AN18207A

AN18207A PANASONIC

Document overview

• Manufacturer or author: Provided By digicamel.com
• PDF pages: 38

Technical content

Datasheet sections

1Publication date: July 2009 SDC00078AEB DATA SHEET Part No. Package Code No. AN18207A LQFP048-P-0707A

Tuner IC for home-audio stereo set „ Overview AN18207A is all-in-one IC for a radio of home-audio use. As for FM portion, FM MIX to FM MPX are integrated. As for AM portion, AM-RF to AM detector are integrated. FM/AM PLL synthesizer with pre-scale function is also integrated. Therefore, AN18207A can achieve the most function of radio. „ Features yAM : RF + MIX + L-OSC, FM : MIX + L-OSC, FM/AM : IF + DET, FM-MPX, PLL y I2C-bus control yFM detector coil less ySeparation adjustment free „ Applications yTuner, radio „ Package y48 pin Plastic Low Profile Quad Flat Package (QFP type) „ Type ySilicon Monolithic Bipolar IC

„ Application Circuit Example

„ Pin Descriptions Phase detector for MPX stereo detectorInput / OutputPD ST IND29 N.C. (Open in IC)—N.C.30 TUNED / Test monitor output / FM S-MeterOutputTUNED/Test/FM S- Meter21 N.C. (Open in IC)—N.C.20 N.C. (Open in IC)—N.C.19 N.C. (Open in IC)—N.C.18 N.C. (Open in IC)—N.C.17 Pulse input for ZAP (Must be open)—ZAP16 Serial data input / output (SDA)Input / OutputSDA15 Serial clock input (SCL)InputSCL14 VDD selectorInputVDD selector13 N.C. (Open in IC)—N.C.12 Phase detector for MPX-VCOInput / OutputPD MPXVCO28 AM AF inputInputAM AF IN27 FM/AM detector outputOutputFM/AM DET26 FM MPX inputInputFM MPX IN25 R-ch. de-emphasis output (External capacitor 0.0056 μF : Time constant = 50 μs)OutputRch OUT24 Stereo indicatorOutputST IND23 L-ch. de-emphasis output (External capacitor 0.0056 μF : Time constant = 50 μs)OutputLch OUT22 Crystal oscillatorInputXOSC111 Charge pump-VCCPower supplyVCC2 (CP)10 Charge pump outputOutputCPOUT9 Logic-GNDGroundGND (Logic)8 Logic-VCCPower supplyVCC (Logic)7 RF-GNDGroundRF-GND6 FM local oscillator load 1 (Base side)InputFM LOSC15 FM local oscillator load 2 (Emitter side)OutputFM LOSC24 FILTERInput / OutputFILTER3 FM mixer input 2InputFM MIXIN22 FM mixer input 1InputFM MIXIN11 DescriptionTypePin namePin No.

„ Pin Descriptions (continued) VCCPower supplyVCC31 GNDGroundGND32 AM IF amp. inputInputAM IF IN33 AM-AGC level detectorInput / OutputAM AGC34 AM mixer outputOutputAM MIX35 GND for IF amp.GroundGND46 RF-VCCPower supplyRF-VCC47 N.C. (Open in IC)—N.C.44 FM 2nd IF amp. inputInputFM 2IF IN45 FM detector bypass 2Input / OutputFMDETPASS241 N.C. (Open in IC)—N.C.42 AM local oscillator loadInput / OutputAM LOSC39 FM signal meter adjustmentInput / OutputFM SMADJ40 AM RF inputInputAM RF IN37 AM RF input reference biasInput / OutputAM RF BIAS38 MPX-VCO frequency adjustment / FM detector center adjustmentInput / OutputFMNUL/VCO36 N.C. (Open in IC)—N.C.43 FM mixer outputOutputFM MIXOUT48 DescriptionTypePin namePin No.

„ Operating supply voltage range 10.5VCC1 —mA60ICCSupply current2 NotesUnitRatingSymbolParameterA No. *3°C–55 to +150TstgStorage temperature5 *3°C–20 to +85ToprOperating ambient temperature4 *2mW294PDPower dissipation3 *1V 11.5VCC2 Supply voltage1 8.0 to 10.0VCC1 NotesUnitRangeSymbolParameter 8.0 to 11.0VCC2 Supply voltage range „ Absolute Maximum Ratings Note) Absolute maximum ratings are limit values which are not dest ructed, and are not the values to which operation is guaranteed. Notes) *1 : The values under the condition not exceeding the above absolute maximum ratings and the power dissipation. VCC2 is VCC for charge pump. *2 : The power dissipation shown is the value at T a = 85°C for the independent (unmounted) IC package without a heat sink. When using this IC, refer to the • PD-Ta diagram in the „ Technical Data and design the heat radiation with sufficient margin so that the allowable value might not be exceeded based on the conditions of power supply voltage, load, and ambient temperature. *3 : Except for the power dissipation, operating ambient temp erature, and storage temperature, all ratings are for Ta = 25°C. Note) * : The values under the condition not exceeding the above absolute maximum ratings and the power dissipation. VCC2 is VCC for charge pump.

