AC0402BRNPO5BN YAGEO
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 24
Technical content
Product Specification – March 31, 2017, V.6 DATA SHEET SURFACE MOUNT MULTILAYER CERAMIC CAPACITORS Automotive grade NP0/X7R
6.3 V TO 630 V
0.47 pF to 2.2 µF RoHS compliant & Halogen Free
www.yageo.com Mar. 31, 2017 V.6 Surface-Mount Ceramic Multilayer Capacitors Product specification ORDERING INFORMATION - GLOBAL PART NUMBER All part numbers are identified by the series, size, tolerance, TC material, packing style, voltage, process code, termination and capacitance value. GLOBAL PART NUMBER AC XXXX X X XXX X B X XXX (1) SIZE – INCH BASED (METRIC) 0402 (1005) / 0603 (1608) / 0805 (2012) / 1206 (3216)/ 1210 (3225) / 0508 (1220) / 0612 (1632) (2) TOLERANCE B = ± 0.1 pF C = ± 0.25 pF D = ± 0.5 pF F = ± 1% G = ± 2% J = ± 5% K = ± 10% M = ± 20% (3) PACKING STYLE R = Paper/PE taping reel; Reel 7 inch K = Blister taping reel; Reel 7 inch P = Paper/PE taping reel; Reel 13 inch F = Blister taping reel; Reel 13 inch (4) TC MATERIAL NPO X7R (5) RATED VOLTAGE 5 = 6.3 V 6 = 10 V 7 = 16 V 8 = 25 V 9 = 50 V 0 = 100 V A = 200 V Y = 250 V B = 500 V Z = 630 V (6) PROCESS N = NP0 B = Class 2 MLCC (7) CAPACITANCE VALUE 2 significant digits+number of zeros The 3rd digit signifies the multiplying factor, and letter R is decimal point Example: 121 = 12 x 101 = 120 pF SCOPE This specification describes Automotive grade NP0/X7R series chip capacitors with lead -free terminations and used for automotive equipment s.
APPLICATIONS
All general purpose applications Entertainment applications Comfort / security applications Information applications
FEATURES
AEC-Q200 qualified MSL class: MSL 1 AC series soldering is compliant with J -STD-020D Halogen free epoxy RoHS compliant Reduce environmentally hazardous waste High component and equipment reliability Save PCB space The capacitors are 100% performed by automatic optical inspection prior to taping.
www.yageo.com Mar. 31, 2017 V.6 Surface-Mount Ceramic Multilayer Capacitors Product specification CONSTRUCTION The capacitor consists of a rectangular block of ceramic dielectric in which a number of interleaved metal electrodes are contained. This structure gives rise to a high capacitance per unit volume. The inner electrodes are connected to the two end terminations and finally covered with a layer of plated tin ( Matte Sn). The terminations are lead - free. A cross section of the structure is shown in Fig.1. Fig. 1 Surface mounted multilayer ceramic capacitor construction TYPE L1 (mm) W (mm) T (MM) L2 / L3 (mm) L4 (mm) min. max. min. 0402 1.0 ± 0.05 0.5 ± 0.05 Refer to table 3 to 12 0.15 0.30 0.40 Table 1 For outlines see fig. 2 DIMENSION OOUUTTLLIINNEESS For dimension see Table 1 Fig. 2 Surface mounted multilayer ceramic capacitor dimension OOUUTTLLIINNEESS For dimensions see Table 2 Fig. 3 Surface mounted multilayer ceramic capacitor dimension TYPE 0508 (4 X 0402) 0612 (4 X 0603) Tmin. (mm) 0.50 0.70 Tmax. (mm) 0.70 0.90 Table 2 For outlines see fig. 3
www.yageo.com Mar. 31, 2017 V.6 Surface-Mount Ceramic Multilayer Capacitors Product specification CAPACITANCE RANGE & THICKNESS FOR NP0 Table 3 Sizes from 0402 to 0805 CAP. 0402 0603 0805
50 V 50 V 100 V 250 V 50 V 100 V 250V
