DATASHEET SEARCH SITE

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 38

Technical content

Product specification File under Integrated Circuits, IC06 December 1990 INTEGRATED CIRCUITS 74HC/HCT7046A Phase-locked-loop with lock detector For a complete data sheet, please also download:

  • The IC06 74HC/HCT/HCU/HCMOS Logic Family Specifications
  • The IC06 74HC/HCT/HCU/HCMOS Logic Package Information
  • The IC06 74HC/HCT/HCU/HCMOS Logic Package Outlines

Philips Semiconductors Product specification Phase-locked-loop with lock detector 74HC/HCT7046A

FEATURES

  • Low power consumption
  • Centre frequency up to 17 MHz (typ.) at VCC = 4.5 V
  • Choice of two phase comparators: EXCLUSIVE-OR; edge-triggered JK flip-flop;
  • Excellent VCO frequency linearity
  • VCO-inhibit control for ON/OFF keying and for low standby power consumption
  • Minimal frequency drift
  • Operation power supply voltage range: VCO section 3.0 to 6.0 V digital section 2.0 to 6.0 V
  • Zero voltage offset due to op-amp buffering
  • Output capability: standard
  • I CC category: MSI GENERAL DESCRIPTION The 74HC/HCT7046 are high-speed Si-gate CMOS devices and are specified in compliance with JEDEC standard no. 7. The 74HC/HCT7046 are phase-locked-loop circuits that comprise a linear voltage-controlled oscillator (VCO) and two different phase comparators (PC1 and PC2) with a common signal input amplifier and a common comparator input. A lock detector is provided and this gives a HIGH level at pin 1 (LD) when the PLL is locked. The lock detector capacitor must be connected between pin 15 (C LD ) and pin 8 (GND). The value of the CLD capacitor can be determined, using information supplied in Fig.32. The input signal can be directly coupled to large voltage signals, or indirectly coupled (with a series capacitor) to small voltage signals. A self-bias input circuit keeps small voltage signals within the linear region of the input amplifiers. With a passive low-pass filter, the “7046” forms a second-order loop PLL. The excellent VCO linearity is achieved by the use of linear op-amp techniques. VCO The VCO requires one external capacitor C1 (between C1 A and C1B) and one external resistor R1 (between R 1 and GND) or two external resistors R1 and R2 (between R 1 and GND, and R2 and GND). Resistor R1 and capacitor C1 determine the frequency range of the VCO. Resistor R2 enables the VCO to have a frequency offset if required. The high input impedance of the VCO simplifies the design of low-pass filters by giving the designer a wide choice of resistor/capacitor ranges. In order not to load the low-pass filter, a demodulator output of the VCO input voltage is provided at pin 10 (DEM OUT ). In contrast to conventional techniques where the DEMOUT voltage is one threshold voltage lower than the VCO input voltage, here the DEM OUT voltage equals that of the VCO input. If DEMOUT is used, a load resistor (RS) should be connected from DEMOUT to GND; if unused, DEM OUT should be left open. The VCO output (VCOOUT ) can be connected directly to the comparator input (COMP IN), or connected via a frequency-divider. The VCO output signal has a duty factor of 50% (maximum expected deviation 1%), if the VCO input is held at a constant DC level. A LOW level at the inhibit input (INH) enables the VCO and demodulator, while a HIGH level turns both off to minimize standby power consumption. The only difference between the HC and HCT versions is the input level specification of the INH input. This input disables the VCO section. The comparators’ sections are identical, so that there is no difference in the SIG IN (pin 14) or COMPIN (pin 3) inputs between the HC and HCT versions. Phase comparators The signal input (SIG IN) can be directly coupled to the self-biasing amplifier at pin 14, provided that the signal swing is between the standard HC family input logic levels. Capacitive coupling is required for signals with smaller swings. Phase comparator 1 (PC1) This is an EXCLUSIVE-OR network. The signal and comparator input frequencies (f i) must have a 50% duty factor to obtain the maximum locking range. The transfer characteristic of PC1, assuming ripple (f r =2 fi) is suppressed, is: where VDEMOUT is the demodulator output at pin 10; VDEMOUT =V PC1OUT (via low-pass filter). The phase comparator gain is: The average output voltage from PC1, fed to the VCO input via the low-pass filter and seen at the demodulator output at pin 10 DEMOUT ), is the resultant of the phase differences of signals (SIGIN) and the comparator input (COMPIN) as shown in Fig.6. The average of V DEMOUT is equal to 1/2 VCC when there is no signal or noise at SIGIN and with this input the VCO oscillates at the centre frequency (f o). Typical V DEMOUT V CC K p V CC

