AAT3141

AAT3141 AAT

Document overview

• Manufacturer or author: Provided By www.digicamel.com(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 16

Technical content

Features

• V IN Range: 2.7V to 5.5V
• Tri-Mode 1X, 1.5X, and 2X Charge Pump for Maximum Efficiency and VF Coverage
• Drives Low-V F and High-VF Type LEDs
• Up to Four 30mA Outputs
• A S 2Cwire Independent 3+1 Output Addressing
• 32-Position Logarithmic Scale with Digital Control
• Low Noise Constant Frequency Operation
• 1MHz Switching Frequency
• AutoBias Technology
• Small Application Circuit
• Regulated Output Current
• Automatic Soft Start
• No Inductors Q <1µA in Shutdown
• 12-Pin TSOPJW Package

Applications

• Color (RGB) Lighting
• Programmable Current Sources
• White LED Backlighting
• White Photo Flash for Digital Still Cameras Typical Application CIN 1μF VBATTERY CCP 1μF EN/SET 1μF 1μF D3 D2 D1 VIN CP C1+ C1- C2+ C2- EN/SET GND AAT3141

High Efficiency 1X/1.5X/2X Charge Pump for White LED Applications 2 3141.2007.03.1.3 Pin Descriptions Pin Configuration TSOPJW-12 (Top View) Pin # Symbol Function 1 C2+ Flying capacitor 2 positive terminal. Connect a 1µF capacitor between C2+ and C2-. 2 CP Charge pump output. Requires 1µF capacitor connected between this pin and ground. 3 C1- Flying capacitor 1 negative terminal. 4 C1+ Flying capacitor 1 positive terminal. Connect a 1µF capacitor between C1+ and C1-. 5 D3 Current source output #3. 6 D2 Current source output #2. 7 D4 Current source output #4. 8 D1 Current source output #1. 9 EN/SET AS 2Cwire serial interface control pin. 10 IN Input power supply. Requires 1µF capacitor connected between this pin and ground. 11 GND Ground. 12 C2- Flying capacitor 2 negative terminal. C2+ CP C1- C1+ C2- GND IN EN/SET

High Efficiency 1X/1.5X/2X Charge Pump for White LED Applications 3141.2007.03.1.3 3 Absolute Maximum Ratings1 Thermal Information3 Symbol Description Value Units VIN Input Voltage -0.3 to 6 V VEN/SET EN/SET to GND Voltage -0.3 to VIN + 0.3 V IOUT

2 Maximum DC Output Current 150 mA

TJ Operating Junction Temperature Range -40 to 150 °C Symbol Description Value Units PD Maximum Power Dissipation4 625 mW θJA Maximum Thermal Resistance 160 °C/W 1. Stresses above those listed in Absolute Maximum Ratings may cause permanent damage to the device. Functional operation at condi- tions other than the operating conditions specified is not implied. Only one Absolute Maximum Rating should be applied at any one time. 2. Based on long-term current density limitation. 3. Mounted on an FR4 board. 4. Derate 6.25mW/°C above 25°C.

High Efficiency 1X/1.5X/2X Charge Pump for White LED Applications 4 3141.2007.03.1.3 Electrical Characteristics1 CIN = CCP = C1 = C2 = 1.0µF; TA = -40°C to +85°C, unless otherwise noted. Typical values are at T A = 25°C, VIN = 3.5V. Symbol Description Conditions Min Typ Max Units Input Power Supply VIN Operation Range 2.7 5.5 V Icc Operating Current VD1:D4 = 2.0V, CP = 1X 550 µA No Load Current, CP = 1.5X 3 5 mA ISHDN Shutdown Current VIN = 3.5V, EN/SET = 0 1 µA IDX Output Current Accuracy2 VIN = 3.5V, TA = 25°C -10 10 % VIN = 3.5V, TA = 25°C, Code 28 17.1 19 20 mA I(D-Match) Current Matching3 VD1:D4 = 3.6V, VIN = 3.5V -3 ±0.5 3 % ηCP Charge Pump Section Efficiency VIN = 3.5V, IOUT(TOTAL)= 120mA, 93 %Measured from IN to CP Charge Pump Section TSS Soft-Start Time 50 µs FCLK Clock Frequency 1 MHz EN/SET VEN(L) Enable Threshold Low VIN = 2.7V 0.4 V VEN(H) Enable Threshold High VIN = 5.5V 1.4 V TEN/SET LO EN/SET Low Time 0.3 75 µs TEN/SET HI MIN Minimum EN/SET High Time 50 ns TEN/SET HI MAX Maximum EN/SET High Time 75 µs TOFF EN/SET Off Timeout 500 µs TLAT EN/SET Latch Timeout 500 µs IEN/SET EN/SET Input Leakage VEN/SET = 5.5V, VIN = 5.5V -1 1 µA 1. The AAT3141 is guaranteed to meet performance specifications over the -40°C to +85°C operating temperature range and is assu red by design, characterization, and correlation with statistical process controls. 2. Codes 2 through 7 are guaranteed to be within ±15% of stated current level. 3. Current matching is defined as I (D-Match) = (ID - IAVE)/IAVE.