- Values in shaded cells indicate thickness class in mm
www.yageo.com Mar. 31, 2017 V.6 Surface-Mount Ceramic Multilayer Capacitors Product specification CAPACITANCE RANGE & THICKNESS FOR NP0 Table 4 Sizes from 0402 to 0805 (continued) CAP. 0402 0603 0805
50 V 50 V 100 V 250 V 50 V 100 V 250 V
1.2 nF 1.5 nF 1.8 nF 2.2 nF 2.7 nF 3.3 nF 3.9 nF 4.7 nF 5.6 nF 6.8 nF 8.2 nF 10 nF NOTE Values in shaded cells indicate thickness class in mm
www.yageo.com Mar. 31, 2017 V.6 Surface-Mount Ceramic Multilayer Capacitors Product specification CAPACITANCE RANGE & THICKNESS FOR NP0 Table 5 Sizes from 1206 to 1210 CAP. 1206 1210
50 V 100 V 250 V 500 V 630 V 50 V 100 V 250 V 500 V
3.3 nF 3.9 nF 4.7 nF 5.6 nF 6.8 nF 8.2 nF 10 nF NOTE Values in shaded cells indicate thickness class in mm
www.yageo.com Mar. 31, 2017 V.6 Surface-Mount Ceramic Multilayer Capacitors Product specification Table 6 Sizes from 0402 to 0603 CAPACITANCE RANGE & THICKNESS FOR X7R CAP. 0402 0603 10V 16 V 25 V 50 V 10V 16 V 25 V 50 V 100 V 100 pF 150 pF 150 nF 0.8± 0.1 0.8± 0.1 330 nF 470 nF 0.8± 0.1 0.8± 0.1 680 nF 1 µF 0.8± 0.1 NOTE Values in shaded cells indicate thickness class in mm
www.yageo.com Mar. 31, 2017 V.6 Surface-Mount Ceramic Multilayer Capacitors Product specification CAPACITANCE RANGE & THICKNESS FOR X7R Table 8 Size 0805 CAP. 0805
10 V 16 V 25 V 50 V 100 V 250 V 500 V
1.25± 0.2 1.25± 0.2 1.25± 0.2 1.25± 0.2 2.2 µF 1.25± 0.2 NOTE Values in shaded cells indicate thickness class in mm
www.yageo.com Mar. 31, 2017 V.6 Surface-Mount Ceramic Multilayer Capacitors Product specification Table 9 Size 1206 CAPACITANCE RANGE & THICKNESS FOR X7R CAP. 1206
6.3 V 10V 16V 25V 50 V 100 V 250 V
Values in shaded cells indicate thickness class in mm
www.yageo.com Mar. 31, 2017 V.6 Surface-Mount Ceramic Multilayer Capacitors Product specification CAP. 1210 1812 6.3V 10 V 16 V 25 V 50V 100 V 250 V 50V 100V NOTE Values in shaded cells indicate thickness class in mm CAPACITANCE RANGE & THICKNESS FOR X7R Table 10 Size 1210
www.yageo.com Mar. 31, 2017 V.6 Surface-Mount Ceramic Multilayer Capacitors Product specification CAPACITANCE RANGE & THICKNESS FOR 4C-ARRAY Table 11 Temperature characteristic material from NP0 CAPACITANCE 0508 (4 x 0402) 0612 (4 x 0603)
50 V 50 V
100 pF 0.6± 0.1 0.8± 0.1 120 pF 0.8± 0.1 150 pF 0.8± 0.1 180 pF 0.8± 0.1 220 pF 0.8± 0.1 270 pF 0.8± 0.1 330 pF 0.8± 0.1 390 pF 0.8± 0.1 470 pF 0.8± 0.1 560 pF 680 pF 820 pF 1.0 nF NOTE Values in shaded cells indicate thickness class in mm
www.yageo.com Mar. 31, 2017 V.6 Surface-Mount Ceramic Multilayer Capacitors Product specification CAPACITANCE RANGE & THICKNESS FOR 4C-ARRAY Table 12 Temperature characteristic material from X7R CAPACITANCE 0508 (4 x 0402) 0612 (4 x 0603)
16 V 25 V 50 V 16 V 25 V 50 V
68 nF 0.6± 0.1 100 nF 0.6± 0.1 NOTE Values in shaded cells indicate thickness class in mm
www.yageo.com Mar. 31, 2017 V.6 Surface-Mount Ceramic Multilayer Capacitors Product specification Table 13 THICKNESS CLASSES AND PACKING QUANTITY SIZE CODE THICKNESS CLASSIFICATION TAPE WIDTH QUANTITY PER REEL Ø 180 MM / 7 INCH Ø 330 MM / 13 INCH Paper Blister Paper Blister 0402 0.5 ± 0.05 mm 8 mm 10,000 --- 50,000 --- 1210 1812
www.yageo.com Mar. 31, 2017 V.6 Surface-Mount Ceramic Multilayer Capacitors Product specification
