AN6096FHN

AN6096FHN PANASONIC

Document overview

• Manufacturer or author: Provided By digicamel.com
• PDF pages: 6

Technical content

ICs for Mobile Communication AN6096FHN Transmission and reception IC for cellular telephone n Overview The AN6096FHN is a transmission and recep- tion IC for a cellular telephone. It is encapsulated in the QFN package which is very thin and very small outline by using our exclusive process method. It integrates QPSK (Quadrature phase shift key- ing) modulator for transmission and an IF circuit for reception in a single chip. It contributes to real- ization of thinner and lighter equipment by adopt- ing a very small package and designing a low power consumption circuit. n Features

• Integrating an orthogonal modulation circuit for transmission and an IF circuit for reception on a single chip
• Low power consumption by using an indirect modulation system in transmission block
• Built-in APC circuit for transmission output adjustment
• High input sensitivity by optimizing circuit in reception circuit
• Built-in RSSI circuit of wide dynamic range in reception block n Applications
• Cellular telephone n Block Diagram QFN024-P-0405 Unit: mm /, /, /, /,/, 5.0±0.1 3-C0.5 19 13 4.0±0.1 Seating plane R0.3 4.0±0.1 2.0±0.2 (1.10) 4.2±0.2 3.0±0.1 A B 0.2±0.1 0.80max. S 0.50 0.2±0.1 0.10 S S A BM 0.10 RSOUT8APC/BS 24 RXLOIN9I-IN 23 RXMXIN10I-IN 22 VCCMIX11Q-IN 21 MXOUT12Q-IN 20 VCCMOD19TXLO1 1 VCCOUT18GNDMOD 2 TXOUT17TXLO2 3 GNDOUT16TXLO2R 4 LMIN15GNDRX 5 LMDEC214LMOUT 6 LMDEC113VCCLIM 7 IO IO IO IO RSSI

AN6096FHN ICs for Mobile Communication n Pin Descriptions Pin No. Symbol Description 13 LMDEC1 Lim. decouple 1 14 LMDEC2 Lim. decouple 2 15 LIMIN Lim. in

16 GNDOUT GND TX-out

17 TXOUT TX-output

18 VCCOUT V CC TX-out

19 VCCMOD V CC TX-mod.

20 Q-IN Q input

21 Q-IN Q input

22 I-IN I input

23 I-IN I input

24 APC / BS APC / BS

Pin No. Symbol Description

1 TXLO1 TX local 1-in

2 GNDMOD GND TX-mod.

3 TXLO2 TX local 2

4 TXLO2R TX local 2-ref.

5 GNDRX GND-RX

6 LMOUT Lim. out 7 VCCLIM V CC lim.

8 RSOUT RSSI out

9 RXLOIN RX local-in

10 RXMXIN RX mix.-in 11 VCCMIX V CC mix. 12 MXOUT Mix. out n Absolute Maximum Ratings Parameter Symbol Rating Unit Supply voltage V CC 4.2 V Supply current I CC 60 mA Power dissipation *2 PD 125 mW Operating ambient temperature *1 T opr -30 to +80 °C Storage temperature *1 Tstg -55 to +125 °C Note) *1: Except for the operating ambient temperature and storage temperature, all ratings are for Ta = 25°C. *2: The power dissipation shown is for the independent IC without a heat sink at Ta = 80°C. Refer to "n Application Notes". n Recommended Operating Range Parameter Symbol Range Unit Supply voltage V CC 2.7 to 4.0 V

