AT17LV65A_06 ATMEL
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 18
Technical content
Features
- EE Programmable 65,536 x 1-, 131,072 x 1-, 262,144 x 1-, 524,288 x 1-, 1,048,576 x 1- and 2,097,152 x 1-bit Serial Memories Designed to Store Configuration Programs for Altera® FLEX® and APEX™ FPGAs (Device Selection Guide Included) Available as a 3.3V (±10%) and 5.0V (±5% Commercial, ±10% Industrial) Version In-System Programmable (ISP) via 2-wire Bus Simple Interface to SRAM FPGAs Compatible with Atmel AT6000, AT40K and AT94K Devices, Altera FLEX, APEX Devices, ORCA® FPGAs, Xilinx® XC3000, XC4000, XC5200, Spartan®, Virtex™ FPGAs, Motorola MPA1000 FPGAs Cascadable Read-back to Support Additional Configurations or Higher-density Arrays Very Low-power CMOS EEPROM Process Programmable Reset Polarity Available 8-lead PDIP, 20-lead PLCC and 32-lead TQFP Packages (Pin Compatible Across Product Family) Emulation of Atmel’s AT24CXXX Serial EEPROMs Low-power Standby Mode High-reliability – Endurance: 100,000 Write Cycles – Data Retention: 90 Years for Industrial Parts (at 85°C) and 190 Years for Commercial Parts (at 70°C) Green (Pb/Halide-free/RoHS Compliant) Package Options Available 1. Description The AT17A series FPGA configuration EEPROMs (Configurators) provide an easy-to- use, cost-effective configuration memory for Field Programmable Gate Arrays. The AT17A series device is packaged in the 8-lead PDIP (1), 20-lead PLCC and 32-lead TQFP, see Table 1-1. The AT17A series configurator uses a simple serial-access pro- cedure to configure one or more FPGA devices. The user can select the polarity of the reset function by programming four EEPR OM bytes.These devices also support a write-protection mechanism within its programming mode. Note: 1. The 8-lead LAP , PDIP and SOIC packages for the AT17LV65A/128A/256A do not have an A label. However, the 8-lead packages are pin compatible with the 8-lead package of Altera’s EEPROMs, refer to the AT17LV65/128/256/512/010/002/040 datasheet available on the Atmel web site for more information. The AT17A series configurators can be programmed with industry-standard program- mers, Atmel’s ATDH2200E Programming Kit or Atmel’s ATDH2225 ISP Cable. Table 1-1. AT17A Series Packages Package AT17LV65A/ AT17LV128A/ AT17LV256A AT17LV512A AT17LV010A AT17LV002A 8-lead PDIP Ye s Ye s Ye s – 20-lead PLCC Y e sY e sY e sY e s 32-lead TQFP –– Y e s Y e s FPGA Configuration EEPROM Memory AT17LV65A AT17LV128A AT17LV256A AT17LV512A AT17LV010A AT17LV002A 3.3V and 5V System Support 2322G–CNFG–03/06
2322G–CNFG–03/06 AT17LV65A/128A/256A/512A/002A Figure 2-4. Block Diagram Notes: 1. This pin is only available on AT17LV65A/128A/256A devices. 2. This pin is only available on AT17LV512A/010A/002A devices. 3. The nCASC feature is not available on the AT17LV65A device. POWER ON RESET SER_EN WP1 (2) READY (2) DCLK nCS nCASCRESET/OE (WP (1) OSCILLATOR (3) OSCILLATOR CONTROLL
2322G–CNFG–03/06 AT17LV65A/128A/256A/512A/002A 3. Device Description The control signals for the conf iguration EEPROM (nCS, RESET/OE and DCLK) interface directly with the FPGA device control signals. All FPGA devices can control the entire configura- tion process and retrieve data from the configuration EEPROM without requiring an external controller. The configuration EEPROM’s RESET/OE and nCS pins control the tri-state buffer on the DATA output pin and enable t he address counter and the oscillator. When RESET/OE is driven Low, the configuration EEPROM resets its address counter and tri-states its DATA pin. The nCS pin also controls the output of the AT17A series configurator. If nCS is held High after the RESET/OE pulse, the counter is disabled and the DATA output pin is tri-stated. When nCS is driven subsequently Low, the counter and the DA