AT17LV256 ATMEL

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 24

Technical content

Features

  • EE Programmable 65,536 x 1-, 131,072 x 1-, 262,144 x 1-, 524,288 x 1-, 1,048,576 x 1-, 2,097,152 x 1-, and 4,194,304 x 1-bit Serial Memories Designed to Store Configuration Programs for Field Programmable Gate Arrays (FPGAs)  Supports both 3.3V and 5.0V Operating Voltage Applications  In-System Programmable (ISP) via Two-Wire Bus  Simple Interface to SRAM FPGAs  Compatible with Atmel AT6000, AT40K and AT94K Devices, Altera FLEX®, APEX™ Devices, Lucent ORCA®, Xilinx XC3000™ , XC4000™ , XC5200™ , Spartan®, Virtex® FPGAs  Cascadable Read-back to Support Additional Configurations or Higher-density Arrays  Very Low-power CMOS EEPROM Process  Programmable Reset Polarity  Available in 6 mm x 6 mm x 1 mm 8-lead LAP (Pin-compatible with 8-lead SOIC/VOIC Packages), 8-lead PDIP, 8-lead SOIC, 20-lead PLCC, 20-lead SOIC, 44-lead PLCC and 44-lead TQFP Packages  Emulation of Atmel’s AT24CXXX Serial EEPROMs  Low-power Standby Mode  High-reliability – Endurance: 100,000 Write Cycles – Data Retention: 90 Years for Industrial Parts (at 85°C) and 190 Years for Commercial Parts (at 70°C)

Description

The AT17LV series FPGA Configuration EEPROMs (Configurators) provide an easy- to-use, cost-effective configuration memory for Field Programmable Gate Arrays. The AT17LV series device is packaged in the 8-lead LAP , 8-lead PDIP , 8-lead SOIC, 20- lead PLCC, 20-lead SOIC, 44-lead PLCC and 44-lead TQFP , see Table 1. The AT17LV series Configurators uses a simple serial-access procedure to configure one or more FPGA devices. The user can select the polarity of the reset function by pro- gramming four EEPROM bytes. These devices also support a write-protection mechanism within its programming mode. The AT17LV series configurators can be programmed with industry-standard program- mers, Atmel’s ATDH2200E Programming Kit or Atmel’s ATDH2225 ISP Cable. Notes: 1. The 8-lead LAP package has the same footprint as the 8-lead SOIC. Since an 8- lead SOIC package is not available for the AT17LV512/010/002 devices, it is possi- ble to use an 8-lead LAP package instead. 2. The pinout for the AT17LV65/128/256 devices is not pin-for-pin compatible with the AT17LV512/010/002 devices. 3. Refer to the AT17Fxxx datasheet, available on the Atmel web site. Table 1. AT17LV Series Packages

2 AT17LV65/128/256/512/010/002/040

2321E–CNFG–06/03 Pin Configuration 8-lead LAP 8-lead SOIC 8-lead PDIP 20-lead PLCC Notes: 1. This pin is only available on AT17LV65/128/256 devices. 2. This pin is only available on AT17LV512/010/002 devices. DATA CLK (WP (1)) RESET/OE CE VCC SER_EN CEO (A2) GND DATA CLK (WP (1)) RESET/OE CE VCC SER_EN CEO (A2) GND DATA CLK (WP(1)) RESET/OE CE VCC SER_EN CEO (A2) GND CLK (WP1(2)) NC (WP(1)) RESET/OE (WP2(2)) NC CE NC SER_EN NC NC (READY (2)) CEO (A2) NC GND NC NC NC NC DATA NC VCC NC

AT17LV65/128/256/512/010/002/040 2321E–CNFG–06/03 20-lead SOIC(1) Note: 1. This pinout only applies to AT17LV65/128/256 devices. 20-lead SOIC(1) Note: 1. This pinout only applies to AT17LV512/010/002 devices. NC DATA NC CLK NC RESET/OE NC CE NC GND VCC NC NC SER_EN NC NC CEO (A2) NC NC NC DATA NC CLK NC NC NC NC RESET/OE NC CE VCC NC SER_EN NC NC NC NC CEO NC GND

