AP1-B

AP-A_V01 OMRON

Document overview

• Manufacturer or author: Provided By digicamel.com
• PDF pages: 2

Technical content

Z/A/X/DZ Common Accessories Dimensions (Unit: mm) Terminal Covers Note: Each dimension has a tolerance of ±0.4 mm unless otherwise specified. (±0.8 mm for the AP-Z) Common to Z, A, X, and DZ Models The Terminal Covers can be attached to Z, A, X, and DZ Switches. The Terminal Cover is secured with mounting screws and protects the casing and terminal wires from dust, vibration, or fingers, thus preventing terminal short-circuiting, ground faults, wire disconnection or improper connection, and electric shock accidents. Terminal Covers made of phenol resin have five or six thin wall sections. These sections can be torn open for providing holes for lead cables at desired points. Operation Information Note: Use a Terminal Cover for screw terminals fir DZ-series Switches with soldering terminals. Terminal Covers (Sold Separately) Application Soldering terminal use Screw terminal use RemarksMaterial Mounting direction Model Phenol resin Side mounting AP-A AP-B --- Metal press mold Side mounting AP1-A AP1-B Used for AP-A and AP-B Vinyl chloride Side mounting AP-Z --- Use a Separator when it is difficult to provide a sufficient insulation distance or when using the Switch near metal parts or copper wires. Operation Information Separator (Sold Separately) Model SEPARATOR FOR Z 52.8 25.4 6.4 16.3 21 8 2.15R 4.3+0.2 0 4.3+0.2 AP-A Soldering Terminal Use (Phenol Resin) Note: The Cover has five thin, easy-to-separate portions for easy lead wire connections. 53.8 25.4 6.5 20.2 21 8 2.15R 4.3+0.2 0 4.3+0.2 AP-B Screw Terminal Use (Phenol Resin) Note: The Cover has six thin, easy-to-separate portions for easy lead wire connections. 54.4 25.4 7.2 17.1 22.6 8.5 2.15R 4.3+0.2 0 4.3+0.2 AP1-A Soldering Terminal Use (Metal Press Mold) Note: The Cover has five holes for easy lead wire connections. 55.4 25.4 22.6 8.5 2.15R 4.3+0.2 0 4.3+0.2 AP1-B Screw Terminal Use (Metal Press Mold) Note: The Cover has six holes for easy lead wire connections. 25.4 1212 A B Pressure plate (t1 steel) Two, 4.2 dia. × 20 Phillips screw (with plane washer and nut)Nut 15 13 A-A' cross-section B-B' cross-section 8 dia. 6 dia. Note: A 6-dia. or 8-dia. cable can be used by cutting the cable pull-out hole to the size of the cable to be used. Cable Pull-out Dimension AP-Z Soldering or Screw Terminal Use (Vinyl Chloride) 25.4±0.2 11.9 13.5 49.2±0.5 Two, 4.5 dia. t = 0.38 Note: 1. Each dimension has a tolerance of ±0.4 mm unless otherwise specified. 2. The material is EAVTC (Epoxide Alkyd Varnished Tetron Cloth) and its heat-resisting temperature is 130°C. Separator http://www.ia.omron.com/ 1(c)Copyright OMRON Corporation 2007 All Rights Reserved.

2007.3 OMRON Corporation Industrial Automation Company http://www.ia.omron.com/ (c)Copyright OMRON Corporation 2007 All Rights Reserved. In the interest of product improvement, specifications are subject to change without notice. Read and Understand This Catalog Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have an y questions or comments. Warranty and Limitations of Liability WARRANTY OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specifi ed) from date of sale by OMRON. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. OMRON DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. LIMITATIONS OF LIABILITY OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS, OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT LIABILITY. In no event shall responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted . IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS REGARDING THE PRODUCTS UNLESS OMRON'S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR REPAIR. Application Considerations SUITABILITY FOR USE OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of products in the customer's application or use of the product. At the customer's request, OMRON will provide applicable third party certi fi cation documents identifying ratings and limitations of use that apply to the products. This information by itself is not suf fi cient for a complete determination of the suitability of the products in combination with the end product, machine, system, or other application or use. The following are some examples of applications for which particular attention must be given. This is not intended to be an exh austive list of all possible uses of the products, nor is it intended to imply that the uses listed may be suitable for the products:

• Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this catalog.
• Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry or government regulations.
• Systems, machines, and equipment that could present a risk to life or property. Please know and observe all prohibitions of use applicable to the products. NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. Disclaimers CHANGE IN SPECIFICATIONS Product speci fi cations and accessories may be changed at any time based on improvements and other reasons. It is our practice to change model numbers when published ratings or features are changed, or when signi fi cant construction changes are made. However, some speci fi cations of the product may be changed without any notice. When in doubt, special model numbers may be assigned to fi x or establish key speci fi cations for your application on your request. Please consult with your OMRON representative at any time to con fi rm actual specifi cations of purchased product. DIMENSIONS AND WEIGHTS Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when tolerances are shown. ERRORS AND OMISSIONS The information in this catalog has been carefully checked and is believed to be accurate; however, no responsibility is assume d for clerical, typographical, or proofreading errors, or omissions. PERFORMANCE DATA Performance data given in this catalog is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of OMRON’s test conditions, and the users must correlate it to actual application requirements. Actual performance is subject to the OMRON Warranty and Limitations of Liability. PROGRAMMABLE PRODUCTS OMRON shall not be responsible for the user's programming of a programmable product, or any consequence thereof. COPYRIGHT AND COPY PERMISSION This catalog shall not be copied for sales or promotions without permission. This catalog is protected by copyright and is intended solely for use in conjunction with the product. Please notify us before copying or reproducing this catalog in any manner, for any other purpose. If copying or transmitting this catalog to another, please copy or transmit it in its entirety.