ADS1112 BURR-BROWN

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 18

Technical content

FEATURES

/C0068COMPLETE DATA ACQUISITION SYSTEM IN THE MSOP-10 AND LEADLESS QFN-STYLE PACKAGES /C0068MEASUREMENTS FROM TWO DIFFERENTIAL CHANNELS OR THREE SINGLE-ENDED CHANNELS /C0068I2C INTERFACE—EIGHT ADDRESSES PIN- SELECTABLE /C0068ONBOARD REFERENCE: Accuracy: 2.048V ±0.05% Drift: 5ppm/°C /C0068ONBOARD PGA /C0068ONBOARD OSCILLATOR /C006816 BITS, NO MISSING CODES /C0068INL: 0.01% of FSR max /C0068CONTINUOUS SELF-CALIBRATION /C0068SINGLE-CYCLE CONVERSION /C0068PROGRAMMABLE DATA RATE: 15SPS to 240SPS /C0068POWER SUPPLY: 2.7V to 5.5V /C0068LOW CURRENT CONSUMPTION: 240 µA

APPLICATIONS

/C0068PORTABLE INSTRUMENTATION /C0068INDUSTRIAL PROCESS CONTROL /C0068SMART TRANSMITTERS /C0068CONSUMER GOODS /C0068FACTORY AUTOMATION /C0068TEMPERATURE MEASUREMENT

DESCRIPTION

The ADS1112 is a precision, continuously self-calibrating Analog-to-Digital (A/D) converter with two differential or three single-ended channels and up to 16 bits of resolution in the small MSOP-10 and leadless QFN-style (small-outline, no-lead) packages. The onboard 2.048V reference provides an input range of ±2.048V differentially. The ADS1112 uses an I 2C-compatible serial interface and has two address pins that allow a user to select one of the eight I2C Slave addresses. The ADS1112 operates from a single power supply ranging from 2.7V to 5.5V. The ADS1112 can perform conversions at rates of 15, 30, 60, or 240 samples per second (SPS). The o nboard programmable gain amplifier (PGA), which offers gains of up to eight, allows smaller signals to be measured with high resolution. In single-conversion mode, the ADS1112 automatically powers down after a conversion, greatly reducing current consumption during idle periods. The ADS1112 is designed for applications requiring high-resolution measurement, where space and power consumption are major considerations. Typical applications include portable instrumentation, industrial process control, and smart transmitters.All trademarks are the property of their respective owners. ADS1112 SBAS282D − JUNE 2003 − REVISED MARCH 2004 16-Bit Analog-to-Digital Converter with Input Multiplexer and Onboard Reference www.ti.com Copyright  2003−2004, Texas Instruments Incorporated Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. /C0080/C0082/C0079/C0068/C0085/C0067/C0084/C0073/C0079/C0078 /C0068/C0065/C0084/C0065 /C0105/C0110/C0102/C0111/C0114/C0109/C0097/C0116/C0105/C0111/C0110 /C0105/C0115 /C0099/C0117/C0114/C0114/C0101/C0110/C0116 /C0097/C0115 /C0111/C0102 /C0112/C0117/C0098/C0108/C0105/C0099/C0097/C0116/C0105/C0111/C0110 /C0100/C0097/C0116/C0101/C0046 /C0080/C0114/C0111/C0100/C0117/C0099/C0116/C0115 /C0099/C0111/C0110/C0102/C0111/C0114/C0109 /C0116/C0111 /C0115/C0112/C0101/C0099/C0105/C0102/C0105/C0099/C0097/C0116/C0105/C0111/C0110/C0115 /C0112/C0101/C0114 /C0116/C0104/C0101 /C0116/C0101/C0114/C0109/C0115 /C0111/C0102 /C0084/C0101/C0120/C0097/C0115 /C0073/C0110/C0115/C0116/C0114/C0117/C0109/C0101/C0110/C0116/C0115 /C0115/C0116/C0097/C0110/C0100/C0097/C0114/C0100 /C0119/C0097/C0114/C0114/C0097/C0110/C0116/C0121/C0046 /C0080/C0114/C0111/C0100/C0117/C0099/C0116/C0105/C0111/C0110 /C0112/C0114/C0111/C0099/C0101/C0115/C0115/C0105/C0110/C0103 /C0100/C0111/C0101/C0115 /C0110/C0111/C0116 /C0110/C0101/C0099/C0101/C0115/C0115/C0097/C0114/C0105/C0108/C0121 /C0105/C0110/C0099/C0108/C0117/C0100/C0101 /C0116/C0101/C0115/C0116/C0105/C0110/C0103 /C0111/C0102 /C0097/C0108/C0108 /C0112/C0097/C0114/C0097/C0109/C0101/C0116/C0101/C0114/C0115/C0046

