ADC701 BURR-BROWN
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 15
Technical content
® ADC701 SHC702 16-Bit 512kHz SAMPLING A/D CONVERTER SYSTEM
FEATURES
l CONVERSION RATE: to 512kHz Over Temp l NO MISSING CODES AT 16 BITS l SPURIOUS-FREE DYNAMIC RANGE: 107dB l LOW NONLINEARITY: ±0.0015% l SELECTABLE INPUT RANGES: ±5V, ±10V, 0 to +10V, 0 to +5V, –10V to 0 l LOW POWER DISSIPATION: 2.8W Typical Including Sample/Hold l METAL AND CERAMIC DIP PACKAGES
APPLICATIONS
l PROFESSIONAL AUDIO RECORDING l AUTOMATIC TEST EQUIPMENT l HIGH PERFORMANCE FFT SPECTRUM ANALYSIS l ULTRASOUND SIGNAL PROCESSING l HIGH SPEED DATA ACQUISITION l REPLACES DISCRETE MODULAR ADCs Timing and Control Logic Flash Encoder DAC ADC701 Switch Drive 1kΩ 1kΩ Input Scaling Network 10V Ref Buffer Output Buffer Input Analog Input PGA SHC702 Sample/Hold Command Convert Command Data Output Excellent linearity and stability are assured through use of a new ultra-precise monolithic D/A converter and a low-drift reference circuit. Custom monolithic op amps provide very high bandwidth and low noise in all sections of the analog signal path. Logic is CMOS/TTL compatible and is designed for maxi- mum flexibility.
DESCRIPTION
The ADC701 is a very high speed 16-bit analog-to- digital converter based on a three-step subranging architecture. Outstanding dynamic performance is achieved with the SHC702 companion sample/hold amplifier. Both devices use hybrid construction for applications where reliability, small size, and low power consumption are especially important. © 1988 Burr-Brown Corporation PDS-877D Printed in U.S.A. May, 1997 International Airport Industrial Park • Mailing Address: PO Box 11400, Tucson, AZ 85734 • Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 • Tel: (520) 746-1111 • Twx: 910-952-1111 Internet: http://www.burr-brown.com/ • FAXLine: (800) 548-6133 (US/Canada Only) • Cable: BBRCORP • Telex: 066-6491 • FAX: (520) 889-1510 • Immediate Product Info: (800) 548-6132
ELECTRICAL (ADC701 ONLY) At TA = +25°C, 500kHz sampling rate, ±VCC = ±15V, ±VDD1 = ±5V, +VDD2 = +5V, and five-minute warmup in a convection environment, unless otherwise noted. ADC701JH ADC701KH PARAMETER CONDITIONS MIN TYP MAX MIN TYP MAX UNITS RESOLUTION 16 * Bits INPUTS ANALOG Voltage Ranges Unipolar 0 to +5, 0 to +10, –10 to 0 V Bipolar ±5, ±10 V Resistance 0 to +5V Range 2.45 2.5 2.55 * * * k Ω 0 to +10V, –10 to 0, ±5V Ranges 4.9 5 5.1 * * * k Ω ±10V Range 9.8 10 10.2 * * * k Ω Capacitance All Ranges 5 * pF DIGITAL Logic Family TTL-Compatible CMOS Convert Command Start Conversion Rising Edge Pulse Width t = Conversion Period 50 t – 50 * * ns TRANSFER CHARACTERISTICS ACCURACY Gain Error(1) 0 to +10V Range ±0.03 ±0.1 * * % Power Supply Sensitivity of Gain All Ranges, All Supplies ±0.005 ±0.1 * * %/V Input Offset Error(1) 0 to +10V Range ±1 ±3* * m V Power Supply Sensitivity of Offset All Ranges, All Supplies ±0.006 ±0.1 * * %FSR/V Integral Linearity Error(2) ±0.002 ±0.003 ±0.0012 * %FSR (3) Differential Linearity Error(2) ±0.0006 ±0.0012 * * %FSR No Missing Codes Guaranteed Guaranteed Noise R SOURCE ≤ 50Ω 0.6 * LSB rms CONVERSION CHARACTERISTICS Sample Rate Unadjusted DC 512 * * kHz Conversion Time(4) Unadjusted 1.45 1.5 * * µs OUTPUTS DIGITAL Logic Family TTL-Compatible CMOS Data Coding Unipolar Ranges Straight Binary Bipolar Ranges Offset Binary Logic “0” Levels (VOL )I OL ≤ 3.2mA 0.1 0.4 * * V Logic “1” Levels (VOH )I OH ≤ 80µA 4 4.9 * * V Data Valid Setup Time Before Strobe Both Edges 28 37 * * ns INTERNAL REFERENCE Voltage R LOAD ≥ 5kΩ +9.995 +10.000 +10.005 * * * V Current Available to External Loads 2 5 * * mA POWER SUPPLY REQUIREMENTS Supply Voltages: +VCC Operating +14.25 +15 +15.75 * * * V Supply Currents: +ICC Operating 25 30 * * mA –ICC 33 45 * * mA +IDD1 45 55 * * mA –IDD1 37 50 * * mA +IDD2 133 150 * * mA Power Dissipation Nominal Voltages 1.95 2.3 * * W PERFORMANCE OVER TEMPERATURE Specification Temperature Range T A Min to TA Max +15 +55 0 +70 °C Gain Error All Ranges ±10 ±15 * * ppm/ °C Input Offset Error All Unipolar Ranges ±1 ±5 * * ppm FSR/ °C All Bipolar Ranges ±1 ±5 * * ppm FSR/ °C Integral Linearity Error(2) ±0.2 * ±0.5 ppm/ °C Differential Linearity Error(2) ±0.05 * ±0.3 ppm/ °C No Missing Codes Typical Guaranteed Reference Output Drift ±3 * ppm/ °C Drift of Conversion Time Unadjusted +3 +4 * * ns/ °C Sample Rate Unadjusted DC 512 * * kHz * Same specifications as ADC701JH.