Philips Semiconductors Product specification Phase-locked-loop with lock detector 74HC/HCT7046A waveforms for the PC1 loop locked at fo are shown in Fig.7. The frequency capture range (2fc) is defined as the frequency range of input signals on which the PLL will lock if it was initially out-of-lock. The frequency lock range (2f L) is defined as the frequency range of input signals on which the loop will stay locked if it was initially in lock. The capture range is smaller or equal to the lock range. With PC1, the capture range depends on the low-pass filter characteristics and can be made as large as the lock range. This configuration retains lock even with very noisy input signals. Typical behaviour of this type of phase comparator is that it can lock to input frequencies close to the harmonics of the VCO centre frequency. Phase comparator 2 (PC2) This is a positive edge-triggered phase and frequency detector. When the PLL is using this comparator, the loop is controlled by positive signal transitions and the duty factors of SIG IN and COMPIN are not important. PC2 comprises two D-type flip-flops, control-gating and a 3-state output stage. The circuit functions as an up-down counter (Fig.5) where SIG IN causes an up-count and COMPIN a down-count. The transfer function of PC2, assuming ripple (fr =fi) is suppressed, is: where VDEMOUT is the demodulator output at pin 10; V DEMOUT =V PC2OUT (via low-pass filter). V DEMOUT V CC The phase comparator gain is: VDEMOUT is the resultant of the initial phase differences of SIGIN and COMP IN as shown in Fig.8. Typical waveforms for the PC2 loop locked at fo are shown in Fig.9. When the frequencies of SIGIN and COMP IN are equal but the phase of SIGIN leads that of COMPIN, the p-type output driver at PC2OUT is held “ON” for a time corresponding to the phase difference (φDEMOUT ). When the phase of SIGIN lags that of COMP IN, the n-type driver is held “ON”. When the frequency of SIGIN is higher than that of COMPIN, the p-type output driver is held “ON” for most of the input signal cycle time, and for the remainder of the cycle both n and p- type drivers are “OFF” (3-state). If the SIG IN frequency is lower than the COMP IN frequency, then it is the n-type driver that is held “ON” for most of the cycle. Subsequently, the voltage at the capacitor (C2) of the low-pass filter connected to PC2 OUT varies until the signal and comparator inputs are equal in both phase and frequency. At this stable point the voltage on C2 remains constant as the PC2 output is in 3-state and the VCO input at pin 9 is a high impedance. Thus, for PC2, no phase difference exists between SIG IN and COMP IN over the full frequency range of the VCO. Moreover, the power dissipation due to the low-pass filter is reduced because both p and n-type drivers are “OFF” for most of the signal input cycle. It should be noted that the PLL lock range for this type of phase comparator is equal to the capture range and is independent of K p V CC the low-pass filter. With no signal present at SIGIN the VCO adjusts, via PC2, to its lowest frequency.

APPLICATIONS

  • FM modulation and demodulation
  • Frequency synthesis and multiplication
  • Frequency discrimination
  • Tone decoding
  • Data synchronization and conditioning
  • Voltage-to-frequency conversion
  • Motor-speed control

Philips Semiconductors Product specification Phase-locked-loop with lock detector 74HC/HCT7046A QUICK REFERENCE DATA GND = 0 V; Tamb =2 5°C; Notes 1. Applies to the phase comparator section only (VCO disabled). For power dissipation of VCO and demodulator sections see Figs 20, 21 and 22. 2. C PD is used to determine the dynamic power dissipation (PD inµW): PD =C PD × VCC 2 × fi+∑ (CL × VCC 2 × fo) where: fi= input frequency in MHz fo = output frequency in MHz ∑ (CL × VCC 2 × fo) = sum of outputs C L = output load capacitance in pF VCC = supply voltage in V

ORDERING INFORMATION

See “74HC/HCT/HCU/HCMOS Logic Package Information”. SYMBOL PARAMETER CONDITIONS TYPICAL UNIT HC HCT fo VCO centre frequency C1 = 40 pF; R1 = 3 k Ω ; VCC = 5 V 19 19 MHz C I input capacitance (pin 5) 3.5 3.5 pF C PD power dissipation capacitance per package notes 1 and 2 24 24 pF

Philips Semiconductors Product specification Phase-locked-loop with lock detector 74HC/HCT7046A PIN DESCRIPTION PIN NO. SYMBOL NAME AND FUNCTION

1 LD lock detector output (active HIGH)

2 PC1 OUT phase comparator 1 output

3 COMP IN comparator input

4 VCO OUT VCO output

5 INH inhibit input

A capacitor C1 connection A 7C 1 B capacitor C1 connection B

8 GND ground (0 V)

9 VCO

10 DEM OUT demodulator output

11 R 1 resistor R1 connection

12 R 2 resistor R2 connection

13 PC2 OUT phase comparator 2 output

14 SIG IN signal input

15 C LD lock detector capacitor input

16 V CC positive supply voltage

Fig.1 Pin configuration. Fig.2 Logic symbol. Fig.3 IEC logic symbol.

Philips Semiconductors Product specification Phase-locked-loop with lock detector 74HC/HCT7046A Fig.4 Functional diagram. MGA847 PHASE COMPARATOR LOCK DETECTOR PC2 OUT LD identical to 4046A C LD C CLD 7046A PHASE COMPARATOR PC2 OUT 13 PHASE COMPARATOR PC3 OUT 15 PHASE COMPARATOR PC1 OUT 2 PCP OUT 1 SIG INCOMP INVCO OUTC1A C1B DEM OUTINH VCO IN R 2 R 1 31 4476 51 0 9 (a) (b) 4046A VCO R S

Philips Semiconductors Product specification Phase-locked-loop with lock detector 74HC/HCT7046A Fig.5 Logic diagram. Fig.6 Phase comparator 1: average output voltage versus input phase difference: V DEMOUT V PC1OUT V CC φDEMOUT φSIGIN φCOMPIN–= Fig.7 Typical waveforms for PLL using phase comparator 1, loop locked at fo.

