AT17LV65_08 ATMEL
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 26
Technical content
Features
- EE Programmable 65,536 x 1-, 131,072 x 1-, 262,144 x 1-, 524,288 x 1-, 1,048,576 x 1-, 2,097,152 x 1-, and 4,194,304 x 1-bit Serial Memories Designed to Store Configuration Programs for Field Programmable Gate Arrays (FPGAs) Supports both 3.3V and 5.0V Operating Voltage Applications In-System Programmable (ISP) via Two-Wire Bus Simple Interface to SRAM FPGAs Compatible with Atmel AT6000, AT40K and AT94K Devices, Altera® FLEX®, APEX™ Devices, ORCA®, Xilinx® XC3000, XC4000, XC5200, Spartan®, Virtex® FPGAs Cascadable Read-back to Support Additional Configurations or Higher-density Arrays Very Low-power CMOS EEPROM Process Programmable Reset Polarity Available in 6 mm x 6 mm x 1 mm 8-lead LAP (Pin-compatible with 8-lead SOIC/VOIC Packages), 8-lead PDIP, 8-lead SOIC, 20-lead PLCC, 20-lead SOIC and 44-lead TQFP Packages Emulation of Atmel’s AT24CXXX Serial EEPROMs Low-power Standby Mode High-reliability – Endurance: 100,000 Write Cycles – Data Retention: 90 Years for Industrial Parts (at 85° C) and 190 Years for Commercial Parts (at 70° C) Green (Pb/Halide-free/RoHS Compliant) Package Options Available 1. Description The AT17LV series FPGA Configuration EE PROMs (Configurators) provide an easy- to-use, cost-effective configuration memory for Field Programmable Gate Arrays. The AT17LV series device is packaged in the 8-lead LAP, 8-lead PDIP, 8-lead SOIC, 20- lead PLCC, 20-lead SOIC and 44-lead TQFP, see Table 1-1 . The AT17LV series Configurators uses a simple serial-access procedure to configure one or more FPGA devices. The user can select the polarity of the reset function by programming four EEPROM bytes. These devices also support a write-protection mechanism within its programming mode. The AT17LV series configurators can be programmed with industry-standard pro- grammers, Atmel’s ATDH2200E Programming Kit or Atmel’s ATDH2225 ISP Cable. FPGA Configuration EEPROM Memory AT17LV65 AT17LV128 AT17LV256 AT17LV512 AT17LV010 AT17LV002 AT17LV040 3.3V and 5V System Support 2321I–CNFG–2/08
2321I–CNFG–2/08 AT17LV65/128/256/512/010/002/040 Figure 2-8. Block Diagram Notes: 1. This pin is only availa ble on AT17LV65/128/256 devices. 2. This pin is only available on AT17LV512/010/002 devices. 3. The CEO feature is not available on the AT17LV65 device. POWER ON RESET SER_EN WP1 (2) WP2 (2) (1)READY (2)
2321I–CNFG–2/08 AT17LV65/128/256/512/010/002/040 3. Device Description The control signals for the configuration EEPROM (CE, RESET/OE and CCLK) interface directly with the FPGA device control signals. All FPGA devices can control the entire configuration pro- cess and retrieve data from the configurati on EEPROM without requiring an external intelligent controller. The configuration EEPROM RESET/OE and CE pins control the tri-state buffer on the DATA output pin and enable the addr ess counter. When RESET/OE is driven High, the configuration EEPROM resets its address counter and tri-states its DATA pin. The CE pin also controls the output of the AT17LV series configurator. If CE is held High after the RESET/OE reset pulse, the counter is disabled and the DATA output pin is tri-stated. When OE is subsequently driven Low, the counter and the DATA output pin are enabled. When RESET/OE is driven High again, the address counter is reset and the DATA output pin is tri-stated, regardless of the state of CE. When the configurator has driven out all of its data and CEO is driven Low, the device tri-states the DATA pin to avoid contention with other configurators. Upon power-up, the address counter is automatically reset. This is the default setting for the device. Since almost all FPGAs use RESET Low and OE High, this document will describe RESET/OE. Note: 1. The CEO feature is not available on the AT17LV65 device. 4. Pin Description Name I/O AT17LV65/ AT17LV128/ AT17LV256 AT17LV512/ AT17LV010 AT17LV002 AT17LV040 DIP/ LAP/ SOIC PLCC SOIC DIP/ LAP PLCC SOIC DIP/ LAP/ SOIC PLCC SOIC TQFP TQFP D A T A I / O 122121121 4 0 4 0 C L K I 244243243 4 3 4 3 RESET/ O E I 366368368 1 3 1 3 CE I 48848 1 0 48 1 0 1 5 1 5 G N D 51 0 1 051 0 1 151 0 1 1 1 8 1 8 CEO O 61 4 1 461 4 61 4 21 21 A2 I – – R E A D Y O –––– 1 5 –– 1 5 – 2 3 2 3 SER_EN I 71 7 1 771 7 1 871 7 1 8 3 5 3 5 VCC 82 0 2 082 0 2 082 0 2 0 3 8 3 8
2321I–CNFG–2/08 AT17LV65/128/256/512/010/002/040
4.1 DATA
Three-state DATA output for configuration. Open-collector bi-directional pin for programming.