4 AT17LV65/128/256/512/010/002/040

2321E–CNFG–06/03

44 PLCC

44 TQFP

Note: 1. This pin is only available on AT17LV002 devices. NC RESET/OE NC CE NC NC GND NC NC CEO/A2 NC NC CLK NC NC DATA NC VCC NC NC SER_EN NC (WP1(1)) NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC READY NC RESET/OE NC CE NC NC GND NC NC CEO(A2) NC NC CLK NC NC DATA NC VCC NC NC SER_EN NC NC NC NC NC NC NC (WP1(1)) NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC READY

AT17LV65/128/256/512/010/002/040 2321E–CNFG–06/03 Block Diagram Notes: 1. This pin is only available on AT17LV65/128/256 devices. 2. This pin is only available on AT17LV512/010/002 devices. Device Description The control signals for the configuration EEPROM (CE , RESET/OE and CCLK) inter- face directly with the FPGA device control signals. All FPGA devices can control the entire configuration process and retrieve data from the configuration EEPROM without requiring an external intelligent controller. The configuration EEPROM RESET/OE and CE pins control the tri-state buffer on the DATA output pin and enable the address counter. When RESET/OE is driven High, the configuration EEPROM resets its address count er and tri-states its DATA pin. The CE pin also controls the output of th e AT17LV series configurator. If CE is held High after the RESET/OE reset pulse, the counter is disabled and the DATA output pin is tri- stated. When OE is subsequently driven Low, the counter and the DATA output pin are enabled. When RESET/OE is driven High again, the address counter is reset and the DATA output pin is tri-stated, regardless of the state of CE. When the configurator has driven out all of its data and CEO is driven Low, the device tri-states the DATA pin to avoid contention with other configurators. Upon power-up, the address counter is automatically reset. This is the default setting for the device. Since almost all FPGAs use RESET Low and OE High, this document will describe RESET /OE. POWER ON RESET SER_EN WP1 (2) WP2 (2) (1)READY (2)

6 AT17LV65/128/256/512/010/002/040

2321E–CNFG–06/03 DATA Three-state DATA output for configuration. Open-collector bi-directional pin for programming. CLK Clock input. Used to increment the internal address and bit counter for reading and programming. WP1 WRITE PROTECT (1). Used to protect portions of memory during programming. Dis- abled by default due to internal pull-down resistor. This input pin is not used during FPGA loading operations. This pin is only available on AT17LV512/010/002 devices. RESET/OE Output Enable (active High) and RESET (active Low) when SER_EN is High. A Low level on RESET /OE resets both the address and bit counters. A High level (with CE Low) enables the data output driver. The logic polarity of this input is programmable as either RESET/OE or RESET/OE. For most applications, RESET should be programmed active Low. This document describes the pin as RESET/OE. WP Write protect (WP) input (when CE is Low) during programming only (SER_EN Low). When WP is Low, the entire memory can be written. When WP is enabled (High), the lowest block of the memory cannot be written. This pin is only available on AT17LV65/128/256 devices. WP2 WRITE PROTECT (2). Used to protect portions of memory during programming. Dis- abled by default due to internal pull-down resistor. This input pin is not used during FPGA loading operations. This pin is only available on AT17LV512/010 devices. Pin Description Name I/O AT17LV65/ AT17LV128/ AT17LV256 AT17LV512/ AT17LV010 AT17LV002 AT17LV040 DIP/ LAP/ SOIC PLCC SOIC DIP/ LAP PLCC SOIC DIP/ LAP/ SOIC PLCC SOIC PLCC TQFP PLCC TQFP DATA I/ O 1221211212 4 0 2 4 0 C L K I 2442432435 4 3 5 4 3 RESET/OE I 366368368 1 9 1 3 1 9 1 3 CE I4 8 8 4 8 1 0 4 8 1 02 11 52 11 5 GND 5 10 10 5 10 11 5 10 11 24 18 24 18 CEO O 61 4 1 461 4 61 4 27 21 27 21 A2 I – – R E A D Y O – – – – 1 5 – – 1 5 – 2 92 32 92 3 SER_EN I 7 17 17 7 17 18 7 17 18 41 35 41 35 VCC 8 2 02 0 8 2 02 0 8 2 02 04 43 84 43 8

