ADS1201 BURR-BROWN

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 13

Technical content

© 1997 Burr-Brown Corporation PDS-1417C Printed in U.S.A. October, 1999 International Airport Industrial Park • Mailing Address: PO Box 11400, Tucson, AZ 85734 • Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 • Tel: (520) 746-1111 Twx: 910-952-1111 • Internet: http://www.burr-brown.com/ • Cable: BBRCORP • Telex: 066-6491 • FAX: (520) 889-1510 • Immediate Product Info: (800) 548-6132 High Dynamic Range DELTA-SIGMA MODULATOR ADS1201 +2.5V Reference Bias Generator Second-Order ΔΣ Modulator AV DD AGND REF OUTREF IN VBIAS CAL GAIN/OFFSET DGND DV DD AINP AINN MOUT BIASEN REF EN MCLK

DESCRIPTION

The ADS1201 is a precision, 130dB dynamic range, delta-sigma (ΔΣ ) modulator operating from a single +5V supply. The differential inputs are ideal for direct connection to transducers or low level signals. With the appropriate digital filter and modulator rate, the device can be used to achieve 24-bit analog-to-digital (A/D) conversion with no missing codes. Effective resolution of 20 bits can be maintained with a digital filter bandwidth of 1kHz at a modulator rate of 320kHz. The ADS1201 is designed for use in high resolution measurement applications including smart transmit- ters, industrial process control, weigh scales, chroma- tography, and portable instrumentation. It is available in a 16-lead SOIC package.

FEATURES

l FULLY DIFFERENTIAL INPUT l TWO-WIRE INTERFACE l INTERNAL/EXTERNAL REFERENCE l ON-CHIP SWITCHES FOR CALIBRATION

APPLICATIONS

l INDUSTRIAL PROCESS CONTROL l INSTRUMENTATION l SMART TRANSMITTERS l PORTABLE INSTRUMENTS l WEIGH SCALES l PRESSURE TRANSDUCERS

At TA = +25°C, AVDD = DVDD = +5V, MCLK = 320kHz, REFEN LOW, BIAS EN LOW, and external +2.5V reference, unless otherwise specified. The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant any BURR-BROWN product for use in life support devices and/or systems. SPECIFICATIONS ADS1201U PARAMETER CONDITIONS MIN TYP MAX UNITS ANALOG INPUT Absolute Input Voltage Range 0 +5 V With VBIAS(1) –10 +10 V Differential Input Voltage Range –5 +5 V With VBIAS(1) –20 See Note 2 +20 V Input Impedance 250(4) kΩ Input Capacitance 8p F Input Leakage Current 55 0p A At TMIN to TMAX 1n A SYSTEM PERFORMANCE Dynamic Range 10Hz Bandwidth (5) 130(6) dB 60Hz Bandwidth(5) 115(6) 120(6) dB 1kHz Bandwidth(5) 115(6) dB Integral Linearity Error 60Hz Bandwidth (5) ±0.0015 %FSR 1kHz Bandwidth(5) ±0.0015 %FSR Offset Error(2) See Note 7 µV Offset Drift(3) 1 µV/°C Gain Error(2) See Note 7 ppm Gain Error Drift(3) 1 µV/°C Common-Mode Rejection At DC 80 100 dB Power Supply Rejection 80 dB REFERENCE Internal Reference (REF OUT ) 2.4 2.5 2.6 V Drift 25 ppm/ °C Noise 50 µVp-p Load Current Source or Sink –1 1 mA Output Impedance 2 Ω External Reference (REF IN) 2.0 3.0 V Load Current 2.5 µA VBIAS Output Using Internal Reference 3.15 3.3 3.45 V Drift 50 ppm/ °C Load Current 10 mA DIGITAL INPUT/OUTPUT Logic Family TTL Compatible CMOS Logic Levels: VIH (MCLK) I IH = +5µA 2.0 DV DD +0.3 V VIL (MCLK) I IL = +5µA –0.3 0.8 V VOH (MOUT) I OH = 2 TTL Loads 2.4 V VOL (MOUT) I OL = 2 TTL Loads 0.4 V MCLK Frequency 0.02 1 MHz POWER SUPPLY REQUIREMENTS Power Supply Voltage Specified Performance 4.75 5.25 V Supply Current Analog Current 4.6 mA Digital Current 0.4 mA Additional Analog Current REF OUT Enabled No Load 1.6 mA VBIAS Enabled No Load 1 mA Total Power Dissipation REF OUT , VBIAS Disabled 25 40 mW TEMPERATURE RANGE Specified Performance –40 +85 °C NOTES: (1) This range is set with external resistors and VBIAS (as described in the text). Other ranges are possible. (2) After the on-chip offset and gain calibration functions have been employed. (3) Re-calibration can reduce these errors. (4) Input impedance changes with MCLK. (5) Assume brick wall digital filter is used. (6) 20 Log (full scale/rms noise). (7) After calibration, these errors will be of the order of the effective resolution.

