APW7134 KINGBRIGHT
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 16
Technical content
Copyright ANPEC Electronics Corp. Rev. A.1 - Aug., 2006 APW7134 www.anpec.com.tw1 ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and advise customers to obtain the latest version of relevant information to verify before placing orders. Dual 1.5MHz, 600mA Synchronous Step-Down Converter Features General Description
Applications
- TV Tuner/Box
- Portable Instrument The APW7134 contains two independent 1.5MHz con- stant frequency, current mode, PWM step-down converters. Each converter integrates a main switch and a synchronous rectifier for high efficiency without an external Schottky diode. The APW7134 is ideal for powering portable equipment that runs from a single
- 600mA Output Current on Each Channel
- 2.5V to 5.5V Input Voltage Range
- 1.5MHz Constant Frequency Operation
- Low Dropout Operation at 100% Duty Cycle
- Synchronous Topology
- 0.6V Low Reference Voltage
- Typically 0.1 µA Shutdown Current
- Current Mode Operation
- Over Temperature Protection
- Over Current Protection
- Up to 94% Efficiency
- Internally Compensated
- Lead Free Available (RoHS Compliant) cell Lithium-Ion (Li+) battery. Each converter can sup- ply 600mA of load current from a 2.5V to 5.5V input voltage. The output voltage can be regulated as low as 0.6V. The APW7134 can also run at 100% duty cycle for low dropout applications. Pinouts 10EN1 SW1 GND1 IN1 FB2 EN2SW2 GND2 IN2 FB1 Exposed pad on backside APW7134 (Top View) DFN-10 (3mm x 3mm)
Copyright ANPEC Electronics Corp. Rev. A.1 - Aug., 2006 APW7134 www.anpec.com.tw2 Ordering and Marking Information Note: ANPEC lead-free products contain molding compounds/die attach materials and 100% matte tin plate termination finish; which are fully compliant with RoHS and compatible with both SnPb and lead-free soldiering operations. ANPEC lead-free products meet or exceed the lead-free requirements of IPC/JEDEC J STD-020C for MSL classification at lead-free peak reflow temperature. APW7134 Package Code QA : DFN-10 Temp. Range I : -40 to 85 C Handling Code TU : Tube TR : Tape & Reel Lead Free Code L : Lead Free Device Blank : Original Device Handling Code Temp. Range Package Code Lead Free Code APW7134 QA: APW 7134 XXXXX XXXXX - Date Code Block Diagram Control Logic EA Oscillator 0.6V Σ ICOMP IRCMP Slop Compensation Frequency Shift FB1/ FB2 EN1/ EN2 IN1/ IN2 GND1/ GND2 SW1/ SW2 R S Q Q Shutdown RSENSE QP QN QSENSE Diagram Represents 1/2 of the APW7134
Copyright ANPEC Electronics Corp. Rev. A.1 - Aug., 2006 APW7134 www.anpec.com.tw3 Pin No. Name Function
1 EN1
Channel 1 Enable Control Input. Drive EN1 above 1.5V to turn on the Channel 1. Drive EN1 below 0.3V to turn it off . In shutdown situation, all functions are disabled to decrease the supply current below 1 µA.There is no pull hig h or pull low ability inside. 2 FB1 Channel 1 Feedback Input. Connect FB1 to the center point of the external resistor divider. The feedback voltage is 0.6V. 3 IN2 Channel 2 Supply Input. Bypass to GND with a 4.7µF or greater ceramic capacitor. 4 GND2 Ground 2. Connected the exposed pad to GND2. 5 SW2 Channel 2 Power Switch Output. Inductor connection to drains of the internal PMOSFET and NMOSFET switches.