AT17LV65/128/256/512/010/002/040 2321E–CNFG–06/03 CE Chip Enable input (active Low). A Low level (with OE High) allows CLK to increment the address counter and enables the data output driver. A High level on CE disables both the address and bit counters and forces the device into a low-power standby mode. Note that this pin will not enable/disable the device in the Two-Wire Serial Programming mode (SER_EN Low). GND Ground pin. A 0.2 µF decoupling capacitor between VCC and GND is recommended. CEO Chip Enable Output (active Low). This output goes Low when the address counter has reached its maximum value. In a daisy chain of AT17LV series devices, the CEO pin of one device must be connected to the CE input of the next device in the chain. It will stay Low as long as CE is Low and OE is High. It will then follow CE until OE goes Low; thereafter, CEO will stay High until the entire EEPROM is read again. A2 Device selection input, A2. This is used to enable (or select) the device during program- ming (i.e., when SER_EN is Low). A2 has an internal pull-down resistor. READY Open collector reset state indicator. Driven Low during power-up reset, released when power-up is complete. It is recommended to use a 4.7 k Ω pull-up resistor when this pin is used. SER_EN Serial enable must be held High during FPGA loading operations. Bringing SER_EN Low enables the Two-Wire Serial Programming Mode. For non-ISP applications, SER_EN should be tied to VCC. VCC 3.3V (±10%) and 5.0V (±5% Commercial, ±10% Industrial) power supply pin.

8 AT17LV65/128/256/512/010/002/040

2321E–CNFG–06/03 FPGA Master Serial Mode Summary The I/O and logic functions of any SRAM-based FPGA are established by a configura- tion program. The program is loaded either automatically upon power-up, or on command, depending on the state of the FPGA mode pins. In Master mode, the FPGA automatically loads the configuration pr ogram from an external memory. The AT17LV Serial Configuration EEPROM has been designed for compatibility with the Master Serial mode. This document discusses the Atmel AT40K, AT40KAL and AT94KAL applications as well as Xilinx applications. Control of Configuration Most connections between the FPGA device and the AT17LV Serial EEPROM are sim- ple and self-explanatory.  The DATA output of the AT17LV series configurator drives DIN of the FPGA devices.  The master FPGA CCLK output drives the CLK input of the AT17LV series configurator. T h e C E O output of any AT17LV series configurator drives the CE input of the next configurator in a cascaded chain of EEPROMs.  SER_EN must be connected to VCC (except during ISP). T h e R E A D Y(1) pin is available as an open-collector indicator of the device’s reset status; it is driven Low while the device is in its power-on reset cycle and released (tri-stated) when the cycle is complete. Note: 1. This pin is not available for the AT17LV65/128/256 devices. Cascading Serial Configuration EEPROMs For multiple FPGAs configured as a daisy-chain, or for FPGAs requiring larger configu- ration memories, cascaded configurators provide additional memory. After the last bit from the first configurator is read, the clock signal to the configurator asserts its CEO output Low and disables its DATA line driver. The second configurator recognizes the Low level on its CE input and enables its DATA output. After configuration is complete, the address counters of all cascaded configurators are reset if the RESET/OE on each configurator is driven to its active (Low) level. If the address counters are not to be reset upon completion, then the RESET /OE input can be tied to its inactive (High) level. AT17LV Series Reset Polarity The AT17LV series configurator allows the user to program the reset polarity as either RESET/OE or RESET/OE. This feature is supported by industry-standard programmer algorithms. Programming Mode The programming mode is entered by bringing SER_EN Low. In this mode the chip can be programmed by the Two-Wire serial bus. The programming is done at V CC supply only. Programming super voltages are generated inside the chip. Standby Mode The AT17LV series configurators enter a low-power standby mode whenever CE is asserted High. In this mode, the AT17LV65/128/256 configurator consumes less than 50 µA of current at 3.3V (100 µA for the AT17LV512/010 and 200 µA for the AT17LV002/040). The output remains in a high-impedance state regardless of the state of the OE input.

