DATASHEET SEARCH SITE

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 32

Technical content

  1. General description The 74HC7403-Q100; 74HCT7403-Q100 is an expandable, First-In First-Out (FIFO) memory organized as 64 words by 4 bits. A guaranteed 15 MHz data-rate makes it ideal for high-speed applications. A higher data-rate can be obtained in applications where the status flags are not used (burst-mode). With separate controls for shift-in (SI) and shift-out (SO), reading and writing operations are completely independent, allowing synchronous and asynchronous data transfers. Additional controls include a master-reset input (MR), an output enable input (OE) and flags. The data-in-ready (DIR) and data-out-ready (DOR) flags indicate the status of the device. Inputs include clamp diodes that enable the use of current limiting resistors to interface inputs to voltages in excess of VCC. This product has been qualified to the Automotive Electronics Council (AEC) standard Q100 (Grade 1) and is suitable for use in automotive applications. 2. Features and benefits  Automotive product qualification in accordance with AEC-Q100 (Grade 1)  Specified from 40 C to +85 C and from 40 C to +125 C  Synchronous or asynchronous operation  30 MHz (typical) shift-in and shift-out rates  Readily expandable in word and bit dimensions  Pinning arranged for easy board layout: input pins directly opposite output pins  Input levels:  For 74HC7403-Q100: CMOS level  For 74HCT7403-Q100: TTL level  3-state outputs  Complies with JEDEC standard JESD7A  ESD protection:  MIL-STD-883, method 3015 exceeds 2000 V  HBM JESD22-A114F exceeds 2000 V  MM JESD22-A115-A exceeds 200 V (C = 200 pF, R = 0 )  Multiple package options 3. Applications  High-speed disc or tape controller  Communications buffer 74HC7403-Q100; 74HCT7403-Q100 4-bit x 64-word FIFO register; 3-state Rev. 1 — 21 September 2012 Product data sheet

Table 1. Ordering information

xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx Product data sheet Rev. 1 — 21 September 2012 3 of 32 NXP Semiconductors 74HC7403-Q100; 74HCT7403-Q100 4-bit x 64-word FIFO register; 3-state LOW on S input of the flip-flops FS, FB and FP set Q output to HIGH independent of state on R input LOW on R input of FF1 to FF64 sets Q output to LOW independent of state on S input Fig 4. Logic diagram /g80/g86/g69/g20/g20/g27 /g11/g20/g12 /g53 /g54/g52 /g41/g54 /g23 /g47/g36/g55/g38/g43/g40/g54 /g38/g47/g38/g47 /g39/g44/g53 /g54/g44 /g48/g53 /g11/g21/g12 /g53 /g54/g52 /g41/g41/g20 /g11/g21/g12 /g53 /g54/g52 /g41/g41/g21 /g53/g52 /g53/g52 /g53 /g54/g52 /g41/g41/g22 /g87/g82 /g41/g41/g25/g22 /g53/g52 /g25/g20/g3/g91 /g53 /g54/g52 /g41/g41/g25/g23 /g53/g52 /g11/g21/g12 /g53 /g54/g52 /g41/g37 /g11/g20/g12 /g53 /g54/g52 /g41/g51 /g11/g20/g12/g53 /g54/g50 /g39/g50/g53 /g50/g40 /g83/g82/g86/g76/g87/g76/g82/g81/g3/g20 /g23 /g47/g36/g55/g38/g43/g40/g54 /g38/g47/g38/g47 /g83/g82/g86/g76/g87/g76/g82/g81/g3/g21 /g23 /g47/g36/g55/g38/g43/g40/g54 /g38/g47/g38/g47 /g83/g82/g86/g76/g87/g76/g82/g81/g3/g22/g3/g87/g82/g3/g25/g22 /g23 /g47/g36/g55/g38/g43/g40/g54 /g38/g47/g38/g47 /g83/g82/g86/g76/g87/g76/g82/g81/g3/g25/g23 /g22/g16/g54/g55/g36/g55/g40 /g50/g56/g55/g51/g56/g55 /g37/g56/g41/g41/g40/g53 /g39/g19 /g39/g20 /g39/g26 /g39/g27 /g52/g19 /g52/g20 /g52/g26 /g52/g27

6.1 Pinning

6.2 Pin description

HIGH indicates a FIFO which can receive data. Table 2. Pin description

(DOR = LOW). When SO and DOR are HIGH, data is available at the outputs (Q0 to Q3).

7.1 Expanded format

be cascaded. Both parallel and serial expansion is possible. (see Figure 18). Serial expansion is only possible with typical devices.

