ADS8320 BURR-BROWN
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 13
Technical content
DESCRIPTION
The ADS8320 is a 16-bit sampling analog-to-digital converter (A/D) with guaranteed specifications over a 2.7V to 5.25V supply range. It requires very little power even when operating at the full 100kHz data rate. At lower data rates, the high speed of the device enables it to spend most of its time in the power-down mode—the average power dissipation is less than 100µW at 10kHz data rate. The ADS8320 also features operation from 2.0V to 5.25V, a synchronous serial (SPI/SSI compatible) in- terface, and a differential input. The reference voltage can be set to any level within the range of 500mV to V CC . Ultra-low power and small size make the ADS8320 ideal for portable and battery-operated systems. It is also a perfect fit for remote data acquisition mod- ules, simultaneous multi-channel systems, and iso- lated data acquisition. The ADS8320 is available in an MSOP-8 package. 16-Bit, High-Speed, 2.7V to 5V microPower Sampling ANALOG-TO-DIGITAL CONVERTER © 1999 Burr-Brown Corporation PDS-1504C Printed in U.S.A. May, 2000
FEATURES
l MICRO POWER: 1.8mW at 100kHz and 2.7V 0.3mW at 10kHz and 2.7V l POWER DOWN: 3 µA max l MSOP-8 PACKAGE l PIN-COMPATIBLE TO ADS7816 AND ADS7822 l SERIAL (SPI/SSI) INTERFACE SAR Control Serial Interface D OUT ComparatorS/H Amp CS/SHDN DCLOCK +In VREF –In CDAC
APPLICATIONS
l BATTERY OPERATED SYSTEMS l REMOTE DATA ACQUISITION l ISOLATED DATA ACQUISITION l SIMULTANEOUS SAMPLING, MULTI-CHANNEL SYSTEMS l INDUSTRIAL CONTROLS l ROBOTICS l VIBRATION ANALYSIS International Airport Industrial Park • Mailing Address: PO Box 11400, Tucson, AZ 85734 • Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 • Tel: (520) 746-1111 Twx: 910-952-1111 • Internet: http://www.burr-brown.com/ • Cable: BBRCORP • Telex: 066-6491 • FAX: (520) 889-1510 • Immediate Product Info: (800) 548-6132 For most current data sheet and other product information, visit www.burr-brown.com
SPECIFICATIONS: +V CC = +5V At –40°C to +85°C, VREF = +5V,–IN = GND, fSAMPLE = 100kHz, and fCLK = 24 • fSAMPLE , unless otherwise specified. The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant any BURR-BROWN product for use in life support devices and/or systems. ADS8320E ADS8320EB PARAMETER CONDITIONS MIN TYP MAX MIN TYP MAX UNITS RESOLUTION 16 [ Bits ANALOG INPUT Full-Scale Input Span +In – (–In) 0 V REF [[ V Absolute Input Range +In –0.1 VCC + 0.1 [[ V –In –0.1 +1.0 [[ V Capacitance 45 [ pF Leakage Current 1 [ nA SYSTEM PERFORMANCE No Missing Codes 14 15 Bits Integral Linearity Error ±0.008 ±0.018 ±0.006 ±0.012 % of FSR Offset Error ±1 ±2 ±0.5 ±1m V Offset Temperature Drift ±3 [ µV/°C Gain Error ±0.05 ±0.024 % Gain Temperature Drift ±0.3 [ ppm/°C Noise 20 [ µVrms Power Supply Rejection Ratio +4.7V < V CC < 5.25V 3 [ LSB (1) SAMPLING DYNAMICS Conversion Time 16 [ Clk Cycles Acquisition Time 4.5 [ Clk Cycles Throughput Rate 100 [ kHz Clock Frequency Range 0.024 2.9 [[ MHz DYNAMIC CHARACTERISTICS Total Harmonic Distortion V IN = 5Vp-p at 10kHz –84 –86 dB SINAD V IN = 5Vp-p at 10kHz 82 84 dB Spurious Free