Philips Semiconductors Product specification Phase-locked-loop with lock detector 74HC/HCT7046A Fig.8 Phase comparator 2: average output voltage versus input phase difference: V DEMOUT V PC2OUT = V CC φDEMOUT φSIGIN φCOMPIN–() ˙ .= Fig.9 Typical waveforms for PLL using phase comparator 2, loop locked at fo.

Philips Semiconductors Product specification Phase-locked-loop with lock detector 74HC/HCT7046A RECOMMENDED OPERATING CONDITIONS FOR 74HC/HCT RATINGS Limiting values in accordance with the Absolute Maximum System (IEC 134) Voltages are referenced to GND (ground = 0 V) SYMBOL PARAMETER 74HC 74HCT UNIT CONDITIONS VCC DC supply voltage if VCO section is VI DC input voltage range 0 V CC 0V CC V VO DC output voltage range 0 V CC 0V CC V Tamb operating ambient temperature range−40 +85 −40 +85 °C see DC and AC CHARACTER- ISTICS Tamb operating ambient temperature range−40 +125 −40 +125 °C tr, tf input rise and fall times (pin 5) 6.0 1000 500 400 6.0 500 ns V CC = 2.0 V VCC = 4.5 V VCC = 6.0 V SYMBOL PARAMETER MIN. MAX. UNIT CONDITIONS VCC DC supply voltage −0.5 +7V ±IIK DC input diode current 20 mA for V I<− 0.5 V or VI > VCC + 0.5 V ±IOK DC output diode current 20 mA for V O <− 0.5 V or VO > VCC + 0.5 V ±IO DC output source or sink current 25 mA for − 0.5 V< VO < VCC + 0.5 V ±ICC ; ±IGND DC V CC or GND current 50 mA Tstg storage temperature range −65 +150 °C Ptot power dissipation per package plastic DIL 750 mW for temperature range:−40 to+125 °C 74HC/HCT above +70 °C: derate linearly with 12 mW/K plastic mini-pack (SO) 500 mW above +70 °C: derate linearly with 8 mW/K

Philips Semiconductors Product specification Phase-locked-loop with lock detector 74HC/HCT7046A DC CHARACTERISTICS FOR 74HC Quiescent supply current Voltages are referenced to GND (ground = 0 V) SYMBOL PARAMETER Tamb (°C) UNIT TEST CONDITIONS 74HC VCC (V) OTHER+25 −40 to+85 −40 to+125 ICC quiescent supply current (VCO disabled) 8.0 80.0 160.0 µA 6.0 pins 3, 5, and 14 at VCC ; pin 9 at GND; II at pins 3 and 14 to be excluded

Philips Semiconductors Product specification Phase-locked-loop with lock detector 74HC/HCT7046A Phase comparator section Voltages are referenced to GND (ground = 0 V) SYMBOL PARAMETER Tamb (°C) UNIT TEST CONDITIONS 74HC VCC (V) VI OTHER+25 −40 to+85 −40 to+125 VIH DC coupled HIGH level input voltage SIGIN, COMP IN 1.5 3.15 4.2 1.2 2.4 3.2 1.5 3.15 4.2 1.5 3.15 4.2 V 2.0 4.5 6.0 V IL DC coupled LOW level input voltage SIGIN, COMP IN 0.8 2.1 2.8 0.5 1.35 1.8 0.5 1.35 1.8 0.5 1.35 1.8 V 2.0 4.5 6.0 V OH HIGH level output voltage LD, PCnOUT 1.9 4.4 5.9 2.0 4.5 6.0 1.9 4.4 5.9 1.9 4.4 5.9 V 2.0 4.5 6.0 V IH or VIL −IO =2 0µA −IO =2 0µA −IO =2 0µA VOH HIGH level output voltage LD, PCnOUT 3.98 5.48 4.32 5.81 3.84 5.34 3.7 5.2 V 4.5 6.0 V IH or VIL −IO = 4.0 mA −IO = 5.2 mA VOL LOW level output voltage LD, PCnOUT 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 V 2.0 4.5 6.0 V IH or VIL IO =2 0µA IO =2 0µA IO =2 0µA VOL LOW level output voltage LD, PCnOUT 0.15 0.16 0.26 0.26 0.33 0.33 0.4 0.4 V 4.5 6.0 V IH or VIL IO = 4.0 mA IO = 5.2 mA ±II input leakage current SIGIN, COMP IN 3.0 7.0 18.0 30.0 4.0 9.0 23.0 38.0 5.0 11.0 27.0 45.0 µA 2.0 3.0 4.5 6.0 VCC or GND ±IOZ 3-state OFF-state current PC2 OUT 0.5 5.0 10.0 µA 6.0 V IH or VIL VO =V CC or GND R I input resistance SIGIN, COMP IN 800 250 150 kΩ 3.0 4.5 6.0 VI at self-bias operating point; ΔV I= 0.5 V; see Figs 10, 11 and 12

