74HC6323A PHILIPS
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 15
Technical content
Product specification Supersedes data of December 1990 File under Integrated Circuits, IC06 September 1993 INTEGRATED CIRCUITS 74HC/HCT6323A Programmable ripple counter with oscillator; 3-state For a complete data sheet, please also download:
- The IC06 74HC/HCT/HCU/HCMOS Logic Family Specifications
- The IC06 74HC/HCT/HCU/HCMOS Logic Package Information
- The IC06 74HC/HCT/HCU/HCMOS Logic Package Outlines
Philips Semiconductors Product specification Programmable ripple counter with oscillator; 3-state 74HC/HCT6323A
FEATURES
- 8-pin space saving package
- Programmable 3-stage ripple counter
- Suitable for over-tone crystal application up to 50 MHz CC =5V ± 10%)
- 3-state output buffer
- Two internal capacitors
- Recommended operating range for use with third overtone crystals 3t o6V
- Oscillator stop function ( MR)
- Output capability: bus driver→ (15 LSTTL)
- ICC category: MSI.
APPLICATIONS
- Control counters
- Timers
- Frequency dividers
- Time-delay circuits
- CIO (Compact Integrated Oscillator)
- Third-overtone crystal operation. GENERAL DESCRIPTION The HC/HCT6323A are high-speed Si-gate CMOS devices. They are specified in compliance with JEDEC standard no. 7A. The HC/HCT6323A are oscillators designed for quartz crystal combined with a programmable 3-state counter, a 3-state output buffer and an overriding asynchronous master reset ( MR). With the two select inputs S1 and S2 the counter can be switched in the divide-by-1, 2, 4 or 8 mode. If left floating the clock is divided by 8. The oscillator is designed to operate either in the fundamental or third overtone mode depending on the crystal and external components applied. On-chip capacitors minimize external component count for third overtone crystal applications. The oscillator may be replaced by an external clock signal at input X1. In this event the other oscillator pin (X2) must be floating. The counter advances on the negative-going transition of X1. A LOW level on MR resets the counter, stops the oscillator and sets the output buffer in the 3-state condition.MR can be left floating since an internal pull-up resistor will make the MR inactive. In the HCT version, theMR input and the two mode select pins S1 and S2 are TTL compatible, but the X1 input has CMOS input switching levels and may be driven by a TTL output using a pull-up resistor connected to V CC . QUICK REFERENCE DATA GND = 0 V; Tamb = 25°C; tr = tf = 6 ns. Notes 1. C PD is used to determine the dynamic power dissipation (PD inµW): PD = (CPD x VCC 2 x fi) + (CL + VCC 2 x fo) + (Ipull-up x VCC ) where: fi = input frequency in MHz; fo = output frequency in MHz. VCC = supply voltage in V; CL = output load capacitance in pF. Ipull-up = pull-up currents inµA. 2. For HC and HCT an external clock is applied to X1 with: tr = tf≤ 6 ns, Vi is GND to VCC ,MR = HIGH Ipull-up is the summation of−II (µA) of S1 and S2 inputs at the LOW state.
ORDERING INFORMATION
SYMBOL PARAMETER CONDITIONS TYP. UNIT HC HCT tPHL /tPLH propagation delay X1 to OUT (S1 = S2 = LOW) C L = 15 pF; VCC = 5 V 17 17 ns fmax maximum clock frequency 90 90 MHz C I input capacitance except X1 and X2 3.5 3.5 pF C PD power dissipation capacitance per package +1; notes 1 and 2 54 54 pF +2; notes 1 and 2 42 42 pF +4; notes 1 and 2 36 36 pF +8; notes 1 and 2 33 33 pF EXTENDED TYPE NUMBER PACKAGE PINS PIN POSITION MATERIAL CODE 74HC/HCT6323AD 8 SO plastic SOT96