Dynamic Range V IN = 5Vp-p at 10kHz 84 86 dB SNR 90 92 dB REFERENCE INPUT Voltage Range 0.5 V CC [[ V Resistance CS = GND, fSAMPLE = 0Hz 5 [ G Ω CS = VCC 5 [ G Ω Current Drain 40 80 [[ µA fSAMPLE = 10kHz 0.8 [ µA CS = VCC 0.1 3 [ µA DIGITAL INPUT/OUTPUT Logic Family CMOS [ Logic Levels: VIH IIH = +5µA 3.0 VCC + 0.3 [[ V VIL IIL = +5µA –0.3 0.8 [[ V VOH IOH = –250µA 4.0 [ V VOL IOL = 250µA 0.4 [ V Data Format Straight Binary [ POWER SUPPLY REQUIREMENTS VCC Specified Performance 4.75 5.25 [[ V VCC Range(2) 2.0 5.25 [[ V Quiescent Current 900 1700 [[ µA fSAMPLE = 10kHz(3, 4) 200 [ µA Power Dissipation 4.5 8.5 [[ mW Power Down CS = V CC 0.3 3 [[ µA TEMPERATURE RANGE Specified Performance –40 +85 [[ °C [ Specifications same as ADS8320E. NOTES: (1) LSB means Least Significant Bit. (2) See Typical Performance Curves for more information. (3) fCLK = 2.4MHz, CS = VCC for 216 clock cycles out of every 240. (4) See the Power Dissipation section for more information regarding lower sample rates.
SPECIFICATIONS: +V CC = +2.7V At –40°C to +85°C, VREF = 2.5V, –IN = GND, fSAMPLE = 100kHz, and fCLK = 24 • fSAMPLE , unless otherwise specified. ADS8320E ADS8320EB PARAMETER CONDITIONS MIN TYP MAX MIN TYP MAX UNITS RESOLUTION 16 [ Bits ANALOG INPUT Full-Scale Input Span +In – (–In) 0 V REF [[ V Absolute Input Range +In –0.1 VCC + 0.1 [[ V –In –0.1 +0.5 [[ V Capacitance 45 [ pF Leakage Current 1 [ nA SYSTEM PERFORMANCE No Missing Codes 14 15 Bits Integral Linearity Error ±0.008 ±0.018 ±0.006 ±0.012 % of FSR Offset Error ±1 ±2 ±0.5 ±1m V Offset Temperature Drift ±3 [ µV/°C Gain Error ±0.05 ±0.024 % of FSR Gain Temperature Drift ±0.3 [ ppm/°C Noise 20 [ µVrms Power Supply Rejection Ratio +2.7V < V CC < +3.3V 3 [ LSB (1) SAMPLING DYNAMICS Conversion Time 16 [ Clk Cycles Acquisition Time 4.5 [ Clk Cycles Throughput Rate 100 [ kHz Clock Frequency Range 0.024 2.4 [[ MHz DYNAMIC CHARACTERISTICS Total Harmonic Distortion V IN = 2.7Vp-p at 1kHz –86 –88 dB SINAD V IN = 2.7Vp-p at 1kHz 84 86 dB Spurious Free Dynamic Range V IN = 2.7Vp-p at 1kHz 86 88 dB SNR 88 90 dB REFERENCE INPUT Voltage Range 0.5 V CC [[ V Resistance CS = GND, fSAMPLE = 0Hz 5 [ G Ω CS = VCC 5 [ G Ω Current Drain 20 50 [[ µA CS = VCC 0.1 3 [[ µA DIGITAL INPUT/OUTPUT Logic Family CMOS [ Logic Levels: VIH IIH = +5µA 2.0 VCC + 0.3 [[ V VIL IIL = +5µA –0.3 0.8 [[ V VOH IOH = –250µA 2.1 [ V VOL IOL = 250µA 0.4 [ V Data Format Straight Binary [ POWER SUPPLY REQUIREMENTS VCC Specified Performance 2.7 3.3 [[ V VCC Range(3) 2.0 5.25 [[ V See Note 2 2.0 2.7 [[ V Quiescent Current 650 1300 [[ µA fSAMPLE = 10kHz(4,5) 100 [ µA Power Dissipation 1.8 3.8 [[ mW Power Down CS = V CC 0.3 3 [[ µA TEMPERATURE RANGE Specified Performance –40 +85 [[ °C [ Specifications same as ADS8320E. Notes: (1) LSB means Least Significant Bit. With VREF equal to +5V, one LSB is 0.039mV. (2) The maximum clock rate of the ADS8320 is less than 2.4MHz in this power supply range. (3) See the Typical Performance Curves for more information. (4) fCLK = 2.4MHz, CS = VCC for 216 clock cycles out of every 240. (5) See the Power Dissipation section for more information regarding lower sample rates.
