8205

8205 ALLEGRO

Document overview

• Manufacturer or author: Provided By www.digicamel.com(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 8

Technical content

— FOR REFERENCE ONLY Designed specifically to meet the requirement for extended opera- tion of battery-powered equipment such as cordless and cellular tele- phones, the A8205SLH voltage regulators offer the reduced dropout voltage and quiescent current essential for maximum battery life. Applicable also to palmtop computers and personal data assistants, these devices deliver a regulated output at up to 200 mA (transient), which is limited only by package power dissipation. Regulated output Other voltages, down to 2.0 volts, are available on special order. A PMOS pass element provides a typical dropout voltage of only 75 mV at 100 mA of load current. The low dropout voltage permits deeper battery discharge before output regulation is lost. Quiescent current does not increase significantly as the dropout voltage is ap- proached, an ideal feature in standby/resume power systems where data integrity is crucial. Regulator accuracy and excellent temperature characteristics are provided by a bandgap reference. The A8205SLH includes an ENABLE input to give the designer complete control over power up, standby, or power down. These devices are supplied in a thermally enhanced 5-lead small- outline plastic package similar to the SOT-23, and fitting the SC-74A footprint. All devices are rated for operation over a temperature range of -20°C to +85°C. FEATURES AND BENEFITS I High Efficiency Provides Extended Battery Life I 75 mV Typical Dropout Voltage at IO = 100 mA I 55 µA Typical Quiescent Current Less Than 1 µA “Sleep” Current I Low Output Noise I 200 mA Peak Output Current I Improved PSRR and Transient Performance

APPLICATIONS

I Cordless and Cellular Telephones I Personal Data Assistants I Personal Communicators I Palmtop Computers LOW-DROPOUT REGULATORS — HIGH EFFICIENCY Data Sheet 27468.20 Always order by complete part number, e.g., A8205SLH-xx , where “xx” is the required output voltage in tenths or “ADJ” for adjustable. ABSOLUTE MAXIMUM RATINGS Peak Output Current, Operating Temperature Range, Junction Temperature, TJ . . . . +150°C Storage Temperature Range, * Output current rating is limited by input voltage, duty cycle, and ambient temperature. Under any set of conditions, do not exceed a junction temperature of +150°C. See follow- ing pages. 8205 Dwg. PS-021-5 VR 2GND 3 NC OR ADJ* ENABLE 5IN OUT *NO CONNECTION (fixed regulators) or ADJUST (A8205SLH-ADJ only). PRELIMINARY INFORMATION (subject to change without notice) December 6, 1999

115 Northeast Cutoff, Box 15036

Worcester, Massachusetts 01615-0036 (508) 853-5000 FUNCTIONAL BLOCK DIAGRAM Copyright © 1999, 2000 Allegro MicroSystems, Inc. A8205SLH Maximum Allowable Average Output Current* with device mounted on 2.24" x 2.24" (56.9 mm x 56.9 mm) solder-coated copper-clad board in still air. Allowable Total Average (10 ms) Output Current in Milliamperes with TJ = 150°C, Duty Cycle = 100%† VI - VO 25°C 200 200 200 200 200 189 162 142 126 50°C 200 200 200 200 182 152 130 114 101 70°C 200 200 200 182 145 121 104 91 81 85°C 200 200 197 148 118 98 84 74 66 * Absolute maximum peak output current rating is 200 mA; absolute maximum input voltage is 7 V. † IO = (TJ – TA)/([VI – VO] RθJA x dc) = (150 – TA)/([VI – VO] x 220 x 1.00) Output current rating can be increased (to 200 mA maximum) by additional heat sinking or reducing the duty cycle. DRIVE BANDGAP REF. ERROR AMP Dwg. FS-012-6 BIAS ENABLE IN ENABLE OUT1 5

2 GND

(SUFFIX "-ADJ" ONLY) OTHERWISE NO CONNECTION (FIXED REG'S)

