Datasheet search site
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 4
Technical content
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20211117 (1/4) inductor_automotive_power_bcl322515rt-d_en.fm INDUCTORS Inductors for power circuits Wound metal BCL series (for automotive) BCL322515RT-D type
FEATURES
The adoption of the new method has resulted in a high inductance that could not be achieved with conventional metallic material s. Due to the properties of metallic materials, they are more able to handle larger currents than ferrite materials. The use of high-µ materials has made it possible to achieve low Rdc in metal products. The coil is fully encapsulated with a magnetic material to minimize leakage flux. Supports rated voltage of 40V . Operating temperature range: –55 to +155°C (including self-temperature rise) Compliant with AEC-Q200. APPLICATION ADAS - Level5 for Camera PART NUMBER CONSTRUCTION CHARACTERISTICS SPECIFICATION TABLE Rated current: smaller value of either Isat or Itemp. Isat: When based on the inductance change rate (30% below the nominal value) Itemp: When based on the temperature increase (temperature increase of 40°C by self heating) Measurement equipment ˎEquivalent measurement equipment may be used. BCL 322515 RT - 470 M - D Series name LxWxH dimensions Internal code Inductance Inductance tolerance Internal code3.2x2.5x1.5 mm (µH) L Measuring frequency DC resistance Rated current Isat Itemp Part No. Measurement item Product No. Manufacturer L E4990A Keysight Technologies DC resistance AX-114N ADEX REACH SVHC-Free Lead FreeRoHS Pb Halogen Free BrCl AEC-Q200
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20211117 (2/4) inductor_automotive_power_bcl322515rt-d_en.fm INDUCTORS BCL322515RT-D type L FREQUENCY CHARACTERISTICS Measurement equipment ˎEquivalent measurement equipment may be used. L VS. DC BIAS CHARACTERISTICS Measurement equipment ˎEquivalent measurement equipment may be used. Product No. Manufacturer E4990A Keysight Technologies Product No. Manufacturer 6500B KUWAKI ELECTRONICS Inductance(µH) Frequency(MHz) 0.1 100 1000 0.1 1 10 100 470M 330M 220M 150M 100M 6R8M 4R7M Inductance(µH) DC current(A) 0 0.5 1 1.5 2 2.5 470M 330M 220M 150M 100M 6R8M 4R7M
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20211117 (3/4) inductor_automotive_power_bcl322515rt-d_en.fm INDUCTORS BCL322515RT-D type SHAPE & DIMENSIONS RECOMMENDED LAND PATTERN RECOMMENDED REFLOW PROFILE PACKAGING STYLE REEL DIMENSIONS TAPE DIMENSIONS PACKAGE QUANTITY TEMPERATURE RANGE, INDIVIDUAL WEIGHT Operating temperature range includes self-temperature rise. Dimensions in mm 2.5±0.2 2.5±0.2 1.5max. 1.0 1.6 1.0 2.5 Dimensions in mm Natural cooling 5s max. 60 to 120s Preheating 10 to 30s Soldering 230°C 230°C 245°C 180°C 150°C Time Peak Temperature Type A B K Package quantity 2000 pcs/reel Operating temperature range Storage temperature range Individual weight –55 to +155 °C –55 to +155 °C 0.067 g ø13.0±0.5 ø21.0±0.8 2.0±0.5 ø180 Dimensions in mm 1.0 ø60 0.5 0.3±0.05 K 8±0.1 1.75±0.1 4±0.1 4±0.1 2±0.1 B A (3.5) Dimensions in mm Sprocket hole 1.55±0.05 Cavity
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20211117 (4/4) inductor_automotive_power_bcl322515rt-d_en.fm INDUCTORS REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using this products. The storage period is within 12 months. Be sure to follow the storage conditions (temperature: 5 to 40°C, humidity: 10 to 75% R H or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Storage conditions after mounting: –55°C to +155°C Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. Do not use products that have received any excessive mechanical shock such as by being dropped. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set therm al design. Do not expose the products to magnets or magnetic fields. The performance of the product may deteriorate if coating materials are used, thus please assess the situation beforehand by ta king this factor into consideration. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products described in this catalog are intended to be installed in automobiles or automotive electronic equipment (AV equip ment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equip- ment, measurement equipment, industrial robots) and to be used in automobiles (including the case where the said automotive product is mounted in a vehicle) or standard applications as general electronic equipment in automotive applications or standard applic ations as general electronic equipment in automotive applications in accordance with the scope and conditions described in this specification, while the said automotive or general electronic equipment including the said product is intended to be used in the usual operat ion and usage methods, respectively. Other than automotive or automotive products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality requires a more stringent level of safety or reliability, or wh ose failure, malfunction or defect could cause serious damage to society, person or property. Please understand that we are not responsible for any damage or liability caused by use of the products in any of the applicati ons below or for any other use exceeding the range or conditions set forth in this specification sheet. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or c onditions set forth in this specification, please contact us. (1) Aerospace/aviation equipment (2) Transportation equipment (electric trains, ships, etc.) (3) Medical equipment (4) Power-generation control equipment (5) Atomic energy-related equipment (6) Seabed equipment (7) Transportation control equipment (8) Public information-processing equipment (9) Military equipment (10) Electric heating apparatus, burning equipment (11) Disaster prevention/crime prevention equipment (12) Safety equipment (13) Other applications that are not considered general-purpose
applications
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securi ng pro- tection circuit/device or providing backup circuits in your equipment. REMINDERS