TA output pin are enabled. When RESET/OE is driven Low again, the address counter is reset and the DATA output pin is tri-stated, regard- less of the state of the nCS. When the configurator has driven out all of it s data and nCASC is driven Low, the device tri- states the DATA pin to avoid contention with ot her configurators. Upon power-up, the address counter is automatically reset. This is the default setting for the device. Since almost all FPGAs use RESET Low and OE High, this document will describe RESET/OE. 4. Pin Description Note: 1. The nCASC feature is not available on the AT17LV65A device. Name I/O AT17LV65A/ AT17LV128A/ AT17LV256A AT17LV512A/ AT17LV010A AT17LV002A PLCC PDIP PLCC TQFP PLCC TQFP DATA I/O 2 1 2 31 2 31 D C L K I 424242 W P 1 I ––5454 RESET/OE I 838787 nCS I9 4 9 1 0 9 1 0 GND 10 5 10 12 10 12 nCASC O 1 2 6 1 21 51 21 5 A2 I READY O – – 15 20 15 20 SER_EN I 18 7 18 23 18 23 VCC 2 0 8 2 02 72 02 7
2322G–CNFG–03/06 AT17LV65A/128A/256A/512A/002A
4.1 DATA
Three-state DATA output for configuration. Open-collector bi-directional pin for programming.
4.2 DCLK
Clock output or clock input. Rising edges on DCLK increment the internal address counter and present the next bit of data to the DATA pin. The counter is incremented only if the RESET/OE input is held High, the nCS input is held Low, and all configuration data has not been transferred to the target device (otherwise, as the master device, the DCLK pin drives Low).
4.3 WP1
WRITE PROTECT (1). This pin is used to protect portions of memory during programming, and it is disabled by default due to internal pull-down resistor. This input pin is not used during FPGA loading operations. This pin is only available on AT17LV512A/010A/002A devices.
4.4 RESET/OE
Output Enable (active High) and RESET (active Low) when SER_EN is High. A Low logic level resets the address counter. A High logic level (with nCS Low) enables DATA and permits the address counter to count. In the mode, if this pin is Low (reset), the inte rnal oscillator becomes inactive and DCLK drives Low. The logic polarity of this input is programmable and must be pro- grammed active High (RESET active Low) by the user during programming for Altera applications. 4.5 WP Write protect (WP) input (when nCS is Low) during programming only (SER_EN Low) . When WP is Low, the entire memory can be written. When WP is enabled (High), the lowest block of the memory cannot be written. This pin is only available on AT17LV65A/128A/256A devices. 4.6 nCS Chip Select input (active Low). A Low input (w ith OE High) allows DCLK to increment the address counter and enables DATA to drive out. If the AT17A series is reset with nCS Low, the device initializes as the first (and master) device in a daisy-chain. If the AT17A series is reset with nCS High, the device initializes as a subsequent AT17A series device in the chain.
4.7 GND
Ground pin. A 0.2 µF decoupling capacitor between VCC and GND is recommended. 4.8 nCASC Cascade Select Output (active Low). This output goes Low when the address counter has reached its maximum value. In a daisy-chain of AT17A series devices, the nCASC pin of one device is usually connected to the nCS input pin of the next device in the chain, which permits DCLK from the master configurator to clock data from a subsequent AT17A series device in the chain. This feature is not available on the AT17LV65A device. 4.9 A2 Device selection input, A2. This is used to enable (or select) the device during programming (i.e., when SER_EN is Low). A2 has an internal pull-down resistor.
2322G–CNFG–03/06 AT17LV65A/128A/256A/512A/002A
4.10 READY
Open collector reset state indicator. Driven Low during power-on reset cycle, released when power-up is complete. (recommended 4.7 kΩ pull-up on this pin if used).
