AFE1203 BURR-BROWN

Document overview

  • PDF pages: 10

Technical content

Page 1

2Mbps, Single Pair HDSL ANALOG FRONT END

FEATURES

G E1/T1 SINGLE PAIR 2B1Q OPERATION G COMPLETE ANALOG INTERFACE G 385mW POWER DISSIPATION G PROGRAMMABLE POWER

DESCRIPTION

Burr-Brown’s Analog Front End greatly reduces the size and cost of a single pair HDSL (High bit rate Digital Subscriber Line) system by providing all of the active analog circuitry needed to connect an HDSL digital signal processor to an external compromise hybrid and an HDSL line transformer. The transmit and receive filter responses automatically change with clock frequency, allowing the AFE1203 to operate over a wide range of data rates. The power dissipation of the device can be reduced under digital control for operation at lower speeds. The AFE1203 will operate at bit rates from 160kbps to 2.3Mbps. It meets ETSI PSD specifications for single pair E1,

as well as ETSI and ANSI PSD specifications for two pair E1 and T1. Functionally, this unit consists of a transmit and a receive section. The transmit section generates, filters, and buffers outgoing 2B1Q data. The receive section filters and digitizes the symbol data received on the telephone line. This IC operates

D/A Converter

PLLOUT PLLIN

Transmit Control

txDAT txCLK

rxSYNC

Receive

rxLOOP

Control 2 rxGAIN

14 Decimation

rxD13 - rxD0

Filter

G 48-LEAD SSOP PACKAGE G SCALEABLE DATA RATE G OPERATION FROM 2.3Mbps TO 160kbps G +5V ONLY (5V OR 3.3V DIGITAL)

G –40°C TO +85°C OPERATION

on a single 5V supply. The digital circuitry in the unit can be connected to a supply from 3.3V to 5V. The chip uses only 385mW for full-speed operation. It is housed in a small 48-lead SSOP package. The receive channel is designed around a fourth-order deltasigma analog-to-digital converter. It includes a difference am- plifier designed to be used with an external compromise hybrid for first-order analog echo cancellation. A programmable gain amplifier with gains 0dB to +9dB is also included. The deltasigma modulator, operating at a 24X oversampling ratio, produces a 14-bit output at symbol rates up to 1168kHz (for 2.3Mbps operation). The transmit channel consists of a digital-to-analog converter and

switched-capacitor pulse forming network followed by a differential line driver. The pulse forming network receives symbol data and generates a standard 2B1Q output waveform. The differential line driver uses a composite output stage combining class B operation (for high efficiency driving large signals) with class AB operation (to minimize crossover distortion).

txLINEP

Pulse

Line

Former

Driver

txLINEN

REFP

Voltage

VCM

Reference

REFN

rxLINEP rxLINEN

Delta-Sigma Modulator

rxHYBP rxHYBN

Patents Pending

International Airport Industrial Park • Mailing Address: PO Box 11400, Tucson, AZ 85734 • Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 • Tel: (520) 746-1111 • Twx: 910-952-1111 Internet: http://www.burr-brown.com/ • FAXLine: (800) 548-6133 (US/Canada Only) • Cable: BBRCORP • Telex: 066-6491 • FAX: (520) 889-1510 • Immediate Product Info: (800) 548-6132

©1998 Burr-Brown Corporation

PDS-1460A

Printed in U.S.A. October, 1998

Page 2

SPECIFICATIONS

Typical at 25°C, AVDD = +5V, DVDD = +3.3V, ftx = 1168kHz (E1 single pair rate) and Normal Power mode, unless otherwise specified.

PDF page 2 diagram

NOTES: (1) With a balanced differential signal, the positive input is 180° out of phase with the negative input, therefore the actual voltage swing about the common mode voltage on each pin is ±1.5V to achieve a differential input range of ±3.0V or 6Vp-p. (2) FSR is Full-Scale Range. (3) The output data is available at twice the symbol rate with interpolated values. (4) With a pseudo-random equiprobable sequence of HDSL pulses; 13.5dBm applied to the transformer (27dBm output from txLINEP and txLINEN). (5) Guaranteed by design and characterization. (6) Uncancelled Echo is a measure of the total analog errors in the transmitter and receiver sections including the effect of non-linearity and noise. See the Discussion of Specifications section of this data sheet for more information. (7) Power dissipation

includes only the power dissipated within the component and does not include power dissipated in the external loads. The AFE1203 is tested with a 1:2 line transformer. (8) This is the settling time required for any gain change, change of rxSYNC or any change of power mode.