AT17LV65/128/256/512/010/002/040 2321E–CNFG–06/03 Absolute Maximum Ratings* Maximum Ratings may cause permanent dam- age to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those listed under oper- ating conditions is not implied. Exposure to Abso- lute Maximum Rating conditions for extended periods of time may affect device reliability. Voltage on Any Pin CC +0.5V Operating Conditions Symbol Description 3.3V 5V UnitsMin Max Min Max VCC Commercial Supply voltage relative to GND -0°C to +70°C 3.0 3.6 4.75 5.25 V Industrial Supply voltage relative to GND -40°C to +85°C 3.0 3.6 4.5 5.5 V

10 AT17LV65/128/256/512/010/002/040

2321E–CNFG–06/03 DC Characteristics VCC = 3.3V ± 10% Symbol Description AT17LV65/ AT17LV128/ AT17LV256 AT17LV512/ AT17LV010 AT17LV002/ AT17LV040 UnitsMin Max Min Max Min Max VIH High-level Input Voltage 2.0 V CC 2.0 V CC 2.0 V CC V VIL Low-level Input Voltage 0 0.8 0 0.8 0 0.8 V VOH High-level Output Voltage (IOH = -2.5 mA) Commercial 2.4 2.4 2.4 V VOL Low-level Output Voltage (IOL = +3 mA) 0.4 0.4 0.4 V VOH High-level Output Voltage (IOH = -2 mA) Industrial 2.4 2.4 2.4 V VOL Low-level Output Voltage (IOL = +3 mA) 0.4 0.4 0.4 V ICCA Supply Current, Active Mode 5 5 5 mA IL Input or Output Leakage Current (V IN = VCC or GND) -10 10 -10 10 -10 10 µA ICCS Supply Current, Standby Mode Commercial 50 100 150 µA Industrial 100 100 150 µA DC Characteristics VCC = 5V ± 5% Commercial; VCC = 5V ± 10% Industrial Symbol Description AT17LV65/ AT17LV128/ AT17LV256 AT17LV512/ AT17LV010 AT17LV002/ AT17LV040 UnitsMin Max Min Max Min Max VIH High-level Input Voltage 2.0 V CC 2.0 V CC 2.0 V CC V VIL Low-level Input Voltage 0 0.8 0 0.8 0 0.8 V VOH High-level Output Voltage (IOH = -2.5 mA) Commercial 3.7 3.86 3.86 V VOL Low-level Output Voltage (IOL = +3 mA) 0.32 0.32 0.32 V VOH High-level Output Voltage (IOH = -2 mA) Industrial 3.6 3.76 3.76 V VOL Low-level Output Voltage (IOL = +3 mA) 0.37 0.37 0.37 V ICCA Supply Current, Active Mode 10 10 10 mA IL Input or Output Leakage Current (V IN = VCC or GND) -10 10 -10 10 -10 10 µA ICCS Supply Current, Standby Mode Commercial 75 200 350 µA Industrial 150 200 350 µA

AT17LV65/128/256/512/010/002/040 2321E–CNFG–06/03 AC Characteristics AC Characteristics when Cascading CE RESET/OE CLK DATA TSCE TLC THC TCACTOE TCE TOH THOE TSCE THCE TDF TOH CE RESET/OE CLK DATA CEO TCDF TOCK TOCE TOCE TOOE LAST BIT FIRST BIT

12 AT17LV65/128/256/512/010/002/040

2321E–CNFG–06/03 Notes: 1. AC test lead = 50 pF . 2. Float delays are measured with 5 pF AC loads. Transition is measured ± 200 mV from steady-state active levels. Notes: 1. AC test lead = 50 pF . 2. Float delays are measured with 5 pF AC loads. Transition is measured ± 200 mV from steady-state active levels. AC Characteristics VCC = 3.3V ± 10% Symbol Description AT17LV65/128/256 AT17LV512/010/002/040 Units Commercial Industrial Commercial Industrial M i nM a xM i nM a xM i nM a xM i nM a x TOE (1) OE to Data Delay 50 55 50 55 ns TCE (1) CE to Data Delay 60 60 55 60 ns TCAC (1) CLK to Data Delay 75 80 55 60 ns TOH Data Hold from CE, O E , o r C L K 0000 n s TDF (2) CE or OE to Data Float Delay 55 55 50 50 ns TLC CLK Low Time 25 25 25 25 ns THC CLK High Time 25 25 25 25 ns TSCE CE Setup Time to CLK (to guarantee proper counting) 35 60 30 35 ns THCE CE Hold Time from CLK (to guarantee proper counting) 0000 n s THOE OE High Time (guarantees counter is reset) 25 25 25 25 ns FMAX Maximum Clock Frequency 10 10 15 10 MHz AC Characteristics when Cascading VCC = 3.3V ± 10% Symbol Description AT17LV65/128/256 AT17LV512/010/002/040 Units Commercial Industrial Commercial Industrial Min Max Min Max Min Max Min Max TCDF (2) CLK to Data Float Delay 60 60 50 50 ns TOCK (1) CLK to CEO Delay 55 60 50 55 ns TOCE (1) CE to CEO Delay 55 60 35 40 ns TOOE (1) RESET/OE to CEO Delay 40 45 35 35 ns FMAX Maximum Clock Frequency 8 8 12.5 10 MHz