High Efficiency 1X/1.5X/2X Charge Pump for White LED Applications 3141.2007.03.1.3 5 Typical Characteristics Unless otherwise noted, VIN = 3.5V, CIN = CCP = C1 = C2 = 1µF, TA = 25°C. Efficiency vs. Input Voltage Input Voltage (V) Efficiency (%) 506070 8090 100 Code 32Code 28 Code 26 Input Voltage (V) Efficiency (%) 506070 8090 100 Efficiency vs. Input Voltage (Code 26) 3.5VF 3.0VF Input Voltage (V) Efficiency (%) 506070 8090 100 Code 32Code 28 Code 26 Efficiency vs. Input Voltage

High Efficiency 1X/1.5X/2X Charge Pump for White LED Applications 6 3141.2007.03.1.3 Typical Characteristics Unless otherwise noted, VIN = 3.5V, CIN = CCP = C1 = C2 = 1µF, TA = 25°C. Line Response (1X Mode, 4x30mA Load) Time (1ms/div) VIN (0.5V/div) VLED (20mV/div) VCP (0.5V/div) ID (10mA/div) Line Response (1X Mode, 4x19mA Load) Time (1ms/div) VIN (0.5V/div) VLED (20mV/div) VCP (0.5V/div) ID (10mA/div) Line Response (1.5X Mode, 4x30mA Load) Time (1ms/div) VIN (0.5V/div) VLED (20mV/div) VCP (0.5V/div) ID (10mA/div) Line Response (1.5X Mode, 4x19mA Load) Time (1ms/div) VIN (0.5V/div) VLED (20mV/div) VCP (0.5V/div) ID (10mA/div) Load Characteristics (1.5X Mode, 4x30mA Load) Time (1μμs/div) VF (20mV/div) IIN (10mA/div) VCP (20mV/div) Load Characteristics (1.5X Mode, 4x15mA Load) Time (1μμs/div) VF (20mV/div) IIN (10mA/div) VCP (20mV/div)

High Efficiency 1X/1.5X/2X Charge Pump for White LED Applications 3141.2007.03.1.3 7 Typical Characteristics Unless otherwise noted, VIN = 3.5V, CIN = CCP = C1 = C2 = 1µF, TA = 25°C. Charge Pump to Load Switch (1.5X Mode, 4x30mA Load) Time (5ms/div) VIN (500mV/div) VCP (1V/div) VDIODE (500mV/div) IIN (50mA/div) Charge Pump to Load Switch (1.5X Mode, 4x19mA Load) Time (5ms/div) VIN (500mV/div) VCP (1V/div) VDIODE (500mV/div) IIN (50mA/div) Charge Pump to Load Switch (2X Mode, 4x30mA Load) Time (5ms/div) VIN (500mV/div) VCP (1V/div) VDIODE (500mV/div) IIN (50mA/div) Charge Pump to Load Switch (2X Mode, 4x19mA Load) Time (5ms/div) VIN (500mV/div) VCP (1V/div) VDIODE (500mV/div) IIN (50mA/div) Load Switch to Charge Pump (1.5X Mode, 4x30mA Load) Time (2ms/div) VIN (1V/div) VCP (4V/div) VDIODE (500mV/div) IIN (50mA/div) Load Switch to Charge Pump (1.5X Mode, 4x19mA Load) Time (2ms/div) VIN (1V/div) VCP (4V/div) VDIODE (500mV/div) IIN (50mA/div)