ELECTRICAL (SHC702 ONLY) At TA = +25°C, 500kHz sampling rate, ±VCC = ±15V, +VDD1 = +5V, and five-minute warmup in a convection environment, unless otherwise noted. SHC702JM PARAMETER CONDITIONS MIN TYP MAX UNITS INPUTS (Without Input Buffer) ANALOG Voltage Range ±10.25 ±11 V Resistance 0.98 1 1.02 k Ω Capacitance 3p F DIGITAL Logic Family LSTTL Input Loading 2 LSTTL Loads TRANSFER CHARACTERISTICS ACCURACY Gain R SOURCE = 0Ω –1 V/V Gain Error R SOURCE = 0Ω± 0.02 ±0.1 % Linearity Error Sample Mode ±0.0003 %FSR Offset Error Sample Mode ±0.5 ±3m V Charge Offset (Pedestal) Error Sample/Hold Mode, R SOURCE ≤ 50Ω± 0.5 ±5m V Droop Rate Hold Mode ±0.2 ±2 µV/µs Dynamic Nonlinearity Sample/Hold Mode ±0.0005 %FSR Power Supply Sensitivity Offset Plus Charge Offset, All Supplies ±0.003 %FSR/V DYNAMIC CHARACTERISTICS Acquisition Time 10V Step to ±150µV 600 ns 5V Step to ±150µV 500 ns Sample-to-Hold Settling Time(5) to ±150µV 120 ns Aperture Delay Time 20 ns Aperture Uncertainty (Jitter) 10 25 ps rms Slew Rate 150 V/ µs Small Signal Bandwidth V IN = ±1V 3.1 MHz Full-Power Bandwidth V IN = ±10V 2 MHz Feedthrough Rejection Hold Mode, 10Vp-p Square Wave Input 0.001 % OUTPUT Voltage Range R LOAD ≥ 1kΩ± 10.25 ±11 V Output Current ±40 mA Short Circuit Protection R LOAD = 0Ω Indefinite Output Impedance DC 0.01 0.1 Ω INPUT BUFFER CHARACTERISTICS INPUT Impedance 1013 3 Ω pF Bias Current V IN = ±10V ±2 ±15 pA Offset Voltage R SOURCE ≤ 10kΩ± 0.3 ±1.5 mV Voltage Range ±10.25 ±11 V DYNAMIC CHARACTERISTICS Slew Rate 20 35 V/ µs Full-Power Bandwidth V IN = ±10V 570 kHz Settling Time 10V Step to ±150µV 1.7 µs OUTPUT Output Current ±15 ±20 mA Short Circuit Protection R LOAD = 0Ω Indefinite POWER SUPPLY REQUIREMENTS Voltage: +VCC Operating +13.5 +15 +16.5 V Current: +ICC Operating 33 40 mA –ICC 18 25 mA +IDD1 51 0 m A Power Dissipation Nominal Voltages 790 950 mW PERFORMANCE OVER TEMPERATURE Specification Temperature Range T A Min to TA Max 0 +70 °C Sample/Hold Gain Error R SOURCE = 0Ω± 1 ±5 ppm/ °C Sample/Hold Offset Error R SOURCE ≤ 50Ω± 10 ±30 µV/°C Sample/Hold Charge Offset Error R SOURCE ≤ 50Ω± 10 ±80 µV/°C Droop Rate ±50 µV/µs Buffer Offset Error R SOURCE ≤ 10kΩ± 3 ±15 µV/°C NOTES: (1) Adjustable to zero. Tested and guaranteed for 0 to +10V and ±10V ranges only. (2) Peak-to-peak based on 99.9% of all codes. (3) FSR means full- scale range and depends on the input range selected. (4) ADC conversion time is defined as the time that the Sample/Hold must remain in the Hold mode; i.e., the duration of the Sample/Hold command. This time must be added to the Sample/Hold acqusition time to obtain the total system throughput time. (5) Given for reference only — this time overlaps with the ADC701 conversion time and does not affect system throughput rate.