4.2 CLK
Clock input. Used to increment the intern al address and bit c ounter for reading and programming.
4.3 WP1
WRITE PROTECT (1). Used to protect porti ons of memory during programming. Disabled by default due to internal pull-down resistor. Th is input pin is not used during FPGA loading operations. This pin is only available on AT17LV512/010/002 devices.
4.4 RESET/OE
Output Enable (active High) and RESET (active Low) when SER_EN is High. A Low level on RESET/OE resets both the address and bit counters. A High level (with CE Low) enables the data output driver. The logic polarity of this input is programmable as either RESET/OE or RESET/OE. For most applications, RESET should be programmed active Low. This document describes the pin as RESET/OE. 4.5 WP Write protect (WP) input (when CE is Low) during programming only (SER_EN Low). When WP is Low, the entire memory can be written. When WP is enabled (High), the lowest block of the memory cannot be written. This pin is only available on AT17LV65/128/256 devices.
4.6 WP2
WRITE PROTECT (2). Used to protect porti ons of memory during programming. Disabled by default due to internal pull-down resistor. Th is input pin is not used during FPGA loading operations. This pin is only available on AT17LV512/010 devices. 4.7 CE Chip Enable input (active Low). A Low level (with OE High) allows CLK to increment the address counter and enables the data output driver. A High level on CE disables both the address and bit counters and forces the device into a low-powe r standby mode. Note that this pin will not enable/disable the device in the Two-Wire Serial Programming mode (SER_EN Low).
4.8 GND
Ground pin. A 0.2 µF decoupling capacitor between VCC and GND is recommended.
4.9 CEO
Chip Enable Output (active Low). This output goes Low when the address counter has reached its maximum value. In a daisy chain of AT17LV series devices, the CEO pin of one device must be connected to the CE input of the next device in the chai n. It will stay Low as long as CE is Low and OE is High. It will then follow CE until OE goes Low; thereafter, CEO will stay High until the entire EEPROM is read again. This CEO feature is not available on the AT17LV65 device.
2321I–CNFG–2/08 AT17LV65/128/256/512/010/002/040 4.10 A2 Device selection input, A2. This is used to enable (or select) the device during programming (i.e., when SER_EN is Low). A2 has an internal pull-down resistor.
4.11 READY
Open collector reset state indicator. Driven Low during power-up reset, released when power-up is complete. It is recommended to use a 4.7 kΩ pull-up resistor when this pin is used.
4.12 SER_EN
Serial enable must be held High during FP GA loading operations. Bringing SER_EN Low enables the Two-Wire Serial Programming Mode. For non-ISP applications, SER_EN should be tied to VCC.
4.13 V CC
3.3V (±10%) and 5.0V (±5% Commercial, ±10% Industrial) power supply pin. 5. FPGA Master Serial Mode Summary The I/O and logic functions of any SRAM-based FPGA are established by a configuration pro- gram. The program is loaded either automatical ly upon power-up, or on command, depending on the state of the FPGA mode pins. In Master mode, the FPGA automatically loads the config- uration program from an external memory. The AT17LV Serial Configuration EEPROM has been designed for compatibility with the Master Serial mode. This document discusses the Atmel AT40K, AT40KAL and AT94KAL applications as well as Xil- inx applications. 6. Control of Configuration Most connections between the FPGA device and the AT17LV Serial EEPROM are simple and self-explanatory. The DATA output of the AT17LV series configurator drives DIN of the FPGA devices. The master FPGA CCLK output drives the CLK input of the AT17LV series configurator. The CEO output of any AT17LV series configurator drives the CE input of the next configurator in a cascaded chain of EEPROMs. S E R _ E N must be connected to VCC (except during ISP). The READY(1) pin is available as an open-collector indicator of the device’s reset status; it is driven Low while the device is in its power-on reset cycle and released (tri-stated) when the cycle is complete. Note: 1. This pin is not available for the AT17LV65/128/256 devices.