7.1.1 Parallel expension

7.1.2 Serial expension

  • Tying the data outputs of the first device to the data inputs of the second device.
  • Connecting the DOR pin of the first device to the SI pin of the second device.
  • Connecting the SO pin of the first device to the DIR pin of the second device. 8. Limiting values [1] For SO16 packages: above 70 C the value of Ptot derates linearly with 8 mW/K.

Table 3. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V).

  1. Recommended operating conditions

Table 4. Recommended operating conditions Table 5. Static characteristics At recommended operating conditions; voltages are referenced to GND (ground = 0 V).

At recommended operating conditions; voltages are referenced to GND (ground = 0 V).

Table 6. Dynamic characteristics Voltages are referenced to GND (ground = 0 V); CL = 50 pF unless otherwise specified; for test circuit see Figure 17.

Table 6. Dynamic characteristics …continued Voltages are referenced to GND (ground = 0 V); CL = 50 pF unless otherwise specified; for test circuit see Figure 17.

Voltages are referenced to GND (ground = 0 V); CL = 50 pF unless otherwise specified; for test circuit see Figure 17.

Product data sheet Rev. 1 — 21 September 2012 13 of 32 NXP Semiconductors 74HC7403-Q100; 74HCT7403-Q100 4-bit x 64-word FIFO register; 3-state 12. Waveforms Measurement points are given in Table 7. VOL and VOH are typical voltage output levels that occur with the output load. Shifting in sequence FIFO empty to FIFO full (1) DIR initially HIGH; FIFO is prepared for valid data (2) SI set HIGH; data loaded into input stage (3) DIR goes LOW; input stage “busy” (4) SI set LOW; data from first location “ripple through” (5) DIR goes HIGH; status flag indica tes FIFO prepared for additional data (6) Repeat process to load 2 nd word through to 64th word into FIFO; DIR remains LOW; with attempt to shift into full FIFO, no data transfer occurs. Fig 6. Propagation delay SI input to DIR output, the SI pulse width and the SI maximum frequency /g80/g74/g68/g25/g24/g28 /g20/g18/g3/g73/g80 /g68 /g91 /g20/g86/g87/g3/g90/g82/g85/g71/g21/g81/g71/g3/g90/g82/g85/g71/g25/g23/g87/g75/g3/g90/g82/g85/g71 /g54/g44/g3/g3/g44/g49/g51/g56/g55 /g39/g81/g3/g44/g49/g51/g56/g55 /g39/g44/g53/g3/g3/g50/g56/g55/g51/g56/g55 /g57/g48/g57/g48 /g87/g90 /g87/g51/g47/g43 /g87/g51/g43/g47 /g11/g22/g12 /g11/g24/g12 /g11/g21/g12 /g11/g25/g12 /g11/g26/g12 /g11/g23/g12 /g11/g20/g12

Product data sheet Rev. 1 — 21 September 2012 14 of 32 NXP Semiconductors 74HC7403-Q100; 74HCT7403-Q100 4-bit x 64-word FIFO register; 3-state Measurement points are given in Table 7. VOL and VOH are typical voltage output levels that occur with the output load. With FIFO full; SI held HIGH in anticipation of empty location (1) FIFO is initially full, shift-in is held HIGH (2) SO pulse; data in output stage is unloaded, “bubble-up” process of empty location begins (3) DIR HIGH; when empty location reaches input stage, flag indicates that FIFO is prepared for data input (4) DIR returns to LOW; data returns to LOW; data shift- in to empty location is complete, FIFO is full again (5) SI set LOW; necessary to complete shift-in process, DIR remains LOW, because FIFO is full Fig 7. Bubble-up delay SO input to DIR output and the DIR pulse width. /g54/g44/g3/g3/g44/g49/g51/g56/g55 /g80/g74/g68/g25/g25/g19 /g39/g44/g53/g3/g3/g50/g56/g55/g51/g56/g55 /g69/g88/g69/g69/g79/g72/g3/g16/g3/g88/g83 /g71/g72/g79/g68/g92 /g54/g50/g3/g3/g44/g49/g51/g56/g55 /g57/g48 /g57/g48 /g57/g48 /g87/g58/g87/g51/g47/g43 /g11/g22/g12 /g11/g24/g12 /g11/g21/g12 /g11/g23/g12 /g11/g20/g12