6 EN2
Channel 2 Enable Control Input. Drive EN 2 above 1.5V to turn on the Channel 2. Drive EN2 below 0.3V to turn it off . In shutdown situation, all functions are disabled to decrease the supply current below 1 µA.There is no pull high or pull low ability inside. 7 FB2 Channel 2 Feedback Input. Connect FB2 to the center point of the external resistor divider. The feedback voltage is 0.6V. 8 IN1 Channel 1 Supply Input. Bypass to GND with a 4.7µF or greater ceramic capacitor. 9 GND1 Ground 1. Connected the exposed pad to GND1. 10 SW1 Channel 1 Power Switch Output. Inductor connection to drains of the internal PMOSFET and NMOSFET switches. Pin Description Absolute Maximum Ratings Symbol Parameter Value Unit VIN1/IN2 Input Supply Voltage (IN1/IN2 to GND1/GND2) -0.3 ~ 6 V VFB1/FB2 Voltage on FB1 and FB2 -0.3 ~ VIN1/IN2+0.3 V VEN1/EN2 Voltage on EN1 and EN2 -0.3 ~ VIN1/IN2+0.3 V VSW1/SW2 Voltage on SW1 and SW2 -0.3 ~ VIN1/IN2+0.3 V ISW_PEAK Peak SW Current 1.3 A TJ Junction temperature 150 °C TSTG Storage temperature -65 ~ 150 °C TSDR Soldering temperature, 10 seconds 300 °C VESD Minimum ESD rating (Human body mode) (Note 1) ±3 KV Note 1: The device is ESD sensitive. Handling precautions are recommended. Symbol Parameter Value Unit θ JA Junction-to-Ambient Resistance in free air (Note 2) 50 °C/W Thermal Characteristics Note 2: θ JA is measured on approximately 1¨ square of 1 oz copper.
Copyright ANPEC Electronics Corp. Rev. A.1 - Aug., 2006 APW7134 www.anpec.com.tw4 Recommended Operating Conditions (Note 3) Value Symbol Parameter Min. Typ. Max. Unit VIN1/IN2 Input Supply Voltage (IN1/IN2 to GND1/GND2) 2.5 5.5 V R2/R4 Feedback Resistance (Note 3) 200 KΩ IOUT Output Current 600 mA TA Operating ambient temperature -40 85 °C TJ Operating junction temperature -40 125 °C Note 3: Please refer to the typical application circuit.
Electrical Characteristics
Symbol Parameter Test Conditions Min. Typ. Max. Unit VIN1/IN2 Each Converter Input Voltage Range * 2.5 5.5 V IFB1/FB2 Each Converter Feedback current VFB1/FB2=0.6V * -30 30 nA VFB1/FB2 Each Converter Regulated Feedback Voltage * 0.588 0.6 0.612 V Δ VFB1/FB2 Each Converter Reference voltage Line regulation VIN1/IN2=2.5V to 5.5V * 0.04 0.4 %/V IPK Each Converter Peak Inductor Current VIN1/IN2=3V,VFB=0.5V or VOUT=90%, Duty cycle < 35% 0.75 1 1.25 A VLOADR Each Converter Load Regulation 0.5 % IQ Each Converter Quiescent Current Duty Cycle=0; VFB=1.5V 300 400 µA The * denotes the specifications that apply over TA = -40°C ~ 85°C, otherwise specifications are at TA=25°C
