APGA1602SEC-E-KA KINGBRIGHT

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 5

Technical content

Features

z 1.6mmx0.2mm right angle SMT LED,0.2mm thickness. z Low power consumption. z Wide viewing angle. z Ideal for backlight and indicator. z Moisture sensitivity level : level 3. z Package :2000pcs / reel. z Tinned pads for improved solderability. z RoHS compliant.

SPEC NO: DSAN2008 REV NO: V.2A DATE: APR/22/2015 PAGE: 2 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1203013775 Selection Guide Absolute Maximum Ratings at TA=25°C Electrical / Optical Characteristics at TA=25°C Note: 1. 1 / 10 Duty Cycle, 0.1ms Pulse Width. Part No. Dice Lens Type Iv (mcd) [2] @ 20mA Viewing Angle [1] Min. Typ. 2θ1/2 APGA1602SEC/E/KA Hyper Red (AlGaInP) Water Clear 80 200 *55 *120 150°(H) 120°(V) Symbol Parameter Device Typ. Max. Units Test Conditions λpeak Peak Wavelength Hyper Red 632 nm IF=20mA λD [1] Dominant Wavelength Hyper Red 624 nm IF=20mA Δλ1/2 Spectral Line Half-width Hyper Red 20 nm IF=20mA VF [2] Forward Voltage Hyper Red 2.05 2.4 V IF=20mA IR Reverse Current Hyper Red 10 uA VR=5V Parameter Hyper Red Units Power dissipation 48 mW DC Forward Current 20 mA Peak Forward Current [1] 100 mA Reverse Voltage 5 V Operating Temperature -40°C To +85°C Storage Temperature -40°C To +100°C Notes: 1. θ1 / 2 is the angle from optical centerline where the luminous intensity is 1 / 2 of the optical peak value. 2. Luminous intensity / luminous Flux: + / -15%. * Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Notes: 1. Wavelength: + / -1nm. 2. Forward Voltage: + / -0.1V. 3. Wavelength value is traceable to the CIE127-2007 compliant national standards. 4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or premature failure.

SPEC NO: DSAN2008 REV NO: V.2A DATE: APR/22/2015 PAGE: 3 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1203013775 Hyper Red APGA1602SEC/E/KA

SPEC NO: DSAN2008 REV NO: V.2A DATE: APR/22/2015 PAGE: 4 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1203013775 APGA1602SEC/E/KA Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Dimensions (Units : mm)

SPEC NO: DSAN2008 REV NO: V.2A DATE: APR/22/2015 PAGE: 5 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1203013775 PACKING & LABEL SPECIFICATIONS APGA1602SEC/E/KA Terms and conditions for the usage of this document 1. The information included in this docum ent reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the dat asheet. If customer usage exceeds the spec ified limits, Kingbright will not be respon sible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applicati ons. If customer's application ha s special reliability requirements or have life-threatening liabilitie s, such as automotive or m edical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes