AT17C512 ATMEL
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 9
Technical content
Features
- E2 Programmable 524,288 x 1 and 1,048,576 x 1 bit Serial Memories Designed To Store Configuration Programs For Field Programmable Gate Arrays (FPGA)
- Simple Interface to SRAM FPGAs
- Compatible With Atmel AT6000, AT40K FPGAs, Altera EPF8K, EPF10K, EPF6K FPGAs, ORCA FPGAs, Xilinx XC3000, XC4000, XC5200 FPGAs, Motorola MPA1000 FPGAs
- Cascadable To Support Additional Configurations or Future Higher-density Arrays
- Low-power CMOS EEPROM Process
- Programmable Reset Polarity
- Available In PLCC Package (Pin Compatable across Product Family)
- In-System Programmable Via 2-Wire Bus
- Emulation of 24CXX Serial EPROMs
- Available in 3.3V ± 10% L V and 5V Versions
- System Friendly READY Pin
Description
The AT17C512/010 and AT17LV512/010 (high-density AT17 Series) FPGA Configu- ration EEPROMs (Configurators) provide an easy-to-use, cost-effective configuration memory for Field Programmable Gate Arrays. The high-density AT17 Series is pack- aged in the popular 20-pin PLCC. The high-density AT17 Series family uses a simple serial-access procedure to configure one or more FPGA devices. The high-density AT17 Series organization supplies enough memory to configure one or multiple smaller FPGAs. The user can select the polarity of the reset function by programming one EEPROM byte. The devices also support a write protection mode and a system friendly READY pin, which signifies a “good” power level to the device and can be used to ensure reliable system power-up. The high-density AT17 Series can be programmed with industry-standard program- mers, and the Atmel ATDH2200 Programming board. FPGA Configuration E 2PROM Memory 512K and 1M AT17C512 AT17LV512 AT17C010 AT17LV010 Rev. 0944A-A–12/97 Pin Configurations 20-Pin PLCC RESET/OE CE 3 2 1 20 19 CLK D A T A V C C N C N C N C READY NC WP2 NC WP1 N C N C N C N C SER_EN CEO G N D
Controlling The High-Density AT17 Series Serial EEPROMs Most connections between the FPGA device and the Serial EEPROM are simple and self-explanatory:
- The DA T A output of the high-density A T17 Series drives DIN of the FPGA devices.
- The master FPGA CCLK output drives the CLK input of the high-density A T17 Series.
- The CEO output of any A T17C/LV512/010 drives the CE input of the next A T17C/LV512/010 in a cascade chain of PROMs.
- S E R _ E N must be connected to VCC , (except during ISP). READY is available as an open-collector indicator of the device’s RESET status; it is driven Low while the device is in its POWER-ON RESET cycle and released (tri-stated) when the cycle is complete. There are two different ways to use the inputs CE and OE, as shown in the AC Characteristics waveforms. Condition 1 The simplest connection is to have the FPGA D/P output drive both CE and RESET/OE in parallel (Figure 1). Due to its simplicity, however, this method will fail if the FPGA receives an external reset condition during the configura- tion cycle. If a system reset is applied to the FPGA, it will abort the original configuration and then reset itself for a new configuration, as intended. Of course, the high-density AT17 Series does not see the external reset signal and will not reset its internal address counters and, consequently, will remain out of sync with the FPGA for the remainder of the configuration cycle. Condition 2 The FPGA D/P output drives only the CE input of the high- density AT17 Series, while its OE input is driven by the inversion of the input to the FPGA RESET input pin. This connection works under all normal circumstances, even when the user aborts a configuration before D/P has gone High. A High level on the RESET/OE input to the AT17C/LVxxx – during FPGA reset – clears the Configura- tor’s internal address pointer, so that the reconfiguration starts at the beginning. The high-density AT17 Series does not require an inverter since the RESET polarity is pro- grammable. Block Diagram
2 DA T A I/O Three-state DA T A output for reading. Input/Output pin for programming. 4 CLK I Clock input. Used to increment the internal address and bit counter for reading and programming. 5 WP1 I WRITE PROTECT (1). Used to protect portions of memory during programming. See programming guide for details.