Copyright ANPEC Electronics Corp. Rev. A.1 - Aug., 2006 APW7134 www.anpec.com.tw5 Electrical Characteristics (Cont.) The * denotes the specifications that apply over TA = -40°C ~ 85°C, otherwise specifications are at TA=25°C APW7134 Symbol Parameter Test Conditions Min. Typ. Max. Unit IQ-SD Each Converter Quiescent Current in Shutdown VEN1/EN2=0V,VIN=4.2V 0.1 1 µA fOSC Each Converter Oscillator Frequency VFB=0.6V 1.2 1.5 1.8 MHz fOSC_FFB Each Converter Frequency Foldback VFB=0V 210 KHz RDS-P Each Converter On Resistance of PMOSFET ISW=100mA 0.4 0.5 Ω RDS-N Each Converter On Resistance of NMOSFET ISW=-100mA 0.35 0.45 Ω ILSW Each Converter SW Leakage Current VEN1=0V,VSW=0V or 5V,VIN=5V ±0.01 ±1 µA VEN1/EN2 Each Converter Enable Threashold * 0.3 1 1.5 V IEN1/EN2 EN1/EN2 Leakage Current * ±0.01 ±1 µA Application Circuit Ω Ω Ω Ω Ω Ω EN1 SW1 FB1 EN2 SW2 FB2 IN1 IN2 GND1 GND2 APW7134 CIN1 4.7uF R5 100K VIN1/IN2 OFF ON OFF ON CIN2 4.7uFR6 100K VOUT1 1.8V 600mA VOUT2 3.3V 600mA COUT1 10uF COUT2 10uF 300K 150K 680K 150K 2.2uH 2.2uH Typical Application
Copyright ANPEC Electronics Corp. Rev. A.1 - Aug., 2006 APW7134 www.anpec.com.tw6 100 200 300 400 500 600 700 -50 -25 0 25 50 75 100 125 NMOS PMOS 1200 1300 1400 1500 1600 1700 1800 2 3 4 5 6 1200 1300 1400 1500 1600 1700 1800 -50 -25 0 25 50 75 100 125 0.585 0.590 0.595 0.600 0.605 0.610 0.615 -50 -25 0 25 50 75 100 125 Typical Operating Characteristics Temperature (o C) Temperature (o C) Reference Voltage (V) Frequency (KHz) Oscillator FrequencyReference Voltage Temperature (o C)Supply Voltage (V) ON Resistance (mΩ ) RDS(ON) vs TemperatureOscillator Frequency vs Supply Voltage VIN=5.5VVIN=5.5V VIN=2.5VVIN=2.5V Frequency (KHz) TA=25o C VIN=2.7VVIN=2.7V VIN=3.6VVIN=3.6V VIN=4.2VVIN=4.2V VIN=3.6V
Copyright ANPEC Electronics Corp. Rev. A.1 - Aug., 2006 APW7134 www.anpec.com.tw7 100 100 100 100 200 300 400 500 600 0 1 2 3 4 5 6 Input Voltage (V) Output Current (mA) ON Resistance (mΩ ) Efficiency (%) Efficiency vs Output CurrentRDS(ON) vs Input Voltage Output Current (mA) Efficiency vs Output Current Efficiency (%) PMOSPMOS NMOSNMOS VOUT=1.2V TA=25o C VIN=2.7VVIN=2.7V VIN=3.6VVIN=3.6V VIN=4.2VVIN=4.2V VOUT=1.5V TA=25o C VIN=2.7VVIN=2.7V VIN=3.6VVIN=3.6V VIN=4.2VVIN=4.2V VIN=4.2VVIN=4.2V VIN=3.6VVIN=3.6V VIN=2.7VVIN=2.7V Efficiency vs Output Current Output Current (mA) Efficiency (%) Typical Operating Characteristics (Cont.) VOUT=2.5V TA=25o C
Copyright ANPEC Electronics Corp. Rev. A.1 - Aug., 2006 APW7134 www.anpec.com.tw8 100 2 3 4 5 6 200 220 240 260 280 300 320 340 360 380 400 2 3 4 5 6 100 2 3 4 5 6 100 2 3 4 5 6 Input Voltage (V) Input Voltage (V) Efficiency (%) Efficiency (%) Efficiency vs Input VoltageEfficiency vs Input Voltage Supply Voltage (V)Input Voltage (V) Dynamic Supply Current (µA) Dynamic Supply Current vs Supply VoltageEfficiency vs Input Voltage Efficiency (%) IOUT=100mAIOUT=100mA IOUT=600mAIOUT=600mA IOUT=10mAIOUT=10mA VOUT=1.5V TA=25o C IOUT=100mAIOUT=100mA IOUT=600mAIOUT=600mA IOUT=10mAIOUT=10mA VOUT=1.8V TA=25o C VOUT=2.5V TA=25o C IOUT=100mAIOUT=100mA IOUT=600mAIOUT=600mA IOUT=10mAIOUT=10mA Typical Operating Characteristics (Cont.)