/C0065/C0068/C0083/C0049/C0049/C0049/C0050 SBAS282D − JUNE 2003 − REVISED MARCH 2004 www.ti.com ABSOLUTE MAXIMUM RATINGS (1) VDD to GND −0.3V to +6V Input Current 100mA, Momentary Input Current 10mA, Continuous Analog Inputs, A0, A1, Voltage to GND−0.3V to VDD + 0.3V SDA, SCL Voltage to GND −0.5V to 6V Maximum Junction Temperature +150°C Operating Temperature Range −40°C to +125°C Storage Temperature Range −60°C to +150°C Lead Temperature (soldering, 10s) +300°C (1)Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to absolute maximum conditions for extended periods may affect device reliability. This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. PACKAGE/ORDERING INFORMATION PRODUCT PACKAGE-LEAD PACKAGE DESIGNATOR (1) SPECIFIED TEMPERATURE RANGE PACKAGE MARKING ORDERING NUMBER TRANSPORT MEDIA, QUANTITY ADS1112 MSOP-10 DGS −40°C to +85°C BHU ADS1112IDGST Tape and Reel, 250 ADS1112 MSOP-10 DGS −40°C to +85°C BHU ADS1112IDGSR Tape and Reel, 2500 ADS1112 SON-10 DRC −40°C to +85°C BHV ADS1112IDRCT Tape and Reel, 250 ADS1112 SON-10 DRC −40°C to +85°C BHV ADS1112IDRCR Tape and Reel, 3000 (1)For the most current specification and package information, refer to our web site at www .ti.com. Top View MSOP-10 Top View SON-10 Terminal Functions TERMINAL NAME NO. DESCRIPTION AIN0 1 Differential Channel 1; Positive Input Single-ended Channel 1 Input AIN1 2 Differential Channel 1; Negative Input Single -ended Channel 2 Input GND 3 Ground AIN2 4 Differential Channel 2; Positive Input Single -ended Channel 3 Input AIN3 5 Differential Channel 2; Negative Input Single -ended Common Input VDD 6 Power Supply: 2.7V to 5.5V SDA 7 Serial Data: Transmits and receives data SCL 8 Serial Clock Input: Clocks output data on SDA A0 9 I2C Slave Address Select A1 10 I2C Slave Address Select

/C0065/C0068/C0083/C0049/C0049/C0049/C0050 SBAS282D − JUNE 2003 − REVISED MARCH 2004 www.ti.com