Electrostatic discharge can cause damage ranging from per- formance degradation to complete device failure. Burr- Brown Corporation recommends that all integrated circuits be handled and stored using appropriate ESD protection methods. ESD damage can range from subtle performance degrada- tion to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet published specifications. ABSOLUTE MAXIMUM RATINGS (1) NOTE: (1) Stresses above these ratings may permanently damage the device. PIN NAME DESCRIPTION 1V REF Reference Input. 2 +In Non Inverting Input. 3 –In Inverting Input. Connect to ground or to remote ground sense point. 4 GND Ground.
5 CS/SHDN Chip Select when LOW, Shutdown Mode when
HIGH. OUT The serial output data word is comprised of 16 bits of data. In operation the data is valid on the falling edge of DCLOCK. The second clock pulse after the falling edge of CS enables the serial output. After one null bit the data is valid for the next 16 edges.
7 DCLOCK Data Clock synchronizes the serial data transfer
and determines conversion speed. 8+ V CC Power Supply. PIN ASSIGNMENTS PIN CONFIGURATION Top View MSOP +VCC DCLOCK D OUT CS/SHDN VREF +In –In GND ADS8320 PACKAGE/ORDERING INFORMATION MAXIMUM NO INTEGRAL MISSING LINEARITY CODE PACKAGE SPECIFICATION ERROR ERROR DRAWING TEMPERATURE PACKAGE ORDERING TRANSPORT PRODUCT (%) (LSB) PACKAGE NUMBER (1) RANGE MARKING (2) NUMBER (3) MEDIA ADS8320E 0.018 14 MSOP-8 337 –40 °C to +85°C A20 ADS8320E/250 Tape and Reel ADS8320E """ """ ADS8320E/2K5 Tape and Reel ADS8320EB 0.012 15 MSOP-8 337 –40 °C to +85°C A20 ADS8320EB/250 Tape and Reel ADS8320EB """ """ ADS8320EB/2K5 Tape and Reel NOTE: (1) For detail drawing and dimension table, please see end of data sheet or Package Drawing File on Web. (2) Performance Grade information is marked on the reel. (3) Models with a slash(/) are available only in Tape and reel in quantities indicated (e.g. /250 indicates 250 units per reel, /2K5 indicates 2500 devices per reel). Ordering 2500 pieces of ”ADS8320E/2K5“ will get a single 2500-piece Tape and Reel. For detailed Tape and Reel mechanical information, refer to the www.burr-brown.com web site under Applications and Tape and Reel Orientation and Dimensions.