4.11 SER_EN
Serial enable must be held High during FP GA loading operations. Bringing SER_EN Low enables the 2-wire Serial Programming Mode. For non-ISP applications, SER_EN should be tied to VCC.
4.12 V CC
3.3V (±10%) and 5.0V (±5% Commercial, ±10% Industrial) power supply pin. 5. FPGA Master Serial Mode Summary The I/O and logic functions of any SRAM-based FPGA are established by a configuration pro- gram. The program is loaded either automatically upon power-up, or on command, depending on the state of the FPGA mode pins. In Master mode, the FPGA automatically loads the config- uration program from an external memory. The AT17A Serial Configuration EEPROM has been designed for compatibility with the Master Serial mode. This document discusses the Altera FLEX FPGA device interfaces 6. Control of Configuration Most connections between the FPGA device a nd the AT17A Serial EEPROM are simple and self-explanatory. The DATA output of the AT17A series configurator drives DIN of the FPGA devices. The master FPGA DCLK output or external clock source drives the DCLK input of the AT17A series configurator. The nCASC output of any AT17A series configurator drives the nCS input of the next configurator in a cascaded chain of EEPROMs. SER_EN must be connected to VCC (except during ISP). 7. Cascading Serial Configuration EEPROMs For multiple FPGAs configured as a daisy-chain, or for FPGAs requiring larger configuration memories, cascaded configurators provide additional memory. After the last bit from the first configurator is read, the next clock signal to the configurator asserts its nCASC output low and disables its DATA line driver. The second configurator recog- nizes the low level on its nCS input and enables its DATA output. After configuration is complete, the address counters of all cascaded configurators are reset if the RESET/OE on each configurator is driven to a Low level. If the address counters ar e not to be reset upon co mpletion, then the RESET/OE input can be tied to a High level. The AT17LV65A devices do not have the nCASC feature to perform cascaded configurations.
2322G–CNFG–03/06 AT17LV65A/128A/256A/512A/002A 8. AT17A Series Reset Polarity The AT17A series configurator allows the user to program the polarity of the RESET/OE pin as either RESET/OE or RESET /OE. This feature is supported by industry-standard programmer algorithms. 9. Programming Mode The programming mode is entered by bringing SER_EN Low. In this mode the chip can be pro- grammed by the 2-wire serial bus. The programming is done at V CC supply only. Programming super voltages are generated inside the chip. 10. Standby Mode The AT17LV65A/128A/256A enters a low-power standby mode whenever nCS is asserted High. In this mode, the configurator consumes less than 50 µA of current at 3.3V (100 µA for the AT17LV512A/010A/002A). The output remains in a high-impedance state regardless of the state of the RESET/OE input. 11. Absolute Maximum Ratings* Maximum Ratings may cause permanent dam- age to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those listed under oper- ating conditions is not implied. Exposure to Abso- lute Maximum Rating conditions for extended periods of time may affect device reliability. Voltage on Any Pin CC +0.5V 12. Operating Conditions Symbol Description 3.3V 5V UnitsMin Max Min Max VCC Commercial Supply voltage relative to GND -0°C to +70°C 3.0 3.6 4.75 5.25 V Industrial Supply voltage relative to GND -40°C to +85°C 3 . 03 . 64 . 55 . 5 V
