AP17E070064A ETC2
Document overview
- Manufacturer or author: Provided By www.digicamel.com(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 11
Technical content
SPE-11-8-144/B | page 1 of 11 AP17E.07.0064A Specification Part No. AP17E.07.0064A Product Name 17mm One Stage GPS Active Patch Antenna Module with Front End SAW Filter Feature 17mm*17mm*6.3mm 64mm 1.13 IPEX MHFI Wide Voltage 1.8V~5.5V 15dB LNA Tested in Free space RoHS Compliant
SPE-11-8-144/B | page 2 of 11 The AP.17E is a one stage 17mm active patch antenna that has been designed specifically for embedded (inside device) integration with GPS receiver modules. The AP.17E combines a 17*17*4mm ad- vanced low profile ceramic patch antenna with a one stage LNA and a front-end SAW filter with ultra thin coaxial cable. It comes with it’s own integrated ground-plane. The front end SAW filter reduces the risks where there is a cellular transmitter nearby of interference from out of band frequen- cies which can cause LNA burn-out, satu- ration, or radiated spurious emissions. The antenna can work on a wide input voltage from 1.8V to 5.5V with best in class power consumption figures. If further tuning and optimization specific to a customer device is required Taoglas offers a custom tuned and optimized part service. Contact sales@taoglas.com for more information. Cables and connectors can be customized according to request. 1. Introduction ANTENNA SAW Filter LNA I-PEX + cable
SPE-11-8-144/B | page 3 of 11 2. Specification
2.1 Patch Antenna
2.2 LNA
Frequency 1575.42 ± 1.023MHz Gain @ Zenith -1.0dBic Typ. @ Zenith Polarization RHCP Axial Ratio 3.0dB max @ Zenith Patch Dimension 17*17*4mm Parameter Specification Frequency 1575.42 ± 1.023MHz Outer Band Attenuation F0=1575.42MHz F0±30MHz 2dB min. F0±50MHz 18dB min. F0±100MHz 25dB min. Output Impedance 50Ω Output VSWR 2.0 Max Pout at 1dB Gain Compression point Typ. -2dBm Min. -6dBm LNA Gain, Power Consumption and Noise Figure Voltage LNA Gain (Typ) Power Consumption(mA) Typ Noise Figure Typ Min. 1.8V 13dB 1.6mA 2.5dB Typ. 3.0V 16dB 3.5mA 2.5dB Max. 5.5V 17dB 7.6mA 2.6dB Parameter Specification RF Cable Coaxial Cable Ø 1.13 ± 0.1mm, length 64mm ± 2.5mm Connector IPEX MHFI (U.FL)
2.3 Cable* & Connector
SPE-11-8-144/B | page 4 of 11 3. LNA Gain and Out Band Rejection @3.0V Cg1 Tr1 S21 >1 1.5754200 GHz 16.111 dB Cg1 Tr1 S21 2 1.6054200 GHz -27.059 dB Cg1 Tr1 S21 3 1.5454200 GHz 12.455 dB Cg1 Tr1 S21 4 1.6254200 GHz -34.597 dB Cg1 Tr1 S21 5 1.5254200 GH -3.4458 dB Cg1 Tr1 S21 6 1.6754200 GHz -20.195 dB Cg1 Tr1 S21 7 1.4754200 GHz -10.158 dB Tr1 S21 Log Mag 10.00dB/ Ref -40.00dB (F2) 1 Center 1.57542 GHz Span 400 MHz 2/8 CorIFBW 500 kHz 30.00 20.00 10.00 0.000 -10.00 -20.00 -30.00 -40.00 -50.00 -60.00 -70.00 >1 1.5754200 GHz 16.111 dB
SPE-11-8-144/B | page 5 of 11 4. LNA Noise Figure @3.0V 5. Total Specification (through Antenna, LNA, Cable and Connector) Parameter Specification Frequency 1575.42 ± 1.023MHz Gain At 3V: 15 ± 3dBic @ 90° Output Impedance 50Ω Polarization RHCP Output VSWR Max 2.0 Operation Temperature -40°C to + 85°C Storage Temperature -40°C to + 85°C Relative Humidity 40% to 95% Antenna 17*17*6.1mm 40.00 GAIN Scale/ 5.000 dB -10.00 Mkr1 1.5754 GHz 2.431 dB 15.270 dB Center 1.57542 GHz BW 4 MHz Points 11 Span 3.00 MHz Tcold 296.50 K Avgs Off Att 0/ - - dB Loss Off Corr 9.000 NFIG Scale/ 1.000 dB -1.000
