9003W3PXX62B30X CONEC

Document overview

  • Manufacturer or author: Provided By www.digicamel.com(free datasheet download site)
  • PDF pages: 2

Technical content

( 5 : 1 ) AA AA AA AA BB BB BB BB CC CC CC CC DD DD DD DD EE EE EE EE FF FF FF FF AA AA AA AA BB BB BB BB CC CC CC CC DD DD DD DD 9003W3PXX62B30X CONEC ABC dim. in mm RR RR date drawn THIS DRAW ING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH d-old norm appd. tolerance material: title: dwg no: DIN- sh: part no: namedate namedescriptionrev.DO NOT ALTER CAD DRAWING BY HAND scale: 15K1A1125 D-SUB COMBINATION MALE SEE NOTES Henneboel21.08.12

21.08.12 Fischer

with threaded insert and hexlocking screw 2:1 (5:1) 9003W3PXX62B30X a Original O-RING SEE NOTE 14 14,23 -0,38 0,12 5,5 -0,18 0,12 SEALING COMPOUND 4-40 UNC SEE NOTE 8 4,8SW 25,17 - 0,05 0,2+ 10° 2,7n (3x) 8,26 - 0,03 0,22+ RUBBER GASKET PLACED ON TOP SURFACE OF MALE INSULATOR 33,3 - 0,1 0,15+ 4-40 UNC 9,4 4,6 NOTES: 1. RECOMMENDED SOLDER INSTRUCTION SEE SHEET 2 2. METALSHELLS: STAINLESS STEEL 3. INSULATOR: PBT GF UL 94 V-0, GREEN 4. HIGH POWER CONTACTS 20A: COPPER ALLOY PLATING MATING AREA: GOLD FLASH over NICKEL PLATING TERMINATION SIDE: GOLD FLASH over NICKEL SOLDER CUP ACCEPTS CABLE AWG 12-14 5. THREADED INSERTS: COPPER ALLOY; min. 200µin TIN over 80µin NICKEL 6. COLLARS: COPPER ALLOY; min. 200µin TIN over 80µin NICKEL 7. HEXLOCKING SCREWS: STAINLESS STEEL 8. FRAME: PA GF UL 94 V-0; BLACK 9. O-RING: SILICON; BLUE 10. SEALING COMPOUND: PUR; BLUE 11. RUBBER GASKET: TPE; BLACK 12. RECOMMENDED PANEL CUT-OUT ON SHEET 2 13. RECOMMENDED TORQUE FOR MOUNTING SCREW 14. CONNECTOR IS PART MARKED: 9003W3PXX62B30X CONEC ABC AT ALL TIMES WATER RESISTANT CONNECTORS NOT IN USE SHOULD BE COVERED WITH A CONEC WATER RESISTANT CAP OR WATER TIGHT HOOD. Directive 2002/95/EC RoHS compliant 3,8 -00,25 47,7 - 0 0,3+ 21,1 -00,3

dim. in mm RR RR date drawn THIS DRAW ING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH d-old norm appd. tolerance material: title: dwg no: DIN- sh: part no: namedate namedescriptionrev.DO NOT ALTER CAD DRAWING BY HAND scale: 15K1A1125 RECOMMENDED PANEL CUT-OUT SEE SHEET 1 Henneboel21.08.12 D-SUB COMB. MALE 3W3P SOLDER CUP with threaded insert and hexlocking screw 3:1 SEE SHEET 1 a Original RECOMMENDED PANEL CUT-OUT Solder Instruction 1. Cable should be prepared for soldering. The cable/wires must be pretinned. 2. Insert cable/wire into solder cup. 3. Operate the soldering iron at 350° C, 100 Watt max. and use a pencil tip. 4. Put tip to wire in solder cup. 5. After 1 second bring in solder. 6. Heat for 5 seconds longer. Do not heat contact more than 6 seconds in total. 7. Remove soldering iron. 8. Wait until solder gets rigid again. 9. Do not solder adjacent contacts consecutively, alternate position within the connector to minimize heat build up. 3,4 R 0,13 11,4 0,1 28,8\ 0,1 3,1 0,05 n (2x) i 0,26 B i 0,26 A 10°\ 1° 33,3\` 0,1 B A