Copyright ANPEC Electronics Corp. Rev. A.1 - Aug., 2006 APW7134 www.anpec.com.tw9 500 550 600 650 700 750 800 -50 -25 0 25 50 75 100 125 100 150 200 250 300 -50 -25 0 25 50 75 100 125 Typical Operating Characteristics (Cont.) Temperature (o C) Temperature (o C) PMOSFET Leakag(nA) NMOSFET Leakage(nA) NMOSFET Leakage vs TemperaturePMOSFET Leakage vs Temperature VIN=5.5V VIN=5.5V Functional Descriptions Main Control Loop The APW7134 has dual independent constant fre- quency current mode PWM step-down converters. All the main and synchronous switches are internal to reduce the external components. During normal operation, the internal PMOSFET is turned on, but is turned off when the inductor current at the input of ICOMP to reset the RS latch. The load current increases, it causes a slight decrease in the feedback voltage, which in turn, causes the EA’s output voltage to in- crease until the average inductor current matches the new load current. While the internal power PMOSFET is off, the internal power NMOSFET is turned on until the inductor current starts to reverse, as indicated by the current reversal comparator IRCMP, or the begin- ning of next cycle. When the NMOSFET is turned off by IRCMP, it operates in the discontinuous conduction mode. Pulse Skipping Mode Operation At light load with a relative small inductance, the inductor current may reach zero. The internal power NMOSFET is turned off by the current reversal comparator, IRCMP, and the switching voltage will ring. This is discontinuous mode operation, and is normal behavior for the switching regulator. At very light load, the APW7134 will automatically skip some pulses in the pulse skipping mode to maintain the output regulation. The skipping process modulates smoothly depend on the load. Short Circuit Protection In the short circuit situation, the output voltage is almost zero volts. Output current is limited by the ICOMP to prevent the damage of electrical circuit. In the normal operation, the two straight line of the inductor current ripple have the same height, it means the volts-seconds product is the same. When the short circuit operation occurs, the output voltage down to
Copyright ANPEC Electronics Corp. Rev. A.1 - Aug., 2006 APW7134 www.anpec.com.tw10 zero leads to the voltage across the inductor maximum in the on period and the voltage across the inductor minimum in the off period. In order to maintain the volts-seconds balance, the off-time must be extended to prevent the inductor current run away. Frequency decay will extend the switching period to provide more times to the off-period, then the inductor current have to restrict to protect the electrical circuit in the short situation. Dropout Operation An important detail to remember is that on resistance of PMOSFET switch will increase at low input supply voltage. Therefore, the user should calculate the power dissipation when the APW7134 is used at 100% duty cycle with low input voltage. Functional Descriptions (Cont.) Short Circuit Protection Cont. Slope Compensation Slope compensation provides stability in constant frequency current mode architecture by preventing sub-harmonic oscillations at high duty cycle. It is accomplished internally by adding a compensating ramp to the inductor current signal at duty cycle in excess of 40%. Normally, this results in a reduction of maximum inductor peak current for duty cycles greater than 40%. In the APW7134, the reduction of inductor peak current recovered by a special skill at high duty ratio. This allow the maximum inductor peak current maintain a constant level through all duty ratio. Application Description where fS is the switching frequency of APW7134 and Δ IL is the value of the worst current ripple, it can be any value of current ripple that smaller than the worst value you can accept. In order to perform high efficiency, Inductor Selection Due to the high switching frequency as 1.5MHz, the inductor value of the application field of APW7134 is usually from 1µH to 4.7µH. The criterion to selecting a suitable inductor is dependent on the worst current ripple throughout the inductor. The worst current ripple defines as 40% of the fully load capability. In the APW7134 applications, the worst value of current ripple is 240mA, the 40% of 600mA. Evaluate L by equation (1): ( ) SLIN OUTOUTIN fI V VVVL ⋅Δ⋅⋅−= selecting a low DC resistance inductor is a helpful way. Another important parameter is the DC current rating of the inductor. The minimum value of DC current rating equals the full load value of 600mA, plus the half of the worst current ripple, 120mA. Choose inductors with suitable DC current rating to ensure the inductors don’t operate in the saturation. Input Capacitor Selection The input capacitor must be able to support the maximum input operating voltage and maximum RMS input current. The Buck converter absorbs current from input in pulses. (1)