2321I–CNFG–2/08 AT17LV65/128/256/512/010/002/040 7. Cascading Serial Configuration EEPROMs For multiple FPGAs configured as a daisy-chain, or for FPGAs requiring larger configuration memories, cascaded configurators provide additional memory. After the last bit from the first configurator is read, the clock signal to the configurator asserts its CEO output Low and disables its DATA line driver. The second configurator recognizes the Low level on its CE input and enables its DATA output. After configuration is complete, the address coun ters of all cascaded configurators are reset if the RESET/OE on each configurator is driven to its active (Low) level. If the address counters are not to be reset upon completion, then the RESET /OE input can be tied to its inactive (High) level. The AT17LV65 devices do not have the CEO feature to perform cascaded configurations. 8. AT17LV Series Reset Polarity The AT17LV series configurator allows the us er to program the reset polarity as either RESET/OE or RESET /OE. This feature is supported by industry-standard programmer algorithms. 9. Programming Mode The programming mode is entered by bringing SER_EN Low. In this mode the chip can be pro- grammed by the Two-Wire serial bus. The programming is done at V CC supply only. Programming super voltages are generated inside the chip. 10. Standby Mode The AT17LV series configurators enter a low-power standby mode whenever CE is asserted High. In this mode, the AT17LV65/128/256 configurator consumes less than 50 µA of current at 3.3V (100 µA for the AT17LV512/010 and 200 µA for the AT17LV002/040). The output remains in a high-impedance state regardless of the state of the OE input.
2321I–CNFG–2/08 AT17LV65/128/256/512/010/002/040 11. Absolute Maximum Ratings* Maximum Ratings may cause permanent dam- age to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those listed under oper- ating conditions is not implied. Exposure to Abso- lute Maximum Rating conditions for extended periods of time may affect device reliability. Voltage on Any Pin CC +0.5V 12. Operating Conditions Symbol Description 3.3V 5V UnitsMin Max Min Max VCC Commercial Supply voltage relative to GND -0° C to +70° C 3.0 3.6 4.75 5.25 V Industrial Supply voltage relative to GND -40° C to +85° C 3.0 3.6 4.5 5.5 V
2321I–CNFG–2/08 AT17LV65/128/256/512/010/002/040 13. DC Characteristics VCC = 3.3V ± 10% Symbol Description AT17LV65/ AT17LV128/ AT17LV256 AT17LV512/ AT17LV010 AT17LV002/ AT17LV040 UnitsMin Max Min Max Min Max VIH High-level Input Voltage 2.0 V CC 2.0 V CC 2.0 V CC V VIL Low-level Input Voltage 0 0.8 0 0.8 0 0.8 V VOH High-level Output Voltage (IOH = -2.5 mA) Commercial 2.4 2.4 2.4 V VOL Low-level Output Voltage (IOL = +3 mA) 0.4 0.4 0.4 V VOH High-level Output Voltage (IOH = -2 mA) Industrial 2.4 2.4 2.4 V VOL Low-level Output Voltage (IOL = +3 mA) 0.4 0.4 0.4 V ICCA Supply Current, Active Mode 5 5 5 mA IL Input or Output Leakage Current (VIN = VCC or GND) -10 10 -10 10 -10 10 µA ICCS Supply Current, Standby Mode Commercial 50 100 150 µA Industrial 100 100 150 µA 14. DC Characteristics VCC = 5V ± 5% Commercial; VCC = 5V ± 10% Industrial Symbol Description AT17LV65/ AT17LV128/ AT17LV256 AT17LV512/ AT17LV010 AT17LV002/ AT17LV040 UnitsMin Max Min Max Min Max VIH High-level Input Voltage 2.0 V CC 2.0 V CC 2.0 V CC V VIL Low-level Input Voltage 0 0.8 0 0.8 0 0.8 V VOH High-level Output Voltage (IOH = -2.5 mA) Commercial 3.7 3.86 3.86 V VOL Low-level Output Voltage (IOL = +3 mA) 0.32 0.32 0.32 V VOH High-level Output Voltage (IOH = -2 mA) Industrial 3.6 3.76 3.76 V VOL Low-level Output Voltage (IOL = +3 mA) 0.37 0.37 0.37 V ICCA Supply Current, Active Mode 10 10 10 mA IL Input or Output Leakage Current (VIN = VCC or GND) -10 10 -10 10 -10 10 µA ICCS Supply Current, Standby Mode Commercial 75 200 350 µA Industrial 150 200 350 µA