2322G–CNFG–03/06 AT17LV65A/128A/256A/512A/002A 13. DC Characteristics VCC = 3.3V ± 10% Symbol Description AT17LV65A/ AT17LV128A/ AT17LV256A AT17LV512A/ AT17LV010A AT17LV002A UnitsMin Max Min Max Min Max VIH High-level Input Voltage 2.0 V CC 2.0 V CC 2.0 V CC V VIL Low-level Input Voltage 0 0.8 0 0.8 0 0.8 V VOH High-level Output Voltage (IOH = -2.5 mA) Commercial 2.4 2.4 2.4 V VOL Low-level Output Voltage (IOL = +3 mA) 0.4 0.4 0.4 V VOH High-level Output Voltage (IOH = -2 mA) Industrial 2.4 2.4 2.4 V VOL Low-level Output Voltage (IOL = +3 mA) 0.4 0.4 0.4 V ICCA Supply Current, Active Mode 5 5 5 mA IL Input or Output Leakage Current (VIN = VCC or GND) -10 10 -10 10 -10 10 µA ICCS Supply Current, Standby Mode Commercial 50 100 150 µA Industrial 100 100 150 µA 14. DC Characteristics VCC = 5V ± 5% Commercial; VCC = 5V ± 10% Industrial Symbol Description AT17LV65A/ AT17LV128A/ AT17LV256A AT17LV512A/ AT17LV010A AT17LV002A UnitsMin Max Min Max Min Max VIH High-level Input Voltage 2.0 V CC 2.0 V CC 2.0 V CC V VIL Low-level Input Voltage 0 0.8 0 0.8 0 0.8 V VOH High-level Output Voltage (IOH = -2.5 mA) Commercial 3.7 3.86 3.86 V VOL Low-level Output Voltage (IOL = +3 mA) 0.32 0.32 0.32 V VOH High-level Output Voltage (IOH = -2 mA) Industrial 3.6 3.76 3.76 V VOL Low-level Output Voltage (IOL = +3 mA) 0.37 0.37 0.37 V ICCA Supply Current, Active Mode 10 10 10 mA IL Input or Output Leakage Current (VIN = VCC or GND) -10 10 -10 10 -10 10 µA ICCS1 Supply Current, Standby Mode Commercial 75 200 350 µA Industrial 150 200 350 µA
2322G–CNFG–03/06 AT17LV65A/128A/256A/512A/002A 15. AC Waveforms 16. AC Waveforms when Cascading nCS RESET/OE DCLK DATA TSCE TLC THC TOE TCE TCAC TOH THOE THCE TSCE TDF TOH RESET/OE nCS DCLK DATA nCASL TCDF TOCK LAST BIT TOCE TOOE TOCE FIRST BIT
2322G–CNFG–03/06 AT17LV65A/128A/256A/512A/002A Notes: 1. AC test lead = 50 pF . 2. Float delays are measured with 5 pF AC loads. Transition is measured ± 200 mV from steady-state active levels. Notes: 1. AC test lead = 50 pF . 2. Float delays are measured with 5 pF AC loads. Transition is measured ± 200 mV from steady-state active levels. 17. AC Characteristics VCC = 3.3V ± 10% Symbol Description AT17LV65A/128A/256A AT17LV512A/010A/002A Units Commercial Industrial Commercial Industrial Min Max Min Max Min Max Min Max TOE (1) OE to Data Delay 50 55 50 55 ns TCE (1) CE t o D a t a D e l a y 6 06 05 56 0 n s TCAC (1) CLK to Data Delay 75 80 55 60 ns TOH Data Hold from CE, O E , o r C L K 0000 n s TDF (2) CE or OE to Data Float Delay 55 55 50 50 ns TLC CLK Low Time 25 25 25 25 ns THC CLK High Time 25 25 25 25 ns TSCE CE Setup Time to CLK (to guarantee proper counting) 35 60 30 35 ns THCE CE Hold Time from CLK (to guarantee proper counting) 0000 n s THOE OE High Time (guarantees counter is reset) 25 25 25 25 ns FMAX Maximum Input Clock Frequency 10 10 15 10 MHz 18. AC Characteristics when Cascading VCC = 3.3V ± 10% Symbol Description AT17LV65A/128A/256A AT17LV512A/010A/002A Units Commercial Industrial Commercial Industrial Min Max Min Max Min Max Min Max TCDF (2) CLK to Data Float Delay 60 60 50 50 ns TOCK (1) CLK to CEO Delay 55 60 50 55 ns TOCE (1) CE to CEO Delay 55 60 35 40 ns TOOE (1) RESET/OE to CEO Delay 40 45 35 35 ns FMAX Maximum Input Clock Frequency 8 8 12.5 10 MHz