Page 3

PIN DESCRIPTIONS

PDF page 3 diagram

The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant any BURR-BROWN product for use in life support devices and/or systems.

Page 4

ABSOLUTE MAXIMUM RATINGS

PIN CONFIGURATION

PDF page 4 diagram
PDF page 4 diagram

PACKAGE/ORDERING INFORMATION

PRODUCT PACKAGE PACKAGE DRAWING NUMBER(1) TEMPERATURE RANGE
AFE1203E 48-Lead SSOP 333 –40°C to +85°C

NOTE: (1) For detailed drawing and dimension table, please see end of data sheet, or Appendix C of Burr-Brown IC Data Book.

ELECTROSTATIC

DISCHARGE SENSITIVITY

This integrated circuit can be damaged by ESD. Burr-Brown

recommends that all integrated circuits be handled with

appropriate precautions. Failure to observe proper handling

and installation procedures can cause damage. ESD damage can range from subtle performance degradation

to complete device failure. Precision integrated circuits may

be more susceptible to damage because very small parametric

changes could cause the device not to meet its published

specifications.

Page 5

TYPICAL PERFORMANCE CURVES

At Output of Pulse Transformer

Typical at 25°C, AVDD = +5V, and DVDD = +3.3V, unless otherwise specified.

AVERAGE POWER SPECTRAL DENSITY LIMIT

PDF page 5 diagram
SPEED LOWER LIMIT BREAK FREQUENCY SLOPE UPPER LIMIT
T1, Two Pair E1, Two Pair E1, Single Pair (E1-SP) –38dBm/Hz –40dBm/Hz –42.5dBm/Hz 196kHz 292kHz 485kHz –80dB/decade –80dB/decade –80dB/decade –118dBm/Hz –120dBm/Hz –122dBm/Hz
PDF page 5 diagram

CURVE 1. Upper Bound of Power Spectral Density Measured at the Transformer Output.

PDF page 5 diagram
LIMITS TWO PAIR T1 AND E1 SINGLE PAIR E1
NORMALIZED LEVELS QUATENARY SYMBOLS (V) NORMALIZED LEVELS QUATENARY SYMBOLS (V)
A B C D E F G H 0.01 1.07 1.00 0.93 0.03 –0.01 –0.16 –0.05 +3 0.0264 2.8248 2.6400 2.4552 0.0792 0.0264 –0.4224 –0.1320 +1 0.0088 0.9416 0.8800 0.8184 0.0264 –0.0088 –0.1408 –0.0440 –1 –0.0088 –0.9416 –0.8800 –0.8184 –0.0264 0.0088 0.1408 0.0440 –3 –0.0264 –2.8248 –2.6400 –2.4552 –0.0792 0.0264 0.4224 0.1320 0.01 1.07 1.00 0.93 0.04 –0.01 –0.20 –0.05 +3 0.0250 2.6750 2.5000 2.3250 0.1000 –0.0250 –0.5000 –1.2500 +1 0.0083 0.8917 0.8333 0.7750 0.0333 –0.0083 –0.1667 –0.0417 –1 –0.0083 –0.8917 –0.8333 –0.7750 –0.0333 0.0083 0.1667 0.0417 –3 0.0250 –2.6750 –2.5000 –2.3250 –0.1000 0.0250 0.5000 0.1250
PDF page 5 diagram

CURVE 2. Transmitted Pulse Template and Actual Performance as Measured at the Transformer Output.

PDF page 5 diagram

CURVE 3. Input Impedance of rxLINE and rxHYB.

Page 6

THEORY OF OPERATION

The transmit channel consists of a D/A converter and a switched-capacitor pulse forming network followed by a differential line driver. The pulse forming network receives symbol data from the DSP and generates a 2B1Q output waveform. The output meets the pulse mask and power spectral density requirements defined in European Telecommunications Standards Institute document RTR/TM-03036 for E1 mode and in sections 6.2.1 and 6.2.2.1 of Bellcore technical advisory TA-NWT-001210 for T1 mode. The differential line driver uses a composite output stage combining class B operation (for high efficiency driving large signals) with class AB operation (to minimize crossover

distortion). The receive channel is designed around a fourth-order delta sigma A/D converter. It includes a difference amplifier designed to be used with an external compromise hybrid for first-order analog crosstalk reduction. A programmable gain amplifier with gains of 0dB to +9dB is also included. The delta sigma modulator operating at a 24X oversampling ratio produces 14 bits of resolution at output rates up to 584kHz. The basic functionality of the AFE1203 is illustrated in Figure 1. The receive channel operates by summing the two differential inputs, one from the line (rxLINE) and the other from the compromise hybrid (rxHYB). The connection of these two

inputs so that the hybrid signal is subtracted from the line signal is described in the paragraph titled “Echo Cancellation in the AFE”. The equivalent gain for each input in the difference amp is 1. The resulting signal then passes to a programmable gain amplifier which can be set for gains of 0dB through 9dB. The ADC converts the signal to a 14-bit digital word, rxD13-rxD0.