2321I–CNFG–2/08 AT17LV65/128/256/512/010/002/040 15. AC Waveforms 16. AC Waveforms when Cascading CE RESET/OE CLK DATA TSCE TLC THC TCACTOE TCE TOH THOE TSCE THCE TDF TOH CE RESET/OE CLK DATA CEO TCDF TOCK TOCE TOCE TOOE LAST BIT FIRST BIT
2321I–CNFG–2/08 AT17LV65/128/256/512/010/002/040 Notes: 1. AC test lead = 50 pF . 2. Float delays are measured with 5 pF AC loads. Transition is measured ± 200 mV from steady-state active levels. Notes: 1. AC test lead = 50 pF . 2. Float delays are measured with 5 pF AC loads. Transition is measured ± 200 mV from steady-state active levels. 17. AC Characteristics VCC = 3.3V ± 10% Symbol Description AT17LV65/128/256 AT17LV512/010/002/040 Units Commercial Industrial Commercial Industrial Min Max Min Max Min Max Min Max TOE (1) OE to Data Delay 50 55 50 55 ns TCE (1) CE to Data Delay 60 60 55 60 ns TCAC (1) CLK to Data Delay 75 80 55 60 ns TOH Data Hold from CE, OE, or CLK 0 0 0 0 ns TDF (2) CE or OE to Data Float Delay 55 55 50 50 ns TLC CLK Low Time 25 25 25 25 ns THC CLK High Time 25 25 25 25 ns TSCE CE Setup Time to CLK (to guarantee proper counting) 35 60 30 35 ns THCE CE Hold Time from CLK (to guarantee proper counting) 0000 n s THOE OE High Time (guarantees counter is reset) 25 25 25 25 ns FMAX Maximum Clock Frequency 10 10 15 10 MHz 18. AC Characteristics when Cascading VCC = 3.3V ± 10% Symbol Description AT17LV65/128/256 AT17LV512/010/002/040 Units Commercial Industrial Commercial Industrial Min Max Min Max Min Max Min Max TCDF (2) CLK to Data Float Delay 60 60 50 50 ns TOCK (1) CLK to CEO D e l a y 5 56 05 05 5 n s TOCE (1) CE to CEO D e l a y 5 56 03 54 0 n s TOOE (1) RESET/OE to CEO D e l a y 4 04 53 53 5 n s FMAX Maximum Clock Frequency 8 8 12.5 10 MHz
2321I–CNFG–2/08 AT17LV65/128/256/512/010/002/040 Notes: 1. AC test lead = 50 pF . 2. Float delays are measured with 5 pF AC loads. Transition is measured ± 200 mV from steady-state active levels. Notes: 1. AC test lead = 50 pF . 2. Float delays are measured with 5 pF AC loads. Transition is measured ± 200 mV from steady-state active levels. 19. AC Characteristics VCC = 5V ± 5% Commercial; VCC = 5V ± 10% Industrial Symbol Description AT17LV65/128/256 AT17LV512/010/002/040 Units Commercial Industrial Commercial Industrial Min Max Min Max Min Max Min Max TOE (1) OE to Data Delay 30 35 30 35 ns TCE (1) CE to Data Delay 45 45 45 45 ns TCAC (1) CLK to Data Delay 50 55 50 50 ns TOH Data Hold from CE, OE, or CLK 0 0 0 0 ns TDF (2) CE or OE to Data Float Delay 50 50 50 50 ns TLC CLK Low Time 20 20 20 20 ns THC CLK High Time 20 20 20 20 ns TSCE CE Setup Time to CLK (to guarantee proper counting) 35 40 20 25 ns THCE CE Hold Time from CLK (to guarantee proper counting) 0000 n s THOE OE High Time (guarantees counter is reset) 20 20 20 20 ns FMAX Maximum Clock Frequency 12.5 12.5 15 15 MHz 20. AC Characteristics when Cascading VCC = 5V ± 5% Commercial; VCC = 5V ± 10% Industrial Symbol Description AT17LV65/128/256 AT17LV512/010/002/040 Units Commercial Industrial Commercial Industrial Min Max Min Max Min Max Min Max TCDF (2) CLK to Data Float Delay 50 50 50 50 ns TOCK (1) CLK to CEO D e l a y 3 54 03 54 0 n s TOCE (1) CE to CEO Delay 35 35 35 35 ns TOOE (1) RESET/OE to CEO Delay 30 35 30 30 ns FMAX Maximum Clock Frequency 10 10 12.5 12.5 MHz
