74HC670 PHILIPS

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 9

Technical content

Product specification File under Integrated Circuits, IC06 December 1990 INTEGRATED CIRCUITS 74HC/HCT670 4 x 4 register file; 3-state For a complete data sheet, please also download:

  • The IC06 74HC/HCT/HCU/HCMOS Logic Family Specifications
  • The IC06 74HC/HCT/HCU/HCMOS Logic Package Information
  • The IC06 74HC/HCT/HCU/HCMOS Logic Package Outlines

Philips Semiconductors Product specification 4 x 4 register file; 3-state 74HC/HCT670

FEATURES

  • Simultaneous and independent read and write operations
  • Expandable to almost any word size and bit length
  • Output capability: bus driver
  • ICC category: MSI GENERAL DESCRIPTION The 74HC/HCT670 are high-speed Si-gate CMOS devices and are pin compatible with low power Schottky TTL (LSTTL). They are specified in compliance with JEDEC standard no. 7A. The 74HC/HCT670 are 16-bit 3-state register files organized as 4 words of 4 bits each. Separated read and write address inputs (R A, RB and WA,W B) and enable inputs (RE andWE) are available, permitting simultaneous writing into one word location and reading from another location. The 4-bit word to be stored is presented to four data inputs (D 0 to D3). The WA and WB inputs determine the location of the stored word. When theWE input is LOW, the data is entered into the addressed location. The addressed location remains transparent to the data while the WE input is LOW. Data supplied at the inputs will be read out in true (non-inverting) form from the 3-state outputs (Q 0 to Q3). Dn and Wn inputs are inhibited when WE is HIGH. Direct acquisition of data stored in any of the four registers is made possible by individual read address inputs A and RB). The addressed word appears at the four outputs when theRE is LOW. Data outputs are in the high impedance OFF-state whenRE is HIGH. This permits outputs to be tied together to increase the word capacity to very large numbers. Design of the read enable signals for the stacked devices must ensure that there is no overlap in the LOW levels which would cause more than one output to be active at the same time. Parallel expansion to generate n-bit words is accomplished by driving the enable and address inputs of each device in parallel. QUICK REFERENCE DATA GND = 0 V; T amb =2 5°C; tr =tf= 6 ns Notes 1. C PD is used to determine the dynamic power dissipation (PD inµW): PD =C PD × VCC 2 × fi+∑ (CL × VCC 2 × fo) where: fi = input frequency in MHz fo = output frequency in MHz ∑ (CL × VCC 2 × fo) = sum of outputs C L = output load capacitance in pF VCC = supply voltage in V 2. For HC the condition is VI= GND to VCC ; for HCT the condition is VI= GND to VCC −1.5 V

ORDERING INFORMATION

See “74HC/HCT/HCU/HCMOS Logic Package Information”. SYMBOL PARAMETER CONDITIONS TYPICAL UNIT HC HCT tPHL / tPLH propagation delay Dn to Qn C L = 15 pF; VCC = 5 V 23 23 ns C I input capacitance 3.5 3.5 pF C PD power dissipation capacitance per package notes 1 and 2 122 124 pF

Philips Semiconductors Product specification 4 x 4 register file; 3-state 74HC/HCT670 PIN DESCRIPTION PIN NO. SYMBOL NAME AND FUNCTION 5, 4 R A, RB read address inputs

8 GND ground (0 V)

10, 9, 7, 6 Q 0 to Q3 data outputs

11 RE 3-state output read enable input (active LOW)

12 WE write enable input (active LOW)

14, 13 W A, WB write address inputs 15, 1, 2, 3 D0 to D3 data inputs

16 V CC positive supply voltage

Fig.1 Pin configuration. Fig.2 Logic symbol. Fig.3 IEC logic symbol. Fig.4 Functional diagram. WRITE MODE SELECT TABLE Note 1. The write address (WA and WB) to the “internal latches” must be stable whileWE is LOW for conventional operation. OPERATING MODE INPUTS INTERNAL LATCHES (1) WE D n write data L L L H L H data latched H X no change READ MODE SELECT TABLE Notes 1. The selection of the “internal latches” by read address (RA and RB) are not constrained byWE or RE operation. H = HIGH voltage level L = LOW voltage level X = don’t care Z = high impedance OFF-state OPERATING MODE INPUTS OUTPUT RE INTERNAL LATCHES (1) Q n read L L L H L H disabled H X Z

Philips Semiconductors Product specification 4 x 4 register file; 3-state 74HC/HCT670 Fig.5 Logic diagram.