PIN NO. DESCRIPTION 40 –V DD1 (–5V) Analog
39 Common (Analog)
38 +V DD1 (+5V) Analog
37 Reference (Gain) Adjust
(2)
35 Common (Reference)
34 DNC
33 Common (Analog)
(2)
31 Input D (1)
30 Input C (1)
29 Common (Signal)
28 Input B
(1)
27 Input A (1)
26 –V CC (–15V) Analog
25 Common (Power)
24 +V CC (+15V) Analog
23 DNC (4)
22 Offset Adjust
21 Offset Adjust
PIN NO. DESCRIPTION
1 Bit 1/9 (Bit 1 = MSB)
2 Bit 2/10
3 Bit 3/11
4 Bit 4/12
5 Bit 5/13
6 Bit 6/14
7 Bit 7/15
8 Bit 8/16
9 Clip Detect Output
DD2 (+5V) Digital
11 Common (Digital)
12 Data Strobe
13 High/Low Byte Select
14 Convert Command
15 Sample/Hold Control
(3)
16 Common (Digital)
17 Common (Digital)
18 Clock Adjust
19 Common (Digital)
DD2 (+5V) Digital PARAMETER CONDITIONS MIN TYP MAX UNITS Sample Rate Unadjusted DC 512 kHz Dynamic Nonlinearity ±0.002 %FSR Total Harmonic Distortion (THD) f IN = 20kHz (–0.3dB) –103 dB fIN = 199kHz (–0.2dB) –82 dB Spurious-Free Dynamic Range (SFDR) f IN = 20kHz (–0.3dB) 107 dB fIN = 199kHz (–12dB) 94 dB Two-Tone Intermodulation Distortion (IMD) f1 = 195kHz (–6.5dB), f2 = 200kHz (–6.5dB) –81 dBC f1 = 195kHz (–12.5dB), fF2 = 200kHz (–12.5dB) –86 dBC Signal-to-Noise Ratio (SNR) f IN = 5kHz (–0.5dB) 93 dB Total Power Dissipation Operating 2.8 3.25 W SPECIFICATIONS ELECTRICAL (COMBINED ADC701/SHC702) At TA= +25°C, 500kHz sampling rate, ±VCC = ±15V, ±VDD1 = ±5V, +VDD2 = +5V, and five-minute warmup in a convection environment,±5V input range, unless otherwise noted. ADC701 PIN ASSIGNMENTS ADC701 ORDERING INFORMATION ADC701 ABSOLUTE MAXIMUM RATINGS Stresses above these ratings may permanently damage the device. ADC701 H Basic Model Number Performance Grade Code K: 0°C to +70°C Ambient Temperature J: +15°C to +55°C Ambient Temperature Package Code H: Metal and Ceramic NOTES: (1) Refer to Input Connection Table. (2) Reference Input is normally connected to Reference Output, unless an external 10V reference is used. (3) Sample/Hold Control goes high to activate Hold mode. (4) DNC = Do Not Connect. PACKAGING INFORMATION PACKAGE DRAWING PRODUCT PACKAGE NUMBER (1) ADC701JH Metal and Ceramic 230 ADC701KH Metal and Ceramic 230 NOTE: (1) For detailed drawing and dimension table, please see end of data sheet, or Appendix C of Burr-Brown IC Data Book.