2321I–CNFG–2/08 AT17LV65/128/256/512/010/002/040 Notes: 1. For more information refer to the “Thermal Characteri stics of Atmel’s Packages”, available on the Atmel web site. 2. Airflow = 0 ft/min. 21. Thermal Resistance Coefficients (1) Package Type AT17LV65/ AT17LV128/ AT17LV256 AT17LV512/ AT17LV010 AT17LV002 AT17LV040 8CN
4 Leadless Array Package (LAP)
θJC [° C/W] 45 45 45 – θJA 8P3 Plastic Dual Inline Package (PDIP) θJA 8S1 Plastic Gull Wing Small Outline (SOIC) θJA 20J Plastic Leaded Chip Carrier (PLCC) θJC [° C/W] 35 35 35 – θJA 20S2 Plastic Gull Wing Small Outline (SOIC) θJC [° C/W] – θJA ° C/W – 44A Thin Plastic Quad Flat Package (TQFP) θJA
2321I–CNFG–2/08 AT17LV65/128/256/512/010/002/040 Figure 21-1. Ordering Code Package Type 8CN4 8-lead, 6 mm x 6 mm x 1 mm, Leadless Array Package (LAP) – Pin-compatible with 8-lead SOIC/VOID Packages 8P3 8-lead, 0.300" Wide, Plastic Dual Inline Package (PDIP) 8S1 8-lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 20J 20-lead, Plastic J-leaded Chip Carrier (PLCC) 20S2 20-lead, 0.300" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 44A 44-lead, Thin (1.0 mm) Plastic Quad Flat Package Carrier (TQFP) Vo l t a g e Size (Bits) Special Pinouts Package Te mperature 65 = 65K A = Altera 8CN4 C = Commercial 128 = 128K Blank = Xilinx/Atmel/ = 8P3 I = Industrial 256 = 256K = 8S1 512 = 512K = 20J 010 = 1M = 44A002 = 2M = 44J040 = 4M AT17LV65A-10PC C P N J S TQ BJ =3.0V to 5.5V Other = 20S2 U = Fully Green
2321I–CNFG–2/08 AT17LV65/128/256/512/010/002/040 22. Ordering Information Notes: 1. For operating 5V operating voltage, please re fer to the corresponding AC and DC Characteristics. 2. For the -10SC and -10SI packages, cust omers may migrate to the AT17LVXXX-10SU. 3. For the -10TQC and -10TQI packages, cust omers may migrate to the AT17LVXXX-10TQU.
22.1 Standard Package Options
Memory Size Ordering Code Package (2)(3) Operation Range 64-Kbit(1) AT17LV65-10PC 8P3 Commercial (0° C to 70° C)AT17LV65-10NC 8S1 AT17LV65-10JC 20J AT17LV65-10PI 8P3 Industrial (-40° C to 85° C)AT17LV65-10NI 8S1 AT17LV65-10JI 20J 128-Kbit(1) AT17LV128-10PC 8P3 Commercial (0° C to 70° C) AT17LV128-10NC 8S1 AT17LV128-10JC 20J AT17LV128-10SC 20S2 AT17LV128-10PI 8P3 Industrial (-40° C to 85° C) AT17LV128-10NI 8S1 AT17LV128-10JI 20J AT17LV128-10SI 20S2 256-Kbit(1) AT17LV256-10PC 8P3 Commercial (0° C to 70° C) AT17LV256-10NC 8S1 AT17LV256-10JC 20J AT17LV256-10SC 20S2 AT17LV256-10PI 8P3 Industrial (-40° C to 85° C) AT17LV256-10NI 8S1 AT17LV256-10JI 20J AT17LV256-10SI 20S2 512-Kbit(1) AT17LV512-10PC 8P3 Commercial (0° C to 70° C)AT17LV512-10JC 20J AT17LV512-10PI 8P3 Industrial (-40° C to 85° C)AT17LV512-10JI 20J 1-Mbit(1) AT17LV010-10PC 8P3 Commercial (0° C to 70° C)AT17LV010-10JC 20J AT17LV010-10PI 8P3 Industrial (-40° C to 85° C)AT17LV010-10JI 20J 2-Mbit(1) AT17LV002-10JC 20J Commercial (0° C to 70° C) AT17LV002-10JI 20J Industrial (-40° C to 85° C)
2321I–CNFG–2/08 AT17LV65/128/256/512/010/002/040 Note: 1. For operating 5V operating voltage, please re fer to the corresponding AC and DC Characteristics.
