9008W8PXX62B30X CONEC

Document overview

  • Manufacturer or author: Provided By www.digicamel.com(free datasheet download site)
  • PDF pages: 2

Technical content

( 5 : 1 ) AA AA AA AA BB BB BB BB CC CC CC CC DD DD DD DD EE EE EE EE FF FF FF FF AA AA AA AA BB BB BB BB CC CC CC CC DD DD DD DD 9008W8PXX62B30X CONEC ABC dim. in mm RR RR date drawn THIS DRAW ING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH d-old norm appd. tolerance material: title: dwg no: DIN- sh: part no: namedate namedescriptionrev.DO NOT ALTER CAD DRAWING BY HAND scale: 15K1A1128 D-SUB COMBINATION MALE SEE NOTES Henneboel21.08.12

22.08.12 Fischer

with threaded inssert and hexlocking screw 2:1 (5:1) 9008W8PXX62B30X a Original SEE NOTE 14 14,24 -0,38 0,12 2,7n (8x) 55,3 - 0 0,25+ 4-40 UNC 4-40 UNC SEE NOTE 7 5,5 -0,18 0,12 SEALING COMPOUND RUBBER GASKET PLACED ON TOP SURFACE OF MALE INSULATOR 8,26 - 0,03 0,22+ AT ALL TIMES WATER RESISTANT CONNECTORS NOT IN USE SHOULD BE COVERED WITH A CONEC WATER RESISTANT CAP OR WATER TIGHT HOOD. 63,5\` 0,13 4,8SW 4,69,4 NOTES: 1. RECOMMENDED SOLDER INSTRUCTION SEE SHEET 2 2. METALSHELLS: STAINLESS STEEL 3. INSULATOR: PBT GF UL 94 V-0; GREEN 4. HIGH POWER CONTACTS 20A: COPPER ALLOY PLATING MATING AREA: GOLD FLASH over NICKEL PLATING TERMINATION: GOLD FLASH over NICKEL SOLDER CUP ACCEPTS CABLE AWG 12-14 5. THREADED INSERTS: COPPER ALLOY; min. 200µin TI N over 80µin NICKEL 6. COLLARS: COPPER ALLOY; min. 200µin TIN over 80 µin NICKEL 7. FRAME: PA GF UL 94 V-0; BLACK 8. RUBBER GASKET: TPE; BLACK 9. O-RING: SILICON; BLUE 10. HEXLOCKING SCREWS: STAINLESS STEEL 11. SEALING COMPOUND: PUR; BLUE 12. RECOMMENDED PANEL CUT-OUT ON SHEET 2 13. RECOMMENDED TORQUE FOR MOUNTING SCREW 35Ncm (3. 1 in.LB) / max. 40Ncm (3.5 in.LB) 14. CONNECTOR IS PART MARKED: 9008W8PXX62B30X CON EC ABC Directive 2002/95/EC RoHS compliant 3,8 -00,25 77,9 - 0 0,3+ 21,1 -00,3 10° O-RING POS. A1

dim. in mm RR RR date drawn THIS DRAW ING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH d-old norm appd. tolerance material: title: dwg no: DIN- sh: part no: namedate namedescriptionrev.DO NOT ALTER CAD DRAWING BY HAND scale: 15K1A1128 PANEL CUT-OUT see sheet1 Henneboel21.08.12 D-SUB COM. 8W8P MALE SOLDER CUP with threated insert and hexlocking screw 3:1 SEE SHEET 1 a Original Solder Instruction: 1. Cable should be prepared for soldering. The cable/wires must be pretinned. 2. Insert cable/wire into solder cup. 3. Operate the soldering iron at 350° C, 100 Watt max. and use a pencil tip. 4. Put tip to wire in solder cup. 5. After 1 second bring in solder. 6. Heat for 5 seconds longer. Do not heat contact more than 6 seconds in total. 7. Remove soldering iron. 8. Wait until solder gets rigid again. 9. Do not solder adjacent contacts consecutively, alternate position within the connector to minimize heat build up. 3,1 0,05 Ø (2x) 10°\ 1° 59,1\ 0,1 63,5\ 0,1 11,4 0,1 3,4 R \ 0,13 i 0,26 A i 0,26 A A B RECOMMENDED PANEL CUT-OUT