www.allegromicro.com ELECTRICAL CHARACTERISTICS at TA = +25°C, VE = VI (unless otherwise noted). Limits Characteristic Symbol Test Conditions Min. Typ. Max. Units Output Voltage V O VI ≥ VO(nom) + 1 V, 1 mA ≤ IO ≤ 150 mA*, reference specified VO(nom) — 0.0 ±1.5 % Output Volt. Temp. Coeff. a VO VI = 6 V, IO = 10 mA, TJ ≤ 125°C — 40 — ppm/ °C Line Regulation ∆VO(∆VI) VO(nom) + 1 V ≤ VI ≤ 7 V, IO = 3 mA — — ±1.5 % Load Regulation ∆VO(∆IO) VI = VO(nom) + 1 V, 1 mA ≤ IO ≤ 150 mA* — — ±1.5 % VI = 7 V, 1 mA ≤ IO ≤ 150 mA* — — ±1.5 % Dropout Voltage V Imin - VO IO = 100 mA — 75 200 mV Ground Terminal Current I GND VI = VO(nom) + 1 V, IO = 1 mA — 55 65 µA VI = VO(nom) + 1 V, IO = 150 mA* — 55 65 µA VI = 7 V, IO = 1 mA — 55 65 µA VI = 7 V, IO = 150 mA* — 55 65 µA IQ VI ≤ 7 V, VE ≤ 0.8 V, IO = 0 mA — — 1.0 µA ENABLE Input Voltage V EH VI ≥ VO(nom) + 1 V, Output ON 2.0 — — V VEL VI ≥ VO(nom) + 1 V, Output OFF — — 0.4 V ENABLE Input Current I E VE = VI = 7 V — — ±1.0 µA Internal Reference Voltage V REF — 1.26 — V ADJUST Input Current I ADJ A8205SLH-ADJ only — 0.10 — µA Rejection Ratio PSRR V I = VO(nom) + 1.5 V, Vi = 100 mV, IO = 30 mA, f = 60 Hz — 70 — dB Output Noise e n 10 Hz ≤ f ≤ 100 kHz, IO = 10 mA, CO = 10 µF — 0.5 — µV/√Hz Typical values are at TA = +25°C and are given for circuit design information only. * Pulse test (≤20 ms). See previous page for duty cycle limitations.

Worcester, Massachusetts 01615-0036 (508) 853-5000 APPLICATIONS INFORMATION Linear regulators require input and output capacitors in order to maintain over-all loop stability. The recommended minimum value for the input capacitor is 0.1 µF. The output capacitor is the dominant pole that provides the high-frequency compensa- tion required for over-all regulator loop stability. These devices are stable with as little as 1 µF. However, to ensure stable operation under all conditions and capacitor types, the recom- mended minimum value is 4.7 µF. The output capacitor may be partially distributed through the load circuits. However, at least 1 µF should be connected at the regulator using the shortest and widest foil pattern possible. The A8205SLH-ADJ requires an external voltage divider to set up the desired regulated output voltage between 2.0 V and 6.8 V I ≤ 7 V). The two resistors are chosen such that The resistor values are usually as high as possible to maintain high circuit efficiency, but R 2 should be less than 300 kΩ. Dwg. ES-015 ENABLE (ACTIVE HIGH) INPUT (7.0 V MAX) OUTPUT (2.0 V TO 6.8 V) 0.1 µF (MIN) 1 µF (MIN) (300 kΩ MAX) VR 23 1 Thermal Considerations These devices are intended to provide more than 150 mA of continuous current in a very small package. The table on page 2 of this data sheet gives the maximum allowable average output current for a worst-case printed circuit design (R θJA = 220°C/W with a minimum footprint). Performance improvement is easily accomplished with the addition of 1 square inch of copper at terminal 2 (R θJA = 170°C/W).

www.allegromicro.com THIS PAGE INTENTIONALLY LEFT BLANK

Worcester, Massachusetts 01615-0036 (508) 853-5000 THIS PAGE INTENTIONALLY LEFT BLANK

www.allegromicro.com Dimensions in Inches (for reference only) Dimensions in Millimeters (controlling dimensions) 0.018 0.012 Dwg. MA-010-15 in 0.0059 0.00 0.0079 0.0059 0.122 0.079 0.083 0.073 0.118 0.106 0.037 BSC 0.022 REF 0° TO 8°

0.0098 MIN

0.043 0.035 0.049 0.035 Dwg. MA-011-5 mm 0.70 1.00 2.40 0.95 Dwg. MA-011-5 in 0.028 0.039 0.095 0.037 NOTES: 1. Tolerances on package height and width represent allowable mold offsets. Dimensions given are measured at the widest point (parting line). 2. Exact body and lead configuration at vendor’s option within limits shown. 3. Height does not include mold gate flash. 4. Where no tolerance is specified, dimension is nominal. Dwg. MA-010-15 mm 0.15 0.00 0.20 0.15 3.10 2.90 2.10 1.85 3.00 2.70 0.95 BSC 0.55 REF 0.45 0.30 0° TO 8°

0.25 MIN

1.10 0.90 1.25 0.90

Worcester, Massachusetts 01615-0036 (508) 853-5000 The products described here are manufactured under one or more Allegro MicroSystems, Inc. reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the user is cautioned to verify that the information being relied upon is current. Allegro products are not authorized for use as critical components in life-support devices or systems without express written approval. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, Inc. assumes no responsi- bility for its use; nor for any infringement of patents or other rights of third parties which may result from its use.