UTG6-1619SN ETC2

Document overview

  • Manufacturer or author: Provided By www.digicamel.com(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 20

Technical content

Datasheet sections

  • 1 Internal block diagram and pi n configuration
  • 2 Electrical ratings
  • 2.1 Absolute maximum ratings
  • 2.2 Thermal data
  • 3 Electrical characteristics
  • 3.1 Control part
  • 3.1.1 NTC thermistor
  • 3.2 Waveforms definitions
  • 4 Applications information
  • 4.1 Recommendations
  • 5 Package mechanical data
  • 6 Revision history

Features

 IPM 14 A, 600 V 3-phase IGBT inverter bridge including control ICs for gate driving and free- wheeling diodes  Short-circuit rugged IGBTs  V CE(sat) negative temperature coefficient  3.3 V, 5 V, 15 V CMOS/TTL inputs comparators with hysteresis and pull down / pull up resistors  Undervoltage lockout  Internal bootstrap diode  Interlocking function  Shut down function  DBC substrate leading to low thermal resistance  Isolation rating of 2500 Vrms/min  4.7 k NTC for temperature control  UL Recognized: UL1557 file E81734

Applications

 3-phase inverters for motor drives  Home appliances, such as washing machines, refrigerators, air conditioners and sewing machines

Description

This intelligent power module provides a compact, high performance AC motor drive in a simple, rugged design. Combining ST proprietary control ICs with the most advanced short-circuit- rugged IGBT system technology, this device is ideal for 3-phase inverters in applications such as home appliances and air conditioners. SLLIMM™ is a trademark of STMicroelectronics. SDIP-25L Table 1. Device summary

1 Internal block diagram and pin configuration

Figure 1. Internal block diagram

Figure 2. Pin layout (bottom view) Table 2. Pin description

8 GND Ground

10 HIN V High side logic input for V phase

11 OUT W High side reference output for W phase

12 V boot W Bootstrap voltage for W phase

13 LIN W Low side logic input for W phase

14 HIN W High side logic input for W phase

15 SD Shut down logic input (active low)

16 T1 NTC thermistor terminal

18 W W phase output

19 P Positive DC input

21 V V phase output

22 P Positive DC input

24 U U phase output

25 P Positive DC input

2 Electrical ratings

2.1 Absolute maximum ratings

Table 3. Inverter part

  1. Applied between HINi, LINi and GND for i = U, V, W
  2. Calculated according to the iterative formula:
  3. Pulse width limited by max junction temperature

Table 4. Control part Table 5. Total system

2.2 Thermal data

Table 6. Thermal data

3 Electrical characteristics

TJ = 25 °C unless otherwise specified. the switching time of IGBT itself under the internally given gate driving condition. Table 7. Inverter part

  1. Applied between HINi, LINi and GND for i = U, V, W (LIN inputs are active-low).

3.1 Control part

Table 8. Low voltage power supply (VCC = 15 V unless otherwise specified) Table 9. Bootstrapped voltage (VCC = 15 V unless otherwise specified) Table 10. Logic inputs (VCC = 15 V unless otherwise specified)

3.1.1 NTC thermistor

Figure 7. NTC resistance vs. temperature Figure 8. NTC resistance vs. temperature (zoom) Table 13. NTC thermistor Symbol Parameter Test cond itions Min. Typ. Max. Unit.

3.2 Waveforms definitions

Figure 9. Dead time and interlocking waveforms definitions

4 Applications information

Figure 10. Typical application circuit

4.1 Recommendations

variation of the input signal level. internal 5 V regulator through a diode, is built-in for each low side input. MCU terminals without any opto-coupler is possible.  Each capacitor should be located as nearby the pins of IPM as possible.  Low inductance shunt resistors should be used for phase leg current sensing. pins will further improve performance. signal should be pulled up to 5 V / 3.3 V with an external resistor. Note: For further deta ils refer to AN3338. Table 14. Recommended operating conditions

5 Package mechanical data

specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark. Please refer to dedicated technical note TN0107 for mounting instructions. Table 15. SDIP-25L mechanical data

Figure 11. SDIP-25L drawing dimensions data

Figure 12. SDIP-25L shipping tube (dimensions are in mm.)

Figure 13. SDIP-25L shipping tube type B (dimensions are in mm.)

6 Revision history

Table 16. Document revision history 07-Mar-2011 1 Initial release. 14-Sep-2011 2 Update Section 3.1.1 on page 11. Modified: Min. and Max. value Table 4 on page 5. Added: Figure 13 on page 18. parameter Table 4 on page 5.