„ Allowable Voltage Range Notes) Voltage values, unless otherwise specified, are with respect to GND. GND is voltage for RF-GND, GND(Logic), GND(IF), GND(IF AMP). RF-GND = GND(Logic) = GND(IF) = GND(IF AMP) Do not apply external currents or voltages to any pin not specifically mentioned. Please make Pin16 open. For the circuit currents, "+" denotes current flowing into the IC, and "−" denotes current flowing out of the IC. —V– 0.3 to (VCC1 +0 . 3 )PD ST IND29 —V– 0.3 to (VCC1 +0 . 3 )PD MPXVCO28 —V– 0.3 to (VCC1 +0 . 3 )AM AF IN27 —V– 0.3 to (VCC1 +0 . 3 )FM MPX IN25 —V− 0.3 to 5.3SDA15 —V− 0.3 to 5.3SCL14 —V– 0.3 to (VCC1 +0 . 3 )VDD selector13 —V– 0.3 to (VCC1 +0 . 3 )XOSC111 —V– 0.3 to (VCC1 +0 . 3 )FM LOSC15 —V– 0.3 to (VCC1 +0 . 3 )FILTER3 —V– 0.3 to (VCC1 +0 . 3 )FM MIXIN22 —V– 0.3 to (VCC1 +0 . 3 )AM RF IN37 —V– 0.3 to (VCC1 +0 . 3 )FMNUL/VCO36 —V– 0.3 to (VCC1 +0 . 3 )AM AGC34 —V– 0.3 to (VCC1 +0 . 3 )AM IF IN33 —V– 0.3 to (VCC1 +0 . 3 )FMDETPASS241 —V– 0.3 to (VCC1 +0 . 3 )FM SMADJ40 —V– 0.3 to (VCC1 +0 . 3 )AM LOSC39 —V– 0.3 to (VCC1 +0 . 3 )AM RF BIAS38 —V– 0.3 to (VCC1 +0 . 3 )FM 2IF IN45 – 0.3 to (VCC1 +0 . 3 )FM MIXIN1 NotesUnitRatingPin namePin No. —V1

—dB—7454 VIN2 = 80 dBμ, 1 kHz, 100% output ratio to fmVo (mute on) fmMUTEFM-mute ratio16 —dBμ5141310% mod Sens set (I2C) = X'5'fmSDSFM-SD sensitivity15 —%1.30.2—VIN2 = 80 dBμ, 1 kHz, 100% output distortion factorfmTm1FM-mono THD14 —mV[rms]640480320VIN2 = 80 dBμ, 1 kHz, 100%fmRDSFM-RDS output9 FM mono fc = 10.7 MHz *1mA584736No input, Current supplied from VCC1 fmIt1FM-quiescent current 110 *1μA16010553No input, Current supplied from VCC2 fmIt2FM-quiescent current 211 —mV[rms]1 000800600VIN2 = 80 dBμ, 1 kHz, 100% outputfmVoFM output12 —dB—7268VIN2 = 100 dBμ, 1 kHz, 100% FM output S/NfmSNFM-S/N ratio13 —dBμ5343330% mod Sens set (I2C) = X'C'amSDSAM-SD sensitivity8 —%2.00.5—VIN3 = 103 dBμ, 1 kHz, 30% output distortion factor amT2AM THD 27 VIN3 = 74 dBμ, 1 kHz, 30% output distortion factor VIN3 = 30 dBμ, 1 kHz, 30% AM output S/N VIN3 = 74 dBμ, 1 kHz, 30% AM output VIN3 = 30 dBμ, 1 kHz, 30% AM output —mV[rms]288208128amVo2AM output 23 —dB—2317amSN1AM-S/N ratio 14 —dB—5347VIN3 = 74 dBμ, 1 kHz, 30% AM output S/NamSN2AM-S/N ratio 25 AM fc = 999 kHz *1mA422814No input, Current from VCC1 amItAM-quiescent current1 —mV[rms]1729252amVo1AM output 12 —%1.10.4—amT1AM THD 16 Limits Typ Unit Max Notes Min ConditionsSymbolParameterB No. „ Electrical Characteristics at VCC1 = 9.0 V, VCC2 = 10 V Note) T a = 25°C±2°C unless otherwise specified. Note) *1 : No input = –10 dBμ or less.

FM FE fc = 98 MHz —dB—3928VIN1 = 12 dBμ, 1 kHz, 100% mod VODET fmSNFM-FE S/N ratio22 —mV[rms]10.08.26.4VIN1 = 64 dBμ, IFOUTfmMIXoutFM-Mixer output level23 —mV[rms]345280215No input, 108.7 MHzfmOSCoutFM-LOSC level24 FM mono fc = 10.7 MHz —dBμ3726—1 kHz, 100% of output –3 dB (Ref. input level VIN2 = 80 dBμ)fmVlimFM limiting sensitivity25 —dB—6854 VIN2 = 100 dBμ, fm = 1 kHz AM : 30% mod FM : 100% mod AMRAM suppression ratio26 —%5.03.01.3VIN2 = 80 dBμ, fp = 19 kHz fmSTONFM-stereo detect sensitivity21 FM stereo fc = 10.7 MHz —dB——20pilot = 10% output levelfmCLFM-carrier-leak20 —%1.50.35— VIN2 = 80 dBμ, 1 kHz, stereo (L + R) 90% output distortion factor fmTs1FM-stereo THD19 —dB—4030VIN2 = 80 dBμ, 1 kHz, 90% R-ch. output separationfmSepRFM-R-ch. separation18 —dB—4030VIN2 = 80 dBμ, 1 kHz, 90% L-ch. output separation fmSepLFM-L-ch. separation17 Limits Typ Unit Max Notes Min ConditionsSymbolParameterB No. „ Electrical Characteristics (continued) at VCC1 = 9.0 V, VCC2 = 10 V Note) T a = 25°C±2°C unless otherwise specified.