6 RESET/OE
I RESET/Output Enable input (when SER_EN is High). A Low level on both the CE and RESET/OE inputs enables the data output driver. A High level on RESET/OE resets both the address and bit counters. The logic polarity of this input is programmable as either RESET/OE or RESET/OE. This document describes the pin as RESET/OE. 7 WP2 I WRITE PROTECT (2). Used to protect portions of memory during programming. See programming guide for details. 8C E I Chip Enable input. Used for device selection. A Low level on both CE and OE enables the data output driver. A High level on CE disables both the address and bit counters and forces the device into a low power mode. Note this pin will not enable/disable the device in 2-wire Serial Programming mode (i.e., when SER_EN is Low). 10 GND Ground pin. 14 CEO O Chip Enable Out output. This signal is asserted Low on the clock cycle following the last bit read from the memory. It will stay Low as long as CE and OE are both Low. It will then follow CE until OE goes High. Thereafter, CEO will stay High until the entire PROM is read again and senses the status of RESET polarity. A2 I Device selection input, A2. This is used to enable (or select) the device during programming, when SER_EN is Low (see Programming Guide for more details) 15 READY O Open collector reset state indicator. Driven Low during power-up reset, released when power- up is complete. (Recommend a 4.7KΩ Pull-up on this pin if used). 17 SER_EN I Serial enable is normally high during FPGA loading operations. Bringing SER_EN Low, enables the two wire serial interface mode for programming. 20 V CC +3.3V/+5V power supply pin. Absolute Maximum Ratings* mum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other condi- tions beyond those listed under Operating Conditions is not implied. Exposure to Absolute Maximum Rat- ings conditions for extended periods of time may affect device reliability. Voltage on Any Pin CC + 0.5V ESD (R
designed for compatibility with the Master Serial Mode. caded Configurators provide additional memory. Figure 1. Condition 1 Connection tion. The AT17C Series parts are read/write at 5V nominal. The AT17LV parts are read/write at 3.3V nominal.
VCC = 5V ± 5% Commercial / 5V ± 10% Ind./Mil. Symbol Description Min Max Units VIH High-level input voltage 2.0 V CC V VIL Low-level input voltage 0 0.8 V VOH High-level output voltage (IOH = -4 mA) Commercial 3.86 V VOL Low-level output voltage (IOL = +4 mA) 0.32 V VOH High-level output voltage (IOH = -4 mA) Industrial 3.76 V VOL Low-level output voltage (IOL = +4 mA) 0.37 V VOH High-level output voltage (IOH = -4 mA) Military 3.7 V VOL Low-level output voltage (IOL = +4 mA) 0.4 V ICCA Supply current, active mode (at FMAX) 10 mA IL Input or output leakage current (VIN = VCC or GND) -10 10 µA ICCS Supply current, standby mode Commercial 0.5 mA Industrial/Military 0.5 mA DC Characteristics VCC = 3.3V ± 10% Symbol Description Min Max Units VIH High-level input voltage 2.0 V CC V VIL Low-level input voltage 0 0.8 V VOH High-level output voltage (IOH = -2.5 mA) Commercial 2.4 V VOL Low-level output voltage (IOL = +3 mA) 0.4 V VOH High-level output voltage (IOH = -2 mA) Industrial 2.4 V VOL Low-level output voltage (IOL = +3 mA) 0.4 V VOH High-level output voltage (IOH = -2 mA) Military 2.4 V VOL Low-level output voltage (IOL = +2.5 mA) 0.4 V ICCA Supply current, active mode 5 mA IL Input or output leakage current (VIN = VCC or GND) -10 10 µA ICCS Supply current, standby mode Commercial 100 µA Industrial/Military 100 µA