Copyright ANPEC Electronics Corp. Rev. A.1 - Aug., 2006 APW7134 www.anpec.com.tw11 Figure-1 shows a schematic of a Buck structure. The waveforms show as Figure-2. Figure-2 IIN IOUT IL IIN I(CIN) I(COUT) IOUT I(Q1) PWM D*TS (1-D)*TS Observe the waveform of I(CIN),the RMS value of I(CIN) is ( ) ( )[ ] ( )2 IN INOUTIN D1IDIICI −⋅+⋅−= Replace D and IIN by following relation: IN OUT V VD = OUTIN IDI ⋅= The RMS value of input capacitor current equal: ( ) ))D1(DICI OUTIN −⋅= When D=0.5 the RMS current of input capacitor will be maximum value. Use this value to choose the input capacitor with suitable current rating. Figure-1 L COUT CINVIN I(CIN)IIN I(Q1) I(L) I(COUT) IOUT PWM Application Description (Cont.) Input Capacitor Selection Cont. Output Capacitor Selection The output voltage ripple is a significant parameter to estimate the performance of a convertor. There are two discrete components that affect the output voltage ripple bigger or smaller. It is recommended to use the criterion has mentioned above to choose a suitable inductor. Then based on this known inductor current ripple condition, the value and properties of output capacitor will affect the output voltage ripple better or worse. The output voltage ripple consists of two portions, one is the product of ESR and inductor current ripple, the other portion is a function of the inductor current ripple and the output capacitance. Figure-3 shows the waveforms to explain the part decided by the output capacitance. I(COUT)0A Δ VOUT1 Δ IL VOUT 0.5TS Figure-3 (2) (3) (4) (5)
Copyright ANPEC Electronics Corp. Rev. A.1 - Aug., 2006 APW7134 www.anpec.com.tw12 Application Description (Cont.) 1OUTOUTSL VCT2 1I2 1Q Δ⋅= ⋅Δ= where TS is the inverse of switching frequency and the Δ IL is the inductor current ripple. Move the COUT to the left side to estimate the value of Δ VOUT1 as equation (7). OUT SL 1OUT TIV ⋅ ⋅Δ=Δ As mentioned above, one part of output voltage ripple is the product of the inductor current ripple and ESR of output capacitor. The equation (8) explains the out- put voltage ripple estimation. ⋅+⋅Δ=Δ OUT S LOUT TESLIV Evaluate the Δ VOUT1 by the ideal of energy equalization. According to the definition of Q, Thermal Considerations ( ) ( )[ ]D1RDRIP ONN_DSONP_DS OUTD −⋅+⋅= APW7134 has internal over temperature protection. When the junction temperature reaches 150 centigrade, APW7134 will turn off both internal power PMOSFET and NMOSFET. The estimation of the junc- tion temperature, TJ, defined as: JADJ PT θ⋅= where the θ JA is the thermal resistance of the package utilized by APW7134. +⋅= OUT R R16.0V FB APW7134 VOUT age setting by the users. A suggestion of maximum value of R2 is 200KΩ to keep the minimum current that provides enough noise rejection ability through the resistor divider. The output voltage programmed by the equation: Output Capacitor Selection Output Voltage Setting APW7134 has the adjustable version for output volt APW7134 is a high efficiency switching converter, it means less power loss transferred into heat. Due to the on resistance difference between internal power PMOSFET and NMOSFET, the power dissipation in the high converting ratio is greater than low converting ratio. The worst case is in the dropout operation, the mainly conduction loss dissipate on the internal power PMOSFET. The power dissipation nearly defined as: (6) (7) (8) (9) (10) (11) Layout Considerations The high current paths (GND1/GND2, IN1/IN2 and SW1/SW2) should be placed very close to the device with short, direct and wide traces. Input capacitors should be placed as close as possible to the respec- tive IN and GND pins. The external feedback resistors shall be placed next to the FB pins. Keep the switch- ing nodes SW1/SW2 short and away from the feed- back network.