ICs for Mobile Communication AN6096FHN Parameter Symbol Conditions Min Typ Max Unit Consumption current *1 ICCTX Lo1 = 178 MHz, -25 dBm ¾ 25 33 mA (Transmission) Lo2 = 1 619 MHz, -20 dBm V APC = 2.3 V Sleep current *1 ISLTX No signal, VAPC/BS = 0 V ¾ 01 0 mA Output level 1 *1 PO1 Lo1 = 178 MHz, -25 dBm -16 -13 ¾ dBm Lo2 = 1 607 MHz, -20 dBm V APC = 2.3 V Output level 2 *1 PO2 Lo1 = 178 MHz, -25 dBm -16 -13 ¾ dBm Lo2 = 1 631 MHz, -20 dBm V APC = 2.3 V Minimum output level *1 Pmin Lo1 = 178 MHz, -25 dBm ¾- 50 -43 dBm Lo2 = 1 619 MHz, -20 dBm V APC = 1.0 V Consumption current (Reception) *2 ICCRX No signal ¾ 3.2 4.5 mA Mix. conversion gain *2 G MX V M1 = 60 dBm, SW1 = b 21 23.5 26 dB Filter loss: except for -5.5 dB Mix. maximum output amplitude *2 V MX V M1 = 105 dBm, SW1 = b 101 107 ¾ dB m Filter loss: except for -5.5 dB Lim. voltage gain *2 G LM V L1 = 15 dBm 80 85 90 dB Lim. maximum output amplitude *2 V LM V L1 = 80 dBm, 400 kHz component 0.90 1.25 1.60 V[p-p] RSSI output voltage 1 *2 V S1 V L1 = 0 dBm 0 0.23 0.6 V RSSI output voltage 2 *2 V S2 V L1 = 115 dBm 2.31 2.6 2.91 V RSSI reference output inclination *3 D S V S (VIS) = VS1 + 0.12 V 1.39 1.8 2.19 V D S = VS (VIS + 75 dBm) - V(VIS) RSSI output DD S1 DD S1 = 5{VS (VIS + 15 dBm) 0.75 1 1.25 ¾ inclination variation 1 *3 - VS (VIS)}/ DS RSSI output DD S2 DD S2 = 5{VS (VIS + 30 dBm) 0.75 1 1.25 ¾ inclination variation 2 *3 - VS (VIS + 15 dBm)}/ DS RSSI output DD S3 DD S3 = 5{VS (VIS + 45 dBm) 0.75 1 1.25 ¾ inclination variation 3 *3 - VS (VIS + 30 dBm)}/ DS RSSI output DD S4 DD S4 = 5{VS (VIS + 60 dBm) 0.75 1 1.25 ¾ inclination variation 4 *3 - VS (VIS + 45 dBm)}/ DS RSSI output DD S5 DD S5 = 5{VS (VIS + 75 dBm) 0.75 1 1.25 ¾ inclination variation 5 *3 - VS (VIS + 60 dBm)}/ DS n Electrical Characteristics at Ta = 25°C Note) *1: VCC = 3.0 V, IQ signal amplitude: 0.35 V[p-p] (single phase), DC bias: 1.6 V, p/4 QPSK modulation wave Output frequency of PO1 : 1 429.002 5 MHz, Output frequency of PO2 : 1 453.002 5 MHz, Output frequency of Pmin: 1 441.002 5 MHz Lo input level is a setting value of signal source (output impedance 50 W ). *2: VCC2 = 3.0 V, SW1 = a, VLO3 = 90 dBm: f = 129.6 MHz, VM1 : f = 130 MHz, VL1: f = 400 kHz (input level of pin 15 excluding the attenuation by matching circuit and filter.) VMX and VLM are measured in high impedance unless otherwise specified. Lo input level is a setting value of signal source (output impedance 50 W ). *3: VIS is the input level of which the RSSI output voltage becomes VS1 + 0.12 V.

AN6096FHN ICs for Mobile Communication Parameter Symbol Conditions Min Typ Max Unit Carrier leak suppression amount CL Lo1 = 178 MHz, -25 dBm ¾- 35 ¾ dBc (fLO2 - fLO1 ) Lo2 = 1 619 MHz, -20 dBm V APC = 2.3 V IO: DC offset adjustment Image leak suppression amount IL Lo1 = 178 MHz, -25 dBm ¾- 35 ¾ dBc Lo2 = 1 619 MHz, -20 dBm V APC = 2.3 V, IO: level adjustment Near spurious suppression DU Lo1 = 178 MHz, -25 dBm ¾- 70 -65 dBc amount Lo2 = 1 619 MHz, -20 dBm V APC = 2.3 V Base band distortion suppression BD Lo1 = 178 MHz, -25 dBm ¾- 40 ¾ dBc amount Lo2 = 1 619 MHz, -20 dBm V APC = 2.3 V Adjacent channel leakage power BL1 Lo1 = 178 MHz, -25 dBm ¾- 45 -38 dBc suppression amount Lo2 = 1 619 MHz, -20 dBm (30 kHz detuning) V APC = 2.3 V Adjacent channel leakage power BL2 Lo1 = 178 MHz, -25 dBm ¾- 70 -60 dBc suppression amount Lo2 = 1 619 MHz, -20 dBm (50 kHz detuning) V APC = 2.3 V Adjacent channel leakage power BL3 Lo1 = 178 MHz, -25 dBm ¾¾ - 65 dBc suppression amount Lo2 = 1 619 MHz, -20 dBm (100 kHz detuning) V APC = 2.3 V APC variable width L APC Lo1 = 178 MHz, -25 dBm 30 37 ¾ dB Lo2 = 1 619 MHz, -20 dBm V APC = 1.0 V to 2.3 V APC output level control sensitivity SAPC Lo1 = 178 MHz, -25 dBm ¾ 46 ¾ dB/V Lo2 = 1 619 MHz, -20 dBm V APC = 1.0 V / 1.6 V In-band output level deviation DP Lo1 = 178 MHz, -25 dBm -1.5 ¾+ 1.5 dB Lo2 = 1 607 MHz to 1 631 MHz, -20 dBm V APC = 2.3 V Modulation precision EVM Lo1 = 178 MHz, -25 dBm ¾ 2.0 ¾ %rms Lo2 = 1 619 MHz, -20 dBm V APC = 2.3 V n Electrical Characteristics at Ta = 25°C (continued)