PIN NO. DESCRIPTION
1 Sample/Hold Output
2N C (3) 3N C 4N C 5N C 6N C 7N C 8N C 9+ V DD1 (+5V) Analog
10 Common (Digital)
11 Hold Input
(1)
12 Hold Input (1)
INPUT LEVEL 0–10V RANGE ±10V RANGE ±5V RANGE (1 = Logic High) CLIP (Exact Center of Code) (1LSB ≈153µV) (1LSB ≈05µV (1LSB ≈153µV) MSB LSB DETECT Underrange < –76 µV < –10.000153V < –5.000076V 0000 0000 0000 0000 1 –FS 0V –10V –5V 0000 0000 0000 0000 0 –FS + 1LSB +153 µV –9.999695V –4.999847V 0000 0000 0000 0001 0 –3/4FS +1.25V –7.5V –3.75V 0010 0000 0000 0000 0 –1/2FS +2.5V –5V –2.5V 0100 0000 0000 0000 0 –1/4FS +3.75V –2.5V –1.25V 0110 0000 0000 0000 0 –1LSB +4.999847V –305 µV –153 µV 0111 1111 1111 1111 0 Mid-Scale +5V 0V 0V 1000 0000 0000 0000 0 +1LSB +5.000153V +305 µV +153 µV 1000 0000 0000 0001 0 +1/4FS +6.25V +2.5V +1.25V 1010 0000 0000 0000 0 +1/2FS +7.5V +5V +2.5V 1100 0000 0000 0000 0 +3/4FS +8.75V +7.5V +3.75V 1110 0000 0000 0000 0 +FS –2LSB +9.999695V +9.99939V +4.999695V 1111 1111 1111 1110 0 +FS – 1LSB +9.999847V +9.999695V +4.999847V 1111 1111 1111 1111 0 Overrange > +9.999924V > +9.999847V > +4.999924V 1111 1111 1111 1111 1 NOMINAL INPUT VOLTAGE TO ADC701 (Multiply by –1 for SHC702 Input Voltage) SHC702 ORDERING INFORMATIONSHC702 PIN ASSIGNMENTS SHC702 J M Basic Model Number Performance Grade Code J: 0°C to +70°C Ambient Temperature Package Code M: Metal PIN NO. DESCRIPTION 24 +V CC (+15V) Analog
23 Common (Power)
22 –V CC (–15V) Analog
21 Common (Analog)
17 Buffer Amp Input
(2) 16 NC
15 Common (Signal)
14 Buffer Amp Output
13 Analog Input
NOTES: (1) Hold mode is activated only when pin 12 is low and pin 11 is high. For normal use with ADC701, pin 12 is grounded and pin 11 is connected to ADC701 Sample/Hold control (ADC701 pin 15). (2) If the buffer amp is not used, pin 17 should be grounded. (3) NC = No Internal Connection. PACKAGING INFORMATION PACKAGE DRAWING PRODUCT PACKAGE NUMBER (1) SHC702JM 24-Pin 037 NOTE: (1) For detailed drawing and dimension table, please see end of data sheet, or Appendix C of Burr-Brown IC Data Book. SHC702 ABSOLUTE MAXIMUM RATINGS Stresses above these ratings may permanently damage the device. The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes no responsibility for the use of this information, and all use of such information shall be entirely at the user's own risk. Prices and specifications are subject to change without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant any BURR-BROWN product for use in life support devices and/or systems.
TYPICAL DYNAMIC PERFORMANCE (ADC701/SHC702) (1) Frequency (kHz) Amplitude (dB) –20 –40 –60 –80 –100 –120 –140 0 250 FULL-SCALE SINEWAVE RESPONSE, f = 100kHz 50 100 150 200 IN Input Frequency 19.9890136719 kHz Fundamental –0.3 dB 4th Harmonic –115.6 dB 2nd Harmonic –107.5 dB 5th Harmonic –111.2 dB 3rd Harmonic –111.5 dB 6th Harmonic –124.5 dB V 3 V V V 9 V V V V V V Input Frequency 100.982666016 kHz Fundamental –0.5 dB 4th Harmonic –102.5 dB 2nd Harmonic –89.1 dB 5th Harmonic –110.2 dB 3rd Harmonic –90.5 dB 6th Harmonic –106.8 dB Frequency (kHz) Amplitude (dB) –20 –40 –60 –80 –100 –120 –140 0 250 FULL-SCALE SINEWAVE RESPONSE, f = 200kHz 50 100 150 200 IN Frequency (kHz) Amplitude (dB) –20 –40 –60 –80 –100 –120 –140 0 250 50 100 150 200 TWO-TONE INTERMODULATION RESPONSE, = 195kHz and 200kHzINf Frequency 1 194.976806641 kHz Frequency 2 199.981689453 kHz f1 –6.8dB 3 > f 1 +2f2 –96.0dB f2 –6.3dB 4 > 2f 1 +f2 –96.8dB 1 > f1 +f2 –87.7dB 5 > f 1 –2f2 –104.9dB 2 > f1 –f2 –88.8dB 6 > 2f 1 –f2 –109.0dB NOTE: (1) For figures above, sampling rate = 500.0000000000kHz. 16,384 point FFT, non-windowed. Noise floor limited by synthesized generators. V V V V 3 V V 7 V V Input Frequency 199.005126953 kHz Fundamental –0.7dB 4th Harmonic –111.5dB 2nd Harmonic –81.4dB 5th Harmonic –97.0dB 3rd Harmonic –89.4dB 6th Harmonic –112.5dB Frequency (kHz) Amplitude (dB) –20 –40 –60 –80 –100 –120 –140 0 250 FULL-SCALE SINEWAVE RESPONSE, f IN = 20kHz 50 100 150 200 Codes DNL (LSB) 0 65535 DIFFERENTIAL NONLINEARITY OF ALL CODES,
19.6 MILLION SAMPLES
for simplified block diagrams of the system. mode) and the fully open (hold mode) states of the switch. FIGURE 2. Simplified Block Diagram of the ADC701. FIGURE 1. Simplified Block Diagram of the SHC702.