High Efficiency 1X/1.5X/2X Charge Pump for White LED Applications 8 3141.2007.03.1.3 Typical Characteristics Unless otherwise noted, VIN = 3.5V, CIN = CCP = C1 = C2 = 1µF, TA = 25°C. Turn-On to 1X Mode (4x30mA Load) Time (100µs/div) EN/SET (2V/div) VCP (4V/div) VDIODE (2V/div) IIN (100mA/div) Turn-On to 1X Mode (4x19mA Load) Time (100µs/div) EN/SET (2V/div) VCP (4V/div) VDIODE (2V/div) IIN (100mA/div) Turn-On to 1.5X Mode (4x30mA Load) Time (100µs/div) EN/SET (2V/div) VCP (4V/div) VDIODE (2V/div) IIN (100mA/div) Turn-On to 1.5X Mode (4x19mA Load) Time (100µs/div) EN/SET (2V/div) VCP (4V/div) VDIODE (2V/div) IIN (100mA/div) Turn-Off from Full-Scale 2X Mode Time (100µs/div) EN/SET (2V/div) VDIODE (2V/div) IIN (200mA/div)

High Efficiency 1X/1.5X/2X Charge Pump for White LED Applications 3141.2007.03.1.3 9 Typical Characteristics Unless otherwise noted, VIN = 3.5V, CIN = CCP = C1 = C2 = 1µF, TA = 25°C. Input Voltage (V) IIN (mA) Input Current vs. Input Voltage (4x30mA) 100 150 200 250300 VDIODE = 3.0V VDIODE = 3.4V Input Voltage (V) IIN (mA) Input Current vs. Input Voltage (4x10mA) 60708090 VDIODE = 3.4V VDIODE = 3.0V VIH and VIL vs. VIN Input Voltage (V) 0.600 0.625 0.650 0.675 0.700 0.725 0.750 0.775 0.800 0.825 0.850 VIH VIL Input Voltage (V) IDIODE (mA) Diode Current vs. Input Voltage (30mA, 15mA Settings) 1520 3035 VDIODE = 3.4V VDIODE = 3.4V

High Efficiency 1X/1.5X/2X Charge Pump for White LED Applications 10 3141.2007.03.1.3 Functional Block Diagram 1.5X Charge Pump Soft-Start Control 1MHz Oscillator Voltage Reference 32 x 8 bit ROM C1+ C1- C2+C2- CP GND EN/SET VIN 32 x 8 bit ROM AS2Cwire Interface D/A D/A D/A D/A Functional Description The AAT3141 is a tri-mode load switch (1X) and high efficiency (1.5X or 2X) charge pump device intended for white LED backlight applications. To maximize power conversion efficiency, an internal sensing circuit monitors the voltage required on each constant current source output and sets the load switch and charge pump modes based on the input battery voltage and the current source output voltage. As the battery discharges over time, the AAT3141 charge pump is enabled when any of the four current source outputs nears dropout. The charge pump initially starts in 1.5X mode. If the charge pump output drops enough for any current source output to become close to dropout, the charge pump will automatically transition to 2X mode. AutoBias Technology Each of the four current source outputs is inde- pendently switched between the battery input (1X) or the charge pump output (1.5X or 2X), depending on the voltage at the current source output. Since the LED-to-LED forward voltage (V F) can vary as much as 1V, this function significantly enhances overall device efficiency when the battery input voltage level is greater than the voltage required at any current source output. The AAT3141 requires only four external compo- nents: two 1µF ceramic capacitors for the charge pump flying capacitors (C 1 and C 2), one 1µF ceramic input capacitor (C IN), and one 0.33µF to 1µF ceramic charge pump output capacitor (C CP). The four constant current outputs (D1 to D4) drive four individual LEDs with a maximum current of 30mA each. The EN/SET AS 2Cwire serial interface enables the AAT3141 and sets the current source magnitudes.