ELECTRICAL CHARACTERISTICS
NNPP00//XX77RR DDIIEELLEECCTTRRIICC CCAAPPAACCIITTOORRSS;; NNII//SSIINN TTEERRMMIINNAATTIIOONNSS Unless otherwise specified, all test and measurements shall be made under standard atmospheric conditions for testing as given in 5.3 of IEC 60068 -1: - Temperature: 15 °C to 35 °C - Relative humidity: 25% to 75% - Air pressure: 86 kPa to 106 kPa Before the measurements are made, the capacitor shall be stored at the measuring temperature for a time sufficient to allow the entire capacitor to reach this temperature. The period as pres cribed for recovery at the end of a test is normally sufficient for this purpose. Table 14 DESCRIPTION VALUE Capacitance range 0.47 pF to 1 µF Capacitance tolerance NP0 C < 10 pF ± 0.25 pF, ± 0.5 pF Dissipation factor (D.F.) NP0 C < 30 pF ≤ 1 / ( 400 + 20C ) C ≥ 30 pF ≤ 0.1 % X7R 0402 0603 0805 1206 1210 1812 0508 (Array) 0612 (Array) ≤10V 220pF to 100nF 1nF to 1uF 1nF to 2.2uF 22nF to 1uF 100nF to 1uF ≤5% 16V 220pF to 22nF 1nF to 220nF 1nF to 470nF 22nF to 1uF 100nF to 1uF 1nF to 10nF 220pF to 47nF ≤3.5% 27nF to 100nF 470nF 680nF to 1uF 15nF to 100nF ≤5% 25V 220pF to 10nF 1nF to 39nF 1nF to 180nF 22nF to 680nF 100nF to 1uF 1nF to 10nF 220pF to 47nF ≤2.5% 12nF to 47nF 47nF to 220nF 220nF to 470nF 1uF ≤3.5% 680nF to 1uF ≤5% 50V 220pF to 10nF 1nF to 39nF 1nF to 100nF 22nF to 470nF 100nF to 1uF 470nF to 1uF 1nF 220pF to 10nF ≤2.5% 47nF to 100nF 220nF ≤3.5% 100V 1nF to 10nF 1nF to 100nF 22nF to 220nF 100nF to 220nF 470nF to 1uF ≤2.5% 12nF to 47nF ≤5% 250V 1nF to 22nF 22nF 100nF ≤2.5% 500V 1nF to 4.7nF ≤2.5% Insulation resistance after 1 minute at Ur (DC) IR ≥ 10 GΩ or I.R × C ≥ 500 seconds whichever is less Maximum capacitance change as a function of temperature (temperature characteristic/coefficient): NP0 ± 30 ppm/°C X7R ± 15% Operating temperature range: NP0/X7R –55 °C to +125 °C NOTE 1. Capacitance tolerance ±5% doesn't available for X7R full product range, please contact local sales force before order
www.yageo.com Mar. 31, 2017 V.6 Surface-Mount Ceramic Multilayer Capacitors Product specification SOLDERING CONDITIONS The lead free MLCCs are able to stand the reflow soldering conditions as below: Temperature: above 220 °C Endurance: 95 to 120 seconds Cycles: 3 times The test of "soldering heat resistance" is carried out in accordance with the schedule of "MIL-STD-202F-method 210F", "The robust construction of chip capacitors allows them to be completely immersed in a solder bath of 270 °C for 10 seconds". Therefore, it is possible to mount MLCCs on one side of a PCB and other discrete components on the reverse (mixed PCBs). Surface Mount Capacitors are tested for solderability at 245 °C during 2 seconds. The test condition for no leaching is 260°C for 30 seconds. TEST TEST METHOD PROCEDURE REQUIREMENTS Mounting IEC 60384-
4.3 The capacitors may be mounted on printed-circuit boards or
4.5.1 Class 1:
At 20 °C, 24 hours after annealing f = 1 MHz for C ≤ 1nF, measuring at voltage 1 Vrms at 20 °C f = 1 KHz for C > 1nF, measuring at voltage 1 Vrms at 20 °C Class 2: At 20 °C, 24 hours after annealing f = 1 KHz, measuring at voltage 1 Vrms at 20 °C Within specified tolerance Dissipation Factor (D.F.) IEC 60384-
4.5.2 Class 1:
