Download PDF74HC4052 PHILIPS
Document overview
- PDF pages: 27
Technical content
Page 1
INTEGRATED CIRCUITS
Page 2
FEATURES
- Wide analog input voltage range from −5 V to +5 V
- Low ON-resistance: – 80 Ω (typical) at VCC − VEE = 4.5 V – 70 Ω (typical) at VCC − VEE = 6.0 V – 60 Ω (typical) at VCC − VEE = 9.0 V
- Logic level translation: to enable 5 V logic to communicate with ±5 V analog signals
- Typical “break before make” built in
- Complies with JEDEC standard no. 7A
- ESD protection: – HBM EIA/JESD22-A114-B exceeds 2000 V – MM EIA/JESD22-A115-A exceeds 200 V.
- Specified from −40 °C to +85 °C and −40 °C to +125 °C.
APPLICATIONS
- Analog multiplexing and demultiplexing
- Digital multiplexing and demultiplexing
- Signal gating.
FUNCTION TABLE
DESCRIPTION
The 74HC4052 and 74HCT4052 are high-speed Si-gate CMOS devices and are pin compatible with the HEF4052B. They are specified in compliance with JEDEC standard no. 7A. The 74HC4052 and 74HCT4052 are dual 4-channel analog multiplexers or demultiplexers with common select logic. Each multiplexer has four independent inputs/outputs (pins nY0 to nY3) and a common input/output (pin nZ). The common channel select logics include two digital select inputs (pins S0 and S1) and an active LOW enable input (pin E). When pin E = LOW, one of the four switches is selected (low-impedance ON-state) with pins S0 and S1. When pin E = HIGH, all switches are in the high-impedance OFF-state, independent of pins S0
and S1. VCC and GND are the supply voltage pins for the digital control inputs (pins S0, S1, and E). The VCC to GND ranges are 2.0 V to 10.0 V for 74HC4052 and 4.5 V to 5.5 V for 74HCT4052. The analog inputs/outputs (pins nY0 to nY3 and nZ) can swing between VCC as a positive limit and VEE as a negative limit. VCC − VEE may not exceed 10.0 V. For operation as a digital multiplexer/demultiplexer, VEE is connected to GND (typically ground).
| Column 1 | Column 2 | Column 3 | Column 4 |
|---|---|---|---|
| INPUT(1) | CHANNEL BETWEEN | ||
| E | S1 | S0 | |
| L | L | L | nY0 and nZ |
| L | L | H | nY1 and nZ |
| L | H | L | nY2 and nZ |
| L | H | H | nY3 and nZ |
| H | X | X | none |
Note 1. H = HIGH voltage level L = LOW voltage level X = don’t care.
Page 3
QUICK REFERENCE DATA
VEE = GND = 0 V; Tamb = 25 °C; tr = tf = 6 ns.
| SYMBOL | PARAMETER | CONDITIONS | TYPICAL | UNIT | |
|---|---|---|---|---|---|
| 74HC4052 | 74HCT4052 | ||||
| t /t PZH PZL | turn-on time E or Sn to V os | C = 15 pF; R = 1 kΩ; L L V = 5 V CC | 28 | 18 | ns |
| t /t PHZ PLZ | turn-off time E or Sn to V os | C = 15 pF; R = 1 kΩ; L L V = 5 V CC | 21 | 13 | ns |
| C I | input capacitance | 3.5 | 3.5 | pF | |
| C PD | power dissipation capacitance per switch | notes 1 and 2 | 57 | 57 | pF |
| C S | maximum switch capacitance | independent (Y) | 5 | 5 | pF |
| common (Z) | 12 | 12 | pF |
Notes 1. CPD is used to determine the dynamic power dissipation (PD in µW). PD = CPD × VCC2 × fi × N + Σ[(CL + CS) × VCC2 × fo] where: fi = input frequency in MHz; fo = output frequency in MHz; CL = output load capacitance in pF; CS = maximum switch capacitance in pF; VCC = supply voltage in Volts; N = number of inputs switching; Σ[(CL + CS) × VCC2 × fo] = sum of the outputs. 2. For 74HC4052 the condition is VI = GND to VCC For 74HCT4052 the condition is VI = GND to VCC − 1.5 V.