Copyright ANPEC Electronics Corp. Rev. A.1 - Aug., 2006 APW7134 www.anpec.com.tw13
Package Information
e b AD E Min. Max. Min. Max. A 0.80 1.00 0.031 0.039 A1 0.00 0.05 0.000 0.002 b 0.18 0.30 0.007 0.012 D D2 2.20 2.50 0.087 0.098 E E2 1.50 1.80 0.059 0.071 e L 0.35 0.45 0.014 0.018 0.50 BSC 0.016 BSC 3.00 BSC 0.118 BSC Dim Millimeters Inches 3.00 BSC 0.118 BSC 0.20 REF 0.008 REF DFN-10
Copyright ANPEC Electronics Corp. Rev. A.1 - Aug., 2006 APW7134 www.anpec.com.tw14 Carrier Tape & Reel Dimensions t Ao E W Po P Ko Bo D F Application A B C J T1 T2 W P E F D D1 Po P1 Ao Bo Ko T DFN-10 Cover Tape Dimensions Application Carrier Width Cover Tape Width Devices Per Reel DFN-10 12 9.2 3000 A J B C (mm)
Copyright ANPEC Electronics Corp. Rev. A.1 - Aug., 2006 APW7134 www.anpec.com.tw15 t 25 C to Peak tp Ramp-up tL Ramp-down ts Preheat Tsmax Tsmin TL TP Temperature Time Critical Zone TL to T P Physical Specifications Terminal Material Solder-Plated Copper (Solder Material : 90/10 or 63/37 SnPb) , 100%Sn Lead Solderability Meets EIA Specification RSI86 -91, ANSI/J -STD-002 Category 3. Reflow Condition (IR/Convection or VPR Reflow) Classificatin Reflow Profiles Profile Feature Sn-Pb Eutectic Assembly Pb-Free Assembly Average ramp-up rate (TL to TP) 3°C/second max. 3°C/second max. Preheat - Temperature Min (Tsmin) - Temperature Max (Tsmax) - Time (min to max) (ts) 100°C 150°C 60-120 seconds 150°C 200°C 60-180 seconds Time maintained above: - Temperature (TL) - Time (tL) 183°C 60-150 seconds 217°C 60-150 seconds Peak/Classificatioon Temperature (Tp) See table 1 See table 2 Time within 5°C of actual Peak Temperature (tp) 10-30 seconds 20-40 seconds Ramp-down Rate 6°C/second max. 6°C/second max. Time 25°C to Peak Temperature 6 minutes max. 8 minutes max. Notes: All temperatures refer to topside of the package .Measured on the body surface.
Copyright ANPEC Electronics Corp. Hsin Tien City, Taipei Hsien, Taiwan, R. O. C. Table 1. SnPb Entectic Process – Package Peak Reflow Temperature s Table 2. Pb -free Process – Package Classification Reflow Temperatures including the stated classification temperature (this means Peak reflow temperature +0 °C. For example 260 °C+0 °C) at the rated MSL level.