1 dimensions do not include mold Flash or protrusions. Mold Flash or protrusions shall not exceed 0.010 inch. 4. E and eA measured with the leads constrained to be perpendicular to datum. 5. Pointed or rounded lead tips are preferred to ease insertion. A 0.210 2 A2 0.115 0.130 0.195 b 0.014 0.018 0.022 5 b2 0.045 0.060 0.070 6 b3 0.030 0.039 0.045 6 c 0.008 0.010 0.014 D 0.355 0.365 0.400 3 D1 0.005 3 E 0.300 0.310 0.325 4 E1 0.240 0.250 0.280 3 e 0.100 BSC eA 0.300 BSC 4 L 0.115 0.130 0.150 2

3020A–CNFG–04/10/03 8S1 – SOIC San Jose, CA 95131 TITLE DRAWING NO. R REV. Note: 10/10/01 8S1, 8-lead (0.150" Wide Body), Plastic Gull Wing Small Outline (JEDEC SOIC) 8S1 A H N Top View C E End View A B L e D Side View COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE This drawing is for general information only. Refer to JEDEC Drawing MS-012 for proper dimensions, tolerances, datums, etc. A – – 1.75 B – – 0.51 C – – 0.25 D – – 5.00 E – – 4.00 e 1.27 BSC H – – 6.20 L – – 1.27

16 AT17N256/512/010/002/040

3020A–CNFG–04/10/03 20S2 – SOIC San Jose, CA 95131 TITLE DRAWING NO. R REV. 20S2, 20-lead, 0.300" Wide Body, Plastic Gull Wing Small Outline Package (SOIC) 1/9/02 20S2 A L End View Side View Top View HE b N e A D C COMMON DIMENSIONS (Unit of Measure = inches) SYMBOL MIN NOM MAX NOTE Notes: 1. This drawing is for general information only; refer to JEDEC Drawing MS-013, Variation AC for additional information. 2. Dimension "D" does not include mold Flash, protrusions or gate burrs. Mold Flash, protrusions and gate burrs shall not exceed 0.15 mm (0.006") per side. 3. Dimension "E" does not include inter-lead Flash or protrusion. Inter-lead Flash and protrusions shall not exceed 0.25 mm (0.010") per side. 4. "L" is the length of the terminal for soldering to a substrate. 5. The lead width "b", as measured 0.36 mm (0.014") or greater above the seating plane, shall not exceed a maximum value of 0.61 mm (0.024") per side. A 0.0926 0.1043 A1 0.0040 0.0118 b 0.0130 0.0200 4 C 0.0091 0.0125 D 0.4961 0.5118 1 E 0.2914 0.2992 2 H 0.3940 0.4190 L 0.0160 0.050 3 e 0.050 BSC

3020A–CNFG–04/10/03 44A – TQFP San Jose, CA 95131 TITLE DRAWING NO. R REV. 44A, 44-lead, 10 x 10 mm Body Size, 1.0 mm Body Thickness, 0.8 mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP) B44A 10/5/2001 PIN 1 IDENTIFIER 0˚~7˚ PIN 1 L C A1 A2 A D e E1 E B COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE Notes: 1. This package conforms to JEDEC reference MS-026, Variation ACB. 2. Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is 0.25 mm per side. Dimensions D1 and E1 are maximum plastic body size dimensions including mold mismatch. 3. Lead coplanarity is 0.10 mm maximum. A – – 1.20 A1 0.05 – 0.15 A2 0.95 1.00 1.05 D 11.75 12.00 12.25 D1 9.90 10.00 10.10 Note 2 E 11.75 12.00 12.25 E1 9.90 10.00 10.10 Note 2 B 0.30 – 0.45 C 0.09 – 0.20 L 0.45 – 0.75 e 0.80 TYP

Printed on recycled paper. 3020A–CNFG–04/10/03 xM Disclaimer: Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company’s standar d warranty which is detailed in Atmel’s Terms and Conditions located on the Company’s web site. The Company assumes no responsibi lity for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time wi thout notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Atmel are granted by the Company in connection with the sale of Atmel products , expressly or by implication. Atmel’s products are not aut horized for use as critical components in life support devices or systems. Atmel Corporation Atmel Operations San Jose, CA 95131 Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Regional Headquarters Europe Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland Tel: (41) 26-426-5555 Fax: (41) 26-426-5500 Asia Room 1219 Chinachem Golden Plaza

77 Mody Road Tsimshatsui

Tel: (852) 2721-9778 Fax: (852) 2722-1369 Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Memory San Jose, CA 95131 Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 Microcontrollers San Jose, CA 95131 Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 La Chantrerie BP 70602

44306 Nantes Cedex 3, France

13106 Rousset Cedex, France

1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland Tel: (44) 1355-803-000 Fax: (44) 1355-242-743 RF/Automotive Theresienstrasse 2 Postfach 3535

74025 Heilbronn, Germany

1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom Avenue de Rochepleine BP 123

38521 Saint-Egreve Cedex, France

Atmel Programmable SLI Hotline (408) 436-4119 Atmel Programmable SLI e-mail configurator@atmel.com FAQ Available on web site e-mail literature@atmel.com Web Site http://www.atmel.com © Atmel Corporation 2003 . All rights reserved. Atmel ® and combinations thereof is the registered trademark of Atmel. FLEX ™ is the trademark of Altera Corporation; ORCA ™ is the trademark of Lattice Semiconductors; SPARTAN® and Virtex ® are the registered trademarks of Xilinx, Inc.; XC3000 ™ , XC4000 ™ and XC5200 ™ are the trademarks of Xilinx, Inc.; APEX ™ is the trademark of MIPS Technologies; Other terms and product names may be the trademarks of others.