High Efficiency 1X/1.5X/2X Charge Pump for White LED Applications 3141.2007.03.1.3 11 Applications Information Constant Current Output Level Settings The constant current source amplitudes for D1 to D4 are set via the serial interface according to a loga- rithmic scale where each code is 1dB greater than the previous code. In this manner, LED brightness appears linear with each increasing code count. Because the outputs D1 to D4 are true independent constant current sources, the voltage observed on any single given output will be determined by the actual forward voltage (V F) for the LED being driven. Since the output current of the AAT3141 is pro- grammable, no PWM (pulse width modulation) or additional control circuitry are needed to control LED brightness. This feature greatly reduces the burden on a microcontroller or system IC to manage LED or display brightness, allowing the user to "set it and forget it." With its high-speed serial interface (1MHz data rate), the output current of the AAT3141 can be changed successively to brighten or dim LEDs in smooth transitions (e.g., to fade out) or in abrupt steps, giving the user complete programma- bility and real-time control of LED brightness. The individual current level settings are each approximately 1dB apart for settings above Code 8 (see Figure 1). The current level settings below Code 8 are more than 1dB apart and serve the needs of transmissive displays and other low-cur- rent applications. Figure 1: Normalized Current Level Settings. Table 2: Constant Current Source Output Nominal Programming Levels. IOUT (typ) IOUT (typ) IOUT (typ) IOUT (typ) Code (mA) Code (mA) Code (mA) Code (mA) 1 0.0 9 2.0 17 5.1 25 13 2 0.1 10 2.2 18 5.6 26 15 3 0.2 11 2.5 19 6 27 17 4 0.4 12 2.8 20 7 28 19 5 0.5 13 3.2 21 8 29 21 6 0.7 14 3.5 22 9 30 24 7 1.1 15 4.0 23 10 31 27 8 1.8 16 4.5 24 12 32 30 0.00 0.01 0.10 1.00 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 Code Current (mA)

High Efficiency 1X/1.5X/2X Charge Pump for White LED Applications 12 3141.2007.03.1.3 AS2Cwire Serial Interface The current source output magnitude is controlled by the AS2Cwire serial digital input. AS2Cwire adds addressing capability for multiple data registers over the Simple Serial Control™ (S 2Cwire™), which is only capable of controlling a single regis- ter. The AAT3141 has two registers. One contains the current level setting for outputs D1 to D3, and the other contains the current level setting for out- put D4. Three addresses are used to control the two regis- ters. Address 0 addresses both registers simulta- neously to allow the loading of both registers with the same data using a single write protocol. Address 1 addresses Register 1 for D1 to D3 cur- rent level settings. Address 2 addresses Register 2 for D4 current level settings. As with S 2Cwire, AS2Cwire relies on the number of rising edges of the EN/SET pin to address and load the registers. AS 2Cwire latches data or address after the EN/SET pin has been held high for time TLAT. Address or data is differentiated by the num- ber of EN/SET rising edges. Since the data regis- ters are 5 bits each, the differentiating number of pulses is 2 5 or 32, so that Address 0 is signified by 33 rising edges, Address 1 by 34 rising edges and Address 2 by 35 rising edges. Data is set to any number of rising edges between 1 and including 32. A typical write protocol is a burst of EN/SET ris- ing edges, signifying a particular address, followed by a pause with EN/SET held high for the T LAT time- out period, a burst of rising edges signifying data, and a T LAT timeout for the data registers. Once an address is set, then multiple writes to the corre- sponding data register are allowed. Address 0 is the default address on the first rising edge after the AAT3141 has been disabled. If data is presented on the first rising edge with no prior address, both data registers are simultaneously loaded. When EN/SET is held low for an amount of time greater than T OFF, the AAT3141 enters into shutdown mode and draws less than 1µA from VIN. Data and address registers are reset to 0 during shutdown. Table 2: AS2Cwire Serial Interface Addressing. AS2Cwire Serial Interface Timing Address EN/SET Rising Edges Data Register 0 33 1 & 2: D1-D4 1 34 1: D1-D3 2 35 2: D4 Address Data EN/SET 2 33 34 Address Data Reg 1 Data Reg 2 1 2 . . . n <= 32 0 1 n THI TLO TLAT TLAT

