AFE1115 BURR-BROWN

Document overview

  • PDF pages: 12

Technical content

Page 1

PDF page 1 diagram

Page 2

SPECIFICATIONS

Typical at 25°C, AVDD = +5V, DVDD = +3.3V, ftx = 584kHz (E1 rate), unless otherwise specified.

PDF page 2 diagram

NOTES: (1) With a balanced differential signal, the positive input is 180° out of phase with the negative input, therefore the actual voltage swing about the commonmode voltage on each pin is ±1.5V to achieve a total input range of ±3.0V or 6Vp-p. (2) FSR is Full-Scale Range. (3) The output data is available at twice the symbol rate with interpolated values. (4) With a pseudo-random equiprobable sequence of HDSL pulses; 13.5dBm applied to the transformer (16.5dBm output from txLINEP and txLINEN). (5) See the Test Method section of this data sheet for more information. (6) Guaranteed by design and characterization. (7) Uncancelled Echo is a measure of the total analog errors in the transmitter and receiver sections including the effect of non-linearity and noise. See the Discussion of Specifications sections

of this data sheet for more information. (8) Power dissipation includes only the power dissipated with in the component and does not include power dissipated in the external loads. See the Discussion of Specifications section for more information.

Page 3

PIN CONFIGURATION

PACKAGE/ORDERING INFORMATION

PDF page 3 diagram
PRODUCT PACKAGE PACKAGE DRAWING NUMBER(1) TEMPERATURE RANGE
AFE1115E 56-Pin Plastic SSOP 346 –40°C to +85°C

NOTE: (1) For detailed drawing and dimension table, please see end of data sheet, or Appendix C of Burr-Brown IC Data Book.

ELECTROSTATIC

DISCHARGE SENSITIVITY

This integrated circuit can be damaged by ESD. Burr-Brown recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.

Page 4

PIN DESCRIPTIONS

PDF page 4 diagram

The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant any BURR-BROWN product for use in life support devices and/or systems.

Page 5

TYPICAL PERFORMANCE CURVES

At Output of Pulse Transformer

The curves shown below are measured at the line output of the HDSL transformer. Typical at 25°C, AVDD = +5V, DVDD = +3.3V, unless otherwise specified.

PDF page 5 diagram

CURVE 1. Upper Bound of Power Spectral Density Measured at Output of HDSL Transformer.

0.4T 0.4T

B = 1.07

PDF page 5 diagram
PDF page 5 diagram
NORMALIZED LEVEL QUATERNARY SYMBOLS
+3 +1 –1 –3
A B C D L K E F G H 0.01 1.07 1.0D0 O 0.93 NOWN 0.03 –0.01 –0.16 –0.05 0.0264 2.8248 N2'.T64 0D0 E 2.4552 IF TE 0.0792 –0.0264 –0.4224 –0.1320 0.0088 0.9416 L0E.88T00E 0.8184 EPLE 0.0264 –0.0088 –0.1408 –0.0440 –0.0088 –0.9416 T–A0.8B80L0 –0.8184 IS LEA –0.0264 0.0088 0.1408 0.0440 –0.0264 –2.8248 E –2.6400 –2.4552 VING –0.0792 0.0264 0.4224 0.1320
PDF page 5 diagram

CURVE 2. Transmitted Pulse Template and Actual Performance as Measured at Transformer Output.

PDF page 5 diagram

CURVE 3. Input Impedance of rxLINE and rxHYB.

Page 6

THEORY OF OPERATION

The transmit channel consists of a switched-capacitor pulse forming network followed by a differential line driver. The pulse forming network receives symbol data through a serial interface and generates a standard 2B1Q output waveform. The output meets the pulse mask and power spectral density requirements defined in European Telecommunications Standards Institute document RTR/TM-03036 for E1 mode and in sections 6.2.1 and 6.2.2.1 of Bellcore technical advisory TA-NWT-001210 for T1 mode. The differential line driver uses a composite output stage combining class B operation (for high efficiency driving large signals) with class AB operation (to minimize crossover distortion).