2322G–CNFG–03/06 AT17LV65A/128A/256A/512A/002A Notes: 1. AC test lead = 50 pF . 2. Float delays are measured with 5 pF AC loads. Transition is measured ± 200 mV from steady-state active levels. Notes: 1. AC test lead = 50 pF . 2. Float delays are measured with 5 pF AC loads. Transition is measured ± 200 mV from steady-state active levels. 19. AC Characteristics VCC = 5V ± 5% Commercial; VCC = 5V ± 10% Industrial Symbol Description AT17LV65A/128A/256A AT17LV512A/010A/002A Units Commercial Industrial Commercial Industrial Min Max Min Max Min Max Min Max TOE (1) OE to Data Delay 30 35 30 35 ns TCE (1) CE to Data Delay 45 45 45 45 ns TCAC (1) CLK to Data Delay 50 55 50 50 ns TOH Data Hold from CE, OE, or CLK 0 0 0 0 ns TDF (2) CE or OE to Data Float Delay 50 50 50 50 ns TLC CLK Low Time 20 20 20 20 ns THC CLK High Time 20 20 20 20 ns TSCE CE Setup Time to CLK (to guarantee proper counting) 35 40 20 25 ns THCE CE Hold Time from CLK (to guarantee proper counting) 0000 n s THOE OE High Time (guarantees counter is reset) 20 20 20 20 ns FMAX Maximum Input Clock Frequency 12.5 12.5 15 15 MHz 20. AC Characteristics when Cascading VCC = 5V ± 5% Commercial; VCC = 5V ± 10% Industrial Symbol Description AT17LV65A/128A/256A AT17LV512A/010A/002A Units Commercial Industrial Commercial Industrial Min Max Min Max Min Max Min Max TCDF (2) CLK to Data Float Delay 50 50 50 50 ns TOCK (1) CLK to CEO D e l a y 3 54 03 54 0 n s TOCE (1) CE to CEO D e l a y 3 53 53 53 5 n s TOOE (1) RESET/OE to CEO D e l a y 3 03 53 03 0 n s FMAX Maximum Input Clock Frequency 10 10 12.5 12.5 MHz
2322G–CNFG–03/06 AT17LV65A/128A/256A/512A/002A Notes: 1. For more information refer to the “Thermal Characteri stics of Atmel’s Packages”, available on the Atmel web site. 2. Airflow = 0 ft/min. 21. Thermal Resistance Coefficients (1) Package Type AT17LV65A/ AT17LV128A/ AT17LV256A AT17LV512A/ AT17LV010A AT17LV002A 8P3 Plastic Dual Inline Package (PDIP) θJC [°C/W] 37 θJA °C/W 107 20J Plastic Leaded Chip Carrier (PLCC) θJC [°C/W] 35 35 35 32A Thin Plastic Quad Flat Package (TQFP) θJC [°C/W] θJA °C/W 44J Plastic Leaded Chip Carrier (PLCC) θJC [°C/W] – – 15 θJA °C/W –– 5 0
2322G–CNFG–03/06 AT17LV65A/128A/256A/512A/002A 22. Ordering Information Figure 22-1. Ordering Code(1) Note: 1. The 8-lead LAP and SOIC packages for the AT17LV65A/128A/2 56A do not have an A label. However, the 8-lead packages are pin compatible with the 8-lead package of Altera’s EEPROMs, refer to the AT17LV65/128/256/512/010/002/040 datasheet available on the Atmel web site for more information. Package Type 8P3 8-lead, 0.300" Wide, Plastic Dual Inline Package (PDIP) 20J 20-lead, Plastic J-leaded Chip Carrier (PLCC) 32A 32-lead, Thin (1.0 mm) Plastic Quad Flat Package Carrier (TQFP) Vo l t a g e Size (Bits) Special Pinouts Package Te mperature 65 = 65K A = Altera C = Commercial 128 = 128K Blank = Xilinx/Atmel/ = 8P3 I = Industrial 256 = 256K 512 = 512K = 20J 010 = 1M = 32A 002 = 2M AT17LV65A-10PC P J Q 3.3V Nominal to 5V Nominal Other U = Fully Green
2322G–CNFG–03/06 AT17LV65A/128A/256A/512A/002A Notes: 1. Currently, there are two types of low-density configur ators. The new version will be identified by a “B” after the datacode. The “B” version is fully backward-compatible with the original devices so existing customers will not be affected. The new parts no longer require a MUX for ISP . See programming specification for more details. 2. Use 64-Kbit density parts to replace Altera EPC1064. 3. Use 256-Kbit density parts to replace Altera EPC1213. 4. Use 512-Kbit density parts to replace Altera EPC1441. 5. Use 1-Mbit density parts to replace Altera EPC1 6. Use 2-Mbit density parts to replace Altera EPC2. Atmel AT17LV002A devices do not support JTAG programming; Atmel AT17LV002A devices use a 2-wire serial interface for in-system programming. 7. For operating voltage of 5V ±10%, please refe r to the 5V ±10% AC and DC Characteristics.
