8151227 FESTO

Document overview

  • PDF pages: 2

Technical content

Page 1

Semi-rotary drive DFPD-160-RP-90-RS55-F0710

Part number: 8151227

PDF page 1 diagram
PDF page 1 diagram

General operating condition

Data sheet

Feature Value
Size of valve actuator 160
Flange hole pattern F0710
Swivel angle 90 deg
End-position adjusting range at 0° -5 deg ... 5 deg
End-position adjusting range at nominal swivel angle -5 deg ... 5 deg
Depth shaft connection 24 mm
Standard connection for valve ISO 5211
Mounting position Any
Mode of operation Single-acting
Structural design Gear rack/pinion
Closing direction Clockwise closing
Symbol 00991266
Valve connection conforms to standard VDI/VDE 3845 (NAMUR)
Connection point for positioner and position sensor conforms to standard VDI/VDE 3845 size AA 1
Devices type according to VDMA 66413 Safety device
Safety function The safety function consists of the actuator switching to the defined safety switching position when the compressed air is switched off and the spring chamber is exhausted. This switching movement is achieved through the spring force of the spring assembl
Safety integrity level (SIL) Up to SIL 2 low demand mode up to SIL 3 in a redundant architecture up to SIL 1 high demand mode
Certified for safety function to ISO 13849 and IEC 61508 (SIL) Product can be used in safety-related parts of control systems up to SIL 2, low demand Product can be used in safety-related parts of control systems up to SIL 1, high demand up to SIL 3 in a redundant architecture
Burst pressure 24 bar
Operating pressure 0.2 MPa ... 0.8 MPa
Operating pressure 2 bar ... 8 bar
Operating pressure 29 psi ... 116 psi
Nominal operating pressure 0.55 MPa
Nominal operating pressure 5.5 bar
Nominal operating pressure 79.75 psi
Maritime classification See certificate
CE marking (see declaration of conformity) as per EU explosion protection directive (ATEX)

12/30/25 - Subject to change - Festo SE & Co. KG

1/2

Page 2

Feature Value
UKCA marking (see declaration of conformity) acc. to UK EX instructions
Explosion protection certification outside the EU EPL Db (GB) EPL Gb (GB)
Explosion prevention and protection Zone 1 (ATEX) Zone 1 (UKEX) Zone 2 (ATEX) Zone 21 (ATEX) Zone 21 (UKEX) Zone 22 (ATEX)
Certificate issuing authority DNV TAP00001CE TÜV Rheinland 968/V 1106.01/2023
ATEX category gas II 2G
ATEX category for dust II 2D
Type of ignition protection for gas Ex h IIC T4 Gb X
Type of (ignition) protection for dust Ex h IIIC T105°C Db X
Explosive ambient temperature -20°C <= Ta <= +80°C
Operating medium Compressed air as per ISO 8573-1:2010 [7:4:4]
Information on operating and pilot media Dew point min. 10 °C below the ambient temperature and temperature of medium Operation with oil lubrication possible (required for further use)
LABS (PWIS) conformity VDMA24364-B1/B2-L
Storage temperature -20 °C ... 60 °C
Ambient temperature -20 °C ... 80 °C
Torque at nominal operating pressure and 0° swivel angle 108.1 Nm
Torque at nominal operating pressure and 90° swivel angle 56.3 Nm
Note about the torque The actuator's operating torque must not be higher than the maximum permissible torque listed in ISO 5211, based on the size of the mounting flange and the coupling.
Spring return torque at 0° swivel angle 52.9 Nm
Spring return torque with 90° swivel angle 104.7 Nm
Air consumption at 6 bar per cycle 0°-nominal swivel angle-0° 5.9 l
Product weight 7110 g
Shaft connection T22
Pneumatic connection G1/4
Note on materials RoHS-compliant
Material of sub-base Wrought aluminum alloy, anodized
Cover material Die-cast aluminum, coated
Seals material NBR
Material of spring Spring steel
Housing material Aluminum, anodized
Material of piston Die-cast aluminum
Material of bearing POM
Cam material High-alloy stainless steel
Material of screws High-alloy stainless steel
Shaft material Steel, nickel-plated

12/30/25 - Subject to change - Festo SE & Co. KG

2/2