The receive channel is designed around a fourth-order delta sigma A/D converter. It includes a difference amplifier designed to be used with an external compromise hybrid for first order analog echo cancellation. A programmable gain amplifier with gains of –3dB to +9dB is also included. The delta sigma modulator operating at a 24X oversampling ratio produces a parallel 14-bit output at symbol rates up to 584kHz. The basic functionality of the AFE1115 is illustrated in Figure 1 shown below. The receive channel operates by summing the two differential inputs, one from the line (rxLINE) and the other from the compromise hybrid (rxHYB). These two inputs are con-

nected so that the hybrid signal is subtracted from the line signal. This connection is described in the paragraph titled “Echo Cancellation in the AFE”. The equivalent gain for each input in the difference amp is one. The resulting signal then passes to a programmable gain amplifier which can be set for gains of –3dB through +9dB. The ADC converts the signal to a 14-bit digital word, rxD13-rxD0. An independent VCXO control DAC and VCXO circuitry is also included on the chip. This VCXO is designed to be used

in remote units for clock recovery. The VCXO is formed with the on-board circuitry plus external crystal and varactor diodes. The VCXO control DAC receives control data through a serial interface which sets a voltage level at the output of the DAC. The DAC output controls the frequency of the VCXO. To achieve specified analog performance when using the VCXO, the crystal frequency of the VCXO must be 48x the baud rate.

rxLOOP INPUT rxLOOP is the loopback control signal. When enabled, the rxLINE+ and rxLINE– inputs are disconnected from the AFE. The rxHYB+ and rxHYB– inputs remain connected. Loopback is enabled by applying a positive signal (Logic 1) to rxLOOP.

ECHO CANCELLATION IN THE AFE

The rxHYB input is designed to be subtracted from the rxLINE input for first order echo cancellation. To accomplish this, note that the rxLINE input is connected to the same polarity signal at the transformer (positive to positive and negative to negative) while the rxHYB input is connected to opposite polarity through the compromise hybrid (negative to positive and positive to negative) as shown in Figure 2.

RECEIVE DATA CODING

The data from the receive channel A/D converter is coded in two’s complement.

PDF page 6 diagram
PDF page 6 diagram

FIGURE 1. Functional Block Diagram of AFE1115 Circuit.

Page 7

PDF page 7 diagram

FIGURE 2. Basic Connection Diagram.

RECEIVE CHANNEL PROGRAMMABLE

GAIN AMPLIFIER

The gain of the amplifier at the input of the Receive Channel is set by two gain control pins, rxGAIN1 and rxGAIN0. The resulting gain between –3dB and +9dB is shown below.

PDF page 7 diagram

SCALEABLE DATA RATE

The AFE1115 scales operation with the clock frequency. All internal filters and the pulse former change frequency with the clock speed so that the unit can be used at different frequencies just by changing the clock speed.

rxHYBAND rxLINE INPUT ANTI-ALIASING FILTERS An external input anti-aliasing filter is needed on the hybrid and line inputs as shown in the Basic Connection Diagram above. The –3dB frequency of the input anti-aliasing filter for the rxLINE and rxHYB differential inputs should be approximately 1MHz for E1 and T1 symbol rates. Suggested values for the filter are 750Ω for each of the two input resistors and 100pF for the capacitor. Together the two 750Ω resistors and the 100pF capacitor result in a 3dB frequency of just over 1MHz. The 750Ω input resistors will result in a minimal voltage divider loss with the input impedance of the AFE1115. For speed less than E1, the anti-aliasing filters will give best

performance with 3dB frequency approximately equal to two times the symbol rate. For instance, a 3dB frequency of 400kHz may be used for a single line symbol rate of 196k symbols per second.