±10mA, Continuous NOTE: (1) Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. Exposure to absolute maximum conditions for extended periods may affect device reliability. ABSOLUTE MAXIMUM RATINGS ELECTROSTATIC DISCHARGE SENSITIVITY This integrated circuit can be damaged by ESD. Burr-Brown recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. PACKAGE SPECIFIED DRAWING TEMPERATURE PACKAGE ORDERING TRANSPORT PRODUCT PACKAGE NUMBER RANGE MARKING NUMBER (1) MEDIA ADS1201U SOL-16 211 –40 °C to +85°C ADS1201U ADS1201U Rails "" " " " ADS1201U/1K Tape and Reel NOTE: (1) Models with a slash (/) are available only in Tape and Reel in the quantities indicated (e.g., /1K indicates 1000 devices per reel). Ordering 1000 pieces of “ADS1201U/1K” will get a single 1000-piece Tape and Reel. PACKAGE/ORDERING INFORMATION PIN CONFIGURATION Top View SOIC 1A V DD Analog Input: Analog Supply, +5V nominal.

2 REF OUT Analog Output: Internal Reference Voltage Output:

+2.5V nominal. 3 REF IN Analog Input: Reference Voltage Input. 4 NIC Not Internally Connected. INP Analog Input: Noninverting Input. 6A INN Analog Input: Inverting Input. 7 AGND Analog Input: Analog Ground. BIAS Analog Output: Bias Voltage Output, nominally +3.3V (with +2.5V reference).

9 BIAS EN Digital Input: Bias Voltage Enable Input (HIGH =

enabled, LOW = disabled).

10 GAIN/OFFSET Digital Input: Gain/Offset Calibration Select Input

(with CAL LOW; HIGH = gain configuration, LOW = offset configuration).

11 CAL Digital Input: Calibration Control Input (HIGH =

normal operation, LOW = gain or offset calibration configuration). 12 DGND Digital Input: Digital Ground. 13 DV DD Digital Input: Digital Supply, +5V nominal. 14 MCLK Digital Input: Modulator Clock Input. CMOS compatible. 15 MOUT Digital Output: Modulator Output.

16 REF EN Digital Input: REFOUT Voltage Enable Input

(HIGH = enabled, LOW = disabled). PIN DESCRIPTIONS PIN NO NAME DESCRIPTION ADS1201 AV DD REF OUT REF IN NIC AINP AINN AGND VBIAS REF EN MOUT MCLK DV DD DGND CAL GAIN/OFFSET BIAS EN

TYPICAL PERFORMANCE CURVES At TA = +25°C, AVDD = DVDD = +5V, MCLK = 320kHz, REFEN LOW, BIAS EN LOW, and external +2.5V reference, unless otherwise specified. 1.2 0.8 0.6 0.4 0.2 rms NOISE V DIN (V) – 5 – 4 – 3 – 2 – 1 012345 (ppm) 1.5 1.0 0.5 –0.5 –1.0 –1.5 –2.0 –2.5 –3.0 –3.5 LINEARITY V DIN (V) – 5 – 4 – 3 – 2 – 1 012345 (ppm) 110 105 100 CMRR vs FREQUENCY Frequency (Hz) 0.1 1 10 100 1000 CMRR (dB) PSRR vs FREQUENCY Frequency (Hz) 0.1 1.0 10 100 1k 10k 100k PSRR (dB) TYPICAL SINK CURRENT V OL (V) IOUT (mA) TYPICAL SOURCE CURRENT V OL (V) IOUT (mA)

FIGURE 1. Connection Diagram for the ADS1201 Delta-Sigma Modulator Including External Processor. At TA = +25°C, AVDD = DVDD = +5V, MCLK = 320kHz, REFEN LOW, BIAS EN LOW, and external +2.5V reference, unless otherwise specified. that exceeds 130dB (see Figure 1). which digitizes the input signal into a binary output stream. sents the analog input voltage over time.

FIGURE 8. Analog Input versus Modulator Output of the ADS1201. FIGURE 9. Timing Diagram for the Calibration Feature of the ADS1201. BIAS should not exceed 10mA. or AINN) should be used in the calculation. data, which is a serial stream, is available on the MOUT pin. Typically, MOUT is read on the falling edge of MCLK. kept constant for reliable, repeatable results. there is a “significant” change in the operating environment.

2.5 TMCLK (1)

NOTE: (1) TMCLK is the clock period of MCLK.

referenced to VREF internally. TABLE III. Calibration Enable. and effective resolution of the system. Figure 10. In this circuit, a connection has been made The analog supply should be well regulated and low noise. resistors should be used to limit the input current. mine the appropriate connection between AVDD and DVDD . the appropriate connection between AGND and DGND.