Product data sheet Rev. 1 — 21 September 2012 15 of 32 NXP Semiconductors 74HC7403-Q100; 74HCT7403-Q100 4-bit x 64-word FIFO register; 3-state Measurement points are given in Table 7. VOL and VOH are typical voltage output levels that occur with the output load. Master reset applied with FIFO full (1) DIR LOW; output ready HIGH; assume that FIFO is full (2) MR pulse LOW; clears FIFO (3) DIR goes HIGH; flag indicates input prepared for valid data (4) DOR goes LOW; flag indicates FIFO empty (5) Qn outputs go LOW (only last bit is reset) Fig 8. Propagation delay MR input to DIR output, DOR output and Qn outputs and the MR pulse width. /g39/g44/g53/g3/g3/g50/g56/g55/g51/g56/g55 /g48/g53/g3/g3/g44/g49/g51/g56/g55 /g80/g74/g68/g25/g25/g27 /g52/g81/g3/g50/g56/g55/g51/g56/g55 /g39/g50/g53/g3/g3/g50/g56/g55/g51/g56/g55 /g57/g48 /g57/g48 /g57/g48 /g87/g58 /g87/g51/g47/g43 /g87/g51/g43/g47 /g87/g51/g43/g47 /g11/g22/g12 /g11/g24/g12 /g11/g21/g12 /g11/g23/g12 /g11/g20/g12

Product data sheet Rev. 1 — 21 September 2012 16 of 32 NXP Semiconductors 74HC7403-Q100; 74HCT7403-Q100 4-bit x 64-word FIFO register; 3-state Measurement points are given in Table 7. VOL and VOH are typical voltage output levels that occur with the output load. (1) DOR HIGH; no data transfer in progress, valid data is present at the output stage (2) SO set HIGH; result in DOR going LOW (3) DOR goes LOW; output stage “busy” (4) SO set LOW; data in the input stage is unloaded, and new data replaces it as empty location “bubbles-up” to input stage (5) DOR goes HIGH; transfer process completed, valid dat a present at output after the specified propagation delay (6) Repeat process to unload the 3 rd through the 64th word from FIFO (7) DOR remains LOW; FIFO is empty Fig 9. Propagation delay SO input to DOR output, the SO pulse width and the SO maximum frequency. /g80/g74/g68/g25/g25/g20 /g54/g50/g3/g3/g44/g49/g51/g56/g55 /g52/g81/g3/g50/g56/g55/g51/g56/g55 /g3 /g39/g50/g53/g3/g3/g50/g56/g55/g51/g56/g55 /g20/g86/g87/g3/g3/g54/g50/g3/g83/g88/g79/g86/g72/g21/g81/g71/g3/g3/g54/g50/g3/g83/g88/g79/g86/g72/g25/g23/g87/g75/g3/g3/g54/g50/g3/g83/g88/g79/g86/g72 /g20/g86/g87/g3/g90/g82/g85/g71/g21/g81/g71/g3/g90/g82/g85/g71/g25/g23/g87/g75/g3/g90/g82/g85/g71 /g57/g48 /g57/g48 /g57/g48 /g87/g51/g43/g47 /g87/g51/g47/g43 /g20/g18/g73/g80/g68/g91 /g87/g58 /g11/g22/g12 /g11/g26/g12 /g11/g24/g12 /g11/g21/g12 /g11/g25/g12/g11/g23/g12 /g11/g20/g12

Product data sheet Rev. 1 — 21 September 2012 17 of 32 NXP Semiconductors 74HC7403-Q100; 74HCT7403-Q100 4-bit x 64-word FIFO register; 3-state Measurement points are given in Table 7. VOL and VOH are typical voltage output levels that occur with the output load. With FIFO empty; SO is held HIGH in anticipation (1) FIFO is initially empty. SO is held HIGH. (2) SI pulse; loads data into FIFO and initiates ripple through process (3) DOR flag signals the arrival of valid data at the output stage (4) Output transition; data arrives at output stage after the s pecified propagation delay between the rising and falling edge of the DOR pulse to the Qn output (5) DOR goes LOW; data shift-out is completed, FIFO is empty again (6) SO set LOW; necessary to complete shift-out process. DOR remains LOW, because FIFO is empty Fig 10. Ripple through delay SI input to DOR output, propagation delay DOR input to Qn outputs and the DOR pulse width /g54/g44/g3/g3/g44/g49/g51/g56/g55 /g80/g74/g68/g25/g24/g27 /g11/g22/g12 /g11/g24/g12 /g52/g81/g3/g50/g56/g55/g51/g56/g55 /g39/g50/g53/g3/g3/g50/g56/g55/g51/g56/g55 /g11/g21/g12 /g85/g76/g83/g83/g79/g72/g3/g87/g75/g85/g82/g88/g74/g75 /g71/g72/g79/g68/g92 /g11/g25/g12 /g11/g23/g12 /g54/g50/g3/g3/g44/g49/g51/g56/g55/g11/g20/g12 /g57/g48 /g57/g48 /g57/g48 /g87/g58/g87/g51/g47/g43 /g87/g51/g43/g47/g18/g87/g51/g47/g43 Measurement points are given in Table 7. VOL and VOH are typical voltage output levels that occur with the output load. Shift-in operation; high speed burst mode In the high-speed mode, the burst-in rate is determined by the minimum shift-in HIGH and shift-in LOW specifications. The DIR status flag is a “don’t care” condition, and a shift-in pulse can be applied regardless of the flag. An SI pulse which would overflow the storage capacity of the FIFO is ignored. Fig 11. Shift-in (SI) pulse wid th and maximum frequency (SI) /g80/g74/g68/g25/g25/g21 /g54/g44/g3/g3/g44/g49/g51/g56/g55 /g39/g81/g3/g44/g49/g51/g56/g55 /g39/g44/g53/g3/g3/g50/g56/g55/g51/g56/g55 /g57/g48 /g87/g58 /g20/g18/g73/g80/g68/g91