ORDERING INFORMATION
| TYPE NUMBER | PACKAGE | ||||
|---|---|---|---|---|---|
| TEMPERATURE RANGE | PINS | PACKAGE | MATERIAL | CODE | |
| 74HC4052D | −40 °C to +125 °C | 16 | SO16 | plastic | SOT109-3 |
| 74HCT4052D | −40 °C to +125 °C | 16 | SO16 | plastic | SOT109-3 |
| 74HC4052DB | −40 °C to +125 °C | 16 | SSOP16 | plastic | SOT338-1 |
| 74HCT4052DB | −40 °C to +125 °C | 16 | SSOP16 | plastic | SOT338-1 |
| 74HC4052N | −40 °C to +125 °C | 16 | DIP16 | plastic | SOT38-9 |
| 74HCT4052N | −40 °C to +125 °C | 16 | DIP16 | plastic | SOT38-9 |
| 74HC4052PW | −40 °C to +125 °C | 16 | TSSOP16 | plastic | SOT403-1 |
| 74HC4052BQ | −40 °C to +125 °C | 16 | DHVQFN16 | plastic | SOT763-1 |
| 74HCT4052BQ | −40 °C to +125 °C | 16 | DHVQFN16 | plastic | SOT763-1 |
Page 4
PINNING
| PIN | SYMBOL | DESCRIPTION |
|---|---|---|
| 1 | 2Y0 | independent input or output |
| 2 | 2Y2 | independent input or output |
| 3 | 2Z | common input or output |
| 4 | 2Y3 | independent input or output |
| 5 | 2Y1 | independent input or output |
| 6 | E | enable input (active LOW) |
| 7 | V EE | negative supply voltage |
| 8 | GND | ground (0 V) |
| 9 | S1 | select logic input |
| 10 | S0 | select logic input |
| 11 | 1Y3 | independent input or output |
| 12 | 1Y0 | independent input or output |
| 13 | 1Z | common input or output |
| 14 | 1Y1 | independent input or output |
| 15 | 1Y2 | independent input or output |
| 16 | V CC | positive supply voltage |
Page 5
Page 6
LIMITING VALUES
In accordance with the Absolute Maximum Rating System (IEC 60134); voltages are referenced to VEE = GND (ground = 0 V); note 1.
| SYMBOL | PARAMETER | CONDITIONS | MIN. | MAX. | UNIT |
|---|---|---|---|---|---|
| V CC | supply voltage | −0.5 | +11.0 | V | |
| I IK | input diode current | V < −0.5 V or V > V + 0.5 V I I CC | − | ±20 | mA |
| I SK | switch diode current | V < −0.5 V or V > V + 0.5 V S S CC | − | ±20 | mA |
| I S | switch current | −0.5 V < V < V + 0.5 V S CC | − | ±25 | mA |
| I EE | V current EE | − | ±20 | mA | |
| I ; I CC GND | V or GND current CC | − | ±50 | mA | |
| T stg | storage temperature | −65 | +150 | °C | |
| P tot | power dissipation | T = −40 °C to +125 °C; note amb | − | 500 | mW |
| P S | power dissipation per switch | − | 100 | mW |
Notes 1. To avoid drawing VCC current out of pins nZ, when switch current flows in pins nYn, the voltage drop across the bidirectional switch must not exceed 0.4 V. If the switch current flows into pins nZ, no VCC current will flow out of pins nYn. In this case there is no limit for the voltage drop across the switch, but the voltages at pins nYn and nZ may not exceed VCC or VEE. 2. For DIP16 packages: above 70 °C derate linearly with 12 mW/K. For SO16 packages: above 70 °C derate linearly with 8 mW/K. For SSOP16 and TSSOP16 packages: above 60 °C derate linearly with 5.5 mW/K. For DHVQFN16 packages: above 60 °C derate linearly with 4.5 mW/K.
Page 7
RECOMMENDED OPERATING CONDITIONS
| SYMBOL | PARAMETER | CONDITIONS | 74HC4052 | 74HCT4052 | UNIT | ||||
|---|---|---|---|---|---|---|---|---|---|
| MIN. | TYP. | MAX. | MIN. | TYP. | MAX. | ||||
| V CC | supply voltage | see Figs 7 and 8 V −GND CC V −V CC EE | 2.0 2.0 | 5.0 5.0 | 10.0 10.0 | 4.5 2.0 | 5.0 5.0 | 5.5 10.0 | V V |
| V I | input voltage | GND | − | V CC | GND | − | V CC | V | |
| V S | switch voltage | V EE | − | V CC | V EE | − | V CC | V | |
| T amb | operating ambient temperature | see DC and AC characteristics per device | −40 | +25 | +85 | −40 | +25 | +85 | °C |
| −40 | − | +125 | −40 | − | +125 | °C | |||
| t, t r f | input rise and fall times | V = 2.0 V CC | − | 6.0 | 1000 | − | 6.0 | 500 | ns |
| V = 4.5 V CC | − | 6.0 | 500 | − | 6.0 | 500 | ns | ||
| V = 6.0 V CC | − | 6.0 | 400 | − | 6.0 | 500 | ns | ||
| V = 10.0 V CC | − | 6.0 | 250 | − | 6.0 | 500 | ns |
Page 8
DC CHARACTERISTICS
Family 74HC4052 Vis is the input voltage at pins nYn or nZ, whichever is assigned as an input; Vos is the output voltage at pins nZ or nYn, whichever is assigned as an output; voltages are referenced to GND (ground = 0 V).