SCALEABLE TIMING

The AFE1203 scales operation with the clock frequency. All internal filters, the A/D converter, the D/A converter, and the pulse former change frequency with the clock speed so that the unit can be used at different frequencies by changing the clock speed.

rxLOOP INPUT rxLOOP is the loopback control signal. When enabled, the rxLINEP and rxLINEN inputs are disconnected from the AFE. The rxHYBP and rxHYBN inputs remain connected. Loopback is enabled by applying a positive signal (Logic 1) to rxLOOP.

ECHO CANCELLATION IN THE AFE

The rxHYB input is designed to be subtracted from the rxLINE input for first-order echo cancellation. To accomplish this, note that the rxLINE input is connected to the same polarity signal at the transformer (positive to positive and negative to negative) while the rxHYB input is connected to opposite polarity through the compromise hybrid (negative to positive and positive to negative) as shown in Figure 2.

RECEIVE DATA CODING

The data from the receive channel A/D converter is coded in Straight Offset Binary.

PDF page 6 diagram

RECEIVE CHANNEL PROGRAMMABLE

GAIN AMPLIFIER

The gain of the amplifier at the input of the Receive Channel is set by two gain control pins, rxGAIN1 and rxGAIN0. The resulting gain between 0dB and +9dB is shown below.

PDF page 6 diagram
PDF page 6 diagram

FIGURE 1. Functional Block Diagram of AFE1203.

Page 7

PDF page 7 diagram

FIGURE 2. Basic Connection Diagram.

rxHYB AND rxLINE INPUT ANTI-ALIASING FILTERS The –3dB frequency of the input anti-aliasing filter for the rxLINE and rxHYB differential inputs should be approximately 2MHz for operation at 2.3Mbps. Suggested values for the filter are 375Ω for each of the two input resistors and 100pF for the capacitor. Together the two 375Ω resistors and the 100pF capacitor result in –3dB frequency of just over 2MHz. The 375Ω input resistors will result in a minimal voltage divider loss with the input impedance of the AFE1203. This circuit applies at rates of 1Mbps to 2Mbps. For slower rates, the anti-aliasing filters will give best performance with their –3dB frequency approximately equal to the bit rate. For

example, a –3dB frequency of 500kHz should be used for a single pair bit rate of 500kbps.

rxHYB AND rxLINE INPUT BIAS VOLTAGE The transmitter output on the txLINE pins and the rxLINE inputs are centered at midscale, 2.5V. Inside the AFE1203, the rxHYB and rxLINE signals are subtracted as described in the paragraph on echo cancellation above. This means that the rxHYB inputs need to be centered at 2.5V just as the rxLINE signal is centered at 2.5V. The external compromise hybrid must be designed so that the signal into the rxHYB inputs remains centered at 2.5V.

Page 8

TIMING DIAGRAM

PDF page 8 diagram

FIGURE 3. Timing Diagram.

RECEIVE TIMING

The rxSYNC signal controls portions of the A/D converter’s decimation filter and the data output timing of the A/D converter. It is generated at the symbol rate by the user and must be synchronized with txCLK. The leading edge of rxSYNC can occur at the leading edge of txCLK or it can be shifted by the user in increments of 1/16 of a symbol period to one of 15 discrete delay times after the leading edge of txCLK.

RECEIVE OUTPUT DATA RATE

The receive channel delta-sigma A/D converter of the AFE1203 uses a modulator which operates at an oversampling

rate of 24X the symbol rate. The A/D converter’s decimation filter downsamples the modulator output by a factor of 12. The bandwidth of the decimation filter is equal to one-half the symbol rate. This yields two output words per symbol period. These two output words are shown as Data 1 and Data 1a in Figure 3. The specifications of the AFE1203 assume that one A/D converter output is used per symbol period and the other output is ignored. The Receive Timing diagram above suggests using the rising edge of the rxSYNC pulse to read the first data output in a symbol period. Either data output may be used. Both data outputs may be used for more flexible post-processing.