Product data sheet Rev. 1 — 21 September 2012 18 of 32 NXP Semiconductors 74HC7403-Q100; 74HCT7403-Q100 4-bit x 64-word FIFO register; 3-state Measurement points are given in Table 7. VOL and VOH are typical voltage output levels that occur with the output load. Shift-out operation; high speed burst mode In the high-speed mode, the burst-out rate is determined by the minimum shift-out HIGH and shift-out LOW specifications. The DOR flag is a “don’t care” condition, and an SO pulse can be applied without regard to the flag. Fig 12. Shift-in (SO ) pulse width and maximum frequency (SO) /g80/g74/g68/g25/g25/g22 /g54/g50/g3/g3/g44/g49/g51/g56/g55 /g52/g81/g3/g50/g56/g55/g51/g56/g55 /g3 /g39/g50/g53/g3/g3/g50/g56/g55/g51/g56/g55 /g57/g48 /g87/g58 /g20/g18/g73/g80/g68/g91 Measurement points are given in Table 7. VOL and VOH are typical voltage output levels that occur with the output load. The shaded areas indicate when the output is permitted to change for predictable output performance Fig 13. Set-up and hold times /g54/g44/g3/g3/g44/g49/g51/g56/g55 /g80/g74/g68/g25/g24/g26 /g39/g81/g3/g44/g49/g51/g56/g55 /g87/g75 /g87/g86/g88 /g87/g75 /g87/g86/g88 /g57/g48 /g57/g48 Measurement points are given in Table 7. VOL and VOH are typical voltage output levels that occur with the output load. Fig 14. Propagation delay shift-out input (SO ) to data outputs (Qn) and output transition time /g80/g74/g68/g25/g25/g23 /g54/g50/g3/g3/g3/g44/g49/g51/g56/g55 /g52/g81/g3/g50/g56/g55/g51/g56/g55 /g57/g48 /g57/g48 /g87/g51/g47/g43 /g87/g55/g47/g43 /g28/g19/g3/g8 /g20/g19/g3/g8 /g28/g19/g3/g8 /g20/g19/g3/g8 /g87/g55/g43/g47 /g87/g51/g43/g47

Measurement points are given in Table 7. VOL and VOH are typical voltage output levels that occur with the output load. Measurement points are given in Table 7. VOL and VOH are typical voltage output levels that occur with the output load. Table 7. Measurement points

Test data is given in Table 8. RT = Termination resistance should be equal to output impedance Zo of the pulse generator. CL = Load capacitance including jig and probe capacitance. Table 8. Test data