—V0.4—0VDD > 2 V IP50 = 3 mAVOL1Low-level output voltage 130 —V0.9—–0 . 5 Voltage which recognized that SDA and SCL are Low-level

3 V mode Pin 13 : OPEN

V ILO_3Low-level input voltage 234 —V3.5—2.1 Voltage which recognized that SDA and SCL are High-level V IHI_3High-level input voltage 233 —V1.5—–0 . 5 Voltage which recognized that SDA and SCL are Low-level

5 V mode Pin 13 : GND

V ILO_5Low-level input voltage 132 —V5.5—3.5 Voltage which recognized that SDA and SCL are High-level V IHI_5High-level input voltage 131 —V0.4—0ACK Pin 15 voltage I = 3 mAVACKACK Low-level output voltage29 I2C interface —μA–72–120–170120 μA mode Pin 9 input currentIcpdownCharge pump output pull-down current28 —μA17012990120 μA mode Pin 9 output currentIcpupCharge pump output pull-up current27 PLL Reference values Typ Unit Max Notes Min ConditionsSymbolParameterB No. „ Electrical Characteristics (Reference values for design) at VCC1 = 9.0 V , VCC2 = 10 V Notes) T a = 25°C±2°C unless otherwise specified. The characteristics listed below are reference values derived from the design of the IC and are not guaranteed by inspection. If a problem does occur related to these characteristics, we will respond in good faith to user concerns.

„ Electrical Characteristics (Reference values for design) (continued) at VCC1 = 9.0 V , VCC2 = 10 V Notes) T a = 25°C±2°C unless otherwise specified. The characteristics listed below are reference values derived from the design of the IC and are not guaranteed by inspection. If a problem does occur related to these characteristics, we will respond in good faith to user concerns. *2ns250⎯20 + 0.1Cb Bus capacitance : 10 pF to 400 pF Ip < 6 mATofOutput fall time from V IHmin to VILmax38 *2ns300⎯20 + 0.1Cb ⎯trRise time of both SDA and SCL signals47 *2ns⎯⎯100⎯tSU:DATData set-up time46 *2μs⎯⎯0.6⎯tSU:STA Set-up time for a repeat START condition44 *2pF400⎯⎯⎯CbCapacitive load for each bus line51 *2μs⎯⎯1.3⎯tBUF Bus free time between a STOP and START condition50 *2μs⎯⎯0.6⎯tSU:STOSet-up time of STOP condition49 *2ns300⎯20 + 0.1Cb ⎯tfFall time of both SDA and SCL signals48 *2μs⎯⎯1.3⎯tLOWLow period of the SCL clock 42 *2μs0.9⎯0⎯tHD:DATData hold time45 *2μs⎯⎯0.6⎯tHIGHHigh period of the SCL clock43 The first clock pulse is generated after tHD:STA Bus capacitance : 10 pF to 400 pF *2V——0.153 V mode Pin 13 : OPENVhys2Hysteresis of Schmitt trigger inputs 137 *2ns50—0—tSP Pulse width of spikes which must be suppressed by the input filter39 *2pF10——CiCapacitance for each I/O pin40 I2C Interface (Fast-mode) *2kHz400———fSCLSCL maximum frequency35 *2V——0.25Vhys1Hysteresis of Schmitt trigger inputs 136 *2μs——0.6tHD:STAHold time (repeated)41 Reference values Typ Unit Max Notes Min ConditionsSymbolParameterB No.

„ Electrical Characteristics(Reference values for design)(continued)at VCC1 = 9 V, VCC2 = 10 V Notes) T a = 25°C±2°C unless otherwise specified. The characteristics listed below are reference values derived from the design of the IC and are not guaranteed by inspection. If a problem does occur related to these characteristics, we will respond in good faith to user concerns. S : START condition Sr : Repeat START condition P : STOP condition SCL SDA tLOW tf tr tHD:STA tHD:DAT tHIGH tSU:DAT tf tSU:STA tHD:STA tSP Sr tSU:STO tBUF PS tr Notes) *2 : The timing of Fast-mode devices in I 2C-bus is specified as above. *2μA10⎯–10VIN = 0.5 V to 4.5 VIi5Input current each I/O pin at 5V mode56 *2V⎯⎯0.63 V mode Pin 13 : OPENVaH2 Noise margin at the High-level for each connected device55 *2V⎯⎯0.55 V mode Pin 13 : GNDVaL1 Noise margin at the Low-level for each connected device52 *2V⎯⎯1.05 V mode Pin 13 : GNDVaH1 Noise margin at the High-level for each connected device53 *2μA10⎯–10VIN = 0.3 V to 2.7 VIi3Input current each I/O pin at 3V mode57 *2V⎯⎯0.33 V mode Pin 13 : OPENVaL2 Noise margin at the Low-level for each connected device54 I2C Interface (Fast-mode) (continued) Reference values Typ Unit Max Notes Min ConditionsSymbolParameterB No.