AT17LV65/128/256/512/010/002/040 2321E–CNFG–06/03 Notes: 1. AC test lead = 50 pF . 2. Float delays are measured with 5 pF AC loads. Transition is measured ± 200 mV from steady-state active levels. Notes: 1. AC test lead = 50 pF . 2. Float delays are measured with 5 pF AC loads. Transition is measured ± 200 mV from steady-state active levels. AC Characteristics VCC = 5V ± 5% Commercial; VCC = 5V ± 10% Industrial Symbol Description AT17LV65/128/256 AT17LV512/010/002/040 Units Commercial Industrial Commercial Industrial M i nM a xM i nM a xM i nM a xM i nM a x TOE (1) OE to Data Delay 30 35 30 35 ns TCE (1) CE to Data Delay 45 45 45 45 ns TCAC (1) CLK to Data Delay 50 55 50 50 ns TOH Data Hold from CE, OE, or CLK 0 0 0 0 ns TDF (2) CE or OE to Data Float Delay 50 50 50 50 ns TLC CLK Low Time 20 20 20 20 ns THC CLK High Time 20 20 20 20 ns TSCE CE Setup Time to CLK (to guarantee proper counting) 35 40 20 25 ns THCE CE Hold Time from CLK (to guarantee proper counting) 0000 n s THOE OE High Time (guarantees counter is reset) 20 20 20 20 ns FMAX Maximum Clock Frequency 12.5 12.5 15 15 MHz AC Characteristics when Cascading VCC = 5V ± 5% Commercial; VCC = 5V ± 10% Industrial Symbol Description AT17LV65/128/256 AT17LV512/010/002/040 Units Commercial Industrial Commercial Industrial M i nM a xM i nM a xM i nM a xM i nM a x TCDF (2) CLK to Data Float Delay 50 50 50 50 ns TOCK (1) CLK to CEO Delay 35 40 35 40 ns TOCE (1) CE to CEO Delay 35 35 35 35 ns TOOE (1) RESET/OE to CEO Delay 30 35 30 30 ns FMAX Maximum Clock Frequency 10 10 12.5 12.5 MHz

14 AT17LV65/128/256/512/010/002/040

2321E–CNFG–06/03 Notes: 1. For more information refer to the “Thermal Characteristics of Atmel’s Packages”, available on the Atmel web site. 2. Airflow = 0 ft/min. Thermal Resistance Coefficients(1) Package Type AT17LV65/ AT17LV128/ AT17LV256 AT17LV512/ AT17LV010 AT17LV002 AT17LV040 8CN4 Leadless Array Package (LAP) θJC [°C/W] 45 45 45 – 8P3 Plastic Dual Inline Package (PDIP) θJC [°C/W] 37 37 – – 8S1 Plastic Gull Wing Small Outline (SOIC) 20J Plastic Leaded Chip Carrier (PLCC) θJC [°C/W] 35 35 35 – 20S2 Plastic Gull Wing Small Outline (SOIC) θJC [°C/W] – θJA °C/W – 44A Thin Plastic Quad Flat Package (TQFP) θJC [°C/W] – – 17 17 44J Plastic Leaded Chip Carrier (PLCC) θJC [°C/W] – – 15 15

Figure 1. Ordering Code

16 AT17LV65/128/256/512/010/002/040

2321E–CNFG–06/03 Note: 1. For operating 5V operating voltage, please refer to the corresponding AC and DC Characteristics.