22.1 Standard Package Options (1)
Memory Size Ordering Code Package Operation Range 64-Kbit(2)(7) AT17LV65A-10JC 20J Commercial (0°C to 70°C) AT17LV65A-10JI 20J Industrial (-40°C to 85°C) 128-Kbit(7) AT17LV128A-10JC 20J Commercial (0°C to 70°C) AT17LV128A-10JI 20J Industrial (-40°C to 85°C) 256-Kbit(3)(7) AT17LV256A-10JC 20J Commercial (0°C to 70°C) AT17LV256A-10JI 20J Industrial (-40°C to 85°C) 512-Kbit(4)(7) AT17LV512A-10PC AT17LV512A-10JC 8P3 20J Commercial (0°C to 70°C) AT17LV512A-10PI AT17LV512A-10JI 8P3 20J Industrial (-40°C to 85°C) 1-Mbit(5)(7) AT17LV010A-10PC AT17LV010A-10JC AT17LV010A-10QC 8P3 20J 32A Commercial (0°C to 70°C) AT17LV010A-10PI AT17LV010A-10JI AT17LV010A-10QI 8P3 20J 32A Industrial (-40°C to 85°C) 2-Mbit(6)(7) AT17LV002A-10JC AT17LV002A-10QC 20J 32A Commercial (0°C to 70°C) AT17LV002A-10JI AT17LV002A-10QI 20J 32A Industrial (-40°C to 85°C)
22.2 Green Package Options (Pb/Halide-free/RoHS Compliant)(1)
Memory Size Ordering Code Package Operation Range 512-Kbit(4)(7) AT17LV512A-10JU 20J Industrial (-40°C to 85°C) 1-Mbit(5)(7) AT17LV010A-10JU AT17LV010A-10PU 20J 8P3 Industrial (-40°C to 85°C) 2-Mbit(4)(7) AT17LV002A-10JU 20J Industrial (-40°C to 85°C)
2322G–CNFG–03/06 AT17LV65A/128A/256A/512A/002A 23. Packaging Information 23.1 8P3 – PDIP
2325 Orchard Parkway
San Jose, CA 95131 TITLE DRAWING NO. R REV. 8P3, 8-lead, 0.300" Wide Body, Plastic Dual In-line Package (PDIP) 01/09/02 8P3 B D E e Lb2 b A2 A N eA c
4 PLCS
(Unit of Measure = inches) SYMBOL MIN NOM MAX NOTE Notes: 1. This drawing is for general information only; refer to JEDEC Drawing MS-001, Variation BA for additional information. 2. Dimensions A and L are measured with the package seated in JEDEC seating plane Gauge GS-3. 3. D, D1 and E1 dimensions do not include mold Flash or protrusions. Mold Flash or protrusions shall not exceed 0.010 inch. 4. E and eA measured with the leads constrained to be perpendicular to datum. 5. Pointed or rounded lead tips are preferred to ease insertion. A 0.210 2 A2 0.115 0.130 0.195 b 0.014 0.018 0.022 5 b2 0.045 0.060 0.070 6 b3 0.030 0.039 0.045 6 c 0.008 0.010 0.014 D 0.355 0.365 0.400 3 D1 0.005 3 E 0.300 0.310 0.325 4 E1 0.240 0.250 0.280 3 e 0.100 BSC eA 0.300 BSC 4 L 0.115 0.130 0.150 2
2322G–CNFG–03/06 AT17LV65A/128A/256A/512A/002A 23.2 20J – PLCC San Jose, CA 95131R TITLE DRAWING NO. REV. Notes: 1. This package conforms to JEDEC reference MS-018, Variation AA. 2. Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is .010"(0.254 mm) per side. Dimension D1 and E1 include mold mismatch and are measured at the extreme material condition at the upper or lower parting line. 3. Lead coplanarity is 0.004" (0.102 mm) maximum. A 4.191 – 4.572 A1 2.286 – 3.048 A2 0.508 – – D 9.779 – 10.033 D1 8.890 – 9.042 Note 2 E 9.779 – 10.033 E1 8.890 – 9.042 Note 2 D2/E2 7.366 – 8.382 B 0.660 – 0.813 B1 0.330 – 0.533 e 1.270 TYP COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE 1.14(0.045) X 45˚ PIN NO. 1 IDENTIFIER 1.14(0.045) X 45˚ 0.51(0.020)MAX 0.318(0.0125) 0.191(0.0075) 45˚ MAX (3X) A D2/E2 B e E1 E D 20J, 20-lead, Plastic J-leaded Chip Carrier (PLCC) B20J 10/04/01