„ Electrical Characteristics Test Procedures

221210 V9 V30 kHz LPF22

f = 10.7 MHz, VIN2 = 80 dBμ fs = 1 kHz, FM : 100% mod2FM-mute ratio16 221210 V9 V27 kΩ pull-up21f = 10.7 MHz, 0 % mod2FM-SD sensitivity15 221210 V9 V30 kHz LPF24f = 10.7 MHz, VIN2 = 80 dBμ, fs = 1 kHz, FM : 100% mod2FM-mono THD14

221210 V9 V30 kHz LPF24

f = 10.7 MHz, VIN2 = 100 dBμ, FM : 100% L-ch S/N 2FM-S/N ratio13 221210 V9 V30 kHz LPF24f = 10.7 MHz, VIN2 = 80 dBμ, fs = 1 kHz, FM : 100% mod2FM output12

221210 V9 V——No signal—FM-quiescent current 211

221210 V9 V——No signal—FM-quiescent current 110

221210 V9 V30 kHz LPF26VIN2 = 80 dBμ, fs = 1 kHz

FM : 100% mod2FM-RDS output9 FM mono

221210 V9 V27 kΩ pull-up21f = 999 kHz, AM : 0% mod37AM-SD sensitivity8

221210 V9 V30 kHz LPF22f = 999 kHz, VIN3 = 110 dBμ,

fs= 1 kHz, AM : 30% mod37AM THD 27

221210 V9 V30 kHz LPF22f = 999 kHz, VIN3 = 74 dBμ

fs = 1 kHz, AM : 30% mod37AM THD 16 fs = 1 kHz, AM : 30% S/N37AM-S/N ratio 25

221210 V9 V30 kHz LPF22f = 999 kHz, VIN3 = 30 dBμ

fs = 1 kHz, AM : 30% S/N37AM-S/N ratio 14 fs= 1 kHz, AM : 30% mod37AM output 23 fs = 1 kHz, AM : 30% mod37AM output 12 AM SW4 SW3 SW2 SW1 10 V VCC2 9 V VCC1 Pin settings Pin No. Output Conditions Input No signal Conditions —AM-quiescent current1 Pin No. ParameterC No.

„ Electrical Characteristics Test Procedures (continued)

221210 V9 V27 kΩ pull-up12

f = 10.7 MHz, VIN2 = 80 dBμ, fs = 19 kHz VIN2FM-stereo detect sensitivity21

221110 V9 V30 kHz LPFVO

f = 98 MHz, VIN1 = 12 dBμ, 1 kHz, 100% mod VIN1FM-FE S/N ratio22 FM FE fc = 98 MHz

221210 V9 V—VF

MOSNo input, f = 108.7 MHz—FM-LOSC level24

221210 V9 V—IF

f = 98 MHz, VIN3 = 64 dBμ, 0% modVIN1FM-IF output level23 FM mono fc = 10.7 MHz

221210 V9 V30 kHz LPFVOL

1 kHz, 100% of output –3 dB (Ref. input level V IN2 = 80 dBμ) VIN2FM limiting sensitivity25 VIN2 = 100 dBμ, fm = 1 kHz, AM : 30% mod FM : 100% mod V IN2AM suppression ratio26

221210 V9 V―VOL

f = 10.7 MHz, VIN2 = 80 dBμ, fs = 19 kHz (pilot = 10%) VIN2FM-carrier-leak20

111210 V9 V15 kHz LPF22

f = 10.7 MHz, VIN2 = 80 dBμ, 1 kHz (L + R = 90%, pilot = 10%) 2FM-stereo THD19

111210 V9 V15 kHz LPF24

f = 10.7 MHz, VIN2 = 80 dBμ, 1 kHz (R = 90%, pilot = 10%) 2FM-R-ch. separation18 FM stereo SW4 SW3 SW2 SW1 10 V VCC2 9 V VCC1 Pin settings Pin No. Output 15 kHz LPF Conditions Input f = 10.7 MHz, VIN2 = 80 dBμ, 1 kHz, (L = 90%, pilot = 10%) Conditions 2FM-L-ch. separation17 Pin No. ParameterC No.