Ordering Information

Memory Size Ordering Code Package Operation Range 64-Kbit(1) AT17LV65-10CC AT17LV65-10PC AT17LV65-10NC AT17LV65-10JC AT17LV65-10SC 8CN4 8P3 8S1 20J 20S2 Commercial (0°C to 70°C) AT17LV65-10CI AT17LV65-10PI AT17LV65-10NI AT17LV65-10JI AT17LV65-10SI 8CN4 8P3 8S1 20J 20S2 Industrial (-40°C to 85°C) 128-Kbit (1) AT17LV128-10CC AT17LV128-10PC AT17LV128-10NC AT17LV128-10JC AT17LV128-10SC 8CN4 8P3 8S1 20J 20S2 Commercial (0°C to 70°C) AT17LV128-10CI AT17LV128-10PI AT17LV128-10NI AT17LV128-10JI AT17LV128-10SI 8CN4 8P3 8S1 20J 20S2 Industrial (-40°C to 85°C) 256-Kbit (1) AT17LV256-10CC AT17LV256-10PC AT17LV256-10NC AT17LV256-10JC AT17LV256-10SC 8CN4 8P3 8S1 20J 20S2 Commercial (0°C to 70°C) AT17LV256-10CI AT17LV256-10PI AT17LV256-10NI AT17LV256-10JI AT17LV256-10SI 8CN4 8P3 8S1 20J 20S2 Industrial (-40°C to 85°C) 512-Kbit (1) AT17LV512-10CC AT17LV512-10PC AT17LV512-10JC AT17LV512-10SC 8CN4 8P3 20J 20S2 Commercial (0°C to 70°C) AT17LV512-10CI AT17LV512-10PI AT17LV512-10JI AT17LV512-10SI 8CN4 8P3 20J 20S2 Industrial (-40°C to 85°C) 1-Mbit (1) AT17LV010-10CC AT17LV010-10PC AT17LV010-10JC AT17LV010-10SC 8CN4 8P3 20J 20S2 Commercial (0°C to 70°C) AT17LV010-10CI AT17LV010-10PI AT17LV010-10JI AT17LV010-10SI 8CN4 8P3 20J 20S2 Industrial (-40°C to 85°C) 2-Mbit (1) AT17LV002-10CC AT17LV002-10JC AT17LV002-10SC AT17LV002-10TQC AT17LV002-10BJC 8CN4 20J 20S2 44A 44J Commercial (0°C to 70°C) AT17LV002-10CI AT17LV002-10JI AT17LV002-10SI AT17LV002-10TQI AT17LV002-10BJI 8CN4 20J 20S2 44A 44J Industrial (-40°C to 85°C) 4-Mbit (1) AT17LV040-10TQC AT17LV040-10BJC 44A 44J Commercial (0°C to 70°C) AT17LV040-10TQI AT17LV040-10BJI 44A 44J Industrial (-40°C to 85°C)

AT17LV65/128/256/512/010/002/040 2321E–CNFG–06/03 Packaging Information 8CN4 – LAP

2325 Orchard Parkway

San Jose, CA 95131 TITLE DRAWING NO. R REV. 8CN4, 8-lead (6 x 6 x 1.04 mm Body), Lead Pitch 1.27 mm, Leadless Array Package (LAP) A8CN4 11/14/01 Pin1 Corner Marked Pin1 Indentifier 0.10 mm TYP Top View L b e Side View A Bottom View E D COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A 0.94 1.04 1.14 A1 0.30 0.34 0.38 b 0.45 0.50 0.55 1 D 5.89 5.99 6.09 E 4.89 5.99 6.09 e 1.27 BSC e1 1.10 REF L 0.95 1.00 1.05 1 L1 1.25 1.30 1.35 1 Note: 1. Metal Pad Dimensions.