Product data sheet Rev. 1 — 21 September 2012 21 of 32 NXP Semiconductors 74HC7403-Q100; 74HCT7403-Q100 4-bit x 64-word FIFO register; 3-state 13. Application information Fig 18. Expanded FIFO (parallel and serial) for in creased word length; 8 bits wide x 64 n-bits /g80/g74/g68/g25/g27/g23 /g39/g44/g53 /g54/g44 /g39/g50/g53 /g54/g50 /g48/g53 /g50/g40 /g50/g40 /g39/g44/g53 /g54/g44 /g39/g50/g53 /g54/g50/g48/g53 /g26/g23/g19/g22 /g50/g40 /g39/g44/g53 /g54/g44 /g39/g50/g53 /g54/g50/g48/g53 /g26/g23/g19/g22 /g50/g40 /g39/g44/g53 /g54/g44 /g39/g50/g53 /g54/g50/g48/g53 /g26/g23/g19/g22 /g50/g40 /g39/g44/g53 /g54/g44 /g39/g50/g53 /g54/g50/g48/g53 /g26/g23/g19/g22 /g39/g19 /g39/g20 /g39/g21 /g39/g22 /g52/g22 /g52/g21 /g52/g20 /g52/g19 /g39/g19 /g39/g20 /g39/g21 /g39/g22 /g52/g22 /g52/g21 /g52/g20 /g52/g19 /g39/g19 /g39/g20 /g39/g21 /g39/g22 /g52/g22 /g52/g21 /g52/g20 /g52/g19 /g39/g19 /g39/g20 /g39/g21 /g39/g22 /g52/g22 /g52/g21 /g52/g20 /g52/g19 /g27/g16/g69/g76/g87 /g71/g68/g87/g68 /g27/g16/g69/g76/g87 /g71/g68/g87/g68 The 74HC7403-Q100; 74HCT7403-Q100 is easily expanded to increase word length. Composite DIR and DIR flags are formed with the addition of an AND gate. The basic operation and timing are identical to a single FIFO, with the exception of an added gate delay on the flags. Fig 19. Expanded FIFO for increased word length; 64 words x 10 bits /g80/g74/g68/g25/g26/g27 /g39/g44/g53 /g50/g40 /g54/g44 /g39/g50/g53 /g54/g50 /g48/g53 /g39/g81 /g52/g81/g23 /g23 /g26/g23/g19/g22 /g39/g44/g53 /g50/g40 /g54/g44 /g39/g50/g53 /g54/g50 /g48/g53 /g26/g23/g19/g22 /g39/g81 /g52/g81/g23/g23 /g39/g36/g55/g36/g3/g3/g44/g49/g51/g56/g55 /g38/g50/g48/g51/g50/g54/g44/g55/g40 /g39/g44/g53 /g41/g47/g36/g42 /g54/g44 /g48/g53 /g50/g40 /g54/g50 /g39/g36/g55/g36/g3/g3/g50/g56/g55/g51/g56/g55 /g38/g50/g48/g51/g50/g54/g44/g55/g40 /g39/g50/g53 /g41/g47/g36/g42 /g39/g36/g55/g36/g3/g3/g44/g49/g51/g56/g55 /g39/g36/g55/g36/g3/g3/g50/g56/g55/g51/g56/g55

Product data sheet Rev. 1 — 21 September 2012 22 of 32 NXP Semiconductors 74HC7403-Q100; 74HCT7403-Q100 4-bit x 64-word FIFO register; 3-state This circuit is only required if the SI input is constantly held HIGH, when the FIFO is empty and the automatic shift-in cycles are started or if the SO output is constantly held HIGH, when the FIFO is full and the automatic shift-out cycles are started (see Figure 7 and Figure 10). Fig 20. Expanded FIFO for increased word length /g80/g74/g68/g25/g27/g22 /g39/g44/g53 /g50/g40 /g54/g44 /g39/g50/g53 /g54/g50 /g48/g53 /g39/g81 /g52/g81/g23 /g26/g23/g19/g22 /g39/g44/g53 /g50/g40 /g54/g44 /g39/g50/g53 /g54/g50 /g48/g53 /g26/g23/g19/g22 /g39/g81 /g52/g81 /g54/g44 /g48/g53 /g50/g40 /g54/g50 /g70/g82/g80/g83/g82/g86/g76/g87/g72 /g39/g50/g53 /g70/g82/g80/g83/g82/g86/g76/g87/g72 /g39/g44/g53 /g23 /g23/g23 /g39/g52 /g38/g51 /g53 /g26/g23 /g52 /g39/g52 /g38/g51 /g52 /g39 /g52 /g38/g51 /g26/g23 /g52 /g39 /g52 /g38/g51 /g52/g53

Product data sheet Rev. 1 — 21 September 2012 23 of 32 NXP Semiconductors 74HC7403-Q100; 74HCT7403-Q100 4-bit x 64-word FIFO register; 3-state