High Efficiency 1X/1.5X/2X Charge Pump for White LED Applications 3141.2007.03.1.3 13 LED Selection The AAT3141 is specifically intended for driving white LEDs. However, the device design will allow the AAT3141 to drive most types of LEDs with for- ward voltage specifications ranging from 1.0V to 4.3V. LED applications may include main and sub- LCD display backlighting, camera photo-flash appli- cations, color (RGB) LEDs, infrared (IR) diodes for remotes, and other loads benefiting from a controlled output current generated from a varying input volt- age. Since the D1 to D4 output current sources are matched with negligible voltage dependence, the LED brightness will be matched regardless of the specific LED forward voltage (V F) levels. In some instances (e.g., in high luminous output applications such as photo flash), it may be neces- sary to drive high-V F type LEDs. The low-dropout current sources in the AAT3141 make it capable of driving LEDs with forward voltages as high as 4.3V at full current from an input supply as low as 3.0V. Outputs can be paralleled to drive high-current LEDs without complication. Termination of Unused Current Source Outputs If any outputs (D1 to D4) are not used, they should be terminated by connecting the respective unused output directly to ground. This is required to assure correct charge pump mode operation. If a given unused output is not terminated to ground, it will appear to the respective output’s feedback control as an infinite impedance load and the unused con- stant current source will be set for a maximum volt- age. Although no current flows from the unused current source, the voltage sensed at that node could force the charge pump control to activate the charge pump when it is not necessary. To prevent this effect, simply connect the unused constant cur- rent source outputs to ground. Device Switching Noise Performance The AAT3141 operates at a fixed frequency of approximately 1MHz to control noise and limit har- monics that can interfere with the RF operation of cellular telephone handsets or other communica- tion devices. Back-injected noise appearing on the input pin of the charge pump is 20mV peak-to- peak, typically ten times less than inductor-based DC/DC boost converter white LED backlight solu- tions. The AAT3141 soft-start feature prevents noise transient effects associated with inrush cur- rents during start-up of the charge pump circuit. Power Efficiency and Device Evaluation The charge pump efficiency discussion in the follow- ing sections only accounts for efficiency of the charge pump section itself. Due to the unique circuit architecture and design of the AAT3141, it is very dif- ficult to measure efficiency in terms of a percent value comparing input power over output power. Since the AAT3141 outputs are pure constant cur- rent sources and typically drive individual loads, it is difficult to measure the output voltage for a given output (D1 to D4) to derive an overall output power measurement. For any given application, white LED forward voltage levels can differ, yet the out- put drive current will be maintained as a constant. This makes quantifying output power a difficult task when taken in the context of comparing to other white LED driver circuit topologies. A better way to quantify total device efficiency is to observe the total input power to the device for a given LED current drive level. The best white LED driver for a given applica- tion should be based on trade-offs of size, external component count, reliability, operating range, and total energy usage...not just % efficiency. The AAT3141 efficiency may be quantified under very specific conditions and is dependent upon the input voltage versus the output voltage seen across the loads applied to outputs D1 through D4 for a given constant current setting. Depending upon the case of V IN being greater than the specific voltage seen across the load on D1 through D4, the device will operate in load switch mode. If the voltage seen on the constant current source output is less than V IN, then the device will operate in 1.5X or 2X charge pump mode. Each of these modes will yield differ- ent efficiency values. Refer to the following two sec- tions for explanations of each operational mode. Load Switch Mode Efficiency The AAT3141 load switch mode is operational at all times and functions alone to enhance device power conversion efficiency when V IN is greater than volt- age across the load connected to the constant cur- rent source outputs. When in load switch mode,

High Efficiency 1X/1.5X/2X Charge Pump for White LED Applications 14 3141.2007.03.1.3 the voltage conversion efficiency is defined as out- put power divided by input power: The expression to define the ideal efficiency ( η) can be rewritten as: -or- Charge Pump Section Efficiency The AAT3141 contains a fractional charge pump which will boost the input supply voltage when V IN is less than the voltage required on the constant current source outputs. The efficiency ( η) can be simply defined as a linear voltage regulator with an effective output voltage that is equal to one and one half or two times the input voltage. Efficiency (η) for an ideal 1.5X charge pump can typically be expressed as the output power divided by the input power: In addition, with an ideal 1.5X charge pump, the output current may be expressed as 2/3 of the input current. The expression to define the ideal efficiency (η) can be rewritten as: -or- For a charge pump with an output of 5V and a nom- inal input of 3.5V, the theoretical efficiency is 95%. Due to internal switching losses and IC quiescent current consumption, the actual efficiency can be measured at 93%. These figures are in close agree- ment for output load conditions from 1mA to 100mA. Efficiency will decrease as load current drops below 0.05mA or when the level of V IN approaches VOUT. Refer to the Typical Characteristics section of this datasheet for measured plots of efficiency versus input voltage and output load current for the given charge pump output voltage options. Capacitor Selection Careful selection of the four external capacitors C IN, C1, C2, and COUT is important because they will affect turn-on time, output ripple, and transient per- formance. Optimum performance will be obtained when low equivalent series resistance (ESR) ceramic capacitors are used. In general, low ESR may be defined as less than 100m Ω. A value of 1µF for all four capacitors is a good starting point when choosing capacitors. If the LED current sources are only programmed for light current lev- els, then the capacitor size may be decreased. Capacitor Characteristics Ceramic composition capacitors are highly recom- mended over all other types of capacitors for use with the AAT3141. Ceramic capacitors offer many advantages over their tantalum and aluminum elec- trolytic counterparts. A ceramic capacitor typically has very low ESR, is lowest cost, has a smaller PCB footprint, and is non-polarized. Low ESR ceramic capacitors help maximize charge pump transient response. Since ceramic capacitors are non-polarized, they are not prone to incorrect con- nection damage. η = POUT PIN η = POUT = VOUT × IOUT = VOUT PIN VIN × IOUT VIN η(%) = 100 VOUT VIN η = POUT PIN η = POUT = VOUT × IOUT = VOUT PIN VIN × 1.5IOUT 1.5VIN η(%) = 100 VOUT 1.5VIN