• Design reference data Note) The characteristics listed below are theoretical values based on the IC design and are not guaranteed. V CC1 = 3.0 V unless otherwise specified. Lo input level is a setting value of signal source (output impedance 50 W ).

ICs for Mobile Communication AN6096FHN n Application Notes

• PD ¾ Ta curves of QFN024-P-0405 PD ¾ Ta Power dissipation PD (W) 02 5 Ambient temperature Ta (°C) 50 75 100 125 0.100 0.200 0.300 0.279 0.500 0.500 0.600 0.660 0.700 Mounted on the standard printed circuit board (Glass epoxy:50 · 50 · t0.8 mm R th(j-a) = 151.5°C/W Independent IC without a heat sink R th(j-a) = 357.4°C/W
• Main characteristics Note) Test conditions are the same as "n Electrical Characteristics" unless otherwise specified. The characteristics listed below are theoretical values based on the IC design and are not guaranteed. APC control voltage characteristics Mix. characteristics APC control voltage (V) Output level PO (dBm) Adjacent channel leakage power suppression amount ACP 30 kHz, ACP 50 kHz (dBc) Proximity spurious suppression amount DU (dBc) V CC = 3.0 V, Ta = -30°C, 25°C, 80°C Lo1: 178 MHz -25 dBm Lo2: 1619 MHz -20 dBm I, Q: 0.35 V[p-p] (Single phase)

1.6 VDC , p / 4

-80 -60 -50 -80 -90 -70 -40 -30 -70 -60 -50 -40 -30 -20 -10 2 3 ACP 30 kHz DU ACP 50 kHz PO 80°C 80°C 80°C -30°C -30°C -30°C -30°C, 25°C Circuit off 25°C 25°C 120 0 20 120 Mix. input level (dBmV) Mix. output level (dBmV) 100 110 40 60 80 100 V CC = 3.0 V Mix. in: 130 kHz Mix. out: 400 kHz Lo3 in: 129.6 MHz, 90 dBmV 80°C -30°C 25°C

AN6096FHN ICs for Mobile Communication n Application Circuit Example n Application Notes (continued)

• Main characteristics (continued) Note) Test conditions are the same as "n Electrical Characteristics" unless otherwise specified. The characteristic values below are theoretical values for designing and not guaranteed. Proximity spurious suppression RSSI characteristics 120 0 20 120 Lim. amp. input level (dBmV) Lim. amp. output level (dBmV) 100 110 40 60 80 100 V CC = 3.0 V Lim. in: 400 kHz Lim. out: 400 kHz -30°C 25°C, 80°C 0.0 3.0 0 20 120 Lim. amp. input level (dBmV) RSSI output voltage (V) 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8 40 60 80 100 V CC = 3.0 V Lim. in: 400 kHz Lim. out: 400 kHz -30°C 25°C, 80°C 824 2 200 pF V APC/BS 1.0 kW 2.0 kW V LI RSSIOUT V CC2 47 W 47 W 330 pF 100 pF Matsushita Electronic Components EHF FD1623 Lo1 Lo2 9I 23 10I 22 11Q 21 12Q 20 191 182 TXOUTPO V MX 173 164 MIXOUT155 LIMOUT V LM 633 nF 47 W 47 W 10 pF 15 nF137 15 nF 100 pF 100 nF 1 000 pF 1 000 pF Lo3 100 pF 100 pF 1 000 pF 1 000 pF 100 pF V MI V S 0.1 mF 4.7mF 330 pF 0.1 mF 3.3 mF 400 kHz filter 1 000 pF 1 000 pF 100 nF SW1 a b V CC1 IO IO IO IO RSSI