AT17C512A ATMEL
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 11
Technical content
Features
- Serial EEPROM Family for Configuring Altera FLEX 10K Devices
- Simple, Easy-to-use 4-pin Interface
- E2 Programmable 1M Bit Serial Memories Designed To Store Configuration Programs For Programmable Gate Arrays
- Cascadable To Support Additional Configurations or Future Higher-density Arrays
- Low-power CMOS EEPROM Process
- Programmable Reset Polarity
- Available in the Space-efficient Surface-mount PLCC Package
- In-System Programmable Via 2-Wire Bus
- Emulation of 24CXX Serial EPROMs
- Available in 3.3V ±±±± 10% L V and 5V ±±±± 5% C Versions
Description
The AT17C512/010A and AT17LV512/010A (AT17A Series) FPGA Configuration EEPROMs (Configurators) provide and easy-to-use, cost-effective configuration memory for programming Altera FLEX Field Programmable Gate Arrays, FPGA, (the “devices”). The AT17A Series is packaged in the popular 20-pin PLCC package. The AT17A Series family uses a simple serial-access procedure to configure one or more FPGA devices. The AT17A Series organization supplies enough memory to configure one or multiple smaller FPGAs. Using a special feature of the AT17A Series, the user can select the polarity of the reset function by programming an EEPROM byte. The AT17C/LV512/010A parts generate their own internal clock and can be used as a sys- tem “master” for loading the FPGA devices. The Atmel devices also supports a system friendly READY pin and a write protect mechanism. The READY pin is used to simplify system power-up considerations. The WP1 pin is used to protect part of the device memory during in-system programming. The AT17A Series can be programmed with industry standard programmers. FPGA Serial Configuration Memories AT17C512A AT17LV512A AT17C010A AT17LV010A Rev. 0974A–04/98 Pin Configurations 20-Pin PLCC DCLK WP1 NC NC RESET/OE SER_EN NC NC READY NC nCS GND NC nCASC NC NC DATA NC VCC NC
The control signals for configuration EEPROMs–nCS, OE, and DCLK–interface directly with the FPGA device control signals. All FPGA devices can control the entire configura- tion process and retrieve data from the configuration EEPROM without requiring an external intelligent control- ler. The configuration EEPROM device’s OE and nCS pins control the tri-state buffer on the DATA output pin and enable the address counter and the oscillator. When OE is driven low, the configuration EEPROM device resets the address counter and tri-states its DATA pin. The nCS pin controls the output of the AT17A Series. If nCS is held high after the OE reset pulse, the counter is disabled and the DATA output pin is tri-stated. When nCS is driven low, the counter and the DATA output pin are enabled. When OE is driven low again, the address counter is reset and the DATA output pin is tri-stated, regardless of the state of the nCS. When the configurator has driven out all of its data and nCASC is driven low, the device tri-states the DATA pin to avoid contention with other configurators. Upon power-up, the address counter is automatically reset. FPGA Device Configuration FPGA devices can be configured with an AT17A Series EEPROM. The AT17A Series device stores configuration data in its EEPROM array and clocks the data out serially with its internal oscillator. The OE, nCS, and DCLK pins supply the control signals for the address counter and the output tri-state buffer. The AT17A Series device sends a serial bitstream of configuration data to its DATA pin, which is connected to the DATA0 input pin on the FPGA device. When configuration data for a FPGA device exceeds the capacity of a single AT17A Series device, multiple AT17A Series devices can be serially linked together. When multi- ple AT17A Series devices are required, the nCASC and nCS pins provide handshaking between the AT17A Series devices. The position of an AT17A Series device in a chain deter- mines its operation. The first AT17A Series device in a Configurator chain is powered up or reset with nCS low and is configured for FPGA devices protocol. This AT17A Series device supplies all clock pulses to one or more FPGA devices and to any downstream AT17A Series dur- ing configuration. The first AT17A Series device also pro- vides the first stream of data to the FPGA devices during EEPROM CELL MATRIX ROW DECODER COLUMN DECODER TC nCSDCLK OE nCASC DATA BIT COUNTER OSC OSC CONTROL PROGRAMMING DATA SHIFT REGISTER PROGRAMMING MODE LOGIC ROW ADDRESS COUNTER SER_EN
first AT17A Series device goes into zero-power (idle) state. the nSTATUS is driven low, indicating a configuration error. Figure 1. FPGA Device Configured with Two AT17A Series Devices
(20-Pin PLCC) Pin Name Pin Type Description 2 DAT A Output Serial data output. 4 DCLK I/O Clock output or clock input. Rising edges on DCLK increment the internal address counter and present the next bit of data to the DA T A pin. The counter is incremented only if the OE input is held high, the nCS input is held low, and all configuration data has not been transferred to the target device (otherwise, in FPGA 10K master mode, the DCLK pin drives low). 5 WP1 Input WRITE PROTECT (1). Used to protect portions of memory during programming. See programming guide for details.