Page 9

DISCUSSION OF

SPECIFICATIONS

UNCANCELLED ECHO

The key measure of transceiver performance is uncancelled echo. This measurement is made as shown in the diagram of Figure 4. The AFE is connected to an output circuit including a typical 1:2 line transformer. The line is simulated by a 135Ω resistor. Symbol sequences are generated by the tester and applied both to the AFE and to the input of an adaptive filter. The output of the adaptive filter is subtracted from the AFE output to form the uncancelled echo signal. Once the filter taps have converged, the rms value of the uncancelled echo is calculated. Since there is no far-end signal source or additive line noise, the uncancelled echo contains only noise

and linearity errors generated in the transmitter and receiver. The data sheet value for uncancelled echo is the ratio of the rms uncancelled echo (referred to the receiver input through the receiver gain) to the nominal transmitted signal (13.5dBm into 135Ω, or 1.74Vrms). This echo value is measured under a variety of conditions: with loopback enabled (line input disconnected); with loopback disabled under all receiver gain ranges; and with the line shorted (S1 closed in Figure 4).

PROGRAMMABLE POWER DISSIPATION

The power dissipation of the AFE1203 is digitally programmable by the user to three levels: Normal, Medium, and Low. The maximum bit rate of the AFE1203 is 2.3Mbps with Normal power dissipation. At lower power dissipation

levels, the maximum bit rate is lower and in addition, the minimum bit rate is lower. The power control pin (pin 22) has three input levels, Logic 1, Logic 0, and high impedance. In the high impedance state, up to 20µA leakage current can be tolerated out of the power control pin. The AFE1203 requires six baud periods to settle after a change in the power control pin status. Typical power dissipation specifications, shown in Table I, assume a 5V analog supply, a 3.3V digital supply, standard 13.5dBm delivered to the line, a pseudo random equiprobable sequence of HDSL output pulses, and a 1:2 turns ratio line transformer. The power dissipation specifications in-

cludes all power dissipated in the AFE1203—it does not include power dissipated in the external load. The external power is 16.5dBm, 13.5dBm to the line and 13.5dBm to the impedance matching resistors. The external power of 16.5dBm is 45mW. If a 5V digital supply is used rather than a 3.3V supply, the power dissipation increases by approximately 3mW.

PDF page 9 diagram

POWER

LEVEL

Normal Medium Low

TABLE I. Power Control Operation.

PDF page 9 diagram

FIGURE 4. Uncancelled Echo Test Diagram.

Page 10

LAYOUT

The analog front end of an HDSL system has a number of conflicting requirements. It must accept and deliver digital outputs at fairly high rates of speed, phase-lock to a highspeed digital clock, and convert the line input to a highprecision (14-bit) digital output. Thus, there are really three sections of the AFE1203: the digital section, the phaselocked loop, and the analog section. A combined analog and digital ground plane is recommended. The ground plane should pass under all of the AFE1203 and its pins. The power supply for the digital section of the AFE1203 can range from 3.3V to 5V. This supply should be decoupled to ground with a ceramic 0.1µF capacitor placed as close to

DGND (pin 12) and DVDD (pin 13) as possible. Ideally, both a digital power supply plane and a ground plane should run up to and underneath the digital pins of the AFE1203 (pins 3 through 26). However, DVDD may be supplied by a wide printed circuit board (PCB) trace. A ground plane underneath all digital pins is strongly recommended. The Phase Locked Loop (PLL) analog supply, pin 2, must be derived from AVDD, the general analog supply. The power supply to the PLL must be in the range of 4.75V to 5.25V. The PLL section of the AFE1203 should be decoupled with

both a 10µF tantalum capacitor and a 0.1µF ceramic capacitor. Both capacitors should be placed between pins 1 and 2. The ceramic capacitor should be placed as close to the AFE1203 as possible. The placement of the tantalum capacitor is not as critical, but should be close. A 5Ω to 10Ω resistor should be used to connect the PLL supply (pin 2) to the analog supply. This resistor, in combination with the 10µF tantalum capacitor, form a low pass filter to keep glitches that occur on the general analog supply, AVDD, from affecting the PLL supply. The PLL ground (pin 1) should connect directly to the ground plane. The ground plane should also extend underneath PLLOUT and PLLIN

(pins 47 and 48, respectively). The remaining portion of the AFE1203 should be considered analog. All AGND pins should be connected directly to the common ground plane and all AVDD pins should be connected to an analog 5V power plane. Both of these planes should have a low impedance path to the power supply. Ideally, all ground planes and traces and all power planes and traces should return to the power supply connector before being connected together (if necessary). Each ground and power trace pair should be routed over each other, should not overlap any portion of another pair, and the pairs should be separated by a distance of at least 0.25 inch (6mm).