7 Bit
At the beginning of each conversion, the DAC is reset to mid-scale so that its output current is exactly 1mA. This 1mA is subtracted from the input signal current. The differ- ence current flows through Rf and appears as an error voltage at the output of A1. During the first pass, the programmable gain amplifier (PGA) is set to unity gain, which matches the error voltage range to the input range of the flash ADC. The error signal is digitized to 7-bit resolution by the flash ADC, creating a coarse approximation of the digital output value, which is then applied to the DAC. Since the DAC output is now approximately equal to the input signal current, the remaining difference current flow- ing through Rf is small—ideally less than 1/128 of full scale, which is due to the built-in quantizing uncertainty of the 7- bit flash ADC. However, other sources of error (e.g., integral and differential nonlinearity of the flash ADC, gain and offset of the PGA, settling and noise errors throughout the signal path) cause the possible error range to be significantly greater. In fact, the ADC701 is designed to handle remainder signals up to 1/32 of full scale, which is four times the “ideal” value. Therefore, the PGA is set during the second pass to a gain of 32, allowing the small remainder signal to match the full range of the flash ADC. This is again digitized to 7-bit resolution and added to the previous result to create the “medium” approximation of the input signal. Because the full-scale range of the flash represents 1/32 of the input signal’s full range, the 7-bit flash output is shifted right by 5 bits before being added to the original 7-bit “coarse” result, creating a 12-bit word. There is an overlap of two bits because the two least significant bits of the first-pass result correspond to the two most significant bits of the second- pass result. This overlap in the adder is called “digital error correction”—the mechanism that allows nonideal remain- ders from the first pass to be corrected in the second pass. The 12-bit approximation is applied once again to the DAC, causing the remaining difference current to become yet smaller. For the third pass, the PGA’s gain is increased by another factor of 32, and the remainder is again digitized by the flash ADC. At this point in the conversion, all of the necessary data has been latched and it is no longer necessary to hold the analog signals from the sample/hold or the DAC. From a systems perspective, the conversion is now complete because the sample/hold is released to begin acquiring the next input sample and the DAC is reset to mid-scale for the next conversion. Meanwhile, the final result from the flash is added to the previous 12-bit result. Again there is a two-bit overlap to allow for error correction. The adder output is monitored to prevent a digital “rollover” condition, so that the ADC clips properly at the signal extremes. The upper sixteen bits of the final adder result are stored in the ADC’s output register, ready to be presented in byte-sequential form at the eight output data lines. The overrange or “clip” condition can also be detected externally by monitoring pin 9. Refer to the section on ADC701 Digital I/O for further detail. INSTALLATION AND OPERATING INSTRUCTIONS The ADC701/SHC702 combination is designed to be easy to use in a wide variety of applications, without sacrificing flexibility of the analog and digital interface. SHC702 INTERFACE The connection diagram (Figure 3) shows the basic hookup. At the SHC702 input, the user may opt to connect the built- in FET buffer amplifier. The buffer is most useful in multi- channel applications where the signal bandwidth is less than 100kHz. In those applications, it serves to isolate the multi- plexer output from the 1kΩ input impedance of the sample/ hold. For higher frequency applications and for any system that does not require the very high impedance, the best results (lowest noise and distortion) will be achieved by driving the SHC702’s analog input directly. If the buffer is not used, its input should be grounded to avoid random noise pickup and saturation of the buffer op amp. Only two connections are required between the SHC702 and the ADC701: SHC702 analog output to ADC701 input(s) and the digital Hold Command from the ADC701 to the SHC702. As always, it is best to avoid routing these analog and digital lines along parallel traces. Although the place- ment of the SHC702 relative to the ADC is not extremely critical, one good approach is to mount the SHC along one end of the ADC package as shown in Figure 4. This mini- mizes the length of the interconnections and keeps the digital lines well away from sensitive analog signals. ADC701 INPUT CONNECTIONS The ADC input network has four separate terminals, allow- ing many different input ranges. These should be connected as indicated in Table I. Most users will take advantage of the ADC701’s built-in reference circuit, which has very low noise and excellent temperature stability. To use the internal reference, it is only necessary to connect pin 36 (Reference Output) to pin 32 (Reference Input). To use an external 10V reference (to cause the ADC gain to track a system refer- ence, for example), pin 36 is left unconnected and the external reference is applied to pin 32. If required, the ADC701 will typically accommodate a five to ten percent variation in the 10V reference. External references should have very low noise to avoid degrading the excellent signal- to-noise ratio (SNR) of the ADC701. INPUT RANGE CONNECT V IN TO CONNECT Ref In TO 0 to +10V Input A and Input D — ±10V Input A Input D ±5V Input A and Input B Input D –10V to 0 Input A and Input B Input C and Input D 0 to +5V Input B and Input C — TABLE I. ADC701 Input Connection Table.
FIGURE 3. ADC701/SHC702 Connection Diagram.