8 RESET
/OE Input Output enable (active high) and reset (active low). A low logic level resets the address counter. A high logic level enables DA T A and permits the address counter to count. In the mode, if this pin is low (reset), the internal oscillator becomes inactive and DCLK drives low. 9 nCS Input Chip select input (active low). A low input allows DCLK to increment the address counter and enables DA T A to drive out. If the A T17A Series is reset with nCS low, the device initializes as the first device in a daisy-chain. If the A T17A Series is reset with nCS high, the device initializes as the next A T17A Series device in the chain 10 GND Ground A 0.2 µF decoupling capacitor should be placed between the V CC and GND pins. 12 nCASC Output Cascade select output (active low). This output goes low when the address counter has reached its maximum value. In a daisy-chain of A T17A Series devices, the nCASC pin of one device is usually connected to the nCS input pin of the next device in the chain, which permits DCLK to clock data from the next A T17A Series device in the chain. A2 Input Device selection input, A2. This is used to enable (or select) the device during programming, when SER_EN is Low (see Programming Guide for more details) 15 READY Output Open collector reset state indicator. Driven Low during power-up reset, released when power-up is complete. (Recommend a 4.7KΩ Pull-up on this pin if used). 18 SER_EN Input Serial enable is normally high during FPGA loading operations. Bringing SER_EN Low, enables the two wire serial interface mode for programming. 20 V CC Power Power pin. Absolute Maximum Ratings* mum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other condi- tions beyond those listed under Operating Conditions is not implied. Exposure to Absolute Maximum Rat- ings conditions for extended periods of time may affect device reliability. Voltage on Any Pin CC + 0.5V
Commercial Supply voltage relative to GND -0°C to +70°C 4.75 5.25 3.0 3.6 V Industrial Supply voltage relative to GND -40°C to +85°C 4.5 5.5 3.0 3.6 V Military Supply voltage relative to GND -55°C to +125°C 4.5 5.5 3.0 3.6 V
VCC = 5V ± 5% Commercial / 5V ± 10% Ind./Mil. Symbol Description Min Max Units VIH High-level input voltage 2.0 V CC V VIL Low-level input voltage 0 0.8 V VOH High-level output voltage (IOH = -4 mA) Commercial 3.7 V VOL Low-level output voltage (IOL = +4 mA) 0.32 V VOH High-level output voltage (IOH = -4 mA) Industrial 3.6 V VOL Low-level output voltage (IOL = +4 mA) 0.37 V VOH High-level output voltage (IOH = -4 mA) Military 3.5 V VOL Low-level output voltage (IOL = +4 mA) 0.4 V ICCA Supply current, active mode 10 mA IL Input or output leakage current (VIN = VCC or GND) -10 10 µA ICCS Supply current, standby mode A T17010A/512A Commercial 150 µA Industrial/Military 150 µA DC Characteristics VCC = 3.3V ± 10% Symbol Description Min Max Units VIH High-level input voltage 2.0 V CC V VIL Low-level input voltage 0 0.8 V VOH High-level output voltage (IOH = -2.5 mA) Commercial 2.4 V VOL Low-level output voltage (IOL = +3 mA) 0.4 V VOH High-level output voltage (IOH = -2 mA) Industrial 2.4 V VOL Low-level output voltage (IOL = +3 mA) 0.4 V VOH High-level output voltage (IOH = -2 mA) Military 2.4 V VOL Low-level output voltage (IOL = +2.5 mA) 0.4 V ICCA Supply current, active mode 5 mA IL Input or output leakage current (VIN = VCC or GND) -10 10 µA ICCS Supply current, standby mode Commercial 50 µA Industrial/Military 50 µA
AC Characteristics When Cascading