| SYMBOL | PARAMETER | TEST CONDITIONS | MIN. | TYP. | MAX. | UNIT | ||
|---|---|---|---|---|---|---|---|---|
| OTHER | V (V) CC | V (V) EE | ||||||
| T = −40 °C to +85 °C; note 1 amb | ||||||||
| V IH | HIGH-level input voltage | 2.0 | − | 1.5 | 1.2 | − | V | |
| 4.5 | − | 3.15 | 2.4 | − | V | |||
| 6.0 | − | 4.2 | 3.2 | − | V | |||
| 9.0 | − | 6.3 | 4.7 | − | V | |||
| V IL | LOW-level input voltage | 2.0 | − | − | 0.8 | 0.5 | V | |
| 4.5 | − | − | 2.1 | 1.35 | V | |||
| 6.0 | − | − | 2.8 | 1.8 | V | |||
| 9.0 | − | − | 4.3 | 2.7 | V | |||
| I LI | input leakage current | V = V or GND I CC | 6.0 | 0 | − | − | ±1.0 | µA |
| 10.0 | 0 | − | − | ±2.0 | µA | |||
| I S(OFF) | analog switch OFF-state current | V = V or V IL; I IH V S= V −V EE; see Fig.9 CC per channel all channels | 10.0 10.0 | 0 0 | − − | − − | ±1.0 ±2.0 | µA µA |
| I S(ON) | analog switch ON-state current | V = V or V IL; I IH V S= V −V EE; see Fig.10 CC | 10.0 | 0 | − | − | ±2.0 | µA |
| I CC | quiescent supply current | V = V or GND; I CC V = V or V CC; is EE V = V or V os CC EE | 6.0 | 0 | − | − | 80.0 | µA |
| 10.0 | 0 | − | − | 160.0 | µA |
Page 9
| SYMBOL | PARAMETER | TEST CONDITIONS | MIN. | TYP. | MAX. | UNIT | ||
|---|---|---|---|---|---|---|---|---|
| OTHER | V (V) CC | V (V) EE | ||||||
| T = −40 °C to +125 °C amb | ||||||||
| V IH | HIGH-level input voltage | 2.0 | − | 1.5 | − | − | V | |
| 4.5 | − | 3.15 | − | − | V | |||
| 6.0 | − | 4.2 | − | − | V | |||
| 9.0 | − | 6.3 | − | − | V | |||
| V IL | LOW-level input voltage | 2.0 | − | − | − | 0.5 | V | |
| 4.5 | − | − | − | 1.35 | V | |||
| 6.0 | − | − | − | 1.8 | V | |||
| 9.0 | − | − | − | 2.7 | V | |||
| I LI | input leakage current | V = V or GND I CC | 6.0 | 0 | − | − | ±1.0 | µA |
| 10.0 | 0 | − | − | ±2.0 | µA | |||
| I S(OFF) | analog switch OFF-state current | V = V or V IL; I IH V S= V −V EE; see Fig.9 CC per channel all channels | 10.0 10.0 | 0 0 | − − | − − | ±1.0 ±2.0 | µA µA |
| I S(ON) | analog switch ON-state current | V = V or V IL; I IH V S= V −V EE; see Fig.10 CC | 10.0 | 0 | − | − | ±2.0 | µA |
| I CC | quiescent supply current | V = V or GND; I CC V = V or V CC; is EE V = V or V os CC EE | 6.0 | 0 | − | − | 160 | µA |
| 10.0 | 0 | − | − | 320.0 | µA |
Note 1. All typical values are measured at Tamb = 25 °C.
Page 10
Family 74HCT4052 Vis is the input voltage at pins nYn or nZ, whichever is assigned as an input; Vos is the output voltage at pins nZ or nYn, whichever is assigned as an output; voltages are referenced to GND (ground = 0 V).