Page 8

PDF page 8 diagram

rxHYB AND rxLINE INPUT COMMON-MODE

OPTIONAL VOLTAGE The AFE1115 will meet specifications with the application

circuit shown in the Basic Connection Diagram (Figure 2)

above. However, slightly improved performance may be

obtained with the Hybrid input (rxHYB) and the Line input

(rxLINE) set to a common mode voltage of 1.5V. The

negative reference output pin (vrREFN, pin 40) provides a

good 1.5V level to use to set the common-mode voltage.

The circuit shown in Figure 3 can be used to set the

common-mode voltage of the Line input to 1.5V. A similar circuit can be used to set the Hybrid input to 1.5V.

Another option for the Hybrid input is to design the external

compromise hybrid so that the signal into the rsHYB inputs

is centered at 1.5V. If the compromise hybrid circuit is AC

FIGURE 3. Optional rxLINE Input Common-mode Voltage

coupled to the rxHYB inputs, an external pull-up resistor to

Control.

vrREFN may be needed to center the input at 1.5V.

PDF page 8 diagram
PDF page 8 diagram

FIGURE 4. Timing Diagram.

Page 9

TRANSMIT SYMBOL DATA During each symbol period transmit symbol data are sent to

the AFE1115 in serial format through the txDATA input pin.

A 16 bit word is sent to the AFE1115 to determine the

symbol that is transmitted by the AFE1115. The symbol data

is contained in the first three bits of the data, the remaining

13 bits of the 16 bit word are ignored. The most significant bit (MSB) is the transmit enable bit.

When the MSB is a logic 0, a zero symbol only is transmit-

ted regardless of the state of the other two bits. When the

MSB is a logic 1, bits 2 and 3 determine the symbol

transmitted as shown in the table below.

PDF page 9 diagram

TABLE I. Transmit Symbol Data (txDATA). X = Don’t Care.

VCXO CONTROL D/A CONVERTER DATA During each symbol period VCXO control D/A converter

data is sent to the AFE1115 in serial format through the

vcDATA input pin. A 16 bit word is sent to the AFE1115 to

determine the output of the VCXO control D/A converter.

The VCXO control D/A converter is connected to the

VCXO circuit to control the VCXO frequency. The D/A

converter input is contained in the first eight bits of the data,

the remaining eight bits of the 16 bit word are ignored.

INPUT CODE (vcDATA) MSB ANALOG OUTPUT
01111111XXXXXXXX 00000000XXXXXXXX 10000000XXXXXXXX Negative Full Scale (+0.5V) Mid Scale (+2.5V) Positive Full Scale (+4.5V)

TABLE II. VCXO Control DAC Output. X = Don’t Care.

PDF page 9 diagram

FIGURE 5. Receive Timing Diagram.

PARAMETER DESCRIPTION MIN TYP MAX VALUE
t 10 t11 t 12 t13 t 14 t 15 t16 rxSYNC Pulse Width Delay of rxSYNC from rising edge of txCLK, n = 0 to 47 Nominal Time at Which rxDATA Changes from Data 1 to Data 1a Nominal Time at Which rxDATA Changes from Data 1a to Data 2 Uncertainty of t12 and t13 txCLK Pulse Width Symbol Period, T T/24 nT/48 – T/96 T/16 1.7 (n + 1.5) T/48 (n + 25.5) T/48 nT/48 + T/96 20 15T/16 10.2 ns µs

TABLE III. Receive Timing (n = Delay Increments from txCLK).

Page 10

RECEIVE TIMING

The rxSYNC signal controls portions of the A/D converter’s decimation filter and the data output timing of the A/D converter. It is generated at the symbol rate by the user and must be synchronized with txCLK. The leading edge of rxSYNC can occur at the leading edge of txCLK or it can be shifted by the user in increments of 1/48 of a symbol period to one of 47 discrete delay times after the leading edge of txCLK. The bandwidth of the A/D converter decimation filter is equal to one half of the symbol rate. The A/D converter data output rate is 2X the symbol rate. The specifications of the AFE1115 assume that one A/D converter output is used per symbol period and the other output is ignored. The Receive

Timing Diagram above suggests using the rxSYNC pulse to read the first data output in a symbol period. Either data output may be used. Both data outputs may be used for more flexible post-processing.