ELECTRICAL CHARACTERISTICS

All specifications at −40°C to +85°C, VDD = 5V, and all PGAs, unless otherwise noted. ADS1112 PARAMETER CONDITIONS MIN TYP MAX UNIT ANALOG INPUT Full-Scale Input Voltage (VIN+) − (VIN−) ±2.048/PGA V Analog Input Voltage VIN+ to GND or VIN− to GND GND − 0.2 VDD + 0.2 V Differential Input Impedance 2.8/PGA M Ω Common-Mode Input Impedance PGA = 1 3.5 M Ω PGA = 2 3.5 M Ω PGA = 4 1.8 M Ω PGA = 8 0.9 M Ω SYSTEM PERFORMANCE Resolution and No Missing Codes DR = 00 12 12 BitsResolution and No Missing Codes DR = 01 14 14 Bits DR = 10 15 15 Bits DR = 11 16 16 Bits Data Rate DR = 00 180 240 308 SPSData Rate DR = 01 45 60 77 SPS DR = 10 22 30 39 SPS DR = 11 11 15 20 SPS Output Noise See Typical Characteristic Curves Integral Nonlinearity DR = 11, PGA = 1, End Point Fit(1) ±0.004 ±0.010 % of FSR(2) Offset Error PGA = 1 1.2 8 mVOffset Error PGA = 2 0.7 4 mV PGA = 4 0.5 2.5 mV PGA = 8 0.4 1.5 mV Offset Drift PGA = 1 1.2 µV/°COffset Drift PGA = 2 0.6 µV/°C PGA = 4 0.3 µV/°C PGA = 8 0.3 µV/°C Offset vs VDD PGA = 1 800 µV/VOffset vs VDD PGA = 2 400 µV/V PGA = 4 200 µV/V PGA = 8 150 µV/V Channel Offset Match Match between any two channels 30 µV Gain Error(3) 0.05 0.40 % PGA Gain Error Match(3) Match between any two PGA gains 0.02 0.10 % Gain Error Drift(3) 5 40 ppm/°C Gain vs VDD 80 ppm/V Channel Gain Match Match between any two channels 0.01 % Common-Mode Rejection At DC and PGA = 8 95 105 dBCommon-Mode Rejection At DC and PGA = 1 100 dB DIGITAL INPUT/OUTPUT Logic Level VIH 0.7 • VDD 6 V VIL GND − 0.5 0.3 • VDD V VOL IOL = 3mA GND 0.4 V Input Leakage IH VIH = 5.5V 10 µA IL VIL = GND −10 µA POWER-SUPPL Y REQUIREMENTS Power-Supply Voltage VDD 2.7 5.5 V Supply Current Power-Down 0.05 2 µASupply Current Active Mode 240 350 µA Power Dissipation VDD = 5.0V 1.2 1.75 mWPower Dissipation VDD = 3.0V 0.675 mW (1)99% of full-scale. (2)FSR = full-scale range = 2 × 2.048V/PGA = 4.096V/PGA. (3)Includes all errors from onboard PGA and reference.

/C0065/C0068/C0083/C0049/C0049/C0049/C0050 SBAS282D − JUNE 2003 − REVISED MARCH 2004 www.ti.com TYPICAL CHARACTERISTICS At TA = 25°C and VDD = 5V, unless otherwise noted.

/C0065/C0068/C0083/C0049/C0049/C0049/C0050 SBAS282D − JUNE 2003 − REVISED MARCH 2004 www.ti.com TYPICAL CHARACTERISTICS (continued) At TA = 25°C and VDD = 5V, unless otherwise noted.

At TA = 25°C and VDD = 5V, unless otherwise noted. surements to be obtained with a minimum of effort. scribed in detail in the sections that follow. reference; an external reference cannot be connected. not be measured directly or used by external circuitry. rate specifications for the onboard reference itself. the data rate, as shown in Table 1. Table 1. Minimum and Maximum Codes

minimum n-bit code is −1 × 2n−1. Table 2 shows the output codes for various input levels. not account for the gain and offset errors in the modulator. made. The self-calibration system cannot be deactivated. Characteristics include the effects of calibration. supply voltage and temperature. setting. See the Electrical Characteristics for details. be considered in high-accuracy applications. nevertheless contain noise and interference components. band just as with any other signal. response cannot completely replace an anti-aliasing filter. needed; in such instances, a simple RC filter will suffice. the input impedance of the ADS1112. (1)Differential input only; do not drive the ADS1112 inputs below −200mV. Table 2. Output Codes for Different Input Signals