At 20 °C, 24 hours after annealing f = 1 MHz for C ≤ 1nF, measuring at voltage 1 Vrms at 20 °C f = 1 KHz for C > 1nF, measuring at voltage 1 Vrms at 20 °C Class 2: At 20 °C, 24 hours after annealing f = 1 KHz, measuring at voltage 1 Vrms at 20 °C In accordance with specification Insulation Resistance IEC 60384-
4.5.3 At Ur (DC) for 1 minute In accordance with
0402 0603 0805 1206 ≥ 1210 Reflow ≥ 0.1 µF ≥ 1.0 µF ≥ 2.2 µF ≥ 4.7 µF Reflow only Reflow/Wave < 0.1 µF < 1.0 µF < 2.2 µF < 4.7 µF --- TESTS AND REQUIREMENTS Table 16 Test procedures and requirements
www.yageo.com Mar. 31, 2017 V.6 Surface-Mount Ceramic Multilayer Capacitors Product specification TEST TEST METHOD PROCEDURE REQUIREMENTS Temperature coefficient
4.6 Capacitance shall be measured by the steps shown in the
following table. The capacitance change should be measured after 5 min at each specified temperature stage. Step Temperature(℃) a 25± 2 b Lower temperature± 3℃ c 25± 2 d Upper Temperature± 2℃ e 25± 2 (1) Class I Temperature Coefficient shall be calculated from the formula as below Temp, Coefficient = 610T xC1 C1-C2 Δ [ppm/℃] C1: Capacitance at step c C2: Capacitance at 125℃ (2) Class II Capacitance Change shall be calculated from the formula as below ∆C = C1-C2 x 100% C1: Capacitance at step c C2: Capacitance at step b or d <General purpose series> Class1: ∆ C/C: ± 30ppm Class2: X7R: ∆ C/C: ±15% <High Capacitance series> Class2: X7R/X5R: ∆ C/C: ±15% High Temperature Exposure AEC-Q200 3 Unpowered ; 1000hours @ T=150℃ Measurement at 24± 2 hours after test conclusion. No visual damage Δ C/C: Class1: NP0: within ± 0.5% or 0.5 pF whichever is greater Class2: X7R: ± 10% D.F.: within initial specified value IR: within initial specified value
www.yageo.com Mar. 31, 2017 V.6 Surface-Mount Ceramic Multilayer Capacitors Product specification TEST TEST METHOD PROCEDURE REQUIREMENTS Temperature Cycling AEC-Q200 4 Preconditioning; 150 +0/–10 °C for 1 hour, then keep for 24 ± 1 hours at room temperature 1000 cycles with following detail: 30 minutes at lower category temperature 30 minutes at upper category temperature Recovery time 24 ± 2 hours No visual damage ∆C/C Class1: NP0: Within ± 1% or 0.5pF, whichever is greater. Class2: X7R: ±10% D.F. meet initial specified value IR meet initial specified value Destructive Physical Analysis AEC-Q200 5 10ea X 3 lots. Note: Only applies to SMD ceramics. Electrical test not required. Moisture Resistance AEC-Q200 6 T=24 hrs/per cycle; 10 continuous cycles unpowered. Measurement at 24 ± 2 hours after test condition. No visual damage ∆C/C NP0: Within ± 3% or 3 pF, whichever is greater X7R: ± 10% D.F. Within initial specified value IR NP0: ≥ 10,000 MΩ X7R: Meet initial specified value Fig. 4 Moisture resistant
www.yageo.com Mar. 31, 2017 V.6 Surface-Mount Ceramic Multilayer Capacitors Product specification TEST TEST METHOD PROCEDURE REQUIREMENTS Biased Humidity AEC-Q200 7 1. Preconditioning, class 2 only: 150 +0/-10 °C /1 hour, then keep for 24 ± 1 hour at room temp 2. Initial measure: Parameter: IR Measuring voltage: 1.5V ± 0.1 VDC Note: Series with 100 KΩ & 6.8 KΩ 3. Test condition: 85 °C, 85% R.H. connected with 100 KΩ resistor, applied 1.5V/Ur for 1,000 hours. 