-10 -15 -20 -25 -30 -35 -40 SPE-11-8-144/B | page 6 of 11 6. Radiation Patterns
6.1 XZ Plane Radiation
Pattern Model No. Test Mode Freq (MHz) Max Gain(dBi) Min Gain(dBi) Avg. Gain(dBi) Source Polar. Date
-10 -15 -20 -25 -30 -35 -40 SPE-11-8-144/B | page 7 of 11
6.2 YZ Plane Radiation
Pattern Model No. Test Mode Freq (MHz) Max Gain(dBi) Min Gain(dBi) Avg. Gain(dBi) Source Polar. Date
-10 -15 -20 -25 -30 -35 -40 SPE-11-8-144/B | page 8 of 11
6.3 XY Plane Radiation
Pattern Model No. Test Mode Freq (MHz) Max Gain(dBi) Min Gain(dBi) Avg. Gain(dBi) Source Polar. Date
SPE-11-8-144/B | page 9 of 11 7. Technical Drawing This drawing and its inherent design concepts are property of Taoglas. Not to be copied or given to third parties without the written consent of Taoglas. TW Design Centre IPEX MHF 1 "A" A ALL Initial Design Kiwi 2011/10/20 Top Side Bottom NOTE: 1.Soldered area 2.Shielding case 3.Double Sided Adhesive 4.The connector position has special orientation to the PCB as per drawing. 5.All material must be RoHS compliant. 6.Open/short QC, VSWR required. Name Material Finish QTY AP.17E Patch (17*17*4mm) Ceramic Clear 1 FEP Gray2
3 Gold PlatedBrass
1.13 Coaxial Cable
14 Tin PlatedTin (SPTE)Shielding Case
15 GreenFR4 0.8tPCB P/N AP.17E OD.113.CM IPEX.MHFI.113
16 White LinerNITTO 5015Double Sided Adhesive
AP.17E Name P/N Material Finish QTY 1 AP.17E Patch (17*17*4mm) AP.17E Ceramic Clear 1 2 1.13 Coaxial Cable OD.113.CM FEP Gray 1 3 IPEX MHF1 Connector IPEX.MHFI.113 Brass Gold Plated 1
4 Shielding Case Tin (SPTE) Tin Plated 1
5 PCB FR4 0.8t Green 1 NOTE: 1. Soldered area 2. Shielding case 3. Double Sided Adhesive 4. The connector position has special orientation to the PCB as per drawing. 5. All material must be RoHS compliant. 6. Open/short QC, VSWR required. This drawing and its inherent design concepts are property of Taoglas. Not to be copied or given to third parties without the written consent of Taoglas. TW Design Centre IPEX MHF 1 "A" A ALL Initial Design Kiwi 2011/10/20 Top Side Bottom NOTE: 1.Soldered area 2.Shielding case 3.Double Sided Adhesive 4.The connector position has special orientation to the PCB as per drawing. 5.All material must be RoHS compliant. 6.Open/short QC, VSWR required. Name Material Finish QTY AP.17E Patch (17*17*4mm) Ceramic Clear 1 FEP Gray2 15 GreenFR4 0.8tPCB P/N AP.17E OD.113.CM IPEX.MHFI.113 AP.17E
SPE-11-8-144/B | page 10 of 11 8. Plugs Usage Precautions (1) To disconnect connectors, insert the end portion of I-PEX under the connector flanges and pull off vertically, in the direc- tion of the connector mating axis. (2) To mate the connectors, the mating axes of both connectors must be aligned and the connectors can be mated. The “click” will confirm fully mated connection. Do not attempt to insert on an extreme angle. After the connectors are mated, do not apply a load to the cable in excess of the values indicated in the diagram below.
8.1 Mating / unmating
8.2 Pull forces on the cable after connectors are mated
P/N : 90192-001 RECEPTACLE PLUG RECE 2N MAX. 2N MAX. 4N MAX. Coaxial Cable
SPE-11-8-144/B | page 11 of 11 9. Packaging Taoglas makes no warranties based on the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Taoglas reserves all rights to this document and the information contained herein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. Copyright © 2012, Taoglas Ltd.