x This IC, I2C-bus, is designed to correspond to the Standard-mode (100 kbps) and Fast-mode (400 kbps) devices in the version x This IC will be operated as a slave device in the I2C-bus system. x The program operation check of this IC has not been conducted on the multi-master bus system and the mix-speed bus system, yet. The connected confirmation of this IC to the CBUS receiver also has not been checked. Please confirm our company if it will be used in these mode systems. x Purchase of Panasonic I2C Components conveys a license under the Philips I2C patent right to use these components in an I2C systems, provided that the system conforms to the I2C standard specifications as defined by Philips. 2. START and STOP conditions A High to Low transition on the SDA line while SCL is High is one such unique case. This situation indicates a START condition. A Low to High transition on the SDA line while SCL is High defines a STOP condition. START and STOP conditions are always generated by the master. The bus is considered to be free again a certain time after the STOP condition. Every byte put on the SDA line must be 8-bits long. The number of bytes that can be transmitted per transfer is unrestricted. Each byte has to be followed by an acknowledge bit. Data is transferred with the most significant bit (MSB) first. If a slave can't receive or transmit another complete byte of data until it has performed some other function, for example servicing an internal interrupt, it can hold the clock line SCL Low to force the master into a wait state. Data transfer then continues when the slavei s ready for another byte of data and releases clock line SCL. „ Technical Data yI2C-bus interface 1. Basic Rules 3. Transferring Data SCL SDA acknowledgement signal from slave acknowledgement signal from receiver START or repeated START condition STOP or repeated START condition START condition STOP condition SDA SCL MSB ACK ACK 1 2 7 8 9 1 2 3 – 8 9 Sr or P Sr P S or Sr

„ Technical Data (continued) yI2C-bus interface (continued) 4. DATA format 1) Write mode 1.1) Slave address : 1011 0110 (B6H) 1.2) Format x Data update mode x Auto-increment mode 2) Read mode 2.1) Subaddress : None 2.2) Slave address : 1011 0111 (B7H) 2.3) Format STOP condition AckSTART condition Read Mode : 1 Data byteSlave address P AARS Ex.) In case data is read from Address 01h after data is written to Address 01h. x Write x Read Data byteSub address 01hSlave address A P AA0S Data byteSlave address P AA1S STOP condition AckSTART condition Write Mode : 0 Data byteSub addressSlave address A P AAWS Data nAAData 1 Data 2Sub addressSlave address A P AAWS

———— CIS selection (CIS) Mixer AGC (MXAGC)———— AM IF AMP Stop (D070) —07 Adjustment Mode: MPX Separation Adjustment / Write Mode (SE2 - SE1) Adjustment Mode (EMU) Read / Write Mode (ZRW) Adjustment Mode: FM Detector Adjustment / Write Mode (DE5 - DE0)05 —06 Charge Pump Control (PHD1 - PHD0) PLL-N Divider (N13 - N8) FM/AM Switch (DSS0) Force Monaural (FOM) Stereo Tuning Selector (TUS) Mute ON/OFFMA TX (MUS) CP Select (FCPS) PLL-Ref Frequency Select (RO) Analog/Logic Signal Monitor (DS3 - DS0) L-OSC Stop (VMOS3) FM IF AMP STOP (LIMSTOP) —03 PLL-N Divider (N7 - N0)02 SD Mode Switch (SDS) AM SD Hysteresis Control (AMHIS) FM and SD Tuned Level Adjust (DSS4 - DSS0) PLL-CP Current Select (ICO) D0D1D2D3D4D5D6D7 LSBDATA BYTEMSBSub Address „ Technical Data (continued) y I2C-bus interface (continued) 5. Register Map

PLL-charge pump current select 120 μA → Fast lock up time 30 μA → S/N improvement Normal : 120 μA ICOMSB : D7 —D6 Don't care (0/1) —D5 DSS4D4 DSS3D3 DSS2D2 DSS1D1 FM and AM-SD tuned level adjust Be sure to set it when you change FM / AM. High : Sensitivity low Low : Sensitivity high This sensitivity is affected by an external RF amp. gain. Ex.) FM : X'5' AM : X'C' It is recommended to set "0" for DSS4. DSS0LSB : D0 FunctionNameBit Tuner-control (Group 1) SUB-ADD 00H (Write) 301 1200 Icp [μA]ICO „ Technical Data (continued) y I2C-bus interface (continued) 6. Sub address byte and data byte format (Write mode)

1 : AM-SD hysteresis ONAMHISMSB : D7 PLL-reference frequency selector ROD6 FM mode & SDS OFF 0 : CP 30 μAf i x e d 1 : CP selectable (SUB-ADD 00H D7) FCPSD5 Mute switch 1 : ON Output AF buffer amp. mute MUSD4 Selector to force monaural when stereo indicator is off. 0 : ON 1 : OFFTUSD3 Force monaural 1 : monaural SUB detection and VCO stop. So IC is changed to monaural mode FOMD2 SD mode switch (FM / AM IF counter) 1 : SD mode (IF counter : ON) AM AGC-time-constant select 0 : 500 kΩ 1 : 10 kΩ IF counter is activated by setting this bit to "1" at I2C stop condition. And an inside impedance of AM-AGC is changed at AM. A time constant becomes 1/50 in the case of "1". *1) SDSD1 FM / AM switch 0 : FM 1 : AMFASLSB : D0 FunctionNameBit Tuner-control (Group 2) SUB-ADD 01H (Write) 9 kHz50 kHz1 10 kHz25 kHz0 AMFMRO „ Technical Data (continued) y I2C-bus interface (continued) 6. Sub address byte and data byte format (Write mode) (continued) Note) *1 : When SDS mode is ON and stop condition of I 2C comes, IF count is carried out . After 70 ms of Stop condition, a result is ready to read.