18 AT17LV65/128/256/512/010/002/040

2321E–CNFG–06/03 8P3 – PDIP San Jose, CA 95131 TITLE DRAWING NO. R REV. 8P3, 8-lead, 0.300" Wide Body, Plastic Dual In-line Package (PDIP) 01/09/02 8P3 B D E e Lb2 b A2 A N eA c

4 PLCS

(Unit of Measure = inches) SYMBOL MIN NOM MAX NOTE Notes: 1. This drawing is for general information only; refer to JEDEC Drawing MS-001, Variation BA for additional information. 2. Dimensions A and L are measured with the package seated in JEDEC seating plane Gauge GS-3. 3. D, D1 and E1 dimensions do not include mold Flash or protrusions. Mold Flash or protrusions shall not exceed 0.010 inch. 4. E and eA measured with the leads constrained to be perpendicular to datum. 5. Pointed or rounded lead tips are preferred to ease insertion. A 0.210 2 A2 0.115 0.130 0.195 b 0.014 0.018 0.022 5 b2 0.045 0.060 0.070 6 b3 0.030 0.039 0.045 6 c 0.008 0.010 0.014 D 0.355 0.365 0.400 3 D1 0.005 3 E 0.300 0.310 0.325 4 E1 0.240 0.250 0.280 3 e 0.100 BSC eA 0.300 BSC 4 L 0.115 0.130 0.150 2

AT17LV65/128/256/512/010/002/040 2321E–CNFG–06/03 8S1 – SOIC San Jose, CA 95131 TITLE DRAWING NO. R REV. Note: 10/10/01 8S1, 8-lead (0.150" Wide Body), Plastic Gull Wing Small Outline (JEDEC SOIC) 8S1 A H N Top View C E End View A B L e D Side View COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE This drawing is for general information only. Refer to JEDEC Drawing MS-012 for proper dimensions, tolerances, datums, etc. A – – 1.75 B – – 0.51 C – – 0.25 D – – 5.00 E – – 4.00 e 1.27 BSC H – – 6.20 L – – 1.27

20 AT17LV65/128/256/512/010/002/040

2321E–CNFG–06/03 20J – PLCC San Jose, CA 95131R TITLE DRAWING NO. REV. Notes: 1. This package conforms to JEDEC reference MS-018, Variation AA. 2. Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is .010"(0.254 mm) per side. Dimension D1 and E1 include mold mismatch and are measured at the extreme material condition at the upper or lower parting line. 3. Lead coplanarity is 0.004" (0.102 mm) maximum. A 4.191 – 4.572 A1 2.286 – 3.048 A2 0.508 – – D 9.779 – 10.033 D1 8.890 – 9.042 Note 2 E 9.779 – 10.033 E1 8.890 – 9.042 Note 2 D2/E2 7.366 – 8.382 B 0.660 – 0.813 B1 0.330 – 0.533 e 1.270 TYP COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE 1.14(0.045) X 45˚ PIN NO. 1 IDENTIFIER 1.14(0.045) X 45˚ 0.51(0.020)MAX 0.318(0.0125) 0.191(0.0075) 45˚ MAX (3X) A D2/E2 B e E1 E D 20J, 20-lead, Plastic J-leaded Chip Carrier (PLCC) B20J 10/04/01

AT17LV65/128/256/512/010/002/040 2321E–CNFG–06/03 20S2 – SOIC San Jose, CA 95131 TITLE DRAWING NO. R REV. 20S2, 20-lead, 0.300" Wide Body, Plastic Gull Wing Small Outline Package (SOIC) 1/9/02 20S2 A L End View Side View Top View HE b N e A D C COMMON DIMENSIONS (Unit of Measure = inches) SYMBOL MIN NOM MAX NOTE Notes: 1. This drawing is for general information only; refer to JEDEC Drawing MS-013, Variation AC for additional information. 2. Dimension "D" does not include mold Flash, protrusions or gate burrs. Mold Flash, protrusions and gate burrs shall not exceed 0.15 mm (0.006") per side. 3. Dimension "E" does not include inter-lead Flash or protrusion. Inter-lead Flash and protrusions shall not exceed 0.25 mm (0.010") per side. 4. "L" is the length of the terminal for soldering to a substrate. 5. The lead width "b", as measured 0.36 mm (0.014") or greater above the seating plane, shall not exceed a maximum value of 0.61 mm (0.024") per side. A 0.0926 0.1043 A1 0.0040 0.0118 b 0.0130 0.0200 4 C 0.0091 0.0125 D 0.4961 0.5118 1 E 0.2914 0.2992 2 H 0.3940 0.4190 L 0.0160 0.050 3 e 0.050 BSC