Philips Semiconductors Product specification Phase-locked-loop with lock detector 74HC/HCT7046A VCO section Voltages are referenced to GND (ground = 0 V) Note 1. The parallel value of R1 and R2 should be more than 2.7 kΩ . Optimum performance is achieved when R1 and/or R2 are/is> 10 kΩ . SYM- BOL PARAMETER Tamb (°C) UNIT TEST CONDITIONS 74HC VCC (V) VI OTHER+25 −40 to+85 −40 to+125 VIH HIGH level input voltage INH 2.1 3.15 4.2 1.7 2.4 3.2 2.1 3.15 4.2 2.1 3.15 4.2 V 3.0 4.5 6.0 V IL LOW level input voltage INH 1.3 2.1 2.8 0.9 1.35 1.8 0.9 1.35 1.8 0.9 1.35 1.8 V 3.0 4.5 6.0 V OH HIGH level output voltage VCO OUT 2.9 4.4 5.9 3.0 4.5 6.0 2.9 4.4 5.9 2.9 4.4 5.9 V 3.0 4.5 6.0 V IH or VIL −IO =2 0µA −IO =2 0µA −IO =2 0µA VOH HIGH level output voltage VCO OUT 3.98 5.48 4.32 5.81 3.84 5.34 3.7 5.2 V 4.5 6.0 V IH or VIL −IO = 4.0 mA −IO = 5.2 mA VOL LOW level output voltage VCO OUT 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 V 3.0 4.5 6.0 V IH or VIL IO =2 0µA IO =2 0µA IO =2 0µA VOL LOW level output voltage VCO OUT 0.15 0.16 0.26 0.26 0.33 0.33 0.4 0.4 V 4.5 6.0 V IH or VIL IO = 4.0 mA IO = 5.2 mA VOL LOW level output voltage C1A,C1 B (test purposes only) 0.40 0.40 0.47 0.47 0.54 0.54 V 4.5 6.0 VIH or VIL IO = 4.0 mA IO = 5.2 mA ±II input leakage current INH, VCOIN 0.1 1.0 1.0 µA 6.0 VCC or GND R1 resistor range 3.0 3.0 3.0 300 300 300 kΩ 3.0 4.5 6.0 note 1 R2 resistor range 3.0 3.0 3.0 300 300 300 kΩ 3.0 4.5 6.0 note 1 C1 capacitor range no limit pF 3.0 4.5 6.0 V VCOIN operating voltage range at VCOIN 1.1 1.1 1.1 1.9 3.4 4.9 V 3.0 4.5 6.0 over the range specified for R1; for linearity see Figs 18 and 19.

Philips Semiconductors Product specification Phase-locked-loop with lock detector 74HC/HCT7046A Demodulator section Voltages are referenced to GND (ground = 0 V) SYMBOL PARAMETER Tamb (°C) UNIT TEST CONDITIONS 74HC VCC (V) OTHER+25 −40 to+85 −40 to+125 R S resistor range 50 300 300 300 kΩ 3.0 4.5 6.0 at R S > 300 kΩ the leakage current can influence V DEMOUT VOFF offset voltage VCO IN to VDEMOUT ±30 ±20 ±10 mV 3.0 4.5 6.0 V I=V VCOIN = 1/2 VCC ; values taken over R S range; see Fig.13 R D dynamic output resistance at DEMOUT Ω 3.0 4.5 6.0 V DEMOUT = 1/2 VCC

Philips Semiconductors Product specification Phase-locked-loop with lock detector 74HC/HCT7046A AC CHARACTERISTICS FOR 74HC Phase comparator section GND = 0 V; tr =tf= 6 ns; CL = 50 pF VCO section GND = 0 V; tr =tf= 6 ns; CL = 50 pF SYMBOL PARAMETER Tamb (°C) UNIT TEST CONDITIONS 74HC VCC (V) OTHER+25 −40 to+85 −40 to+125 tPHL / tPLH propagation delay SIGIN, COMP IN to PC1OUT 200 250 300 ns 2.0 4.5 6.0 Fig.14 t PZH / tPZL 3-state output enable time SIGIN, COMP IN to PC2OUT 280 350 420 ns 2.0 4.5 6.0 Fig.15 t PHZ / tPLZ 3-state output disable time SIGIN, COMP IN to PC2OUT 325 405 490 ns 2.0 4.5 6.0 Fig.15 t THL / tTLH output transition time 19 110 ns 2.0 4.5 6.0 Fig.14 V I(p-p) AC coupled input sensitivity (peak-to-peak value) at SIG IN or COMPIN mV 2.0 3.0 4.5 6.0 f i= 1 MHz SYM- BOL PARAMETER Tamb (°C) UNIT TEST CONDITIONS 74HC VCC (V) OTHER+25 −40 to+85 −40 to+125 Δf/T frequency stability with temperature change 0.20 0.15 0.14 %/K 3.0 4.5 6.0 V I=V VCOIN =1/2 VCC ; R1 = 100 kΩ ; R2 =∞ ; C1 = 100 pF; see Fig.16 fo VCO centre frequency (duty factor = 50%) 7.0 11.0 13.0 10.0 17.0 21.0 MHz 3.0 4.5 6.0 V VCOIN = 1/2 VCC ; C1 = 40 pF; see Fig.17 ΔfVCO VCO frequency linearity 1.0 0.4 0.3 % 3.0 4.5 6.0 R1 = 100 kΩ ; R2 =∞ ; C1 = 100 pF; see Figs 18 and 19 δ VCO duty factor at VCO OUT % 3.0 4.5 6.0