/C0065/C0068/C0083/C0049/C0049/C0049/C0050 SBAS282D − JUNE 2003 − REVISED MARCH 2004 www.ti.com USING THE ADS1112 OPERATING MODES The ADS1112 operates in one of two modes: continuous- conversion or single-conversion. In continuous-conversion mode, the ADS1112 continu- ously performs conversions. Once a conversion has been completed, the ADS1112 places the result in the output register and immediately begins another conversion. In single-conversion mode, the ADS1112 waits until the ST/DRDY bit in the conversion register is set to 1. When this happens, the ADS1112 powers up and performs a single conversion. After the conversion completes, the ADS1112 places the result in the output register, resets the ST/DRDY bit to 0, and powers down. Writing a 1 to ST/DRDY while a conversion is in progress has no effect. When switched from continuous-conversion mode to single conversion mode, the ADS1112 completes the current conversion, resets the ST/DRDY bit to 0, and powers down. RESET AND POWER-UP When the ADS1112 powers up, it automatically performs a reset. As part of the reset process, the ADS1112 sets all of the bits in the configuration register to their default settings. The ADS1112 responds to the I2C General Call Reset command. When the ADS1112 receives a General Call Reset, it performs an internal reset, exactly as though it had just been powered on. I2C INTERFACE The ADS1112 communicates through an I 2C (inter-integrated circuit) interface. I2C is a two-wire open-drain interface supporting multiple devices and masters on a single bus. Devices on the I 2C bus only drive the bus lines LOW by connecting them to ground; they never drive the bus lines HIGH. Instead, the bus wires are pulled HIGH by pull-up resistors, so the bus wires are HIGH when no device is driving them LOW. This way, two devices cannot conflict; if two devices drive the bus simultaneously, there is no driver contention. Communication on the I 2C bus always takes place between two devices, one acting as the master and the other as the slave. Both masters and slaves can read and write, but slaves can only do so under the direction of the master. Some I 2C devices can act as masters or slaves, but the ADS1112 can only act as a slave device. An I2C bus consists of two lines, SDA and SCL. SDA carries data; SCL provides the clock. All data is transmitted across the I2C bus in groups of eight bits. To send a bit on the I2C bus, the SDA line is driven to the appropriate level while SCL is LOW (a LOW on SDA indicates the bit is zero; a HIGH indicates the bit is one). Once the SDA line has settled, the SCL line is brought HIGH, then LOW. This pulse on SCL clocks the SDA bit into the receiver’s shift register. The I 2C bus is bidirectional: the SDA line is used both for transmitting and receiving data. When a master reads from a slave, the slave drives the data line; when a master sends to a slave, the master drives the data line. The master always drives the clock line. The ADS1112 never drives SCL, because it cannot act as a master. On the ADS1112, SCL is an input only. Most of the time the bus is idle; no communication occurs place, and both lines are HIGH. When communication is taking place, the bus is active. Only master devices can start a communication and initiate a START condition on the bus. Normally, the data line is only allowed to change state while the clock line is LOW. If the data line changes state while the clock line is HIGH, it is either a START condition or its counterpart, a STOP condition. A START condition occurs when the clock line is HIGH and the data line goes from HIGH to LOW. A STOP condition occurs when the clock line is HIGH and the data line goes from LOW to HIGH. After the master issues a START condition, it sends a byte that indicates which slave device it wants to communicate with. This byte is called the address byte. Each device on an I 2C bus has a unique 7-bit address to which it responds. (Slaves can also have 10-bit addresses; see the I2C specification for details.) The master sends an address in the address byte, together with a bit that indicates whether it wishes to read from or write to the slave device. Every byte transmitted on the I2C bus, whether it is address or data, is acknowledged with an acknowledge bit. When a master has finished sending a byte (eight data bits) to a slave, it stops driving SDA and waits for the slave to acknowledge the byte. The slave acknowledges the byte by pulling SDA LOW. The master then sends a clock pulse to clock the acknowledge bit. Similarly, when a master has finished reading a byte, it pulls SDA LOW to acknowledge this to the slave. It then sends a clock pulse to clock the bit. (The master always drives the clock line.) A not-acknowledge is performed by simply leaving SDA HIGH during an acknowledge cycle. If a device is not present on the bus, and the master attempts to address it, it will receive a not-acknowledge because no device is present at that address to pull the line LOW.

indicating the intent of executing a read or write operation. Table 4. The state of pins A0 and A1 is sampled on prior to any activity on the interface. status of the address pins and reset the internal registers. Figure 1. I2C Timing Diagram Hold time after repeated START condition. After this period, the first clock is generated. Table 3. Timing Diagram Definitions

0 Float 1001001

1 Float 1001101

Table 4. Address Pins and Slave Address for the The I2C bus operates in one of three speed modes. compatible with all three modes. out of Hs mode with the next STOP condition. and remains zero until the first conversion is completed. The output register format is shown in Table 5. Table 5. Output Register

Table 6. Configuration Register being written to or read from. causes a conversion to start, and writing a 0 has no effect. register has been read before. register is new, and has not yet been read. register, and not to the data from the next read operation. Table 7. INP Bits. in continuous conversion mode. The default setting is 0. Table 8. INP Bits. Table 9. PGA Bits

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright  2004, Texas Instruments Incorporated