4. Recovery: Class1: 6 to 24 hours Class2: 24 ± 2 hours 5. Final measure: IR No visual damage after recovery Initial requirement: Class1: - Connected to 100 KΩ: C ≤ 10 nF: I.R ≥ 10,000 MΩ or C > 10 nF: (I.R-100 KΩ) x C ≥ 100s. - Connected to 6.8 KΩ: C ≤ 10 nF: I.R ≥ 10,000 MΩ or C > 10 nF: (I.R-6.8 KΩ) x C ≥ 100s. Class2: - Connected to 100 KΩ: C ≤ 25 nF: I.R ≥ 4,000 MΩ or C > 25 nF: (I.R-100 KΩ) x C ≥ 100s. - Connected to 6.8 KΩ: C ≤ 25 nF: I.R ≥ 10,000 MΩ or C > 25 nF: (I.R-6.8 KΩ) x C ≥ 100s. Final measurement: The insulation resistance shall be greater than 0.1 time initial value.
www.yageo.com Mar. 31, 2017 V.6 Surface-Mount Ceramic Multilayer Capacitors Product specification TEST TEST METHOD PROCEDURE REQUIREMENTS Operational Life AEC-Q200 8 1. Preconditioning, class 2 only: 150 +0/-10 °C /1 hour, then keep for 24 ± 1 hour at room temp 2. Initial measure: Spec: refer to initial spec C, D, IR 3. Endurance test: Temperature: X7R: 125 °C Specified stress voltage applied for 1,000 hours: Applied 2.0 x Ur for general products Applied 1.5 x Ur for high cap. Products High voltage series follows with below stress condition: Applied 1.5 x Ur for 200V, 250V series Applied 1.3 x Ur for 500V, 630V series Applied 1.2 x Ur for 1KV, 2KV, 3KV series 4. Recovery time: 24 ± 2 hours 5. Final measure: C, D, IR Note: If the capacitance value is less than the minimum value permitted, then after the other measurements have been made the capacitor shall be preconditioned according to “IEC 60384 4.1” and then the requirement shall be met. No visual damage ∆C/C NP0: Within ± 2% or 1 pF, whichever is greater X7R: ± 15% D.F. NP0: ≤ 2 x specified value. X7R: ≤ 16V: ≤ 7% ≥ 25V: ≤ 5% IR NP0: ≥ 4,000 MΩ or IR x Cr ≥ 40s whichever is less X7R: ≥ 1,000 MΩ or IRx Cr ≥ 50s whichever is less External Visual AEC-Q200 9 Any applicable method using × 10 magnification In accordance with specification Physical Dimension AEC-Q200 10 Verify physical dimensions to the applicable device specification. In accordance with specification Mechanical Shock AEC-Q200 13 Three shocks in each direction shall be applied along the three mutually perpendicular axes of the test specimen (18 shocks) Peak value: 1,500 g’s Duration: 0.5 ms Velocity change: 15.4 ft/s Waveform: Half-sin ∆C/C NP0: Within ± 0.5% or 0.5 pF, whichever is greater X7R: ± 10% D.F. Within initial specified value IR Within initial specified value Vibration AEC-Q200 14 5 g’s for 20 minutes, 12 cycles each of 3 orientations. Note: Use 8” x 5” PCB. 0.31” thick 7 secure points on one long side and 2 secure points at corners of opposite sides. Parts mounted within 2” from any secure point. Test from 10-2000 Hz. ∆C/C NP0: Within ± 0.5% or 0.5 pF, whichever is greater X7R: ± 10% D.F: meet initial specified value IR meet initial specified value
www.yageo.com Mar. 31, 2017 V.6 Surface-Mount Ceramic Multilayer Capacitors Product specification TEST TEST METHOD PROCEDURE REQUIREMENTS Resistance to Soldering Heat AEC-Q200 15 Precondition: 150 +0/–10 °C for 1 hour, then keep for 24 ± 1 hours at room temperature Preheating: for size ≤ 1206: 120 °C to 150 °C for 1 minute Preheating: for size >1206: 100 °C to 120 °C for 1 minute and 170 °C to 200 °C for 1 minute Solder bath temperature: 260 ± 5 °C Dipping time: 10 ± 0.5 seconds Recovery time: 24 ±2 hours