22 AT17LV65/128/256/512/010/002/040

2321E–CNFG–06/03 44A – TQFP San Jose, CA 95131 TITLE DRAWING NO. R REV. 44A, 44-lead, 10 x 10 mm Body Size, 1.0 mm Body Thickness, 0.8 mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP) B44A 10/5/2001 PIN 1 IDENTIFIER 0˚~7˚ PIN 1 L C A1 A2 A D e E1 E B COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE Notes: 1. This package conforms to JEDEC reference MS-026, Variation ACB. 2. Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is 0.25 mm per side. Dimensions D1 and E1 are maximum plastic body size dimensions including mold mismatch. 3. Lead coplanarity is 0.10 mm maximum. A – – 1.20 A1 0.05 – 0.15 A2 0.95 1.00 1.05 D 11.75 12.00 12.25 D1 9.90 10.00 10.10 Note 2 E 11.75 12.00 12.25 E1 9.90 10.00 10.10 Note 2 B 0.30 – 0.45 C 0.09 – 0.20 L 0.45 – 0.75 e 0.80 TYP

AT17LV65/128/256/512/010/002/040 2321E–CNFG–06/03 44J – PLCC Notes: 1. This package conforms to JEDEC reference MS-018, Variation AC. 2. Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is .010"(0.254 mm) per side. Dimension D1 and E1 include mold mismatch and are measured at the extreme material condition at the upper or lower parting line. 3. Lead coplanarity is 0.004" (0.102 mm) maximum. A 4.191 – 4.572 A1 2.286 – 3.048 A2 0.508 – – D 17.399 – 17.653 D1 16.510 – 16.662 Note 2 E 17.399 – 17.653 E1 16.510 – 16.662 Note 2 D2/E2 14.986 – 16.002 B 0.660 – 0.813 B1 0.330 – 0.533 e 1.270 TYP COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE 1.14(0.045) X 45˚ PIN NO. 1 IDENTIFIER 1.14(0.045) X 45˚ 0.51(0.020)MAX 0.318(0.0125) 0.191(0.0075) 45˚ MAX (3X) A B1 D2/E2 B e E1 E D 44J, 44-lead, Plastic J-leaded Chip Carrier (PLCC) B44J 10/04/01 San Jose, CA 95131 TITLE DRAWING NO. R REV.

Printed on recycled paper. Disclaimer: Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company’s standar d warranty which is detailed in Atmel’s Terms and Conditions located on the Company’s web site. The Company assumes no responsibi lity for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time wi thout notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Atmel are granted by the Company in connection with the sale of Atmel products , expressly or by implication. Atmel’s products are not aut horized for use as critical components in life support devices or systems. Atmel Corporation Atmel Operations San Jose, CA 95131 Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Regional Headquarters Europe Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland Tel: (41) 26-426-5555 Fax: (41) 26-426-5500 Asia Room 1219 Chinachem Golden Plaza

77 Mody Road Tsimshatsui

Tel: (852) 2721-9778 Fax: (852) 2722-1369 Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Memory San Jose, CA 95131 Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 Microcontrollers San Jose, CA 95131 Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 La Chantrerie BP 70602

44306 Nantes Cedex 3, France

13106 Rousset Cedex, France

1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland Tel: (44) 1355-803-000 Fax: (44) 1355-242-743 RF/Automotive Theresienstrasse 2 Postfach 3535

74025 Heilbronn, Germany

1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom Avenue de Rochepleine BP 123

38521 Saint-Egreve Cedex, France

Atmel Configurator Hotline (408) 436-4119 Atmel Configurator e-mail configurator@atmel.com FAQ Available on web site e-mail literature@atmel.com Web Site http://www.atmel.com 2321E–CNFG–06/03 xM © Atmel Corporation 2003 . All rights reserved. Atmel ® and combinations thereof are the registered trade- mark of Atmel. FLEX ™ is the trademark of Altera Corporation; ORCA ™ is the trademark of Lattice Semiconductors; SPARTAN® and Virtex ® are the registered trademarks of Xilinx, Inc.; XC3000 ™ , XC4000 ™ and XC5200 ™ are the trademarks of Xilinx, Inc.; APEX ™ is the trademark of MIPS Technologies; Other terms and product names may be the trademarks of others.