N7MSB : D7 N6D6 N5D5 N4D4 N3D3 N2D2 N1D1 PLL-N divider N-divider FM : N = 213 × N13 + 212 × N12 + 211 × N11 + ··· + 20 × N0 AM : N = 29 × N13 + 28 × N12 + 27 × N11 + ··· + 20 × N4 (Not use N0 to N3 at AM mode.) N0LSB : D0 FunctionNameBit Tuner-control (Group 2) SUB-ADD 02H (Write) —MSB : D7 —D6 N13D5 N12D4 N11D3 N10D2 N9D1 PLL-N divider N-divider FM : N = 213 × N13 + 212 × N12 + 211 × N11 + ··· + 20 × N0 AM : N = 29 × N13 + 28 × N12 + 27 × N11 + ··· + 20 × N4 (Not use N0 to N3 at AM mode.) N8LSB : D0 FunctionNameBit Tuner-control (Group 2) SUB-ADD 03H (Write) „ Technical Data (continued) y I2C-bus interface (continued) 6. Sub address byte and data byte format (Write mode) (continued)

0 : FM IF amp. stop (Pin 10 Low)LIMSTOPMSB : D7 1 : L-OSC stopVMOS3D6 PHD1D5 Charge pump control PHD0D4 DS3D3 DS2D2 DS1D1 Analog / logic signal monitor DS0LSB : D0 FunctionNameBit Tuner-control (Group 3) SUB-ADD 04H (Write) Monitor of the hysteresis DC voltage of AM-SD indicator1111 NIFC1110 F4501101 RED output1100 ANC output1011 PS output1010 Monitor of MPX-VCO1001 AM S-Meter1000 FM S-Meter0111 Monitor of SD-ON level adjustment DAC output0110 Monitor of the hysteresis DC voltage of stereo indicator0101 Monitor of the hysteresis DC voltage of FM-SD indicator0100 Monitor of FM separation adjustment DAC output0011 Monitor of FM detector adjustment DAC output0010 Monitor of FM detector reference voltage0001 Monitor OFF0000 Monitor pointDS3DS2DS1DS0 Hi-Z mode11 Force down10 Force up01 Normal mode00 Charge pump controlPHD1PHD0 „ Technical Data (continued) y I2C-bus interface (continued) 6. Sub address byte and data byte format (Write mode) (continued)

At adjustment mode : FM detector adjustment At write mode : 1 : Writing bit Read / write mode 0 : Read 1 : Write DE5MSB : D7 DE4D6 DE3D5 DE2D4 DE1D3 DE0D2 ZRWD1 Adjustment mode 1 : ONEMULSB : D0 FunctionNameBit Tuner-control (Group 3) SUB-ADD 05H (Write) Set them "0" all. —MSB : D7 —D6 —D5 —D4 —D3 SE2D2 SE1D1 At adjustment mode : MPX separation adjustment At write mode : 1 : Writing bit SE0LSB : D0 FunctionNameBit Tuner-control (Group 3) SUB-ADD 06H (Write) „ Technical Data (continued) y I2C-bus interface (continued) 6. Sub address byte and data byte format (Write mode) (continued)

1 : AM IF amp. stopD070LSB : D0 0 : FM IF counter band width = 40 kHz, 1 : FM IF counter band width = 10 kHzCISD1 0 : Mixer AGC off, 1 : Mixer AGC onMXAGCD2 Set them "0" all. —MSB : D7 —D6 —D5 —D4 —D3 FunctionNameBit Tuner-control (Group 3) SUB-ADD 07H (Write) „ Technical Data (continued) y I2C-bus interface (continued) 6. Sub address byte and data byte format (Write mode) (continued)

D1 to D7 = 1 —MSB : D7 —D6 —D5 —D4 —D3 —D2 —D1 IF counter output 0 : No signal AM IF C band width = 4 kHz, FM IFC band width = 40 kHz, or 10 kHzIFCLSB : D0 FunctionNameBit Tuner-control (Group 4) SUB-ADD none (Read) „ Technical Data (continued) y I2C-bus interface (continued) 7. Data byte format (Read mode)