Dissolution of the end face plating shall not exceed 25% of the length of the edge concerned ∆C/C Class1: NP0: Within ± 1% or 0.5 pF, whichever is greater. Class2: X7R: ± 10% D.F. within initial specified value IR within initial specified value Thermal Shock AEC-Q200 16 1. Preconditioning, class 2 only: 150 +0/-10 °C /1 hour, then keep for 24 ± 1 hour at room temp 2. Initial measure: Spec: refer to initial spec C, D, IR 3. Rapid change of temperature test: NP0/X7R: -55 °C to +125 °C; 300 cycles 15 minutes at lower category temperature; 15 minutes at upper category temperature. 4. Recovery time: Class1: 6 to 24 hours Class2: 24 ± 2 hours 5. Final measure: C, D, IR No visual damage ∆C/C NP0: Within ± 1% or 1 pF, whichever is greater X7R: ± 15% D.F: meet initial specified value IR meet initial specified value ESD AEC-Q200 17 Per AEC-Q200-004 A component passes a voltage level if all components stressed at that voltage level pass. Solderability AEC-Q200
18 Preheated to a temperature of 80 °C to 140 °C and
maintained for 30 seconds to 60 seconds. Test conditions for lead containing solder alloy Temperature: 235 ± 5 °C Dipping time: 2 ± 0.2 seconds Depth of immersion: 10 mm Alloy Composition: 60/40 Sn/Pb Number of immersions: 1 Test conditions for lead-free containing solder alloy Temperature: 245 ± 5 °C Dipping time: 3 ± 0.3 seconds Depth of immersion: 10 mm Alloy Composition: SAC305 Number of immersions: 1 The solder should cover over 95% of the critical area of each termination.
www.yageo.com Mar. 31, 2017 V.6 Surface-Mount Ceramic Multilayer Capacitors Product specification TEST TEST METHOD PROCEDURE REQUIREMENTS Electrical Characterization AEC-Q200 19 Parametrically test per lot and sample size requirements, summary to show Min, Max, Mean and Standard deviation at room as well as Min and Max operating temperatures. ∆C/C Class 1: NP0: ± 30 ppm/°C Class2: X7R: ± 15% Class 1: NP0: -55 °C to +125 °C Normal temperature: 20 °C Class 2: X7R: -55 °C to +125 °C Normal temperature: 20 °C Board Flex AEC-Q200 21 Part mounted on a 100 mm X 40 mm FR4 PCB board, which is 1.6 ± 0.2 mm thick and has a layer-thickness 35 µm ± 10 µm. Part should be mounted using the following soldering reflow profile. Conditions: Class1: Bending 3 mm at a rate of 1 mm/s, radius jig 340 mm Class2: Bending 2 mm at a rate of 1 mm/s, radius jig 340 mm Test Substrate: 100 b C a 4.5 YNSC147 unit: mm No visible damage ∆C/C Class1: NP0: Within ± 1% or 0.5 pF, whichever is greater Class2: X7R: ± 10% Dimension(mm) Type a b c 0201 0.3 0.9 0.3 0402 0.4 1.5 0.5 0603 1.0 3.0 1.2 0805 1.2 4.0 1.65 1206 2.2 5.0 1.65 1210 2.2 5.0 2.0 1808 3.5 7.0 3.7 Terminal Strength AEC-Q200 22 With the component mounted on a PCB obtained with the device to be tested, apply a 17.7N (1.8Kg) force to the side of a device being tested. This force shall be applied for 60+1 seconds. Also the force shall be applied gradually as not to apply a shock to the component being tested. * Apply 2N force for 0402 size. Magnification of 20X or greater may be employed for inspection of the mechanical integrity of the device body, terminals and body/terminal junction. Before, during and after the test, the device shall comply with all electrical requirements stated in this specification.