2322G–CNFG–03/06 AT17LV65A/128A/256A/512A/002A 23.3 32A – TQFP San Jose, CA 95131 TITLE DRAWING NO. R REV. 32A, 32-lead, 7 x 7 mm Body Size, 1.0 mm Body Thickness, 0.8 mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP) B32A 10/5/2001 PIN 1 IDENTIFIER 0˚~7˚ PIN 1 L C A1 A2 A D e E1 E B Notes: 1. This package conforms to JEDEC reference MS-026, Variation ABA. 2. Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is 0.25 mm per side. Dimensions D1 and E1 are maximum plastic body size dimensions including mold mismatch. 3. Lead coplanarity is 0.10 mm maximum. A – – 1.20 A1 0.05 – 0.15 A2 0.95 1.00 1.05 D 8.75 9.00 9.25 D1 6.90 7.00 7.10 Note 2 E 8.75 9.00 9.25 E1 6.90 7.00 7.10 Note 2 B 0.30 – 0.45 C 0.09 – 0.20 L 0.45 – 0.75 e 0.80 TYP COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE
Printed on recycled paper. 2322G–CNFG–03/06 Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL ’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL ’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTOR Y WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO , THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICU LAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR I NCIDEN- TAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF AT MEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or co mpleteness of the contents of this document and reserves the rig ht to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained her ein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not int ended, authorized, or warranted for use as components in applications in tended to support or sustain life. Atmel Corporation Atmel Operations San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Regional Headquarters Europe Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland Tel: (41) 26-426-5555 Fax: (41) 26-426-5500 Asia Room 1219 Chinachem Golden Plaza
77 Mody Road Tsimshatsui
Tel: (852) 2721-9778 Fax: (852) 2722-1369 Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Memory San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 Microcontrollers San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 La Chantrerie BP 70602
44306 Nantes Cedex 3, France
13106 Rousset Cedex, France
1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland Tel: (44) 1355-803-000 Fax: (44) 1355-242-743 RF/Automotive Theresienstrasse 2 Postfach 3535
74025 Heilbronn, Germany
1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom Avenue de Rochepleine BP 123
38521 Saint-Egreve Cedex, France
Atmel Programmable SLI Hotline (408) 436-4119 Atmel Programmable SLI e-mail configurator@atmel.com FAQ Available on web site Literature Requests www.atmel.com/literature © Atmel Corporation 2006 . All rights reserved. Atmel ®, logo and combinations thereof, Everywhere Y ou Are ® and others, are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.