Philips Semiconductors Product specification Phase-locked-loop with lock detector 74HC/HCT7046A DC CHARACTERISTICS FOR 74HCT Quiescent supply current Voltages are referenced to GND (ground = 0 V) Note 1. The value of additional quiescent supply current (ΔICC ) for a unit load of 1 is given above. To determineΔICC per input, multiply this value by the unit load coefficient shown in the table below. SYMBOL PARAMETER Tamb (°C) UNIT TEST CONDITIONS 74HCT VCC (V) OTHER+25 −40 to+85 −40 to+125 ICC quiescent supply current (VCO disabled) 8.0 80.0 160.0 µA 6.0 pins 3, 5 and 14 at VCC ; pin 9 at GND; II at pins 3 and 14 to be excluded ΔI CC additional quiescent supply current per input pin for unit load coefficient is 1 (note 1) V I=V CC − 2.1 V 100 360 450 490 µA 4.5 to 5.5 pins 3 and 14 at V CC ; pin 9 at GND; II at pins 3 and 14 to be excluded INPUT UNIT LOAD COEFFICIENT INH 1.00

Philips Semiconductors Product specification Phase-locked-loop with lock detector 74HC/HCT7046A Phase comparator section Voltages are referenced to GND (ground = 0 V) SYM BOL PARAMETER Tamb (°C) UNIT TEST CONDITIONS 74HCT VCC (V) VI OTHER+25 −40 to+85 −40 to+125 VIH DC coupled HIGH level input voltage SIG IN, COMP IN 3.15 2.4 V 4.5 VIL DC coupled LOW level input voltage SIG IN, COMP IN 2.1 1.35 V 4.5 VOH HIGH level output voltage LD, PCnOUT VIH or VIL −IO =2 0µA VOH HIGH level output voltage LD, PCnOUT VIH or VIL −IO = 4.0 mA VOL LOW level output voltage LD, PCnOUT 0 0.1 0.1 0.1 V 4.5 VIH or VIL IO =2 0µA VOL LOW level output voltage LD, PCnOUT VIH or VIL IO = 4.0 mA ±II input leakage current SIGIN, COMP IN 30 38 45 µA 5.5 VCC or GND ±IOZ 3-state OFF-state current PC2 OUT 0.5 5.0 10.0 µA 5.5 VIH or VIL VO =V CC or GND R I input resistance SIGIN, COMP IN 250 k Ω 4.5 VI at self-bias operating point; ΔV I= 0.5 V; see Figs 10, 11 and 12

Philips Semiconductors Product specification Phase-locked-loop with lock detector 74HC/HCT7046A DC CHARACTERISTICS FOR 74HCT VCO section Voltages are referenced to GND (ground = 0 V) Note 1. The parallel value of R1 and R2 should be more than 2.7 kΩ . Optimum performance is achieved when R1 and/or R2 are/is> 10 kΩ . SYMBOL PARAMETER Tamb (°C) UNIT TEST CONDITIONS 74HCT VCC (V) VI OTHER+25 −40 to+85 −40 to+125 VIH HIGH level input voltage INH to 5.5 V IL LOW level input voltage INH to 5.5 V OH HIGH level output voltage VCO OUT or V IL −IO =2 0µA VOH HIGH level output voltage VCO OUT or V IL −IO = 4.0 mA VOL LOW level output voltage VCO OUT 0 0.1 0.1 0.1 V 4.5 V IH or V IL IO =2 0µA VOL LOW level output voltage VCO OUT or V IL IO = 4.0 mA VOL LOW level output voltage C1A, C1B (test purposes only) 0.40 0.47 0.54 V 4.5 V IH or VIL IO = 4.0 mA ±II input leakage current INH, VCOIN 0.1 1.0 1.0 µA 5.5 VCC or GND R1 resistor range 3.0 300 k Ω 4.5 note 1 R2 resistor range 3.0 300 k Ω 4.5 note 1 C1 capacitor range 40 no limit pF 4.5 VVCOIN operating voltage range at VCOIN 1.1 3.4 V 4.5 over the range specified for R1; for linearity see Figs 18 and 19.