Notes: 1. Preliminary specifications for military operating range only. 2. AC test load = 50 pF . 3. Float delays are measured with 5 pF AC loads. Transition is measured ± 200 mV from steady state active levels. AC Characteristics for AT17C010A/512A VCC = 5V ± 5% Commercial / VCC = 5V ± 10% Ind./Mil Symbol Description Commercial Industrial/Military UnitsMin Max Min Max TOE (2) OE to Data Delay 30 35 ns TCE (2) nCS to Data Delay 45 45 ns TCAC (2) CLK to Data Delay 50 55 ns TOH (2) Data Hold From nCS, OE, or DCLK 0 0 ns TDF (3) nCS or OE to Data Float Delay 50 50 ns TLC CLK Low Time Slave Mode 20 20 ns THC CLK High Time Slave Mode 20 20 ns TSCE nCS Setup Time to DCLK (to guarantee proper counting) 20 25 ns THCE nCS Hold Time to DCLK (to guarantee proper counting) 0 0 ns THOE OE High Time (Guarantees Counter Is Reset) 20 20 ns FMAX MAX Input Clock Frequency Slave Mode 15 15 MHz TLC CLK Low Time Master Mode 30 250 30 250 ns THC CLK High Time Master Mode 30 250 30 250 ns VRDY Ready Pin Open Collector Voltage 1.2 2.4 1.2 2.4 V AC Characteristics for AT17C010A/512A When Cascading VCC = 5V ± 5% Commercial / VCC = 5V ± 10% Ind./Mil. Symbol Description Commercial Industrial/Military UnitsMin Max Min Max TCDF (3) DCLK to Data Float Delay 50 50 ns TOCK (2) DCLK to nCASC Delay 35 40 ns TOCE (2) CE to nCASC Delay 35 35 ns TOOE (2) OE to nCASC Delay 30 30 ns
Notes: 1. Preliminary specifications for military operating range only. 2. AC test load = 50 pF . 3. Float delays are measured with 5 pF AC loads. Transition is measured ± 200 mV from steady state active levels. 4. During cascade FMAX = 12.5 MHz AC Characteristics for AT17C010A/512A VCC = 3.3V ± 10% Commercial / VCC = 3.3V ± 10% Ind./Mil Symbol Description Commercial Industrial/Military UnitsMin Max Min Max TOE (2) OE to Data Delay 50 55 ns TCE (2) nCS to Data Delay 55 60 ns TCAC (2) CLK to Data Delay 60 65 ns TOH (2) Data Hold From nCS, OE, or DCLK 0 0 ns TDF (3) nCS or OE to Data Float Delay 50 50 ns TLC CLK Low Time Slave Mode 25 25 ns THC CLK High Time Slave Mode 25 25 ns TSCE nCS Setup Time to DCLK (to guarantee proper counting) 35 40 ns THCE nCS Hold Time to DCLK (to guarantee proper counting) 0 0 ns THOE OE High Time (Guarantees Counter Is Reset) 20 20 ns FMAX (4) MAX Input Clock Frequency Slave Mode 15 10 MHz TLC CLK Low Time Master Mode 30 300 30 300 ns THC CLK High Time Master Mode 30 300 30 300 ns VRDY Ready Pin Open Collector Voltage 1.2 2.4 1.2 2.4 V AC Characteristics for AT17C010A/512A When Cascading VCC = 3.3V ± 10% Commercial / VCC =3.3V ± 10% Ind./Mil. Symbol Description Commercial Industrial/Military UnitsMin Max Min Max TCDF (3) DCLK to Data Float Delay 50 50 ns TOCK (2) DCLK to nCASC Delay 50 55 ns TOCE (2) CE to nCASC Delay 35 40 ns TOOE (2) OE to nCASC Delay 35 35 ns
Notes: 1. Use 512K density parts to replace Altera EPC1441. 2. Use 1M density parts to replace Altera EPC1 Ordering Information - 5V Devices Memory Size (K) Ordering Code Package Operation Range 512K(1) A T17C512A-10JC 20J Commercial (0°C to 70°C) A T17C512A-10JI 20J Industrial (-40°C to 85°C) 1M Bit(2) A T17C010A-10JC 20J Commercial (0°C to 70°C) A T17C010A-10JI 20J Industrial (-40°C to 85°C) Ordering Information - 3.3V Devices Memory Size (K) Ordering Code Package Operation Range 512K(1) A T17L V512A-10JC 20J Commercial (0°C to 70°C) A T17L V512A-10JI 20J Industrial (-40°C to 85°C) 1M Bit(2) A T17L V010A-10JC 20J Commercial (0°C to 70°C) A T17L V010A-10JI 20J Industrial (-40°C to 85°C) Package Type 20J 20-Lead, Plastic J-Leaded Chip Carrier (PLCC)
20J, 20-Lead, Plastic J-Leaded Chip Carrier (PLCC) Dimensions in Inches and (Millimeters) JEDEC STANDARD MS-018 AA