AC Characteristics When Cascading
Notes: 1. Preliminary specifications for military operating range only. 2. AC test load = 50 pF . 3. Float delays are measured with 5 pF AC loads. Transition is measured ± 200 mV from steady state active levels. AC Characteristics for AT17C512/010 VCC = 5V ± 5% Commercial / VCC = 5V ± 10% Ind./Mil Symbol Description Commercial/Industrial Military UnitsMin Max Min Max TOE (2) OE to Data Delay 30 35 ns TCE (2) CE to Data Delay 45 45 ns TCAC (2) CLK to Data Delay 50 50 ns TOH (2) Data Hold From CE, OE, or CLK 0 0 ns TDF (3) CE or OE to Data Float Delay 50 50 ns TLC CLK Low Time 20 20 ns THC CLK High Time 20 20 ns TSCE CE Setup Time to CLK (to guarantee proper counting) 20 25 ns THCE CE Hold Time to CLK (to guarantee proper counting) 0 0 ns THOE OE High Time (Guarantees Counter Is Reset) 20 20 ns FMAX MAX Input Clock Frequency 15 15 MHz VRDY Ready Pin Open Collector Voltage 1.2 2.2 1.2 2.2 V AC Characteristics for AT17C512/010 When Cascading VCC = 5V± 5% Commercial / VCC = 5V ± 10% Ind./Mil. Symbol Description Commercial/Industrial Military UnitsM i nM a xM i nM a x TCDF (3) CLK to Data Float Delay 50 50 ns TOCK (2) CLK to CEO Delay 35 40 ns TOCE (2) CE to CEO Delay 35 35 ns TOOE (2) RESET/OE to CEO Delay 30 30 ns
Notes: 1. Preliminary specifications for military operating range only. 2. AC test load = 50 pF . 3. Float delays are measured with 5 pF AC loads. T ransition is measured ± 200 mV from steady state active levels. 4. During cascade FMAX = 12.5 MHz. AC Characteristics for AT17LV512/010 VCC = 3.3V ± 10% Symbol Description Commercial/Industrial Military UnitsMin Max Min Max TOE (2) OE to Data Delay 50 55 ns TCE (2) CE to Data Delay 55 60 ns TCAC (2) CLK to Data Delay 55 60 ns TOH Data Hold From CE, OE, or CLK 0 0 ns TDF (3) CE or OE to Data Float Delay 50 50 ns TLC CLK Low Time 25 25 ns THC CLK High Time 25 25 ns TSCE CE Setup Time to CLK (to guarantee proper counting) 30 35 ns THCE CE Hold Time to CLK (to guarantee proper counting) 0 0 ns THOE OE High Time (Guarantees Counter Is Reset) 25 25 ns FMAX (4) MAX Input Clock Frequency 15 10 MHz VRDY Ready Pin Open Collector Voltage 1.2 2.2 1.2 2.2 V AC Characteristics for AT17LV512/010 When Cascading VCC = 3.3V ± 10% Symbol Description Commercial/Industrial Military UnitsM i nM a xM i nM a x TCDF (3) CLK to Data Float Delay 50 50 ns TOCK (2) CLK to CEO Delay 50 55 ns TOCE (2) CE to CEO Delay 35 40 ns TOOE (2) RESET/OE to CEO Delay 35 35 ns
Ordering Information - 5V Devices Memory Size Ordering Code Package Operation Range 512K A T17C512-10JC 20J Commercial (0°C to 70°C) A T17C512-10JI 20J Industrial (-40°C to 85°C) 1M A T17C010-10JC 20J Commercial (0°C to 70°C) A T17C010-10JI 20J Industrial (-40°C to 85°C) Ordering Information - 3.3V Devices Memory Size Ordering Code Package Operation Range 512K A T17L V512-10JC 20J Commercial (0°C to 70°C) A T17L V512-10JI 20J Industrial (-40°C to 85°C) 1M A T17L V010-10JC 20J Commercial (0°C to 70°C) A T17L V010-10JI 20J Industrial (-40°C to 85°C) Package Type 20J 20 Lead, Plastic J-Leaded Chip Carrier (PLCC)