22.2 Green Package Options (Pb/Halide-free/RoHS Compliant)
Memory Size Ordering Code Package Operation Range 256-Kbit(1) AT17LV256-10CU 8CN4 Industrial (-40° C to 85° C) AT17LV256-10JU 20J AT17LV256-10NU 8S1 AT17LV256-10PU 8P3 AT17LV256-10SU 20S2 512-Kbit (1) AT17LV512-10CU 8CN4 AT17LV512-10JU 20J 1-Mbit(1) AT17LV010-10CU 8CN4 AT17LV010-10JU 20J AT17LV010-10PU 8P3 2-Mbit(1) AT17LV002-10CU 8CN4 AT17LV002-10JU 20J AT17LV002-10SU 20S2 AT17LV002-10TQU 44A 4-Mbit(1) AT17LV040-10TQU 44A
2321I–CNFG–2/08 AT17LV65/128/256/512/010/002/040 23. Packaging Information 23.1 8CN4 – LAP TITLE DRAWING NO.GPC REV. Package Drawing Contact: p ackagedrawings@atmel.com 8CN4DMH D 8CN4, 8-lead (6 x 6 x 1.04 mm Body), Lead Pitch 1.27mm, Leadless Array Package (LAP) 2/15/08 COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A 0.94 1.04 1.14 A1 0.30 0.34 0.38 b 0.45 0.50 0.55 1 D 5.89 5.99 6.09 E 5.89 5.99 6.09 e 1.27 BSC e1 1.10 REF L 0.95 1.00 1.05 1 L1 1.25 1.30 1.35 1 Note: 1. Metal Pad Dimensions. 2. All exposed metal area shall have the following finished platings. Ni: 0.0005 to 0.015 mm Au: 0.0005 to 0.001 mm Pin1 Corner Marked Pin1 Indentifier 0.10 mm TYP Top View L b e Side View A Bottom View E D
2321I–CNFG–2/08 AT17LV65/128/256/512/010/002/040 23.2 8P3 – PDIP
2325 Orchard Parkway
San Jose, CA 95131 TITLE DRAWING NO. R REV. 8P3, 8-lead, 0.300" Wide Body, Plastic Dual In-line Package (PDIP) 01/09/02 8P3 B D E e Lb2 b A2 A N eA c
4 PLCS
(Unit of Measure = inches) SYMBOL MIN NOM MAX NOTE Notes: 1. This drawing is for general information only; refer to JEDEC Drawing MS-001, Variation BA for additional information. 2. Dimensions A and L are measured with the package seated in JEDEC seating plane Gauge GS-3. 3. D, D1 and E1 dimensions do not include mold Flash or protrusions. Mold Flash or protrusions shall not exceed 0.010 inch. 4. E and eA measured with the leads constrained to be perpendicular to datum. 5. Pointed or rounded lead tips are preferred to ease insertion. A 0.210 2 A2 0.115 0.130 0.195 b 0.014 0.018 0.022 5 b2 0.045 0.060 0.070 6 b3 0.030 0.039 0.045 6 c 0.008 0.010 0.014 D 0.355 0.365 0.400 3 D1 0.005 3 E 0.300 0.310 0.325 4 E1 0.240 0.250 0.280 3 e 0.100 BSC eA 0.300 BSC 4 L 0.115 0.130 0.150 2
2321I–CNFG–2/08 AT17LV65/128/256/512/010/002/040 23.3 8S1 – SOIC 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TITLE DRAWING NO. R REV. Note: 3/17/05 8S1, 8-lead (0.150" Wide Body), Plastic Gull Wing Small Outline (JEDEC SOIC) 8S1C COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A1 0.10 – 0.25 These drawings are for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. ØØ EE NN TOP VIEW CC E1E1 END VIEW AA bb LL A1A1 ee DD SIDE VIEW
2321I–CNFG–2/08 AT17LV65/128/256/512/010/002/040 23.4 20J – PLCC San Jose, CA 95131R TITLE DRAWING NO. REV. Notes: 1. This package conforms to JEDEC reference MS-018, Variation AA. 2. Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is .010"(0.254 mm) per side. Dimension D1 and E1 include mold mismatch and are measured at the extreme material condition at the upper or lower parting line. 3. Lead coplanarity is 0.004" (0.102 mm) maximum. A 4.191 – 4.572 A1 2.286 – 3.048 A2 0.508 – – D 9.779 – 10.033 D1 8.890 – 9.042 Note 2 E 9.779 – 10.033 E1 8.890 – 9.042 Note 2 D2/E2 7.366 – 8.382 B 0.660 – 0.813 B1 0.330 – 0.533 e 1.270 TYP COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE 1.14(0.045) X 45˚ PIN NO. 1 IDENTIFIER 1.14(0.045) X 45˚ 0.51(0.020)MAX 0.318(0.0125) 0.191(0.0075) 45˚ MAX (3X) A D2/E2 B e E1 E D 20J, 20-lead, Plastic J-leaded Chip Carrier (PLCC) B20J 10/04/01