Philips Semiconductors Product specification Phase-locked-loop with lock detector 74HC/HCT7046A Demodulator section Voltages are referenced to GND (ground = 0 V) AC CHARACTERISTICS FOR 74HCT Phase comparator section GND = 0 V; tr =tf= 6 ns; CL = 50 pF SYMBOL PARAMETER Tamb (°C) UNIT TEST CONDITIONS 74HCT VCC (V) OTHER+25 −40 to+85 −40 to+125 R S resistor range 50 300 k Ω 4.5 at RS > 300 kΩ the leakage current can influence V DEMOUT VOFF offset voltage VCO IN to VDEMOUT ±20 mV 4.5 V I=V VCOIN = 1/2 VCC ; values taken over RS range; see Fig.13 R D dynamic output resistance at DEMOUT 25 Ω 4.5 V DEMOUT = 1/2 VCC SYMBOL PARAMETER Tamb (°C) UNIT TEST CONDITIONS 74HCT VCC (V) OTHER+25 −40 to+85 −40 to+125 tPHL / tPLH propagation delay SIGIN, COMP IN to PC1OUT 21 40 50 60 ns 4.5 Fig.14 tPZH / tPZL 3-state output enable time SIGIN, COMP IN to PC2OUT 27 56 70 84 ns 4.5 Fig.15 tPHZ / tPLZ 3-state output disable time SIGIN, COMP IN to PC2OUT 35 65 81 98 ns 4.5 Fig.15 tTHL / tTLH output transition time 7 15 19 22 ns 4.5 Fig.14 VI(p-p) AC coupled input sensitivity (peak-to-peak value) at SIG IN or COMPIN 15 mV 4.5 f i=

1 MHz

Philips Semiconductors Product specification Phase-locked-loop with lock detector 74HC/HCT7046A VCO section GND = 0 V; tr =tf= 6 ns; CL = 50 pF SYMBOL PARAMETER Tamb (°C) UNIT TEST CONDITIONS 74HCT VCC (V) OTHER+25 −40 to+85 −40 to+125 Δf/T frequency stability with temperature change 0.15 %/K 4.5 V I=V COIN within recommended range; R1 = 100 kΩ ; R2 = ∞ ; C1 = 100 pf; see Fig.16b f o VCO centre frequency (duty factor = 50%) 11.0 17.0 MHz 4.5 V VCOIN = 1/2 VCC ; C1 = 40 pF; see Fig.17 Δf VCO VCO frequency linearity 0.4 % 4.5 R1 = 100 k Ω ; R2 = ∞ ; C1 = 100 pF; see Figs 18 and 19 δ VCO duty factor at VCOOUT 50 % 4.5

Philips Semiconductors Product specification Phase-locked-loop with lock detector 74HC/HCT7046A FIGURE REFERENCES FOR DC CHARACTERISTICS Fig.10 Typical input resistance curve at SIGIN, COMP IN. Fig.11 Input resistance at SIGIN, COMP IN with ΔVI= 0.5 V at self-bias point. Fig.12 Input current at SIGIN, COMP IN with ΔVI= 0.5 V at self-bias point. Fig.13 Offset voltage at demodulator output as a function of VCOIN and RS. ____ RS = 50 kΩ

Philips Semiconductors Product specification Phase-locked-loop with lock detector 74HC/HCT7046A AC WAVEFORMS Fig.14 Waveforms showing input (SIGIN, COMP IN) to output (PC1OUT ) propagation delays and the output transition times. (1) HC : VM = 50%; VI= GND to VCC . Fig.15 Waveforms showing the 3-state enable and disable times for PC2OUT . (1) HC : VM = 50%; VI= GND to VCC .

Philips Semiconductors Product specification Phase-locked-loop with lock detector 74HC/HCT7046A Fig.16 Frequency stability of the VCO as a function of ambient temperature with supply voltage as a parameter.  without offset (R2 =∞ ): (a) R1 = 3 kΩ ; (b) R1 = 10 kΩ ; (c) R1 = 300 kΩ . - - - - with offset (R1 =∞ ): (a) R2 = 3 kΩ ; (b) R2 = 10 kΩ ; (c) R2 = 300 kΩ . In (b), the frequency stability for R1 = R2 = 10 kΩ at 5 V is also given (curve A). This curve is set by the total VCO bias current, and is not simply the addition of the two 10 kΩ stability curves. C1 = 100 pF; VVCO IN = 0.5 VCC . handbook, halfpage MSB710 Tamb (oC) 150100500−50 −25 −20 −15 −10 Δf (%) 5 V 6 V 3 V 4.5 V 5 V 6 V V =CC 3 V (a) handbook, halfpage MSB711 T ( C)amb f (%) o 15010050050 Δ 5 V 6 V 3 V 5 V 6 V V =CC3 V (b) A handbook, halfpage MSB712 T ( C)amb f (%) o 15010050050 Δ 5 V 6 V (c) V =CC

3 V 3 V

Philips Semiconductors Product specification Phase-locked-loop with lock detector 74HC/HCT7046A AC WAVEFORMS Fig.16 Continued. To obtain optimum temperature stability, C1 must be a small as possible, but larger than 100 pF.

Philips Semiconductors Product specification Phase-locked-loop with lock detector 74HC/HCT7046A Fig.17 Graphs showing VCO frequency (fVCO ) as a function of the VCO input voltage (VVCOIN ).

Philips Semiconductors Product specification Phase-locked-loop with lock detector 74HC/HCT7046A Fig.18 Definition of VCO frequency linearity: ΔV = 0.5 V over the VCC range: for VCO linearity f′0 f1 f2+ linearity f′0 f0– f′0 Fig.19 Frequency linearity as a function of R1, C1 and VCC : R2 =∞ and ΔV = 0.5 V.