13.1 Expanded format

Figure 21 shows two cascaded FIFOs providing a capacity of 128 words x 4 bits. Figure 22 shows the signals on the nodes of both FIFOs after the application of the SI pulse, when both FIFOs are initially empty. After a ripple through delay, data arrives at the output of FIFOA. Due to SOA being HIGH, a DORA pulse is generated. The requirements od SIB and DnB are satisfied by the DORA pulse width and the timing between the rising edge of DORA and QnA. After a second ripple through delay data arrives at the output of FIFOB. Figure 23 shows the signals on the nodes of both FIFOs after the application of the SOB pulse, when both FIFOs are initially full. After a bubble-up delay, a DIRB pulse is generated, which acts as a SOA pulse for FIFOA. One word is transferred from the output of FIFOA to the input of FIFOB. The requirements of the SOA pulse for FIFOA is satisfied by the pulse width of DORB. After a second bubble-up delay an empty space arrives at DnA, at which time DIRA goes HIGH. Figure 24 shows the waveforms at all external nodes of both FIFOs during a complete shift-in and shift-out sequence. The 74HC7403-Q100; 74HCT7403-Q100 is easily cascaded to increase word capacity without external circuitry. In cascaded format, all necessary communications are handled by the FIFOs. Figure 22 and Figure 23 demonstrate the communication timing between FIFOA and FIFOB. Figure 24 provides an overview of pulses and timing of two cascaded FIFOs, when shifted full and shifted empty again. Fig 21. Cascading for increased word capacity; 128 words x 4 bits /g80/g74/g68/g25/g26/g28 /g39/g44/g53/g36 /g50/g40 /g54/g44/g36 /g48/g53 /g39/g81/g36/g23 /g39/g44/g53 /g54/g44 /g39/g50/g53 /g54/g50 /g39/g36/g55/g36/g3/g3/g44/g49/g51/g56/g55 /g23 /g54/g50/g36 /g39/g50/g53/g36 /g52/g81/g36 /g26/g23/g19/g22 /g41/g44/g41/g50/g3/g3/g36 /g39/g44/g53/g37 /g50/g40 /g54/g44/g37 /g48/g53 /g39/g81/g37 /g23 /g54/g50/g37 /g39/g50/g53/g37 /g52/g81/g37/g26/g23/g19/g22 /g41/g44/g41/g50/g3/g3/g37 /g39/g36/g55/g36/g3/g3/g50/g56/g55/g51/g56/g55 /g50/g40 /g48/g53

Product data sheet Rev. 1 — 21 September 2012 24 of 32 NXP Semiconductors 74HC7403-Q100; 74HCT7403-Q100 4-bit x 64-word FIFO register; 3-state (1) FIFOA and FIFOB are initially empty, SO A held HIGH in anticipation of data (2) Load one word into FIFOA; SI pulse; applied. results in DIR pulse (3) Data-out A/ data-in B transition; valid data arrives at FIFOA output stage after a specified delay of the DOR flag, meeting data input set-up requirements of FIFOB. (4) DORA and SIB pulse HIGH; (ripple through delay after SIA LOW) data is unloaded from FIFOA as a result of the data output ready pulse, data is shifted into FIFOB (5) DIRB and SO A go LOW; flag indicates that input stage of FIFOB is busy, shift-out of FIFOA is complete (6) DIRB and SO A go HIGH automatically; the input stage of FIFOB is again able to receive data, SO is held HIGH in anticipation of additional data (7) DORB goes HIGH; (ripple through delay after SIB LOW) valid dat a is present one propagation delay later at the FIFOB output stage Fig 22. FIFO to FIFO communication; input timing under empty condition /g80/g74/g68/g25/g25/g25 /g11/g24/g12 /g11/g25/g12 /g11/g21/g12 /g85/g76/g83/g83/g79/g72/g3/g87/g75/g85/g82/g88/g74/g75 /g71/g72/g79/g68/g92 /g11/g20/g12 /g11/g23/g12 /g85/g76/g83/g83/g79/g72/g3/g87/g75/g85/g82/g88/g74/g75 /g71/g72/g79/g68/g92 /g11/g22/g12 /g11/g26/g12 /g57/g48 /g57/g48 /g57/g48 /g57/g48 /g57/g48 /g39/g44/g53/g36 /g54/g44/g36 /g39/g50/g53/g36/g18/g54/g44/g37 /g52/g81/g36/g18/g39/g81/g37 /g39/g50/g53/g37 /g52/g81/g37 /g39/g44/g53/g37/g18/g54/g50/g36