DISCUSSION OF

SPECIFICATIONS

UNCANCELLED ECHO

The key measure of transceiver performance is uncancelled echo. This measurement is made as shown in the diagram of Figure 6 and the measurement is made as follows. The AFE is connected to an output circuit including a typical 1:2.3 line transformer. The line is simulated by a 135Ω resistor.

Symbol sequences are generated by the tester and applied both to the AFE and to the input of an adaptive filter. The output of the adaptive filter is subtracted from the AFE output to form the uncancelled echo signal. Once the filter taps have converged, the RMS value of the uncancelled echo is calculated. Since there is no far-end signal source or additive line noise, the uncancelled echo contains only noise and linearity errors generated in the transmitter and receiver. The data sheet value for uncancelled echo is the ratio of the RMS uncancelled echo (referred to the receiver input through the receiver gain) to the nominal transmitted signal (13.5dBm

into 135Ω, or 1.74Vrms). This echo value is measured under a variety of conditions: with loopback enabled (line input disabled); with loopback disabled under all receiver gain ranges; and with the line shorted (S1 closed in Figure 6).

POWER DISSIPATION

Approximately 75% of the power dissipation in the AFE1115 is in the analog circuitry, and this component does not change with clock frequency. However, the power dissipation in the digital circuitry does decrease with lower clock frequency. In addition, the power dissipation in the digital section is decreased with operation from a smaller supply voltage, such as 3.3V. (The analog supply, must remain in the range 4.75V to 5.25V.) The power dissipation listed in the specifications section applies under these normal operating conditions: 5V Analog Power Supply; 3.3V Digital Power Supply; E1 baud rate;

PDF page 10 diagram

FIGURE 6. Uncancelled Echo Test Diagram.

Page 11

13.5dBm delivered to the line; and a pseudo-random equiprobable sequence of HDSL pulses. The power dissipation specifications includes all power dissipated in the AFE1115, it does not include power dissipated in the external

load.

The external power is 16.5dBm, 13.5dBm to the line and 13.5dBm to the impedance matching resistors. The external load power of 16.5dBm is 45mW. The typical power dissipation in the AFE1115 under various conditions is shown in

PDF page 11 diagram

TABLE IV. Typical Power Dissipation.

Table IV.

LAYOUT

The analog front end of an HDSL system has a number of conflicting requirements. It must accept and deliver digital outputs at fairly high rates of speed, generate a VCXO clock, phase-lock to a high-speed digital clock, and convert the line input to a high-precision (14-bit) digital output. Thus, there are really four sections of the AFE1115: the digital section, the phase-locked loop, the VCXO and the analog section.

DIGITAL LAYOUT

The power supply for the digital section of the AFE1115 can range from 3.3V to 5V. This supply should be decoupled to digital ground with a ceramic 0.1µF capacitor placed as close as possible to digital ground (DGND, pin 16) and digital power (DVDD, pin 17). Ideally, both a digital power supply plane and a digital ground plane should run to and underneath the digital pins of the AFE1115 (pins 7 through 30). However, DVDD may be supplied by a wide printed circuit board trance. A digital ground plane underneath all digital pins is strongly recommended. The VCXO circuit needs special attention for layout. There is a portion of the external VCXO circuitry which needs to be as far away as

possible from a ground or power plane or other traces. See the discussion below in the section titled VCXO Circuit and Layout.