High Efficiency 1X/1.5X/2X Charge Pump for White LED Applications 3141.2007.03.1.3 15 Equivalent Series Resistance ESR is an important characteristic to consider when selecting a capacitor. ESR is a resistance internal to a capacitor that is caused by the leads, internal connections, size or area, material compo- sition, and ambient temperature. Capacitor ESR is typically measured in milliohms for ceramic capac- itors and can range to more than several ohms for tantalum or aluminum electrolytic capacitors. Ceramic Capacitor Materials Ceramic capacitors less than 0.1µF are typically made from NPO or C0G materials. NPO and C0G materials have tight tolerance and are stable over temperature. Large capacitor values are composed of X7R, X5R, Z5U, or Y5V dielectric materials. Large ceramic capacitors, typically greater than 2.2µF, are often available in low-cost Y5V and Z5U dielectrics, but capacitors greater than 1µF are usu- ally not required for AAT3141 applications. Capacitor area is another contributor to ESR. Capacitors that are physically large will have a lower ESR when compared to an equivalent material smaller capacitor. These larger devices can improve circuit transient response when compared to an equal value capacitor in a smaller package size. Thermal Protection The AAT3141 has a thermal protection circuit that will shut down the charge pump if the die tempera- ture rises above the thermal limit, as is the case during a short-circuit of the CP pin. Charge Pump Compatibility The four-output AAT3141 is pin-compatible with the AAT3123, AAT3132, and AAT3113 in TSOPJW-12 packages. The AAT3141 offers an improved overall efficiency, wider operating range, and the ability to drive high-V F type LEDs at full current. The AAT3141 is well suited for battery-powered appli- cations using single-cell lithium-ion/polymer batter- ies and 3-series connected dry cells (3.6V).

High Efficiency 1X/1.5X/2X Charge Pump for White LED Applications 16 3141.2007.03.1.3 Advanced Analogic Technologies, Inc. 830 E. Arques Avenue, Sunnyvale, CA 94085 Phone (408) 737-4600 Fax (408) 737-4611 © Advanced Analogic Technologies, Inc. AnalogicTech cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in an AnalogicTech product. No circuit patent licenses, copyrights, mask work rights, or other intellectual property rights are implied. AnalogicTech reserves the right to make changes to their products or specifications or to discontinue any product or service with- out notice. Except as provided in AnalogicTech’s terms and conditions of sale, AnalogicTech assumes no liability whatsoever, and AnalogicTech disclaims any express or implied war- ranty relating to the sale and/or use of AnalogicTech products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right. In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. Testing and other quality control techniques are utilized to the extent AnalogicTech deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed. AnalogicTech and the AnalogicTech logo are trademarks of Advanced Analogic Technologies Incorporated. All other brand and product names appearing in this document are registered trademarks or trademarks of their respective holder s.

Ordering Information

Package Information

All dimensions in millimeters. Package Marking 1 Part Number (Tape and Reel)2 TSOPJW-12 LYXYY AAT3141ITP-T1 All AnalogicTech products are offered in Pb-free packaging. The term “Pb-free” means 0.20 + 0.10 - 0.05 0.055 ± 0.045 0.45 ± 0.15 7° NOM 4° ± 4° 3.00 ± 0.10 2.40 ± 0.10 2.85 ± 0.20 0.15 ± 0.05 0.9625 ± 0.0375 1.00 + 0.10 - 0.065

0.04 REF

0.010 2.75 ± 0.25 1. XYY = assembly and date code. 2. Sample stock is generally held on all part numbers listed in BOLD.