OFFSET, GAIN AND CONVERSION SPEED ADJUSTMENTS (OPTIONAL) Adjustment of the reference voltage is the most straightfor- ward way to adjust the ADC gain. For the internal reference, this is accomplished by connecting a 20kΩ potentiometer as shown in Figure 3. This will provide a gain trim range of about ±3%. It is also possible to use external series or parallel resistance in the input network, but that is more cumbersome and usually will degrade the gain stability over temperature due to tempco (temperature coefficient) mis- matches among the resistors. ADC offset may be adjusted by connecting a 500kΩ poten- tiometer to pins 21 and 22, with the wiper connected through a series 30kΩ resistor to ground as shown in Figure 3. This will provide an offset trim range of approximately ±0.25% FSR. For a larger trim range of offset or gain, it is recommended that trims be accomplished elsewhere in the system. The Clock Adjust input (pin 18) is intended primarily for small adjustments of the conversion time. However, this will rarely be necessary because the ADC701 is guaranteed to convert up to 512kHz over the specified temperature range without external clock adjustment. POWER AND GROUND CONNECTIONS Experience with testing and applying the ADC701 shows that it will perform well in most board layouts, provided that appropriate care is taken with grounding and bypassing. Power supplies may be shared between the ADC701, SHC702 and other analog circuitry without difficulty. It is recom- mended that each power pin be locally bypassed to the ground plane with a high quality tantalum capacitor of at least 1µF. If at all possible, power should be derived from well-regulated linear supplies—switching power supplies will require much more effort for proper decoupling and are not recommended for this or any high performance wide- band analog system. The +5V Digital supply pins, though not as sensitive to noise as the +5V Analog pin, should nonetheless be kept as quiet as possible. If the system digital supply is noisy, then it is best to use the system +5V analog supply for all of the +5V connections on the ADC701 and SHC702 rather than trying to separate them. If only one +5V supply is available and it is shared with other system logic, then extra bypassing and/or supply filtering may be required. The –5V supply will operate with any voltage between – 4.75 and –6V. If –5V is not available from the system supplies, then an industry-standard 7905 regulator may be used to derive –5V from the –15V supply. All ground pins on both the ADC701 and the SHC702 should be connected directly to a common ground plane. This is true for both analog and digital grounds. However, it is also helpful to recognize where the digital ground currents flow in the system, and to provide PC board return paths for potentially troublesome digital currents in addition to the ground plane connections. For example, the ADC701 output data lines will sink current (statically and/or dynami- cally) when in the low state. This current comes from the power supply that runs the interface logic, and so must return to that supply’s ground. If the ground termination is placed such that this digital current will flow away from the ADC701, then the existing ground plane will suffice to carry the current. On the other hand, if the ground termination must be placed such that the digital current flows across the ADC or SHC layout, then it would be advisable to break the analog ground plane under the package (to stop the flow of current across the package) and to provide a separate trace (several centimeters wide) on another PC board layer to carry the digital return current from pins 11 and 19 to the termination point. If the ADC701 must interface into a fairly noisy digital environment, then another approach is to keep the first layer of latches and/or buffers connected to the ADC701 power and ground planes, so that the ADC itself is connected to “quiet” circuits with short return paths. This transfers the interface problem to the outputs of the latches, where it can be managed with less impact on the analog components. PHYSICAL INSTALLATION The packages may be soldered directly into a PC board or mounted in low-profile machined pin sockets with good results. Use of tall (long lead length) sockets, adapters or headers is not recommended unless a local ground plane and bypass capacitors can be mounted directly under the pack- ages. In a room-temperature environment or inside an enclosure with moderate airflow, the ADC701 and SHC702 normally do not require heat-sinking. However, to keep the devices running as cool as possible, it is helpful to install a thin heat- transfer plate under the packages to conduct heat into the ground plane. The plate may be made from metal (copper, aluminum or steel) or from a special heat-conductive mate- rial such as Sil-Pad(1). The Sil-Pad material has the advan- tage of being electrically insulating and somewhat pliable, so that it will tend to distribute pressure evenly and conform to the package—an advantage in systems where the board may be flexed or subjected to vibration. PC BOARD LAYOUT An optimized layout has been designed for the DEM- ADC701-E demonstration fixture. For information concern- ing the demo board and the layout, contact your local sales representative.
NOTES: (1) Setup Time 28ns min, 37ns typ. (2) Hold Time 30ns min, 73ns typ. (3) High Byte refers to ADC bits 1 - 8, the most significant 8 bits. Also, the Clip Detect signal on pin 9 is valid simultaneously with High Byte. (4) Low Byte refers to ADC bits 9 - 16, the least significant bits. command output to a logic high state (Hold mode).
- Strobed Output—This will usually be the easiest and
- Polled output—With this method, data strobes will occur
as described above, but they are ignored by the user. clock edge for the second flip-flop IC. switching of the 16 output bits will be achieved. which indicates an ADC overrange or underrange condition. tions, and indicates a clip condition by rising to a logic 1. FIGURE 4. ADC701 Interface Timing Diagram.