Philips Semiconductors Product specification Phase-locked-loop with lock detector 74HC/HCT7046A Fig.20 Power dissipation versus the value of R1: C L = 50 pF; R2 =∞ ; VVCOIN = 1/2 VCC ; Tamb =2 5°C. ____ C1 = 40 pF - - - - C1 = 1µF Fig.21 Power dissipation versus the value of R2: C L = 50 pF; R1 =∞ ; VVCOIN = GND = 0 V; Tamb =2 5°C. ____ C1 = 40 pF - - - - C1 = 1µF Fig.22 Typical dc power dissipation of demodulator section as a function of RS: R1 = R2 =∞ ; Tamb =2 5°C; VVCOIN = 1/2 VCC .

Philips Semiconductors Product specification Phase-locked-loop with lock detector 74HC/HCT7046A

APPLICATION INFORMATION

This information is a guide for the approximation of values of external components to be used with the 74HC/HCT7046 in a phase-lock-loop system. References should be made to Figs 27, 28 and 29 as indicated in the table. Values of the selected components should be within the following ranges: R1 between 3 k Ω and 300 kΩ; R2 between 3 k Ω and 300 kΩ; R1 + R2 parallel value> 2.7 kΩ ; C1 greater than 40 pF. SUBJECT PHASE COMPARATOR DESIGN CONSIDERATIONS VCO frequency characteristic VCO frequency without extra offset PC1, PC2 With R2 = ∞ and R1 within the range 3 kΩ< R1 < 300 kΩ , the characteristics of the VCO operation will be as shown in Fig. 23. (Due to R1, C1 time constant a small offset remains when R2 =∞ .) Fig. 23 Frequency characteristic of VCO operating without offset: f o = centre frequency; 2fL = frequency lock range. Selection of R1 and C1 PC1 Given f o, determine the values of R1 and C1 using Fig.27. PC2 Given f max and fo, determine the values of R1 and C1 using Fig.27, use Fig.29 to obtain 2fL and then use this to calculate fmin.

Philips Semiconductors Product specification Phase-locked-loop with lock detector 74HC/HCT7046A VCO frequency characteristic VCO frequency with extra offset PC1, PC2 With R1 and R2 within the ranges 3 k Ω< R1< 300 kΩ, 3 kΩ< R2 < 300 kΩ , the characteristics of the VCO operation will be as shown in Fig. 24. Fig. 24 Frequency characteristic of VCO operating with offset: f o = centre frequency; 2fL = frequency lock range. Selection of R1, R2 and C1 PC1, PC2 Given f 0 and fL, determine the value of product R1C1 by using Fig.29. Calculate foff from the equation foff=fo − 1.6fL. Obtain the values of C1 and R2 by using Fig.28. Calculate the value of R1 from the value of C1 and the product R1C1. SUBJECT PHASE COMPARATOR DESIGN CONSIDERATIONS

Philips Semiconductors Product specification Phase-locked-loop with lock detector 74HC/HCT7046A PLL conditions with no signal at the SIG IN input PC1 VCO adjusts to f o withφDEMOUT =9 0° and VVCOIN = 1/2 VCC (see Fig.6). PC2 VCO adjusts to f o withφDEMOUT = −360° and VVCOIN = min. (see Fig.8). PLL frequency capture range PC1, PC2 Loop filter component selection (a)τ = R3 x C2 (b) amplitude characteristic (c) pole-zero diagram Fig. 25 Simple loop filter for PLLwithout offset; R3≥ 500 Ω . (a)τ1 = R3 x C2; (b) amplitude characteristic (c) pole-zero diagram τ2 = R4 x C2; τ3 = (R3 + R4) x C2 Fig. 26 Simple loop filter for PLL with offset; R3+ R4 ≥ 500 Ω . PLL locks on harmonics at centre frequency PC1 yes PC2 no noise rejection at signal input PC1 high PC2 low AC ripple content when PLL is locked PC1 f r =2 fi, large ripple content atφDEMOUT =9 0° PC2 f r =fi, small ripple content atφDEMOUT =0 ° SUBJECT PHASE COMPARATOR DESIGN CONSIDERATIONS

Philips Semiconductors Product specification Phase-locked-loop with lock detector 74HC/HCT7046A Fig.27 Typical value of VCO centre frequency (fo) as a function of C1: R2 =∞ ; VVCOIN = 1/2 VCC ; INH = GND; Tamb =2 5°C. (1) To obtain optimum VCO performance, C1 must be as small as possible but larger than 100 pF. (2) Interpolation for various values of R1 can be easily calculated because a constant R1C1 product will produce almost the same VCO output frequency.

Philips Semiconductors Product specification Phase-locked-loop with lock detector 74HC/HCT7046A Fig.28 Typical value of frequency offset as a function of C1: R1 =∞ ; VVCOIN = 1/2 VCC ; INH = GND; Tamb =2 5°C. (1) To obtain optimum VCO performance, C1 must be as small as possible but larger than 100 pF. (2) Interpolation for various values of R2 can be easily calculated because a constant R2C2 product will produce almost the same VCO output frequency.