TYPICAL PERFORMANCE CURVES At TA = +25°C, VCC = +5V, VREF = +5V, fSAMPLE = 100kHz, fCLK = 24 • fSAMPLE , unless otherwise specified. INTEGRAL LINEARITY ERROR vs CODE (+25 °C) 2 0 1.0 0.0 –1.0 –2.0 –3.0 –4.0 –5.0 –6.0 Integral Linearity Error (LSB) 0000H 8000H C000 H4000H FFFF H Hex Code DIFFERENTIAL LINEARITY ERROR vs CODE (+25 °C) 3.0 2.0 1.0 0.0 –1.0 –2.0 –3.0 Differential Linearity Error (LSB) 0000H 8000H C000 H4000H FFFF H Hex Code SUPPLY CURRENT vs TEMPERATURE 1200 1000 800 600 400 200 Supply Current (µA) –50 –25 0 25 50 75 100 Temperature (°C) 2.7V POWER DOWN SUPPLY CURRENT vs TEMPERATURE 600 500 400 300 200 100 Supply Current (nA) –50 –25 0 25 50 75 100 Temperature (°C) QUIESCENT CURRENT vs V CC 1200 1000 800 600 400 200 Quiescent Current (µA) 12345 VCC (V) MAXIMUM SAMPLE RATE vs V CC 1000 100 Sample Rate (kHz) 12345 VCC (V)
TYPICAL PERFORMANCE CURVES (Cont.) At TA = +25°C, VCC = +2.7V, VREF = +2.5V, fSAMPLE = 100kHz, fCLK = 24 • fSAMPLE , unless otherwise specified. CHANGE IN OFFSET vs REFERENCE VOLTAGE Change in Offset (LSB) 12345 Reference Voltage (V) VCC = 5V CHANGE IN OFFSET vs TEMPERATURE Delta from 25°C (LSB) –50 –25 0 25 50 75 100 Temperature (°C) 2.7V CHANGE IN GAIN vs REFERENCE VOLTAGE Change in Gain (LSB) 12345 Reference Voltage (V) VCC = 5V FREQUENCY SPECTRUM (8192 Point FFT, FIN = 10.120kHz, –0.3dB) –20 –40 –60 –80 –100 –120 –140 Amplitude (dB) 0 1 02 0 3 0 4 05 0 Frequency (kHz) PEAK-TO-PEAK NOISE vs REFERENCE VOLTAGE Peak-to-Peak Noise (LSB) 0.1 1 10 Reference Voltage (V) VCC = 5V CHANGE IN GAIN vs TEMPERATURE Delta from 25°C (LSB) –50 –25 0 25 50 75 100 Temperature (°C) 2.7V
TYPICAL PERFORMANCE CURVES (Cont.) At TA = +25°C, VCC = +5V, VREF = +5V, fSAMPLE = 100kHz, fCLK = 24 • fSAMPLE , unless otherwise specified. TOTAL HARMONIC DISTORTION vs FREQUENCY –10 –20 –30 –40 –50 –60 –70 –80 –90 –100 Total Harmonic Distortion (dB) 1 10 100 Frequency (kHz) SIGNAL-TO-(NOISE + DISTORTION) vs FREQUENCY 100 Signal-to-(Noise + Distortion) (dB) 1 10 50 100 Frequency (kHz) SIGNAL-TO-(NOISE + DISTORTION) vs INPUT LEVEL Signal-to-(Noise + Distortion) (dB) Input Level (dB) REFERENCE CURRENT vs SAMPLE RATE Reference Current (µA) 0 20 40 60 80 100 Sample Rate (kHz) 2.7V REFERENCE CURRENT vs TEMPERATURE Reference Current (µA) –50 –25 0 25 50 75 100 Temperature (°C) 2.7V SPURIOUS FREE DYNAMIC RANGE AND SIGNAL-TO-NOISE RATIO vs FREQUENCY 100 Spurious Free Dynamic Range and Signal-to-Noise Ratio (dB) 1 10 100 50 Frequency (kHz) Signal-to-Noise Ratio Spurious Free Dynamic Range
The ADS8320 is a classic successive approximation register (SAR) analog-to-digital (A/D) converter. The architecture is based on capacitive redistribution which inherently includes a sample/hold function. The converter is fabricated on a 0.6µ CMOS process. The architecture and process allow the ADS8320 to acquire and convert an analog signal at up to 100,000 conversions per second while consuming less than 4.5mW from +V CC . The ADS8320 requires an external reference, an external clock, and a single power source (VCC ). The external refer- ence can be any voltage between 500mV and VCC . The value of the reference voltage directly sets the range of the analog input. The reference input current depends on the conversion rate of the ADS8320. The external clock can vary between 24kHz (1kHz through- put) and 2.4MHz (100kHz throughput). The duty cycle of the clock is essentially unimportant as long as the minimum high and low times are at least 200ns (V CC = 2.7V or greater). The minimum clock frequency is set by the leakage on the capacitors internal to the ADS8320. The analog input is provided to two input pins: +In and –In. When a conversion is initiated, the differential input on these pins is sampled on the internal capacitor array. While a conversion is in progress, both inputs are disconnected from any internal function. The digital result of the conversion is clocked out by the DCLOCK input and is provided serially, most significant bit first, on the D OUT pin. The digital data that is provided on the D OUT pin is for the conversion currently in progress—there is no pipeline delay. It is possible to continue to clock the ADS8320 after the conversion is complete and to obtain the serial data least