| SYMBOL | PARAMETER | TEST CONDITIONS | MIN. | TYP. | MAX. | UNIT | ||
|---|---|---|---|---|---|---|---|---|
| OTHER | V (V) CC | V (V) EE | ||||||
| T = −40 °C to +85 °C; note 1 amb | ||||||||
| V IH | HIGH-level input voltage | 4.5 to 5.5 | − | 2.0 | 1.6 | − | V | |
| V IL | LOW-level input voltage | 4.5 to 5.5 | − | − | 1.2 | 0.8 | V | |
| I LI | input leakage current | V = V or GND I CC | 5.5 | 0 | − | − | ±1.0 | µA |
| I S(OFF) | analog switch OFF-state current | V = V or V IL; I IH V S= V −V EE; see Fig.9 CC per channel all channels | 10.0 10.0 | 0 0 | − − | − − | ±1.0 ±2.0 | µA µA |
| I S(ON) | analog switch ON-state current | V = V or V IL; I IH V S= V −V EE; see Fig.10 CC | 10.0 | 0 | − | − | ±2.0 | µA |
| I CC | quiescent supply current | V = V or GND; I CC V = V or V CC; is EE V = V or V os CC EE | 5.5 | 0 | − | − | 80.0 | µA |
| 5.0 | −5.0 | − | − | 160.0 | µA | |||
| ∆I CC | additional quiescent supply current per input | V = V −2.1 V; other inputs I CC at V or GND CC | 4.5 to 5.5 | 0 | − | 45 | 202.5 | µA |
| T = −40 °C to +125 °C amb | ||||||||
| V IH | HIGH-level input voltage | 4.5 to 5.5 | − | 2.0 | − | − | V | |
| V IL | LOW-level input voltage | 4.5 to 5.5 | − | − | − | 0.8 | V | |
| I LI | input leakage current | V = V or GND I CC | 5.5 | 0 | − | − | ±1.0 | µA |
| I S(OFF) | analog switch OFF-state current | V = V or V IL; I IH V S= V −V EE; see Fig.9 CC per channel all channels | 10.0 10.0 | 0 0 | − − | − − | ±1.0 ±2.0 | µA µA |
| I S(ON) | analog switch ON-state current | V = V or V IL; I IH V S= V −V EE; see Fig.10 CC | 10.0 | 0 | − | − | ±2.0 | µA |
| I CC | quiescent supply current | V = V or GND; I CC V = V or V CC; is EE V = V or V os CC EE | 5.5 | 0 | − | − | 160.0 | µA |
| 5.0 | −5.0 | − | − | 320.0 | µA | |||
| ∆I CC | additional quiescent supply current per input | V = V −2.1 V; other inputs I CC at V or GND CC | 4.5 to 5.5 | 0 | − | − | 220.5 | µA |
Note 1. All typical values are measured at Tamb = 25 °C.
Page 11
Page 12
Resistance RON for 74HC4052 and 74HCT4052 Vis is the input voltage at pins nYn or nZ, whichever is assigned as an input; see notes 1 and 2; see Fig.11.
| SYMBOL | PARAMETER | TEST CONDITIONS | MIN. | TYP. | MAX. | UNIT | |||
|---|---|---|---|---|---|---|---|---|---|
| OTHER | V (V) CC | V (V) EE | I (µA) S | ||||||
| T = −40 °C to +85 °C; note 3 amb | |||||||||
| R ON(peak) | ON-resistance (peak) | V = V to V EE; is CC V = V or V I IH IL | 2.0 | 0 | 100 | − | − | − | Ω |
| 4.5 | 0 | 1000 | − | 100 | 225 | Ω | |||
| 6.0 | 0 | 1000 | − | 90 | 200 | Ω | |||
| 4.5 | −4.5 | 1000 | − | 70 | 165 | Ω | |||
| R ON(rail) | ON-resistance (rail) | V = V EE; is V = V or V I IH IL | 2.0 | 0 | 100 | − | 150 | − | Ω |
| 4.5 | 0 | 1000 | − | 80 | 175 | Ω | |||
| 6.0 | 0 | 1000 | − | 70 | 150 | Ω | |||
| 4.5 | −4.5 | 1000 | − | 60 | 130 | Ω | |||
| V = V CC; is V = V or V I IH IL | 2.0 | 0 | 100 | − | 150 | − | Ω | ||
| 4.5 | 0 | 1000 | − | 90 | 200 | Ω | |||
| 6.0 | 0 | 1000 | − | 80 | 175 | Ω | |||
| 4.5 | −4.5 | 1000 | − | 65 | 150 | Ω | |||