Philips Semiconductors Product specification Phase-locked-loop with lock detector 74HC/HCT7046A Fig.29 Typical frequency lock range (2fL) versus the product R1C1: VVCOIN range = 0.9 to (VCC − 0.9) V; R2 = ∞ ; VCO gain: K V 2fL

Philips Semiconductors Product specification Phase-locked-loop with lock detector 74HC/HCT7046A The built-in lock-detection circuit will only work when used in conjunction with the phase comparator PC2. The lock-indication is derived from the phase error between SIG IN and COMP IN. The PC2 has a typical phase error of zero degrees over the entire VCO operating range. However, to remain in-lock the circuit requires some small adjustments. The variation is dependent on the loop parameters and back-lash time (typically 5 ns). Depending on the application, the phase error can be defined as the limit, a phase error of greater magnitude would be considered out-of-lock. An example of an in-lock detection circuit using the “7046A” is shown in Fig.30. If the PLL is in-lock, only very small pulses will come from the “up” or “down” connections of PC2. These pulses are filtered out by a RC network. A Schmitt trigger produces a steady state level, a HIGH level indicates an in-lock condition and a pulsed output indicates an out-of-lock condition as shown in Fig.31. Fig.30 An example of an in-lock detection circuit using the “7046A”. See Fig.31 for input waveform. Fig.31 Waveforms showing the lock detection process; (a) in-lock; (b) out-of-lock. (a) (b)

Philips Semiconductors Product specification Phase-locked-loop with lock detector 74HC/HCT7046A Fig.32 CLD capacitor value versus typical tLD . C LD = capacitor connected to pin 15 (includes the parasitic input capacitance of the IC, approximately 3.5 pF). tLD = phase difference between SIGIN and COMP IN (positive-going edges).

Philips Semiconductors Product specification Phase-locked-loop with lock detector 74HC/HCT7046A The maximum permitted phase error must be defined, before tLD can be defined using the following formula: Using this calculated value in Fig.32, it is possible to define the value of C LD , e.g. assuming the phase error is 36° and fIN = 2 MHz: and using Fig.32, it can be seen that C LD is 26 pF. With the addition of one retriggerable monostable (e.g. “123”, “423” or “4538”) a steady state LOW and HIGH indication can be obtained, as shown in Fig.33. t LD φmax fIN tLD 36° Fig.33 Steady state signal for lock indication.

Philips Semiconductors Product specification Phase-locked-loop with lock detector 74HC/HCT7046A PLL design example The frequency synthesizer, used in the design example shown in Fig.34, has the following parameters: Output frequency: 2 MHz to 3 MHz frequency steps : 100 kHz settling time : 1 ms overshoot : < 20% The open-loop gain is H (s) x G (s) = K p × Kf× Ko × Kn. Where: The programmable counter ratio Kn can be found as follows: The VCO is set by the values of R1, R2 and C1, R2 = 10 kΩ (adjustable). The values can be determined using the information in the section “DESIGN CONSIDERATIONS”. With f o = 2.5 MHz and fL = 500 kHz this gives the following values (VCC = 5.0 V): R1 = 10 kΩ R2 = 10 kΩ C1 = 500 pF The VCO gain is: The gain of the phase comparator is: The transfer gain of the filter is given by: Where: Kp = phase comparator gain Kf = low-pass filter transfer gain Ko =K v/s VCO gain Kn = 1/n divider ratio N min. fout fstep N max. fout fstep K V 2fL 2 π×× K p V CC K f 1 τ2s+ τ1 R3C2 and τ2 R4C2.== The characteristics equation is: This results in: The natural frequencyω n is defined as follows: and the damping valueζ is defined as follows: The overshoot and settling time percentages are now used to determineω n. From Fig.35 it can be seen that the damping ratioζ = 0.8 will produce an overshoot of less than 20% and settle to within 5% atω nt = 4.5. The required settling time is 1 ms. This results in: Rewriting the equation for natural frequency results in: The maximum overshoot occurs at Nmax .: When C2 = 470 nF, then R3 is calculated using the damping ratio equation: s2 1K p K v K n×τ 2××+ K p K v× K n× ω n K p K v× K n× ζ 1 2ω n 1K p K v× K n×τ 2×+ ω n t--- 5 τ1 τ2+() K p K v× K n× ω n 5000 30×

Philips Semiconductors Product specification Phase-locked-loop with lock detector 74HC/HCT7046A Note For an extensive description and application example please refer to application note ordering number 9398 649 90011. Also available a computer design program for PLL’s ordering number 9398 961 10061. Since the output frequency is proportional to the VCO control voltage, the PLL frequency response can be observed with an oscilloscope by monitoring pin 9 of the VCO. The average frequency response, as calculated by the Laplace method, is found experimentally by smoothing this voltage at pin 9 with a simple RC filter, whose time constant is long compared to the phase detector sampling rate but short compared to the PLL response time. Fig.34 Frequency synthesizer. Fig.35 Type 1, second order frequency step response. 012 4 1.6 1.0 0.6 0.8 MGA959 1.4 1.2 0.4 0.2 5678 ω nt Δω (t)e Δω e /ω n ΔΦ (t)e ΔΦ e /ω n −0.6 0.4 1.0 0.2 −0.4 −0.2 0.6 0.8 = 5.0ζ 0.5 0.707 1.0 = 0.3 ζ = 2.0ζ

Philips Semiconductors Product specification Phase-locked-loop with lock detector 74HC/HCT7046A PACKAGE OUTLINES See “74HC/HCT/HCU/HCMOS Logic Package Outlines”. Fig.36 Frequency compared to the time response.