www.yageo.com Mar. 31, 2017 V.6 Surface-Mount Ceramic Multilayer Capacitors Product specification TEST TEST METHOD PROCEDURE REQUIREMENTS Beam Load Test AEC-Q200 23 Place the part in the beam load fixture. Apply a force until the part breaks or the minimum acceptable force level required in the user specification(s) is attained. ≤ 0805 Thickness > 0.5mm: 20N Thickness ≤ 0.5mm: 8N ≥ 1206 Thickness ≥1.25 mm: 54N Thickness < 1.25 mm: 15N Note: Classify the components according to the highest ESD voltage level survived during ESD testing. Fig. 5 Passive component HBM ESD test flow diagram (DC = Direct Contact Discharge, AD = Air Discharge)
www.yageo.com Mar. 31, 2017 V.6 Surface-Mount Ceramic Multilayer Capacitors Product specification
REVISION HISTORY
REVISION DATE CHANGE NOTIFICATION DESCRIPTION Version 6 Mar.31, 2017 - - Add NPO/0603/1nF/50V, X7R/0603/1uF/10V, X7R/0603/470nF/16V, X7R/0603/220nF/25V Version 5 Nov. 15, 2016 - - Add Soldering Condition Version 4 Jun. 14, 2016 - - Add X7R/0805/2.2uF/10V and NPO/1206/1.2nF to 1.5nF/250V Version 3 Jul. 21, 2015 - - Tests and Requirements update Version 2 Jul. 17, 2014 - - Tests and Requirements update Version 1 Apr. 19, 2013 - - Capacitance range update Version 0 Dec. 25, 2012 - - New
www.yageo.com Mar. 31, 2017 V.6 Surface-Mount Ceramic Multilayer Capacitors Product specification LEGAL DISCLAIMER Yageo, its distributors and agents (collectively, “Yageo”), hereby disclaims any and all liabilities for any errors, inaccuracies or incompleteness contained in any product related information, including but not limited to product specifications, datasheets, pictures and/or graphics. Yageo may make changes, modifications and/or improvements to product related information at any time and without notice. Yageo makes no representation, warranty, and/or guarantee about the fitness of its products for any particular purpose or the continuing pro duction of any of its products. To the maximum extent permitted by law, Yageo disclaims (i) any and all liability arising out of the application or use of any Yageo product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for a particular purpose, non -infringement and merchantability. Yageo statements regarding the suitability of products for certain types of applications are ba sed on Yageo’s knowledge of typical operating conditions for such types of applications in a generic nature. Such statements are neither binding statements of Yageo nor intended to constitute any warranty concerning the suitability for a specific customer application or use. They are intended for use only by customers with requisite knowledge and experience for determining whether Yageo products are the correct products for their application or use. In addition, unpredicatable and isolated cases of product failure may still occur, therefore, customer application or use of Yageo products which requires higher degree of reliability or safety, shall employ additional protective safeguard measures to ensure that product failure would not result in personal injur y or property damage. Yageo products are not designed for application or use in medical, life -saving, or life -sustaining devices or for any other application or use in which the failure of Yageo products could result in personal injury or death. Customer s using or selling Yageo products not expressly indicated for above -mentioned purposes shall do so at their own risk and agree to fully indemnify Yageo and hold Yageo harmless. Information provided here is intend ed to indicate product specifications only. Yageo reserves all the rights for revising this content without further notification, as long as products are unchanged. Any product change will be announced by PCN.