AFE1103 BURR-BROWN
Document overview
- PDF pages: 10
Technical content
Page 1
HDSL/MDSL ANALOG FRONT END
FEATURES
G COMPLETE ANALOG INTERFACE G T1, E1, AND MDSL OPERATION G CLOCK SCALEABLE SPEED G SINGLE CHIP SOLUTION G +5V ONLY (5V OR 3.3V DIGITAL) G 250mW POWER DISSIPATION G 48-PIN SSOP G –40°C TO +85°C OPERATION G SECOND SOURCED BY BROOKTREE Bt8921
Pulse Former
PLLOUT PLLIN
Transmit
txDATP
Control
txDATN txCLK
rxSYNC
Receive
rxLOOP
Control
2 rxGAIN
14 Decimation
rxD13 - rxD0
Filter
DESCRIPTION
Burr-Brown’s Analog Front End greatly reduces the size and cost of an HDSL or MDSL system by providing all of the active analog circuitry needed to connect the Brooktree Bt8952 HDSL digital signal processor to an external compromise hybrid and a 1:2 HDSL line transformer. All internal filter responses as well as the pulse former output scale with clock frequency— allowing the AFE1103 to operate over a range of bit rates from 196kbps to 1.168Mbps. Functionally, this unit is separated into a transmit and a receive section. The transmit section generates, filters, and buffers outgoing 2B1Q data. The receive section filters and digitizes the symbol data received
on the telephone line and passes it to the Bt8952. The HDSL Analog Interface is a monolithic device fabricated on 0.6µCMOS. It operates on a single +5V supply. It is housed in a 48-pin SSOP package. This unit is second sourced by Brooktree’s Bt8921.
txLINEP
Line Driver
txLINEN
REFP
Voltage
VCM
Reference
REFN
rxLINEP rxLINEN
Delta-Sigma Modulator
rxHYBP rxHYBN
Patents Pending
International Airport Industrial Park • Mailing Address: PO Box 11400, Tucson, AZ 85734 • Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 • Tel: (520) 746-1111 • Twx: 910-952-1111 Internet: http://www.burr-brown.com/ • FAXLine: (800) 548-6133 (US/Canada Only) • Cable: BBRCORP • Telex: 066-6491 • FAX: (520) 889-1510 • Immediate Product Info: (800) 548-6132
©1996 Burr-Brown Corporation
PDS-1330A
Printed in U.S.A. August, 1996
Page 2
SPECIFICATIONS
Typical at 25°C, AVDD = +5V, DVDD = +3.3V, ftx = 584kHz (E1 rate), unless otherwise specified.

NOTES: (1) With a balanced differential signal, the positive input is 180° out of phase with the negative input, therefore the actual voltage swing about the common mode voltage on each pin is ±1.5V to achieve a differential input range of ±3.0V or 6Vp-p. (2) FSR is Full-Scale Range. (3) The output data is available at twice the symbol rate with interpolated values. (4) With a pseudo-random equiprobable sequence of HDSL pulses; 13.5dBm applied to the transformer (27dBm output from txLINEP and txLINEN). (5) See the Discussion of Specifications section of this data sheet for more information. (6) Guaranteed by design and characterization. (7) Uncancelled Echo is a measure of the total analog errors in the transmitter and receiver sections including the effect of non-linearity and noise. See the Discussion
of Specifications section of this data sheet for more information. (8) Power dissipation includes only the power dissipated within the component and does not include power dissipated in the external loads. See the Discussion of Specifications section for more information.
Page 3
PIN DESCRIPTIONS

The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant any BURR-BROWN product for use in life support devices and/or systems.
Page 4
PIN CONFIGURATION
ABSOLUTE MAXIMUM RATINGS


PACKAGE/ORDERING INFORMATION
| PRODUCT | PACKAGE | PACKAGE DRAWING NUMBER(1) | TEMPERATURE RANGE |
| AFE1103E | 48-Pin Plastic SSOP | 333 | –40°C to +85°C |
NOTE: (1) For detailed drawing and dimension table, please see end of data sheet, or Appendix C of Burr-Brown IC Data Book.
ELECTROSTATIC
DISCHARGE SENSITIVITY
This integrated circuit can be damaged by ESD. Burr-Brown
recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling
and installation procedures can cause damage. ESD damage can range from subtle performance degradation
to complete device failure. Precision integrated circuits may
be more susceptible to damage because very small parametric
changes could cause the device not to meet its published
specifications.
Page 5
TYPICAL PERFORMANCE CURVES
At Output of Pulse Transformer
Typical at 25°C, AVDD = +5V, DVDD = +3.3V, unless otherwise specified.