2321I–CNFG–2/08 AT17LV65/128/256/512/010/002/040 23.5 20S2 – SOIC
2321I–CNFG–2/08 AT17LV65/128/256/512/010/002/040 23.6 44A – TQFP San Jose, CA 95131 TITLE DRAWING NO. R REV. 44A, 44-lead, 10 x 10 mm Body Size, 1.0 mm Body Thickness, 0.8 mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP) B44A 10/5/2001 PIN 1 IDENTIFIER 0˚~7˚ PIN 1 L C A1 A2 A D e E1 E B COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE Notes: 1. This package conforms to JEDEC reference MS-026, Variation ACB. 2. Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is 0.25 mm per side. Dimensions D1 and E1 are maximum plastic body size dimensions including mold mismatch. 3. Lead coplanarity is 0.10 mm maximum. A – – 1.20 A1 0.05 – 0.15 A2 0.95 1.00 1.05 D 11.75 12.00 12.25 D1 9.90 10.00 10.10 Note 2 E 11.75 12.00 12.25 E1 9.90 10.00 10.10 Note 2 B 0.30 – 0.45 C 0.09 – 0.20 L 0.45 – 0.75 e 0.80 TYP
2321I–CNFG–2/08 AT17LV65/128/256/512/010/002/040 24. Revision History Revision Level – Release Date History H – March 2006 Added last-time buy fo r AT17LVXXX-10CC and AT17LVXXX-10CI. I – February 2008 Removed -10SC, 10SI, -10TQC, -10TQI, -10BJC and -10BJI devices from ordering information.
2321I–CNFG–2/08 Headquarters International Atmel Corporation San Jose, CA 95131 USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Atmel Asia Room 1219 Chinachem Golden Plaza
77 Mody Road Tsimshatsui
Tel: (852) 2721-9778 Fax: (852) 2722-1369 Atmel Europe Le Krebs 8, Rue Jean-Pierre Timbaud BP 309
78054 Saint-Quentin-en-
9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Product Contact Web Site www.atmel.com Technical Support configurator@atmel.com Sales Contact www.atmel.com/contacts Literature Requests www.atmel.com/literature Disclaimer: The information in this document is provided in connection with Atmel products. No lice nse, express or imp lied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL ’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL ’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTOR Y WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WA RRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDEN- TAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF TH E POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with re spect to the accuracy or comple teness of the contents of this document and reserves the rig ht to make change s to specifications and product descriptions at any time withou t notice. Atmel does not make any commitmen t to update the information contained her ein. Unless specifically provided otherwise, Atmel products are no t suitable for, and shall not be used in, automotive applicatio ns. Atmel’s products are not int ended, authorized, or warranted for use as components in applications in tended to support or sustain life. © 2008 Atmel Corporation. All rights reserved. Atmel ®, logo and combinations thereof, and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other te rms and product names may be trademarks of others.