| ∆R ON | maximum ON-resistance difference between any two channels | V = V to V EE; is CC V = V or V I IH IL | 2.0 | 0 | − | − | − | − | Ω |
| 4.5 | 0 | − | − | 9 | − | Ω | |||
| 6.0 | 0 | − | − | 8 | − | Ω | |||
| 4.5 | −4.5 | − | − | 6 | − | Ω | |||
| T = −40 °C to +125 °C amb | |||||||||
| R ON(peak) | ON-resistance (peak) | V = V to V EE; is CC V = V or V I IH IL | 2.0 | 0 | 100 | − | − | − | Ω |
| 4.5 | 0 | 1000 | − | − | 270 | Ω | |||
| 6.0 | 0 | 1000 | − | − | 240 | Ω | |||
| 4.5 | −4.5 | 1000 | − | − | 195 | Ω | |||
| R ON(rail) | ON-resistance (rail) | V = V EE; is V = V or V I IH IL | 2.0 | 0 | 100 | − | − | − | Ω |
| 4.5 | 0 | 1000 | − | − | 210 | Ω | |||
| 6.0 | 0 | 1000 | − | − | 180 | Ω | |||
| 4.5 | −4.5 | 1000 | − | − | 160 | Ω | |||
| V = V CC; is V = V or V I IH IL | 2.0 | 0 | 100 | − | − | − | Ω | ||
| 4.5 | 0 | 1000 | − | − | 240 | Ω | |||
| 6.0 | 0 | 1000 | − | − | 210 | Ω | |||
| 4.5 | −4.5 | 1000 | − | − | 180 | Ω |
Notes 1. For 74HC4052: VCC − GND or VCC − VEE = 2.0, 4.5, 6.0 and 9.0 V; for 74HCT4052: VCC − GND = 4.5 and 5.5 V, VCC − VEE = 2.0, 4.5, 6.0 and 9.0 V. 2. When supply voltages (VCC − VEE) near 2.0 V the analog switch ON-resistance becomes extremely non-linear. When using a supply of 2 V, it is recommended to use these devices only for transmitting digital signals. 3. All typical values are measured at Tamb = 25 °C.
Page 13
Page 14
AC CHARACTERISTICS
Type 74HC4052 GND = 0 V; tr = tf = 6 ns; CL = 50 pF.
| SYMBOL | PARAMETER | TEST CONDITIONS | MIN. | TYP. | MAX. | UNIT | ||
|---|---|---|---|---|---|---|---|---|
| OTHER | V (V) CC | V (V) EE | ||||||
| T = −40 °C to +85 °C; note 1 amb | ||||||||
| t /t PHL PLH | propagation delay V to V is os | R = ∞; see Fig.19 L | 2.0 | 0 | − | 14 | 75 | ns |
| 4.5 | 0 | − | 5 | 15 | ns | |||
| 6.0 | 0 | − | 4 | 13 | ns | |||
| 4.5 | −4.5 | − | 4 | 10 | ns | |||
| t /t PZH PZL | turn-on time E, Sn to V os | R = ∞; see Figs 20, L 22 and 21 | 2.0 | 0 | − | 105 | 405 | ns |
| 4.5 | 0 | − | 38 | 81 | ns | |||
| 6.0 | 0 | − | 30 | 69 | ns | |||
| 4.5 | −4.5 | − | 26 | 58 | ns | |||
| t /t PHZ PLZ | turn-off time E, Sn to V os | R = 1 kΩ; see Figs 20, L 22 and 21 | 2.0 | 0 | − | 74 | 315 | ns |
| 4.5 | 0 | − | 27 | 63 | ns | |||
| 6.0 | 0 | − | 22 | 54 | ns | |||
| 4.5 | −4.5 | − | 22 | 48 | ns | |||
| T = −40 °C to +125 °C amb | ||||||||
| t /t PHL PLH | propagation delay V to V is os | R = ∞; see Fig.19 L | 2.0 | 0 | − | − | 90 | ns |
| 4.5 | 0 | − | − | 18 | ns | |||
| 6.0 | 0 | − | − | 15 | ns | |||
| 4.5 | −4.5 | − | − | 12 | ns | |||
| t /t PZH PZL | turn-on time E, Sn to V os | R = ∞; see Figs 20, L 22 and 21 | 2.0 | 0 | − | − | 490 | ns |
| 4.5 | 0 | − | − | 98 | ns | |||
| 6.0 | 0 | − | − | 83 | ns | |||
| 4.5 | −4.5 | − | − | 69 | ns | |||
| t /t PHZ PLZ | turn-off time E, Sn to V os | R = 1 kΩ; see Figs 20, L 22 and 21 | 2.0 | 0 | − | − | 375 | ns |
| 4.5 | 0 | − | − | 75 | ns | |||
| 6.0 | 0 | − | − | 64 | ns | |||
| 4.5 | −4.5 | − | − | 57 | ns |
Note 1. All typical values are measured at Tamb = 25 °C.
