DATASHEET SEARCH SITE

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 17

Technical content

signals into sharply defined, jitter-free output signals. Table 1. Ordering information

Product data sheet Rev. 3 — 25 July 2011 2 of 17 NXP Semiconductors 74HC7541; 74HCT7541 Octal Schmitt trigger buffer/line driver; 3-state 4. Functional diagram 5. Pinning information

5.1 Pinning

Fig 1. Logic symbol Fig 2. IEC logic symbol aaa-000084 21 8Y0 OE1 OE2 aaa-000085 9 11 1 & EN Fig 3. Pin configuration DIP20, SO20 Fig 4. Pin configuration SSOP20, TSSOP20 74HC7541 74HCT7541 OE1 VCC A0 OE2 A1 Y0 A2 Y1 A3 Y2 A4 Y3 A5 Y4 A6 Y5 A7 Y6 GND Y7 aaa-000086 74HC7541 74HCT7541 OE1 VCC AO OE2 A1 Y0 A2 Y1 A3 Y2 A4 Y3 A5 Y4 A6 Y5 A7 Y6 GND Y7 aaa-000087

5.2 Pin description

[1] H = HIGH voltage level; L = LOW voltage level; X = don’t care; Z = high-impedance OFF-state. [1] The input and output voltage ratings may be exceeded if the input and output current ratings are observed. [2] For DIP20 packages: above 70 C the value of Ptot derates linearly with 12 mW/K. For SO20 packages: above 70 C the value of Ptot derates linearly with 8 mW/K. For SSOP20 and TSSOP20 packages: above 60 C the value of Ptot derates linearly with 5.5 mW/K. Table 2. Pin description Table 3. Functional table [1] Table 4. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V).

  1. Recommended operating conditions

Table 5. Recommended operating conditions Table 6. Static characteristics At recommended operating conditions; voltages are referenced to GND (ground = 0 V).

At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Table 7. Dynamic characteristics L = 50 pF; for test circuit see Figure 7.

[1] t pd is the same as tPLH and tPHL. ten is the same as tPZL and tPZH. tdis is the same as tPLZ and tPHZ. [2] t t is the same as tTHL and tTLH.  (CL  VCC2  fo) = sum of outputs. GND = 0 V; CL = 50 pF; for test circuit see Figure 7. Measurement points are given in Table 8. VOL and VOH are typical voltage output levels that occur with the output load.

Measurement points are given in Table 8. VOL and VOH are typical voltage output levels that occur with the output load. Table 8. Measurement points

Test data is given in Table 9. Table 9. Test data

  1. Transfer characteristics
  2. Transfer characteristics waveforms

Table 10. Transfer characteristics At recommended operating conditions; voltages are referenced to GND (ground = 0 V); see Figure 8 and Figure 9.

Product data sheet Rev. 3 — 25 July 2011 10 of 17 NXP Semiconductors 74HC7541; 74HCT7541 Octal Schmitt trigger buffer/line driver; 3-state 14. Package outline Fig 10. Package outline SOT146-1 (DIP20) UNIT A max. 1 2 b1 cD E e MHL REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm inches DIMENSIONS (inch dimensions are derived from the original mm dimensions) SOT146-1 99-12-27 03-02-13 A min. A max. b Z max.wMEe1 1.73 1.30 0.53 0.38 0.36 0.23 26.92 26.54 6.40 6.22 3.60 7.80 10.0 8.3 24.2 0.51 3.2 0.068 0.051 0.021 0.015 0.014 0.009 1.060 1.045 0.25 0.24 0.14 0.31 0.39 SC-603MS-001 MH c (e )1 ME A L seating plane w M e D Z b E pin 1 index 0 5 10 mm scale Note 1. Plastic or metal protrusions of 0.25 mm (0.01 inch) maximum per side are not included. (1)(1) (1) DIP20: plastic dual in-line package; 20 leads (300 mil) SOT146-1

Product data sheet Rev. 3 — 25 July 2011 11 of 17 NXP Semiconductors 74HC7541; 74HCT7541 Octal Schmitt trigger buffer/line driver; 3-state Fig 11. Package outline SOT163-1 (SO20) UNIT A max. A1 A2 A3 bp cD (1) E (1) (1)eH E LL p Q Zy w v θ REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm inches 2.65 0.3 0.1 2.45 2.25 0.49 0.36 0.32 0.23 13.0 12.6 7.6 7.4 1.27 10.65 10.00 1.1 1.0 0.9 0.4 8 o o 0.25 0.1 DIMENSIONS (inch dimensions are derived from the original mm dimensions) Note 1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included. 1.1 0.4 SOT163-1 w M bp detail X Z e D y 0.25 075E04 MS-013 pin 1 index 0.1 0.012 0.004 0.096 0.089 0.019 0.014 0.013 0.009 0.51 0.49 0.30 0.29 0.05 1.4 0.0550.419 0.394 0.043 0.039 0.035 0.0160.01 0.25 0.01 0.0040.043 0.0160.01 0 5 10 mm scale X θ AA1 HE Lp Q E c L v M A (A )3 A SO20: plastic small outline package; 20 leads; body width 7.5 mm SOT163-1 99-12-27 03-02-19

