AT-220 MACOM

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 6

Technical content

Features

Attenuation 2-dB Steps to 30 dB High Accuracy +/-3% Temperature Stability +/-0.15 dB from -40°C to +85°C Low Intermodulation Product: +50 dBm IP3 Low DC Power Consumption: 50 mW Low Cost SOIC 16 Plastic Package Tape and Reel Packaging Available1

Description

M/A-COM’s AT-220 is a 4-bit, 2-dB step GaAs MMIC digital attenuator in a low cost SOIC 16-lead surface mount plastic package. The AT-220 is ideally suited for use where high accuracy, fast switching, very low power consumption and low intermodulation products are required. Typical applications include radio and cellular equipment, wireless LANs, GPS equipment and other Gain/Level Control circuits. The AT-220 is fabricated with a monolithic GaAs MMIC using a mature 1-micron process. The process features full chip passivation for increased performance and reliability. SO-16 .013-.020 TYP (0.33-0.51) .0040-.0098 (0.10-0.25) .2284-.2440 (5.80-6.20) Pin #16 Orientation Mark .010(0.25) M B M .1497-.1574 (3.80-4.00) -B- 0.3859-0.3937 (9.80-10.00) -A- 0.050(1.27) BSC. .0532-.0688 (1.35-1.75) .010(0.25) M C A M B S 16-Lead SOP outline dimensions Narrow body .150 (All dimensions per JEDEC No. MS-012-AC, Issue C) Dimensions in ( ) are in mm. 0°-8° .0099-.0196 x 45° Chamfer (0.25-0.50) .016-.050 (0.40-1.27) .0075-.0098 (0.19-0.25) -C- Pin #1 Unless Otherwise Noted: .xxx = ± 0.010 (.xx = ± 0.25) .004 (0.10) Part Number Package AT-220 PIN SOIC 16-Lead Plastic Package AT-220TR Forward Tape & Reel AT-220RTR Reverse Tape & Reel

Ordering Information

Parameter Test Conditions 2 Unit Min. Typ. Max Reference Insertion Loss DC – 0.1 GHz dB 1.2 1.4 DC – 0.1 GHz dB 1.5 1.7 DC – 1.0 GHz dB 1.6 1.8 DC – 2.0 GHz dB 1.8 2.1 Attenuation Accuracy3 DC – 1.0 GHz ±(0.15 dB + 3% of Attenuation Setting in dB) dB DC – 2.0 GHz ±(0.30 dB + 3% of Attenuation Setting in dB) dB VSWR 1.2:1 Trise, Tfall 10% to 90% RF, 90% to 10% RF nS 12 Ton, Toff 50% Control to 90% RF, 50% Control to 10% RF nS 18 Transients In Band mV 25 1 dB Input Power 0.05 GHz dBm 20 Compression Input Power 0.5 – 2.0 GHz dBm 28 Measured Relative 0.05 GHz dBm 45 IP2 to Input Power 0.5 – 2.0 GHz dBm 68 (For two-tone Input Power Up to +5 dBm) Measured Relative 0.05 GHz dBm 40 IP3 to Input Power 0.5 – 2.0 GHz dBm 50 (For two-tone Input Power Up to +5 dBm) Electrical Specifications, TA = 25°C 1. Refer to “Tape and Reel Packaging” Section, or contact factory. 2. All measurements at 1 GHz in a 50Ω system, unless otherwise specified. 3. Attenuation accuracy specifications apply with negative bias control and low inductance grounding. AT-220 11/15/96 1:49 PM Page 1 (Black plate)

Digital Attenuator, 30 dB, 4-Bit AT-220 V3.00 M/A-COM, Inc. North America: Tel. (800) 366-2266 n Asia/Pacific: Tel. +81 3 3263 8761 n Europe: Tel. +44 (1344) 869 595 Fax (800) 618-8883 Fax +81 3 3263 8769 Fax +44 (1344) 300 020 Specifications Subject to Change Without Notice. Functional SchematicAbsolute Maximum Ratings1 1. Operation of this device above any one of these parameters may cause permanent damage. Parameter Absolute Maximum Max. Input Power

50 MHz +27 dBm

Control Voltage +5V, -8.5V Operating Temperature -40°C to +85°C Storage Temperature -65°C to +150°C Typical Performance Pin Configuration INSERTION LOSS vs FREQUENCY LOSS (dB) FREQUENCY (GHz) 0 0.5 1.0 1.5 2.0 3.0 2.0 1.0 + 85˚C + 25˚C - 40˚C 2.0 VSWR vs FREQUENCY 1.8 0 0.5 1.6 1.0 1.0 1.5 2.0 FREQUENCY (GHz) VSWR1.4 1.2 4 dB ATTEN 8 dB ATTEN 2 dB ATTEN 16 dB ATTEN INSERTION LOSS -10 -12 -14 -16 -18 -20 -22 -24 -26 -28 -30 -32 ATTENUATION vs FREQUENCY LOSS (dB) FREQUENCY (GHz) 1.5 ATTENUATION ACCURACY vs FREQUENCY 0.0 0.5 -0.5 -1.5 1.0 1.5 2.0 DEVIATION FROM NOMINAL ATTENUATION (dB) 0.5 FREQUENCY (GHz) 4 dB ATTEN 2 dB ATTEN 16 dB ATTEN 8 dB ATTEN 30 dB ATTEN Pin Description Pin No. Description

1 VC1 9 RF2

2 VC1 10 GND

3 VC2 11 GND

4 VC2 12 GND

5 VC3 13 GND

6 VC3 14 GND

7 VC4 15 GND

8 VC4 16 RF1

VC4 VC4 VC3 VC3 VC2 VC2 VC1 VC1 Attenuation (dB) 1 0 1 0 1 0 1 0 Reference 01 101 010 2 d B 10 011 010 4 d B 10 100 110 8 d B 1 0 1 0 1 0 0 1 16 dB 0 1 0 1 0 1 0 1 30 dB "0" = Vin Low, Vin Low = 0V, "1" = Vin High, Vin High = -5V "0" = 0 to -0.2V @ 20mA Max "1" = -5V @ 10 mA typ to -8V @ 200 mA Max 321 0 RF1 GNDGND GND GND GND RF2GND VC1 VC1 VC2 VC3 VC3 VC4 VC4VC2 8 dB 4 dB 2 dB 1 dB 16 15 14 13 12 11 10 9 87654321 Truth Table AT-220 11/15/96 1:49 PM Page 2 (Black plate)

Digital Attenuator, 30 dB, 4-Bit AT-220 M/A-COM, Inc. North America: Tel. (800) 366-2266 n Asia/Pacific: Tel. +81 3 3263 8761 n Europe: Tel. +44 (1344) 869 595 Fax (800) 618-8883 Fax +81 3 3263 8769 Fax +44 (1344) 300 020 Specifications Subject to Change Without Notice. V3.00 FREQUENCY (GHz) ATTENUATION (dB) 0 0.2 0.4 0.6 0.8 1 ATTENUATION vs FREQUENCY FREQUENCY (GHz) S11 (dB) -10 -15 -20 -25 -30 0 0.2 0.4 0.6 0.8 1 S11 vs FREQUENCY 0 dB 2 dB 8 dB 4 dB 16 dB 30 dB Swept Data Characterized in 75 Ohms AT-220 11/15/96 1:49 PM Page 3 (Black plate)

AT-220 11/15/96 1:49 PM Page 3 (Cyan plate)

AT-220 11/15/96 1:49 PM Page 3 (Magenta plate)

AT-220 11/15/96 1:49 PM Page 3 (Yellow plate)