Page 15
Type 74HCT4052 GND = 0 V; tr = tf = 6 ns; CL = 50 pF.
| SYMBOL | PARAMETER | TEST CONDITIONS | MIN. | TYP. | MAX. | UNIT | ||
|---|---|---|---|---|---|---|---|---|
| OTHER | V (V) CC | V (V) EE | ||||||
| T = −40 °C to +85 °C; note 1 amb | ||||||||
| t /t PHL PLH | propagation delay V to V is os | R = ∞; see Fig.19 L | 4.5 | 0 | − | 5 | 15 | ns |
| 4.5 | −4.5 | − | 4 | 10 | ns | |||
| t /t PZH PZL | turn-on time E, Sn to V os | R = 1 kΩ; see Figs 20, L 22 and 21 | 4.5 | 0 | − | 41 | 88 | ns |
| 4.5 | −4.5 | − | 28 | 60 | ns | |||
| t t PHZ PLZ | turn-off time E, Sn to V os | R = 1 kΩ; see Figs 20, L 22 and 21 | 4.5 | 0 | − | 26 | 63 | ns |
| 4.5 | −4.5 | − | 21 | 48 | ns | |||
| T = −40 °C to +125 °C amb | ||||||||
| t /t PHL PLH | propagation delay V to V is os | R = ∞; see Fig.19 L | 4.5 | 0 | − | − | 18 | ns |
| 4.5 | −4.5 | − | − | 12 | ns | |||
| t /t PZH PZL | turn-on time E, Sn to V os | R = 1 kΩ; see Figs 20, L 22 and 21 | 4.5 | 0 | − | − | 105 | ns |
| 4.5 | −4.5 | − | − | 72 | ns | |||
| t /t PHZ PLZ | turn-off time E, Sn to V os | R = 1 kΩ; see Figs 20, L 22 and 21 | 4.5 | 0 | − | − | 75 | ns |
| 4.5 | −4.5 | − | − | 57 | ns |
Note 1. All typical values are measured at Tamb = 25 °C.
Page 16
Type 74HC4052 and 74HCT4052 Recommended conditions and typical values; GND = 0 V; Tamb = 25 °C; CL = 50 pF. Vis is the input voltage at pins nYn or nZ, whichever is assigned as an input. Vos is the output voltage at pins nYn or nZ, whichever is assigned as an output.
| SYMBOL | PARAMETER | TEST CONDITIONS | TYP. | UNIT | |||
|---|---|---|---|---|---|---|---|
| OTHER | V is(p-p) (V) | V (V) CC | V (V) EE | ||||
| d sin | sine-wave distortion | f = 1 kHz; R = 10 kΩ; L see Fig.13 | 4.0 | 2.25 | −2.25 | 0.04 | % |
| 8.0 | 4.5 | −4.5 | 0.02 | % | |||
| f = 10 kHz; R = 10 kΩ; L see Fig.13 | 4.0 | 2.25 | −2.25 | 0.12 | % | ||
| 8.0 | 4.5 | −4.5 | 0.06 | % | |||
| α OFF(feedthr) | switch OFF signal feed-through | R = 600 Ω; f = 1 MHz; L see Figs 14 and 15 | note 1 | 2.25 | −2.25 | −50 | dB |
| 4.5 | −4.5 | −50 | dB | ||||
| α ct(s) | crosstalk between two switches/multiplexers | R = 600 Ω; f = 1 MHz; L see Fig.16 | note 1 | 2.25 | −2.25 | −60 | dB |
| 4.5 | −4.5 | −60 | dB | ||||
| V ct(p-p) | crosstalk voltage between control and any switch (peak-to-peak value) | R = 600 Ω; f = 1 MHz; E or Sn, L square-wave between V and CC GND, t = t = 6 ns; see Fig.17 r f | − | 4.5 | 0 | 110 | mV |
| 4.5 | −4.5 | 220 | mV | ||||
| f max | minimum frequency response (−3dB) | R = 50 Ω; see Figs 13 and 18 L | note 2 | 2.25 | −2.25 | 170 | MHz |
| 4.5 | −4.5 | 180 | MHz | ||||
| C S | maximum switch capacitance | independent (Y) | − | − | − | 5 | pF |
| common (Z) | − | − | − | 12 | pF |
Notes 1. Adjust input voltage Vis to 0 dBm level (0 dBm = 1 mW into 600 Ω). 2. Adjust input voltage Vis to 0 dBm level at Vos for 1 MHz (0 dBm = 1 mW into 50 Ω).