Product data sheet Rev. 3 — 25 July 2011 12 of 17 NXP Semiconductors 74HC7541; 74HCT7541 Octal Schmitt trigger buffer/line driver; 3-state Fig 12. Package outline SOT339-1 (SSOP20) UNIT A1 A2 A3 bp cD (1) E(1) eH E LL p Q (1)Z y w v θ REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm 0.21 0.05 1.80 1.65 0.38 0.25 0.20 0.09 7.4 7.0 5.4 5.2 0.65 7.9 7.6 0.9 0.7 0.9 0.5 o o0.131.25 0.2 0.1 DIMENSIONS (mm are the original dimensions) Note 1. Plastic or metal protrusions of 0.2 mm maximum per side are not included. 1.03 0.63 SOT339-1 MO-150 99-12-27 03-02-19 X w M θ A bp D HE Lp Q detail X E Z e c L v M A (A )3 A 11 0 20 11 y 0.25 pin 1 index 0 2.5 5 mm scale SSOP20: plastic shrink small outline package; 20 leads; body width 5.3 mm SOT339-1 A max.

Product data sheet Rev. 3 — 25 July 2011 13 of 17 NXP Semiconductors 74HC7541; 74HCT7541 Octal Schmitt trigger buffer/line driver; 3-state Fig 13. Package outline SOT360-1 (TSSOP20) UNIT A1 A2 A3 bp cD (1) E (2) (1)eH E LL p QZ y w v θ REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm 0.15 0.05 0.95 0.80 0.30 0.19 0.2 0.1 6.6 6.4 4.5 4.3 0.65 6.6 6.2 0.4 0.3 0.5 0.2 o o0.13 0.10.21 DIMENSIONS (mm are the original dimensions) Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included. 0.75 0.50 SOT360-1 MO-153 99-12-27 03-02-19 w M bp D Z e 0.25 11 0 20 11 pin 1 index θ AA1 Lp Q detail X L (A )3 HE E c v M A XA y 0 2.5 5 mm scale TSSOP20: plastic thin shrink small outline package; 20 leads; body width 4.4 mm SOT360-1 A max. 1.1

Table 11. Abbreviations Table 12. Revision history

  • The format of this data sheet has been redesigned to comply with the new identity guidelines of NXP Semiconductors.
  • Legal texts have been adapted to the new company name where appropriate.
  • Added type numbers 74HC7541PW and 74HCT7541PW (TSSOP20 package). 74HC_HCT7541_CNV v.2 19970917 Product specification - -

Product data sheet Rev. 3 — 25 July 2011 15 of 17 NXP Semiconductors 74HC7541; 74HCT7541 Octal Schmitt trigger buffer/line driver; 3-state 17. Legal information

17.1 Data sheet status

[1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com.

17.2 Definitions

Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification — The information and data provided in a Product data sheet shall define the specification of the product as agreed between NXP Semiconductors and its customer, unless NXP Semiconductors and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the NXP Semiconductors product is deemed to offer functions and qualities beyond those described in the Product data sheet.

17.3 Disclaimers

Limited warranty and liability — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use in automotive applications — This NXP Semiconductors product has been qualified for use in automotive applications. The product is not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product design. It is customer’s sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s applications or products, or the application or use by customer’s third party customer(s). Customer is responsible for doing all necessary testing for the customer’s applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customer’s third party customer(s). NXP does not accept any liability in this respect. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale — NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms , unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer’s general terms and conditions with regard to the purchase of NXP Semiconductors products by customer. No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification.

Product data sheet Rev. 3 — 25 July 2011 16 of 17 NXP Semiconductors 74HC7541; 74HCT7541 Octal Schmitt trigger buffer/line driver; 3-state Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from national authorities.

17.4 Trademarks

Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 18. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com

NXP Semiconductors 74HC7541; 74HCT7541 Octal Schmitt trigger buffer/line driver; 3-state © NXP B.V. 2011. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 25 July 2011 Document identifier: 74HC_HCT7541 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. 19. Contents