The latched version of Clip Detect may be used to generate an interrupt to the user’s system computer, which would then launch a service routine to generate the appropriate alarms or corrective action. Another possible application would be to stretch the pulse using a monostable so that it would be easily visible when driving an LED warning lamp. In some systems, it may be desirable to provide separate latched outputs for Underrange and Overrange. These con- ditions may be separately detected by using simple logic to implement the boolean equations: Underrange = Clip Detect AND Anybit Overrange = Clip Detect AND Anybit where “Anybit” is any one of the data output bits. The Underrange and Overrange signals would then be latched into two separate flip-flops. A simple solution using a single ’74 dual flip-flop and a single ’00 quad NAND provides enough logic to implement the logic equations, with a spare NAND gate left over to use for creating the inverted Data Strobe signal. USING THE ADC701 AT MAXIMUM CONVERSION RATES The ADC701 is guaranteed to accept Convert commands at a rate of DC to 512kHz over the specified operating tem- perature range. At a conversion rate of 500kHz, the total throughput time of 2µs allows for the 1.5µs ADC conversion time plus 500ns for the digital output timing and sample/ hold acquisition time. If the user tries to exceed the maximum conversion rate by a large amount, the Convert Command of conversion N+1 will occur before the Data Strobe has fallen from conversion N. In such a situation, the ADC701 will simply ignore every other Convert command so the actual conversion rate will become half of the Convert command rate. Otherwise, the conversion will proceed normally. Note that the ADC timing slows down at high temperatures, so the frequency at which this occurs will vary with temperature—although it is still guaranteed to be greater than 512kHz over the specified temperature range. Another consideration for operation at very high rates is that the sample/hold acquisition time becomes shorter as the conversion rate is increased. Users will note that the avail- able acquisition time becomes less than 550ns at rates above 500kHz, which is less than the typical SHC702 acquisition time for a 10V step to 150µV accuracy. However, the signal degradation is gradual as the acquisition time is shortened— even at 512kHz, there is enough time to acquire a 5V step to better than 500µV. Also, most signal processing environ- ments do not contain full-power signals at the Nyquist frequency, but rather show a rolloff of signal power at high frequencies. If the ability to acquire extremely large input changes at extremely high conversion rates is of paramount importance, the user may elect to use a Burr-Brown model SHC803 sample/hold instead—it is pin compatible with the SHC702 and provides much faster acquisition time at the expense of some extra noise and higher distortion at low input frequencies. TESTING THE ADC701/SHC702 The ADC701 and SHC702 together form a very high perfor- mance converter system and careful attention to test tech- niques is necessary to achieve accurate results. Spectral analysis by application of a Fast Fourier Transform (FFT) to the ADC digital output is the best method of examining total system performance. Attempts to evaluate the system by analog reconstruction through a D/A converter will usually prove unsatisfactory; assuming that the static and dynamic distortions of the D/A can be brought below the required level (–110dB), the performance will still be beyond the range of presently available spectrum analyzers. Even when the analysis is done using FFT techniques, several key issues must be addressed. First, the parameters of the FFT need to be adequate to perform the analysis and extract meaningful data. Second, the proper selection of test frequencies is critical for good results. Third, the limitations of commercial signal generators must be considered. These three points are addressed in later sections. Finally, the test board layout must follow the recommendations discussed on pages 8 through 10. IMD is referred to the larger of the test signals f 1 or f2— not to the total signal power, which would result in a number approximately 6dB “better. ” The zero frequency bin (DC) is not included in these calculations—it represents total offset of the ADC, SHC and test equipment and is of little impor- tance in dynamic signal processing applications. 10 log 10 log 10 log 10 log DYNAMIC PERFORMANCE DEFINITIONS 1. Total Harmonic Distortion (THD): Harmonic Power (first 9 harmonics) Sinewave Signal Power 2. Signal-to-Noise Ratio (SNR): Sinewave Signal Power Noise Power 3. Intermodulation Distortion (IMD): IMD Product Power (RMS sum; to 3rd-order) Sinewave Signal Power 4. Spurious-Free Dynamic Range (SFDR): Power of Peak Spurious Component Sinewave Signal Power
Accurate FFT analysis of 16-bit systems requires adequate computing hardware and software. The FFT length (number of points) should be relatively large—at least 4K and prefer- ably 16K or larger. There are several reasons for this: 1. The converter itself has 64K codes. Ideally, the test would guarantee that all codes are tested at least once. Practically speaking, however, that would require im- mensely long FFTs (>>64K points) or averaging of a large number of smaller FFTs. By using an FFT length of 4K or greater and proper selection of the test frequencies, a very good statistical picture of the ADC performance will be obtained which shows the effect of any defects in the transfer function. 