CURVE 1. Upper Bound of Power Spectral Density Measured at the Transformer Output.
0.4T 0.4T
B = 1.07


| NORMALIZED LEVEL | QUATERNARY SYMBOLS | ||||
|---|---|---|---|---|---|
| +3 | +1 | –1 | –3 | ||
| A B C D E F G H | 0.01 1.07 1.00 0.93 0.03 –0.01 –0.16 –0.05 | 0.0264 2.8248 2.6400 2.4552 0.0792 –0.0264 –0.4224 –0.1320 | 0.0088 0.9416 0.8800 0.8184 0.0264 –0.008 –0.140 –0.044 | –0.0088 –0.9416 –0.8800 –0.8184 –0.0264 8 0.0088 8 0.1408 0 0.0440 | –0.0264 –2.8248 –2.6400 –2.4552 –0.0792 0.0264 0.4224 0.1320 |

CURVE 2. Transmitted Pulse Template and Actual Performance as Measured at the Transformer Output.

CURVE 3. Input Impedance of rxLINE and rxHYB.
Page 6
THEORY OF OPERATION
The transmit channel consists of a switched-capacitor pulse forming network followed by a differential line driver. The pulse forming network receives symbol data from the XMIT and XMITB outputs of the Bt8952 and generates a 2B1Q output waveform. The output meets the pulse mask and power spectral density requirements defined in European Telecommunications Standards Institute document RTR/ TM-03036 for E1 mode and in sections 6.2.1 and 6.2.2.1 of Bellcore technical advisory TA-NWT-001210 for T1 mode. The differential line driver uses a composite output stage combining class B operation (for high efficiency driving large signals) with class AB operation (to minimize cross-
over distortion). The receive channel is designed around a fourth-order delta sigma A/D converter. It includes a difference amplifier designed to be used with an external compromise hybrid for first order analog crosstalk reduction. A programmable gain amplifier with gains of 0dB to +9dB is also included. The delta sigma modulator operating at a 24X oversampling ratio produces 14 bits of resolution at output rates up to 584kHz. The basic functionality of the AFE1103 is illustrated in Figure 1 shown below. The receive channel operates by summing the two differential inputs, one from the line (rxLINE) and the other from the compromise hybrid (rxHYB). The connection of these two
inputs so that the hybrid signal is subtracted from the line signal is described in the paragraph titled “Echo Cancellation in the AFE”. The equivalent gain for each input in the difference amp is 1. The resulting signal then passes to a programmable gain amplifier which can be set for gains of 0dB through 9dB. The ADC converts the signal to a 14-bit digital word, rxD13-rxD0.
rxLOOP INPUT rxLOOP is the loopback control signal. When enabled, the rxLINEP and rxLINEN inputs are disconnected from the AFE. The rxHYBP and rxHYBN inputs remain connected. Loopback is enabled by applying a positive signal (Logic 1) to rxLOOP.
ECHO CANCELLATION IN THE AFE
The rxHYB input is designed to be subtracted from the rxLINE input for first order echo cancellation. To accomplish this, note that the rxLINE input is connected to the same polarity signal at the transformer (positive to positive and negative to negative) while the rxHYB input is connected to opposite polarity through the compromise hybrid (negative to positive and positive to negative) as shown in Figure 2.
RECEIVE DATA CODING
The data from the receive channel A/D converter is coded in offset binary.

RECEIVE CHANNEL PROGRAMMABLE
GAIN AMPLIFIER
The gain of the amplifier at the input of the Receive Channel is set by two gain control pins, rxGAIN1 and rxGAIN0. The resulting gain between 0dB and +9dB is shown below.


FIGURE 1. Functional Block Diagram of AFE1103.
Page 7

FIGURE 2. Basic Connection Diagram.
rxHYB AND rxLINE INPUT ANTI-ALIASING FILTERS The –3dB frequency of the input anti-aliasing filter for the rxLINE and rxHYB differential inputs should be about 1MHz. Suggested values for the filter are 750Ω for each of the two input resistors and 100pF for the capacitor. Together the two 750Ω resistors and the 100pF capacitor result in –3dB frequency of just over 1MHz. The 750Ω input resistors will result in a minimal voltage divider loss with the input impedance of the AFE1103. This circuit applies at both T1 and E1 rates. For slower rates, the antialiasing filters will give best performance with their –3dB frequency approximately equal to the bit rate. For
example, a –3dB frequency of 500kHz should be used for a single pair bit rate of 500kbps.
rxHYB AND rxLINE INPUT BIAS VOLTAGE The transmitter output on the txLINE pins is centered at midscale, 2.5V. But, the rxLINE input signal is centered at 1.5V in the circuit shown in Figure 2 above. Inside the AFE1103, the rxHYB and rxLINE signals are subtracted as described in the paragraph on echo cancellation above. This means that the rxHYB inputs need to be centered at 1.5V just as the rxLINE signal is centered at 1.5V. REFN (Pin 36) is a 1.5V voltage source. The external compromise hybrid must be designed so that the signal into the rxHYB inputs is centered at 1.5V.
Page 8
TIMING DIAGRAM