Page 17
Page 18
Page 19
AC WAVEFORMS
Page 20
tW
handbook, full pagewidth
amplitude
90% negative
VM
input pulse
10%
0 V
tTHL (tf)
tTLH (tr)
tTLH (tr)
tTHL (tf) amplitude
90% positive
VM
input pulse
10%
0 V
tW
MNB059
| Column 1 | Column 2 | Column 3 | Column 4 | Column 5 |
|---|---|---|---|---|
| FAMILY | AMPLITUDE | V M | t and t r f | |
| f ; PULSE WIDTH max | OTHER | |||
| 74HC4052 | V CC | 50 % | < 2 ns | 6 ns |
| 74HCT4052 | 3.0 V | 1.3 V | < 2 ns | 6 ns |
Fig.21 Input pulse definitions.
handbook, full pagewidth
VCC switch open
VCC Vis
RL
VI
VO
PULSE
D.U.T.
GENERATOR
CL
RT
GND VEE MNB058
| Column 1 | Column 2 | Column 3 |
|---|---|---|
| TEST | SWITCH | V is |
| t PZH | V EE | V CC |
| t PZL | V CC | V EE |
| t PHZ | V EE | V CC |
| t PLZ | V CC | V EE |
| other | open | pulse |
Definitions for test circuit: RL = load resistance CL = load capacitance including jig and probe capacitance. RT = termination resistance should be equal to the output impedance ZO of the pulse generator. tr = tf = 6 ns; when measuring fmax, there is no constraint to tr and tf with 50 % duty factor.
Fig.22 Test circuit for measuring AC performance.
Page 21
PACKAGE OUTLINES
DIP16: plastic dual in-line package; 16 leads (300 mil)
SOT38-9
ME
D
A2 A
A1
L
c
b1
e
w M
Z
(e1) MH
b
b2 9
16
pin 1 index
E
1
8
0 5 10 mm
scale
DIMENSIONS (mm dimensions are derived from the original inch dimensions)
| UNIT | A max. | A1 min. | A2 max. | b | b1 | b2 | c | D(1) | E(1) | e | e1 | L | ME | MH | w | Z(1) max. |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| mm | 4.32 | 0.38 | 3.56 | 1.65 1.40 | 0.51 0.41 | 1.14 0.76 | 0.36 0.20 | 19.3 18.8 | 6.45 6.24 | 2.54 | 7.62 | 3.81 2.92 | 8.23 7.62 | 9.40 8.38 | 0.254 | 0.76 |
| inches | 0.17 | 0.015 | 0.14 | 0.065 0.055 | 0.020 0.016 | 0.045 0.030 | 0.014 0.008 | 0.76 0.74 | 0.254 0.246 | 0.1 | 0.3 | 0.150 0.115 | 0.324 0.300 | 0.37 0.33 | 0.01 | 0.03 |
Note 1. Plastic or metal protrusions of 0.25 mm (0.01 inch) maximum per side are not included.
REFERENCES
OUTLINE
EUROPEAN
ISSUE DATE
VERSION
PROJECTION
IEC
JEDEC
JEITA
97-07-24
SOT38-9
03-03-12
Page 22
SO16: plastic small outline package; 16 leads; body width 3.9 mm; body thickness 1.47 mm
SOT109-3
D
E
A X
c
y
HE
v M A
Z
16
9
A2
A (A ) 3
A1
pin 1 index
θ Lp L
1
8
e
detail X
w M bp
0 2.5 5 mm scale
DIMENSIONS (inch dimensions are derived from the original mm dimensions)
| UNIT | A max. | A1 | A2 | A3 | bp | c | D(1) | E(1) | e | HE | L | Lp | v | w | y | Z(1) | θ |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| mm | 0 1.75 0 | .25 .10 | 1.55 1.40 | 0.25 | 0.49 0.36 | 0.25 0.19 | 10.0 9.8 | 4.0 3.8 | 1.27 | 6.2 5.8 | 1.05 | 1.0 0.4 | 0.25 | 0.25 | 0.1 | 0.7 0.3 | 8o 0o |
| inches | 0 0.069 0 | .010 .004 | 0.061 0.055 | 0.01 | 0.019 0.014 | 0.0100 0.0075 | 0.39 0.38 | 0.16 0.15 | 0.05 | 0.244 0.228 | 0.041 | 0.039 0.016 | 0.01 | 0.01 | 0.004 | 0.028 0.012 |
Note 1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included.