Product data sheet Rev. 1 — 21 September 2012 25 of 32 NXP Semiconductors 74HC7403-Q100; 74HCT7403-Q100 4-bit x 64-word FIFO register; 3-state (1) FIFOA and FIFOB initially full, SIB held HIGH in anticipati on of shifting in new data as an empty location bubbles-up (2) Unload one word from FIFOB; SO pulse applied, results in DOR pulse (3) DIRB and SO A pulse HIGH; (bubble-up delay after SOB LOW) data is loaded into FIFOB as a result of the DIR pulse, data is shifted out of FIFOA (4) DORA and SIB go LOW; flag indicates that the output stage of FIFOA is busy, shift-in of FIFOB is complete (5) DORA and SIB go HIGH; flag indicates that valid data is again av ailable at FIFOA output stage, SIB is held HIGH, awaiting bubble-up of empty location. (6) DIRA goes HIGH; (bubble-up delay after SO A LOW) an empty location is present at input stage of FIFOA Fig 23. FIFO to FIFO communication; output timing under full condition /g80/g74/g68/g25/g25/g26 /g11/g23/g12 /g11/g24/g12 /g11/g25/g12 /g11/g21/g12 /g69/g88/g69/g69/g79/g72/g3/g16/g3/g88/g83 /g71/g72/g79/g68/g92 /g69/g88/g69/g69/g79/g72/g3/g16/g3/g88/g83 /g71/g72/g79/g68/g92 /g11/g20/g12 /g11/g22/g12 /g57/g48 /g57/g48 /g57/g48 /g57/g48 /g57/g48 /g39/g50/g53/g37 /g54/g50/g37 /g39/g44/g53/g37/g18/g54/g50/g36 /g52/g81/g36/g18/g39/g81/g37 /g39/g44/g53/g36 /g39/g50/g53/g36/g18/g54/g44/g37

Product data sheet Rev. 1 — 21 September 2012 26 of 32 NXP Semiconductors 74HC7403-Q100; 74HCT7403-Q100 4-bit x 64-word FIFO register; 3-state

13.1.1 Sequence 1 (both FIFOs empty, starting SHIFT-IN process)

After an MR pulse has been applied, FIFOA and FIFOB are empty. The DOR flags of FIFOA and FIFOB go LOW due to no valid data being present at the outputs. The DIR flags are set HIGH due to the FIFOs being ready to accept data. SOB is held HIGH and two SIA pulses are applied (1). These pulses allow two data words to ripple through the output stage of FIFOA and the input stage of FIFIB (2). When data arrives at the output of FIFOB, a DORB pulse is generated (3). When SOB goes LOW, the first bit is shifted out and a second bit ripples through to the output after which DORB goes high (4).

13.1.2 Sequence 2 (FIFOB runs full)

After the MR pulse, a series of 64 SI pulses are applied. When 64 words are shifted in, DIRB remains LOW due to FIFOB being full (5). DORA goes LOW due to FIFOA being empty. See also Section 13.1.1 Fig 24. Waveforms showing the functionality and intercommunication between two FIFOs (refer to Figure 19) /g39/g50/g53/g37/g3/g50/g56/g55/g51/g56/g55 /g39/g44/g53/g37/g3/g50/g56/g55/g51/g56/g55 /g39/g50/g53/g36/g3/g50/g56/g55/g51/g56/g55 /g39/g44/g53/g36/g3/g50/g56/g55/g51/g56/g55 /g52/g81/g37/g3/g50/g56/g55/g51/g56/g55 /g52/g81/g36/g3/g50/g56/g55/g51/g56/g55 /g54/g44/g36/g3/g44/g49/g51/g56/g55 /g39/g81/g36/g3/g44/g49/g51/g56/g55 /g48/g53/g3/g3/g44/g49/g51/g56/g55 /g54/g50/g37/g3/g44/g49/g51/g56/g55 /g86/g72/g84/g88/g72/g81/g70/g72/g3/g20 /g86/g72/g84/g88/g72/g81/g70/g72/g3/g21/g86/g72/g84/g88/g72/g81/g70/g72/g3/g22 /g86/g72/g84/g88/g72/g81/g70/g72/g3/g23 /g86/g72/g84/g88/g72/g81/g70/g72/g3/g24 /g86/g72/g84/g88/g72/g81/g70/g72/g3/g25 /g11/g20/g12 /g11/g21/g12 /g11/g22/g12 /g11/g23/g12 /g11/g24/g12 /g11/g25/g12 /g11/g26/g12 /g11/g27/g12 /g11/g28/g12 /g11/g20/g19/g12 /g11/g20/g20/g12 /g11/g20/g21/g12 /g11/g20/g22/g12 /g11/g20/g23/g12 /g80/g74/g68/g25/g27/g26

Product data sheet Rev. 1 — 21 September 2012 27 of 32 NXP Semiconductors 74HC7403-Q100; 74HCT7403-Q100 4-bit x 64-word FIFO register; 3-state

13.1.3 Sequence 3 (FIFOA runs full)

When 65 words are shifted in, DORA remains HIGH due to valid data remaining at the output of FIFOA. QnA remains HIGH, being the polarity of the 65th word (6). After the 128th SI pulse, DIR remains LOW and both FIFOs are full (7). Additional pulses have no effect.