Philips Semiconductors Product specification 4 x 4 register file; 3-state 74HC/HCT670 DC CHARACTERISTICS FOR 74HC For the DC characteristics see“74HC/HCT/HCU/HCMOS Logic Family Specifications”. Output capability: bus driver I CC category: MSI AC CHARACTERISTICS FOR 74HC GND = 0 V; tr =tf= 6 ns; CL =5 0p F SYMBOL PARAMETER Tamb (°C) UNIT TEST CONDITIONS 74HC VCC (V) WAVEFORMS+25 −40 to+85 −40 to+125 tPHL / tPLH propagation delay R A, RB to Qn 195 245 295 ns 2.0 4.5 6.0 Fig.6 t PHL / tPLH propagation delay WE to Qn 250 315 375 ns 2.0 4.5 6.0 Fig.7 t PHL / tPLH propagation delay D n to Qn 250 315 375 ns 2.0 4.5 6.0 Fig.7 t PZH / tPZL 3-state output enable time RE to Qn 150 190 225 ns 2.0 4.5 6.0 Fig.9 t PHZ / tPLZ 3-state output disable time RE to Qn 150 190 225 ns 2.0 4.5 6.0 Fig.9 t THL / tTLH output transition time 14 ns 2.0 4.5 6.0 Fig.6 t W write enable pulse width LOW 100 120 ns 2.0 4.5 6.0 Fig.8 t su set-up time D n toWE ns 2.0 4.5 6.0 Fig.8 t su set-up time W A, WB toWE ns 2.0 4.5 6.0 Fig.8 t h hold time D n toWE ns 2.0 4.5 6.0 Fig.8 t h hold time W A, WB toWE ns 2.0 4.5 6.0 Fig.8 t latch latch time WE to RA, RB 100 125 150 ns 2.0 4.5 6.0 Fig.8

Philips Semiconductors Product specification 4 x 4 register file; 3-state 74HC/HCT670 DC CHARACTERISTICS FOR 74HCT For the DC characteristics see“74HC/HCT/HCU/HCMOS Logic Family Specifications”. Output capability: bus driver ICC category: MSI Note to HCT types The value of additional quiescent supply current (ΔICC ) for a unit load of 1 is given in the family specifications. To determineΔICC per input, multiply this value by the unit load coefficient shown in the table below. INPUT UNIT LOAD COEFFICIENT D n WE, W A W B 0.25 0.40 0.60 R A R B RE 0.70 1.10 1.35

Philips Semiconductors Product specification 4 x 4 register file; 3-state 74HC/HCT670 AC CHARACTERISTICS FOR 74HCT GND = 0 V; tr =tf= 6 ns; CL =5 0p F SYMBOL PARAMETER Tamb (°C) UNIT TEST CONDITIONS 74HCT VCC (V) WAVEFORMS+25 −40 to+85 −40 to+125 tPHL / tPLH propagation delay R A, RB to Qn 21 40 50 60 ns 4.5 Fig.6 tPHL / tPLH propagation delay WE to Qn 28 50 63 75 ns 4.5 Fig.7 tPHL / tPLH propagation delay D n to Qn 27 50 63 75 ns 4.5 Fig.7 tPZH / tPZL 3-state output enable time RE to Qn 18 35 44 53 ns 4.5 Fig.9 tPHZ / tPLZ 3-state output disable time RE to Qn 19 35 44 53 ns 4.5 Fig.9 tTHL / tTLH output transition time 5 12 15 18 ns 4.5 Fig.6 tW write enable pulse width LOW 18 9 23 27 ns 4.5 Fig.8 tsu set-up time D n toWE 12 4 15 18 ns 4.5 Fig.8 tsu set-up time W A, WB toWE 12 −2 15 18 ns 4.5 Fig.8 th hold time D n toWE 5 −1 5 5 ns 4.5 Fig.8 th hold time W A, WB toWE 5 0 5 5 ns 4.5 Fig.8 tlatch latch time WE to RA, RB 25 11 31 38 ns 4.5 Fig.8

Philips Semiconductors Product specification 4 x 4 register file; 3-state 74HC/HCT670 AC WAVEFORMS Fig.6 Waveforms showing the read address input (RA, RB) to output (Qn) propagation delays and output transition times. (1) HC : VM = 50%; VI= GND to VCC . HCT : VM = 1.3 V; VI= GND to 3 V. Fig.7 Waveforms showing the write enable input (WE) and data input (Dn) to output (Qn) propagation delays, and the write enable pulse width. (1) HC : VM = 50%; VI= GND to VCC . HCT : VM = 1.3 V; VI= GND to 3 V. Fig.8 Waveforms showing the write address input (WA, WB) and data input (Dn) to write enable (WE) set-up, hold and latch times. (1) HC : VM = 50%; VI= GND to VCC . HCT : VM = 1.3 V; VI= GND to 3 V. The shaded areas indicate when the input is permitted to change for predictable output performance. The time allowed for the internal output of the latch to assume the state of the new data (tlatch) is important only when attempting to read from a location immediately after that location has received new data. This parameter is measured from the falling edge of WE to the rising edge of RA or RB,RE must be LOW.

Philips Semiconductors Product specification 4 x 4 register file; 3-state 74HC/HCT670 PACKAGE OUTLINES See “74HC/HCT/HCU/HCMOS Logic Package Outlines”. Fig.9 Waveforms showing the read enable (RE) to output (Qn) enable and disable times, and the read enable pulse width. (1) HC : V M = 50%; VI= GND to VCC . HCT : VM = 1.3 V; VI= GND to 3 V.