significant bit first. See the digital timing section for more information. ANALOG INPUT The +In and –In input pins allow for a differential input signal. Unlike some converters of this type, the –In input is not re-sampled later in the conversion cycle. When the converter goes into the hold mode, the voltage difference between +In and –In is captured on the internal capacitor array. The range of the –In input is limited to –0.1V to +1V (–0.1V to +0.5V when using a 2.7V supply). Because of this, the differential input can be used to reject only small signals that are common to both inputs. Thus, the –In input is best used to sense a remote signal ground that may move slightly with respect to the local ground potential. The input current on the analog inputs depends on a number of factors: sample rate, input voltage, source impedance, and power-down mode. Essentially, the current into the ADS8320 charges the internal capacitor array during the sample pe- riod. After this capacitance has been fully charged, there is no further input current. The source of the analog input voltage must be able to charge the input capacitance (45pF) to a 16-bit settling level within 4.5 clock cycles. When the converter goes into the hold mode or while it is in the power- down mode, the input impedance is greater than 1GΩ . Care must be taken regarding the absolute analog input voltage. To maintain the linearity of the converter, the –In input should not drop below GND – 100mV or exceed GND + 1V. The +In input should always remain within the range of GND – 100mV to V CC + 100mV. Outside of these ranges, the converter’s linearity may not meet specifications. To minimize noise, low bandwidth input signals with low- pass filters should be used. REFERENCE INPUT The external reference sets the analog input range. The ADS8320 will operate with a reference in the range of 500mV to V CC . There are several important implications of this. As the reference voltage is reduced, the analog voltage weight of each digital output code is reduced. This is often referred to as the Least Significant Bit (LSB) size and is equal to the reference voltage divided by 65,536. This means that any offset or gain error inherent in the A/D converter will appear to increase, in terms of LSB size, as the reference voltage is reduced. The noise inherent in the converter will also appear to increase with lower LSB size. With a +5V reference, the internal noise of the converter typically contributes only 1.5 LSB peak-to-peak of potential error to the output code. When the external reference is 500mV, the potential error contribution from the internal noise will be 10 times larger— 15 LSBs. The errors due to the internal noise are gaussian in nature and can be reduced by averaging consecutive conver- sion results. For more information regarding noise, consult the typical performance curve “Peak-to-Peak Noise vs Reference Volt- age.” Note that the Effective Number of Bits (ENOB) figure is calculated based on the converter’s signal-to-(noise + distortion) ratio with a 1kHz, 0dB input signal. SINAD is related to ENOB as follows: SINAD = 6.02 • ENOB + 1.76 With lower reference voltages, extra care should be taken to provide a clean layout including adequate bypassing, a clean power supply, a low-noise reference, and a low-noise input signal. Because the LSB size is lower, the converter will also be more sensitive to external sources of error such as nearby digital signals and electromagnetic interference.
FIGURE 3. ADS8320 Basic Timing Diagrams. TABLE II. Ideal Input Voltages and Output Codes. A falling CS signal initiates the conversion and data transfer. a least significant bit first format. been taken HIGH and returned LOW. the effects of offset, gain error, or noise. are several things to keep in mind. rate that will satisfy the requirements of the system. the power down mode is entered. NOTE: Minimum 22 clock cycles required for 16-bit conversion. Shown are 24 clock cycles. If CS remains LOW at the end of conversion, a new datastream with LSB-first is shifted out again.
FIGURE 4. Timing Diagrams and Test Circuits for the Parameters in Table I. internal conditions such that the output is LOW unless disabled by the output control.