FIGURE 3. Timing Diagram.
RECEIVE TIMING
The rxSYNC signal controls portions of the A/D converter’s decimation filter and the data output timing of the A/D converter. It is generated at the symbol rate by the user and must be synchronized with txCLK. The leading edge of rxSYNC can occur at the leading edge of txCLK or it can be shifted by the user in increments of 1/16 of a symbol period to one of 15 discrete delay times after the leading edge of txCLK.
The bandwidth of the A/D converter decimation filter is equal to one half of the symbol rate. The A/D converter data output rate is 2X the symbol rate. The specifications of the AFE1103 assume that one A/D converter output is used per symbol period and the other interpolated output is ignored. The Receive Timing Diagram above suggests using the rxSYNC pulse to read the first data output in a symbol period. Either data output may be used. Both data outputs may be used for more flexible post-processing.
Page 9
DISCUSSION OF
SPECIFICATIONS
UNCANCELLED ECHO
The key measure of transceiver performance is uncancelled echo. This measurement is made as shown in the diagram of Figure 4. The AFE is connected to an output circuit including a typical 1:2 line transformer. The line is simulated by a 135Ω resistor. Symbol sequences are generated by the tester and applied both to the AFE and to the input of an adaptive filter. The output of the adaptive filter is subtracted from the AFE output to form the uncancelled echo signal. Once the filter taps have converged, the RMS value of the uncancelled echo is calculated. Since there is no far-end signal source or additive line noise, the uncancelled echo contains only noise
and linearity errors generated in the transmitter and receiver. The data sheet value for uncancelled echo is the ratio of the RMS uncancelled echo (referred to the receiver input through the receiver gain) to the nominal transmitted signal (13.5dBm into 135Ω, or 1.74Vrms). This echo value is measured under a variety of conditions: with loopback enabled (line input disconnected); with loopback disabled under all receiver gain ranges; and with the line shorted (S1 closed in Figure 4).
POWER DISSIPATION
Approximately 75% of the power dissipation in the AFE1103 is in the analog circuitry, and this component does not change with clock frequency. However, the power dissipa-
tion in the digital circuitry does decrease with lower clock frequency. In addition, the power dissipation in the digital section is decreased when operating from a smaller supply voltage, such as 3.3V. (The analog supply, AVDD, must remain in the range 4.75V to 5.25V.) The power dissipation listed in the specifications section applies under these normal operating conditions: 5V Analog Power Supply; 3.3V Digital Power Supply; standard 13.5dBm delivered to the line; and a pseudo-random equiprobable sequence of HDSL output pulses. The power dissipation specifications includes all power dissipated in the AFE1103, it does not include power dissipated in the external load.
The external power is 16.5dBm, 13.5dBm to the line and 13.5dBm to the impedance matching resistors. The external load power of 16.5dBm is 45mW. The typical power dissipation in the AFE1103 under various conditions is shown in Table I.

TABLE I. Typical Power Dissipation.

FIGURE 4. Uncancelled Echo Test Diagram.
Page 10
LAYOUT
The analog front end of an HDSL system has a number of conflicting requirements. It must accept and deliver digital outputs at fairly high rates of speed, phase-lock to a highspeed digital clock, and convert the line input to a highprecision (14-bit) digital output. Thus, there are really three sections of the AFE1103: the digital section, the phaselocked loop, and the analog section. The power supply for the digital section of the AFE1103 can range from 3.3V to 5V. This supply should be decoupled to digital ground with a ceramic 0.1µF capacitor placed as close to DGND (pin 12) and DVDD (pin 13) as possible. Ideally, both a digital power supply plane and a digital
ground plane should run up to and underneath the digital pins of the AFE11103 (pins 3 through 26). However, DVDD may be supplied by a wide printed circuit board (PCB) trace. A digital ground plane underneath all digital pins is strongly recommended. The phase-locked loop is powered from PVDD (pin 2) and its ground is referenced to PGND (pin 1). Note that PVDD must be in the 4.75V to 5.25V range. This portion of the AFE1103 should be decoupled with both a 10µF Tantalum capacitor and a 0.1µF ceramic capacitor. The ceramic capacitor should be placed as close to the AFE1103 as possible. The placement of the Tantalum capacitor is not as critical, but should be close. In each case, the capacitor should be connected
between PVDD and PGND.
In most systems, it will be natural to derive PVDD from the AVDD supply. A 5Ω to 10Ω resistor should be used to connect PVDD to the analog supply. This resistor in combination with the 10µF capacitor form a lowpass filter— keeping glitches on AVDD from affecting PVDD. Ideally, PVDD would originate from the analog supply (via the resistor) near the power connector for the printed circuit board. Likewise, PGND should connect to a large PCB trace or small ground plane which returns to the power supply connector underneath the PVDD supply path. The PGND “ground plane” should also extend underneath PLLIN and PLLOUT (pins 47 and 48). The remaining portion of the AFE1103 should be considered
analog. All AGND pins should be connected directly to a common analog ground plane and all AVDD pins should be connected to an analog 5V power plane. Both of these planes should have a low impedance path to the power supply. Ideally, all ground planes and traces and all power planes and traces should return to the power supply connector before being connected together (if necessary). Each ground and power pair should be routed over each other, should not overlap any portion of another pair, and the pairs should be separated by a distance of at least 0.25 inch (6mm). One exception is that the digital and analog ground planes should be connected together underneath the AFE1103 by a small
trace.