„ Technical Data (continued) y I2C-bus interface (continued) 8. Precaution in setup of I2C-bus data Wait time Gate time reset Start (stop condition) Access prohibition time : More than 70 ms. (Reference value) 1) Power on a) All data must be set on IC when the pow er supply is tuned on. (SUB ADD : 00H to 07H) b) IF limit amplifier must be ON at the time of the initial data transfer of I 2C. (SUB ADD : 04H, D7 = "1") c) The power supply transition time (V CC1, 2 = 0 → 9 V) must be more than 10 ms. d) Electric current flows in the power supply off condition when a power supply is connected to the TUNED terminal (Pin 21). Therefore, be careful in the case of the backup mode such as a microcomputer. 2) Pin 16 Don't use Pin 16 (ZAP). It must be open. 3) Monitor function a) Pin 21 of this IC has a function to monitor internal circuit terminals of this IC. The monitor point of analog signal or digital signal is set by SUBADD : 04H, D0 to D3. The choice of monitor point of logic signal is SUBADD : 0AH .It is chosen by D0 to D2 of 0AH. b) Don't choose more than one monitor poi nt (analog, logic) at the same time. c) It is prohibited choosing the mon itor point when IF limit amplifier is compulsory off (SUBADD : 04H, D7 = "0"). Be sure to turn on IF limit amplifier when you use monitor function. d) Monitor function is a function for the test purpose onl y in our company, and its function is not guaranteed. When it is needed to send data, all data must be "0". Don't use it with the actual tuner set. 4) Charge pump test function a) SUBADD : 04H D4 to D5 are the bits fo r the function check of charge pump. For a normal use, they must be set to "0". 5) Handling unused bits a) All unused bits must be set to "0". Wh en it is necessary to input Subaddress data, all unused bits must be set to "0". 6) Set number of N divider Don't establish N value about settlement of N divider in 271 or less. 7) The timing of IF counter IF counter starts to count when it detects Stop condition of write mode at SDS mode (SUB ADD : 01H, D1 = "1"). The result of the IF count can get it when it begins to read it after the progress about more than 70 ms and it is made the mode and begins to read it. To prevent IF counter’s abnormal function, so that stop condition may not come between about 70 ms of the following. (see the figure below.) Even if this timing isn't kept, IC doesn't become uncontrollable. But the following condition are occurred by the transmitting data. a) When there are data which turn off SDS : Counter stops, and it is reset. The judgment result of IF counter isn't right. Ignore data and erase it. b) In the case of the dummy data: Stop condition is ignored, and IF counter works as it is. (It isn't reset.) If an original access prohibition time passes, the proper result of IF counter is obtained.

FM IF amp. input330 Ω (AC input)45 FM detector bypass 2 External capacitor = 0.1 μF4 kΩ1.9 V41 N.C.—OPEN—42 to RF-VCC——47 GND (IF amp)———46 Impedance DescriptionInternal circuitWaveform and voltage Pin No. GND GND 12k VCC 2.3 V

10.7 MHz

14.6k 20.4k 4.2 V GND VCC GND 12k 330 „ Technical Data (continued) yI/O block circuit diagrams and pin function descriptions Note) The characteristics listed below are reference values derived from the design of the IC and are not guaranteed. 100 μA GND VCC

FM mixer output500 Ω to High f = fOSC –f RF or f = fRF –f OSC FM mixer input400 Ω (f = 100 MHz) Impedance DescriptionInternal circuitWaveform and voltage Pin No. 2.3 V GND GND 12k GND GND 12k VCC GND GND 12k VCC 2.2k 2.2k f = fmRF „ Technical Data (continued) yI/O block circuit diagrams and pin function descriptions (continued) Note) The characteristics listed below are reference values derived from the design of the IC and are not guaranteed.

FM local oscillator load 1 (Base side) 3.9 kΩ5 RF-GND———6 FM AGC FILTER External capacitor = 0.1 μF1 kΩ1.9 V3 FM L-OSC2 FM local oscillator load 2 (Emitter side) Low4 Impedance DescriptionInternal circuitWaveform and voltage Pin No. GND VCC DC 300 μA 3.9k 3.9 V VCC GND GND 12k VCC GND GND 12k „ Technical Data (continued) yI/O block circuit diagrams and pin function descriptions (continued) Note) The characteristics listed below are reference values derived from the design of the IC and are not guaranteed.

N.C.—OPEN—12 Crystal oscillator120 Ω11 VCC2 Charge pump-VCC —DC10 CPOUT Charge pump outputHighDC9 GND for Logic and Charge pump———8 VCC for Logic—DC7 Impedance DescriptionInternal circuitWaveform and voltage Pin No. GND 12k GND GND GND 12k

10 VCC2

400 μA 11 50 GND 12kGND VCC Phase DET VCC GND GND 12k „ Technical Data (continued) yI/O block circuit diagrams and pin function descriptions (continued) Note) The characteristics listed below are reference values derived from the design of the IC and are not guaranteed.

N.C.—OPEN—17 to ZAP (Must be open.)——16 SDA Serial data input / outputHigh15 SCL Serial clock inputHigh14 VDD selector103 kΩ—13 Impedance DescriptionInternal circuitWaveform and voltage Pin No. 102k102kGND GND 12k 102k102k GND 12k GND 12k GND 102k 1.05k 3 V GND GND 12kGND „ Technical Data (continued) yI/O block circuit diagrams and pin function descriptions (continued) Note) The characteristics listed below are reference values derived from the design of the IC and are not guaranteed.

R-ch. de-emphasis output (External capacitor 0.0056 μF Time constant = 50 μs) 8.4 kΩDC bias = 3.5 V24 FM MPX input500 kΩComposite signal25 FM/AM detector output (Please make it to OPEN when unused.) 200 Ω—26 L-ch. de-emphasis output (External capacitor 0.0056 μF Time constant = 50 μs) 8.4 kΩDC bias = 3.5 V22 AM AF input11 kΩ27 ST-OUT FM stereo indicator1k Ω—23 TUNED/Test SD-OUT FM/AM tuning indicator Test monitor output 1k Ω—21 Impedance DescriptionInternal circuitWaveform and voltage Pin No. GND 12k GND GND GND 12k AM-AF 10k 3.5 V 1.05k GND 498k 3.5 V 1.05k GND AM-DET FM-DET 205 GND GND 12k 1.05k GND VCC GND 7.35k 1.05k GND VCC GND 7.35k „ Technical Data (continued) yI/O block circuit diagrams and pin function descriptions (continued) Note) The characteristics listed below are reference values derived from the design of the IC and are not guaranteed.