REFERENCES
OUTLINE
EUROPEAN
ISSUE DATE
VERSION
PROJECTION
IEC
JEDEC
JEITA
98-12-23
SOT109-3
MS-012AC
03-02-19
Page 23
SSOP16: plastic shrink small outline package; 16 leads; body width 5.3 mm
SOT338-1
D
E
A X
c
y
HE
v M A
Z
9
16
Q
A2
A (A )
A1
3
pin 1 index
θ Lp L
8
1
detail X
w M bp
e
0 2.5 5 mm
scale
DIMENSIONS (mm are the original dimensions)
| UNIT | A max. | A 1 | A 2 | A 3 | bp | c | D(1) | E (1) | e | H E | L | Lp | Q | v | w | y | Z(1) | θ |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| mm | 2 | 0.21 1 0.05 1 | .80 .65 | 0.25 | 0.38 0.25 | 0.20 0.09 | 6.4 6.0 | 5.4 5.2 | 0.65 | 7.9 7.6 | 1.25 | 1.03 0.63 | 0.9 0.7 | 0.2 | 0.13 | 0.1 | 1.00 0.55 | 8o 0o |
Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
REFERENCES
OUTLINE
EUROPEAN
ISSUE DATE
VERSION
PROJECTION
IEC
JEDEC
JEITA
99-12-27
SOT338-1
MO-150
03-02-19
Page 24
TSSOP16: plastic thin shrink small outline package; 16 leads; body width 4.4 mm
SOT403-1
E
A
D
X
c
y
HE
v M A
Z
9
16
Q (A )
A2
3 A
A1
pin 1 index
θ Lp L
1
8
detail X
w M bp
e
0 2.5 5 mm
scale
DIMENSIONS (mm are the original dimensions)
| UNIT | A max. | A1 | A2 | A3 | bp | c | D (1) | E (2) | e | HE | L | Lp | Q | v | w | y | Z(1) | θ |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| mm | 1.1 | 0.15 0.05 | 0.95 0.80 | 0.25 | 0.30 0.19 | 0.2 0.1 | 5.1 4.9 | 4.5 4.3 | 0.65 | 6.6 6.2 | 1 | 0.75 0.50 | 0.4 0.3 | 0.2 | 0.13 | 0.1 | 0.40 0.06 | 8o 0o |
Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included.
REFERENCES
OUTLINE
EUROPEAN
ISSUE DATE
VERSION
PROJECTION
IEC
JEDEC
JEITA
99-12-27
SOT403-1
MO-153
03-02-18
Page 25
DHVQFN16: plastic dual in-line compatible thermal enhanced very thin quad flat package; no leads;
SOT763-1
16 terminals; body 2.5 x 3.5 x 0.85 mm
A B
D
A A1
E
c
detail X
terminal 1 index area
C
terminal 1
e1
index area
y
y1 C
e
v M C A B
b
w M C
2
7
L
1
8
Eh
e
16
9
15
10
Dh
X
0
2.5
5 mm
scale
DIMENSIONS (mm are the original dimensions)
| UNIT | A(1) max. | A1 | b | c | D(1) | Dh | E(1) | Eh | e | e1 | L | v | w | y | y1 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| mm | 1 | 0.05 0.00 | 0.30 0.18 | 0.2 | 3.6 3.4 | 2.15 1.85 | 2.6 2.4 | 1.15 0.85 | 0.5 | 2.5 | 0.5 0.3 | 0.1 | 0.05 | 0.05 | 0.1 |
Note 1. Plastic or metal protrusions of 0.075 mm maximum per side are not included.
| Column 1 | Column 2 | Column 3 | Column 4 | Column 5 | Column 6 | Column 7 | Column 8 |
|---|---|---|---|---|---|---|---|
| OUTLINE VERSION | REFERENCES | EUROPEAN PROJECTION | ISSUE DATE | ||||
| IEC | JEDEC | JEITA | |||||
| SOT763-1 | - - - | MO-241 | - - - | 02-10-17 03-01-27 |
Page 26
DATA SHEET STATUS
| Column 1 | Column 2 | Column 3 | Column 4 |
|---|---|---|---|
| LEVEL | DATA SHEET STATUS(1) | PRODUCT STATUS(2)(3) | DEFINITION |
| I | Objective data | Development | This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice. |
| II | Preliminary data | Qualification | This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. |
| III | Product data | Production | This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). |
Notes 1. Please consult the most recently issued data sheet before initiating or completing a design. 2. The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com. 3. For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status.
DEFINITIONS
Short-form specification The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability.
Application information Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification.
DISCLAIMERS
Life support applications These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes Philips Semiconductors reserves the right to make changes in the products - including circuits, standard cells, and/or software - described or contained herein in order to improve design and/or performance. When the product is in full production
(status ‘Production’), relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no licence or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified.
Page 27
Philips Semiconductors – a worldwide company
Contact information
For additional information please visit http://www.semiconductors.philips.com.
Fax: +31 40 27 24825
For sales offices addresses send e-mail to: sales.addresses@www.semiconductors.philips.com.
SCA76
© Koninklijke Philips Electronics N.V. 2004
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights.
Printed in The Netherlands
R44/04/pp27
Date of release: 2004 Nov 11
Document order number: 9397 750 14189