2. The noise floor of the output spectrum is not low enough if less than 4K points are taken. Shorter FFTs have fewer bins to cover the output spectrum, so a larger fraction of the total system noise appears in each bin. Although the SNR of the ADC701/SCH702 system is in the range of –93dB, the noise level of the available generators may increase the total measured noise power to –80dB. Every doubling of the FFT length will spread the noise power among twice as many bins, resulting in a 3dB reduction of the spectral noise floor. In order to resolve spurious components that are at the level of –110dB, an average noise floor of less than –113dB would be barely ad- equate. This requires at least 2048 bins in the output half-spectrum, corresponding to a 4K-point FFT. Even at this level, it will be difficult or impossible to separate higher order harmonics in the ADC701 response from the average noise level, indicating that longer FFTs are desirable. 3. Following the guidelines for test frequency selection which are outlined in the next section, it becomes clear that longer FFTs allow a much wider choice of test frequencies without concern for sophisticated data win- dowing or code coverage problems. Besides the consideration of FFT length, it is important to realize that the FFT calculations must be performed with high-precision arithmetic. The use of 32-bit fixed or floating point calculations will generally be inadequate because the noise floor due to calculation errors alone will interfere with the ADC performance data. Unfortunately, this considera- tion precludes the use of most DSP accelerator boards and similar hardware. In order to preserve the full dynamic range of the ADC output, it is best to use standard 64- or 80-bit arithmetic. To avoid excessively long calculation times, the FFT algorithm should be written in an efficiently compiled language and make use of techniques such as trigonometric look-up tables in software and dedicated floating-point coprocessors in hardware. There are several commercial software packages available from Burr-Brown and others that meet these requirements. SELECTION OF TEST FREQUENCIES The FFT (and any similar DSP operation) treats the total time-domain record length as one cycle of an infinitely long periodic signal. Therefore, if the end of the sampled record does not match up smoothly with the beginning, the output spectrum will contain serious errors known as leakage or truncation error(2). This well-known problem is usually handled by applying a windowing function to the time- domain samples, suppressing the worst effects of the mis- match. However, the most often used windows such as Hanning, Hamming, raised cosine, etc., are completely inad- equate for 16-bit ADC testing. More sophisticated functions such as the four-sample Blackman-Harris window(3) will provide much better results, although there still will be obvious spreading of the spectral lines. The most successful approach is to eliminate the need for windowing by properly selecting the test signal frequency (or frequencies) in relation to the ADC sampling frequency(4). If the time sample contains exactly an integer number of cycles, then there is no mismatch or truncation error. An- other point to consider is that the sampling frequency should not be an exact integer multiple of the signal frequency, which would tend to reduce the number of different ADC codes that are tested and also tend to artificially concentrate quantization error in the harmonics of the test signal. Both of these criteria are met by choosing an FFT length which is a power of two (the most standard and fastest to compute) and choosing a test frequency which causes an exact odd integer number of cycles to appear in the time record. In software, this selection can be accomplished very easily: 1. Determine the desired sampling frequency fS. 2. Determine the desired input signal frequency fAPPROX. 3. Determine the FFT length N, which should be a power of 2 (e.g., 4096 or 16384). 4. Divide fAPPROX by fS, multiply the quotient by N, and round the result to the nearest odd integer. This is M, the number of cycles in the time record. 5. Multiply M by fS and divide by N to obtain the exact input signal frequency fACTUAL . SIGNAL GENERATOR CONSIDERATIONS To suppress leakage effects, the calculated ratio of fS to fACTUAL must be precisely maintained during the test. This requirement is met easily by the use of synthesized signal generators whose reference oscillators can be locked to- gether. Other possible approaches include external phase locking of non-synthesized generators and direct digital synthesis techniques. If it is not possible to use phase-locked signals, then a Blackman-Harris window may be used as mentioned previously.
noise (jitter) will act as another source of SNR degradation. to the input, resulting in typical SNR performance of –93dB. rate, using 16K samples for the FFT analysis. NOTES: (1) Setup Time 28ns min, 37ns typ. (2) Hold Time 30ns min, 73ns typ. (3) High Byte refers to ADC bits 1 - 8, the most significant 8 bits. Also, the Clip Detect signal on pin 9 is valid simultaneously with High Byte. (4) Low Byte refers to ADC bits 9 - 16, the least significant bits. FIGURE 5. FFT Test Configuration for Single-Tone Testing.
appearance of the noise floor. point histogram taken at an input frequency of 1kHz.
- Available from Bergquist, 5300 Edina Industrial Blvd., Minneapolis, MN 55435
- Brigham, E. Oran, The Fast Fourier Transform, Englewood Cliffs, N.J.: Prentice-
- Harris, Fredric J., “On the Use of Windows for Harmonic Analysis with the Discrete
- Halbert, Joel M. and Belcher, R. Allan, “Selection of Test Signals for DSP-Based
Testing of Digital Audio Systems” , Journal of the Audio Engineering Society, Vol.
- “Dynamic Tests for A/D Converter Performance”, Application Bulletin AB-133,
Burr-Brown Corporation, Tucson, AZ, 1985. FIGURE 6. FFT Test Configuration for Two-Tone (Intermodulation) Testing.