Stereo DET of MPX214 kΩDC ≅ VCC1 – 1.4 V29 Phase detector for MPX-VCO46 kΩ DC ≅ VCC1 – 1.4 V28 Impedance DescriptionInternal circuitWaveform and voltage Pin No. 46k 46k GND 1.05k1k 214k 214k GND 1.05k1k „ Technical Data (continued) yI/O block circuit diagrams and pin function descriptions (continued) Note) The characteristics listed below are reference values derived from the design of the IC and are not guaranteed.

AM mixer outputHighf = fOSC –f RF35 AM-AGC level detector51 kΩ / 501 kΩDC34 AM IF amp. input3.3 kΩ33 GND—―—32 VCC——31 N.C.—OPEN—30 Impedance DescriptionInternal circuitWaveform and voltage Pin No. GND GND 12k GND 12k GND 12k 500k 50k at SDS ON AM DET GND 1.05k 1.05k f = 450 kHz 2 V 3.1k

2 V12k

„ Technical Data (continued) yI/O block circuit diagrams and pin function descriptions (continued) Note) The characteristics listed below are reference values derived from the design of the IC and are not guaranteed.

VCO adjustment1 kΩ—36 FM signal meter adjustment23 kΩ—40 AM L-OSC AM local oscillator load—39 AM RF inputHigh37 AM RF reference1 kΩ—38 Impedance DescriptionInternal circuitWaveform and voltage Pin No. 522 kHz – 1 720 kHz 1 mA GND GND 12k VCC 250 250 GND GND 12k VCC 22k 5 V GND 1.05k 2 V GND DC 30 mA 480 mA GND 12k GND „ Technical Data (continued) yI/O block circuit diagrams and pin function descriptions (continued) Note) The characteristics listed below are reference values derived from the design of the IC and are not guaranteed.

„ Technical Data (continued) y PD ⎯ Ta diagram

y Special attention and precaution in using 1. This IC is intended to be used for ge neral electronic equipment [Home audio tuner]. Consult our sales staff in advance for information on the following applications: x Special applications in which exceptional quality and reliability are required, or if the failure or malfunction of this IC may directly jeopardize life or harm the human body. x Any applications other than the standard applications intended. (1) Space appliance (such as artificial satellite, and rocket) (2) Traffic control equipment (such as for automobile, airplane, train, and ship) (3) Medical equipment for life support (4) Submarine transponder (5) Control equipment for power plant (6) Disaster prevention and security device (7) Weapon (8) Others : Applications of which reliability equivalent to (1) to (7) is required 2. Pay attention to the direction of LSI. When mounting it in the wrong direction onto the PCB (printed-circuit-board), it might smoke or ignite. 3. Pay attention in the PCB (printed-circuit-board) pattern layout in order to prevent damage due to short circuit between pins. In addition, refer to the Pin Description for the pin configuration. 4. Perform a visual inspection on the PCB be fore applying power, otherwise damage might happen due to problems such as a solder- bridge between the pins of the semiconductor device. Also, perform a full technical verification on the assembly quality, because the same damage possibly can happen due to conductive substances, such as solder ball, that adhere to the LSI during transportation. 5. Take notice in the use of this product that it might break or occasionally smoke when an abnormal state occurs such as output pin- V CC short (Power supply fault), output pin-GND short (Ground fault), or output-to-output-pin short (load short) . And, safety measures such as an installation of fuses are recommended because the extent of the above-mentioned damage and smoke emission will depend on the current capability of the power supply. And IC is destroyed under the conditions listed below, (1) VCC2 and Pin5 are shorted. (2) VCC2 and Pin22 are shorted. (3) VCC2 and Pin45 are shorted. 6. When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions (operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any defect which may arise later in your equipment. Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. 7. When using the LSI for new models, verify the safe ty including the long-term reliability for each product. 8. When the application system is designed by using this LSI, be sure to confirm notes in this book. Be sure to read the notes to descriptions and the usage notes in the book. „ Usage Notes

Request for your special attention and precautions in using the technical information and semiconductors described in this book (1) If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and regulations of the exporting country, especially, those with regard to security export control, must be observed. (2) The technical information described in this book is intended only to show the main characteristics and application circuit examples of the products. No license is granted in and to any intellectual property right or other right owned by Panasonic Corporation or any other company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other company which may arise as a result of the use of technical information described in this book. (3) The products described in this book are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances). Consult our sales staff in advance for information on the following applications: – Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the prod- ucts may directly jeopardize life or harm the human body. – Any applications other than the standard applications intended. (4) The products and product specifications described in this book are subject to change without notice for modification and/or im- provement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to make sure that the latest specifications satisfy your requirements. (5) When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions (operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any defect which may arise later in your equipment. Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (6) Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS, thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages. (7) This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of our company. 20080805