ANALOG LAYOUT

The phase-locked loop is powered from AVDD (pin 50) and its ground is referenced to AGND (pin 49). Note that AVDD must be in the 4.75V to 5.25V range. This portion of the AFE1115 should be decoupled with both 10µF Tantalum capacitor and a 0.1µF ceramic capacitor. The ceramic ca- pacitor should be placed as close to the AFE1115 as pos-

sible. The placement of the Tantalum capacitor is not as critical, but should be close to the pin. In each case, the capacitor should be connected between AVDD and AGND (pins 49 and 50). The capacitors should be placed in quiet analog areas rather than noisy digital areas. In most systems, it will be natural to derive AVDD for the phase-locked loop (PLL) from the AVDD supply. A 5Ω to 10Ω resistor should be used to connect PLL AVDD (pin 49) to the analog supply. This resistor in combination with the 10µF capacitor form a lowpass filter—keeping glitches on the analog supply from affecting the phase locked loop. Ideally, the phase-locked loop power supply would originate

from the analog supply (via the 5Ω to 10Ω resistor) near the power connector for the printed circuit board. Likewise, the PLL ground should connect to a large PCB trace or small ground plane which returns to the power supply connector underneath the PLL AVDD supply path. The PLL “ground plane” should also extend underneath PLLIN and PLLOUT (pins 51 and 52). The remaining portion of the AFE1115 should be considered analog. The four non-PLL AGND pins (pins 36, 37, 42, and 46) should be connected directly to a common analog ground plane and all non-PLL AVDD pins should be connected to an analog 5V power plane. Both of these planes should have a low impedance path to the power supply.

Ideally, all ground planes and traces and all power planes and traces should return to the power supply connector before being connected together (if necessary). Each ground and power pair should be routed over each other, should not overlap any portion of another pair, and the pairs should be separated by a distance of at least 0.25 inch (6mm). One exception is that the digital and analog ground planes should be connected together underneath the AFE1115 by a small trace.

VCXO CIRCUIT AND LAYOUT

The VCXO circuitry is shown in Figure 7. The basic VCXO circuit consists of on-chip control DAC, amplifiers, Schmidt triggers, and clock buffer along with an external crystal and varactor diodes. The control DAC output (vcDAC) varies the capacitance of the varactor diodes (D1 and D2), which controls the frequency at which the crystal circuit oscillates. The buffered clock output is available at pin 3, VCXO Clock Output. Important Note: To achieve specified analog performance when using VCXO, the crystal frequency of the VCXO must be 48x the baud rate. In addition, the txCLK and the rxSYNC control signals must be derived from the VCXO clock so that the edges of the control signal are synchronized

with the 48x crystal frequency. If these recommendations are followed, the key internal analog decisions are made at the time of minimum noise. As an example, for an E1 rate of 1168kbps, the symbol rate is 584k symbols per second. In this case the VCXO crystal frequency should be 48 x 584k = 28.032MHz. Likewise, for T1, the crystal frequency should be 18.816MHz.

Page 12

The performance of the VCXO is critically dependent on the

external components and printed circuit board layout that is

used. The varactor diodes and the crystal are particularly

important components. The printed circuit board layout containing the two varactor

diodes, D1 and D2, in the VCXO external circuitry is critical

to the performance of the VCXO. In particular, the two

connection points of the varactor diodes shown in the Figure

7 must have very low parasitic capacitance to ground to

achieve the best tuning range possible. To achieve lowest

parasitic capacitance to ground, there must be no ground

plane or other PCB traces near these two points. Ground

planes and other traces should be kept 1 cm away from these

two points where possible.

Figure 8 shows an example of a printed circuit board layout

of the sensitive VCXO circuitry for the circuit shown in

Figure 7. There should be no ground planes, power planes or

other traces in the white area indicated around the two

sensitive points. The balance of the circuit board should be

covered by ground planes where possible. With the circuit

shown in Figure 7, these typical specifications were achieved.

Pull Range at 20MHz ±125ppm
Frequency Range of Crystal that can be used 10MHz to 28MHz
Crystal Frequency 48x baud rate
PDF page 12 diagram

FIGURE 7. VCXO Circuitry.

PDF page 12 diagram

FIGURE 8. VCXO Circuit Layout, Approximately Two Times Actual Size.