13.1.4 Sequence 4 (both FIFOs full, starting SHIFT-OUT)

SIA is held HIGH and two SOB pulses are applied (8). These pulses shift out two words and thus allow two empty locations to bubble-up to the input stage of FIFOB, and proceed to FIFOA (9). When the first empty location arrives at the input of FIFOA, a DIRA pulse is generated (10) and a new word is shifted into FIFOA. SIA is made LOW and now the second empty location reaches the input stage of FIFOA, after which DIRA remains HIGH (11).

13.1.5 Sequence 5 (FIFOA runs empty)

At the start of sequence 5, FIFOA contains 63 valid words due to two words being shifted out and one word being shifted in, in sequence 4. And additional series of SOB pulses are applied. After 63 SOB pulses, all words from FIFOA are shifted in FIFOB. DORA remains LOW (12).

13.1.6 Sequence 6 (FIFOB runs empty)

After the next SOB pulse, DIRB remains HIGH due to the input stage of FIFOB being empty. After another 63 SOB pulses, DORB remains LOW due to both FIFOS being empty (14). Additional SOB pulses have no effect. The last word remains available at the output Qn.

Product data sheet Rev. 1 — 21 September 2012 28 of 32 NXP Semiconductors 74HC7403-Q100; 74HCT7403-Q100 4-bit x 64-word FIFO register; 3-state 14. Package outline Fig 25. Package outline SOT109-1 (SO16) X w M θ AA1 bp D HE Lp Q detail X E Z e c L v M A (A )3 A y pin 1 index UNIT A max. A1 A2 A3 bp cD (1) E(1) (1)eH E LL p QZ y w v θ REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm inches 1.75 0.25 0.10 1.45 1.25 0.25 0.49 0.36 0.25 0.19 10.0 9.8 4.0 3.8 1.27 6.2 5.8 0.7 0.6 0.7 0.3 8 o o 0.25 0.1 DIMENSIONS (inch dimensions are derived from the original mm dimensions) Note 1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included. 1.0 0.4 SOT109-1 99-12-27 03-02-19 076E07 MS-012 0.069 0.010 0.004 0.057 0.049 0.01 0.019 0.014 0.0100 0.0075 0.39 0.38 0.16 0.15 0.05 1.05 0.0410.244 0.228 0.028 0.020 0.028 0.0120.01 0.25 0.01 0.0040.039 0.016 0 2.5 5 mm scale SO16: plastic small outline package; 16 leads; body width 3.9 mm SOT109-1

Table 9. Abbreviations Table 10. Revision history

Product data sheet Rev. 1 — 21 September 2012 30 of 32 NXP Semiconductors 74HC7403-Q100; 74HCT7403-Q100 4-bit x 64-word FIFO register; 3-state 17. Legal information

17.1 Data sheet status

[1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com.

17.2 Definitions

Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification — The information and data provided in a Product data sheet shall define the specification of the product as agreed between NXP Semiconductors and its customer, unless NXP Semiconductors and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the NXP Semiconductors product is deemed to offer functions and qualities beyond those described in the Product data sheet.

17.3 Disclaimers

Limited warranty and liability — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. NXP Semiconductors takes no responsibility for the content in this document if provided by an information source outside of NXP Semiconductors. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use in automotive applications — This NXP Semiconductors product has been qualified for use in automotive applications. Unless otherwise agreed in writing, the product is not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors and its suppliers accept no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer's own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product design. It is customer’s sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s applications or products, or the application or use by customer’s third party customer(s). Customer is responsible for doing all necessary testing for the customer’s applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customer’s third party customer(s). NXP does not accept any liability in this respect. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale — NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms , unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer’s general terms and conditions with regard to the purchase of NXP Semiconductors products by customer. Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification.

Product data sheet Rev. 1 — 21 September 2012 31 of 32 NXP Semiconductors 74HC7403-Q100; 74HCT7403-Q100 4-bit x 64-word FIFO register; 3-state No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities. Translations — A non-English (translated) version of a document is for reference only. The English version shall prevail in case of any discrepancy between the translated and English versions.

17.4 Trademarks

Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 18. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com

NXP Semiconductors 74HC7403-Q100; 74HCT7403-Q100 4-bit x 64-word FIFO register; 3-state © NXP B.V. 2012. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 21 September 2012 Document identifier: 74HC_HCT7403_Q100 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. 19. Contents

13.1.1 Sequence 1 (both FIFOs empty, starting

13.1.4 Sequence 4 (both FIFOs full, starting