Philips Semiconductors Product specification Programmable ripple counter with oscillator; 3-state 74HC/HCT6323A PINNING SYMBOL PIN DESCRIPTION OUT 1 counter output S1 - S2 3, 2 mode select inputs for divide by 1, 2, 4 or 8 GND 4 ground (0 V) MR 5 master reset (active LOW) X2 6 oscillator pin X1 7 clock input/oscillator pin V CC 8 positive supply FUNCTION TABLE INPUTS OUTPUTS S1 S2 OUT 00 f i 01 f i/2 10 f i/4 11 f i/8 Fig.1 Pin configuration. handbook, halfpage MBA343 OUT GND VCC MR 6323A Fig.2 IEC logic symbol. handbook, halfpage MBA344 CP MR OUT C D Fig.3 Functional diagram. handbook, full pagewidth MBA350 OUTS1 S2MR C D CP 3 - STAGE BINARY COUNTER AND DECODER 32 1
Philips Semiconductors Product specification Programmable ripple counter with oscillator; 3-state 74HC/HCT6323A Fig.4 Logic diagram. Internal capacitors typical 7 pF each. Including stray capacitors on pin X1 and X2, total capacitance will be typical 12 pF per pin. handbook, full pagewidth MBA349 QCP FF R (1) V CC 7 pF(1) V 7 pF CC QCP FF R QCP FF R DECODER VCC OUT VCC MR VCC S1 S2
Philips Semiconductors Product specification Programmable ripple counter with oscillator; 3-state 74HC/HCT6323A DC CHARACTERISTICS FOR 74HC For the DC characteristics see“74HC/HCT/HCU/HCMOS Logic Family Specifications”. Output capability: non-standard; bus driver (except for X2) I CC category: MSI. Voltages are referenced to GND (ground = 0 V). DC CHARACTERISTICS FOR 74HC SYMBOL PARAMETER Tamb (°C) UNIT TEST CONDITION 25 −40 to 85 −40 to 125 VCC (V) VI OTHER MIN TYP MAX MIN MAX MIN MAX VIH HIGH level input voltage MR, X1 input 1.5 3.15 4.2 1.2 2.4 3.2 1.5 3.15 4.2 1.50 3.15 4.20 V V V 2.0 4.5 6.0 V IL LOW level input voltage MR, X1 input 0.8 2.1 2.8 0.5 1.35 1.80 0.5 1.35 1.8 0.5 1.35 1.8 V V V 2.0 4.5 6.0 V OH HIGH level output voltage X2 output 3.98 5.48 3.84 5.34 3.7 5.2 V V 4.5 6.0 X1 = GND and MR = VCC IO =−2.6 mA IO =−3.3 mA 3.98 5.48 3.84 5.34 3.7 5.2 V V 4.5 6.0 X1 = VCC and MR = GND IO =−2.6 mA IO =−3.3 mA 1.9 4.4 5.9 2.0 4.5 6.0 1.9 4.4 5.9 1.9 4.4 5.9 V V V 2.0 4.5 6.0 X1 = GND and MR = VCC −IO = 20µA IO =−20 µA IO =−20 µA 1.9 4.4 5.9 2.0 4.5 6.0 1.9 4.4 5.9 1.9 4.4 5.9 V V V 2.0 4.5 6.0 X1 = V CC and MR = GND IO =−20 µA IO =−20 µA IO =−20 µA VOH HIGH level output voltage OUT 1.9 4.4 5.9 2.0 4.5 6.0 1.9 4.4 5.9 1.9 4.4 5.9 V V V 2.0 4.5 6.0 V IH or VIL IO =−20 µA IO =−20 µA IO =−20 µA VOH HIGH level output voltage OUT 3.98 5.48 3.84 5.34 3.7 5.2 V V 4.5 6.0 V IH or VIL IO =−6 mA IO =−7.8 mA VOL LOW level output voltage X2 output 0.26 0.26 0.33 0.33 0.4 0.4 V V 4.5 6.0 X1 = V CC and MR = VCC IO = 2.6 mA IO = 3.3 mA 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 V V V 2.0 4.5 6.0 X1 = V CC and MR = VCC IO = 20µA IO = 20µA IO = 20µA VOL LOW level output voltage OUT 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 V V V 2.0 4.5 6.0 V IH or VIL IO = 20µA IO = 20µA IO = 20µA
Philips Semiconductors Product specification Programmable ripple counter with oscillator; 3-state 74HC/HCT6323A VOL LOW level output voltage OUT 0.26 0.26 0.33 0.33 0.4 0.4 V V 4.5 6.0 V IH or VIL IO = 6 mA IO = 7.8 mA ±ILI input leakage current X1 −− 0.1 − 1 − 1 µA 6.0 MR = VCC S1 = VCC S2 = VCC −II input pull-up current S1, S2 and MR 5 30 100 −−− −µ A 6.0 GND see Fig.11 and Fig.12 ICC quiescent supply current −− 8 − 80 − 160 µA 6.0 V CC or GND IO = 0 SYMBOL PARAMETER Tamb (°C) UNIT TEST CONDITION 25 −40 to 85 −40 to 125 VCC (V) VI OTHER MIN TYP MAX MIN MAX MIN MAX
Philips Semiconductors Product specification Programmable ripple counter with oscillator; 3-state 74HC/HCT6323A AC CHARACTERISTICS FOR 74HC GND = 0 V; tr = tf = 6 ns; CL = 50 pF. Note to the 74HC AC Characteristics 1. tPZH only applicable in the divide-by-1 mode and X1 must be HIGH. SYMBOL PARAMETER Tamb (°C) UNIT TEST CONDITION 25 −40 to 85 −40 to 125 VCC (V) VI OTHER MIN TYP MAX MIN MAX MIN MAX tPHL /tPLH propagation delay X1 to OUT divide by 1 185 230 275 ns ns ns 2.0 4.5 6.0 Fig.7 S1 = GND S2 = GND t PHL /tPLH propagation delay X1 to OUT divide by 2 235 290 350 ns ns ns 2.0 4.5 6.0 Fig.7 S1 = GND S2 = V CC tPHL /tPLH propagation delay X1 to OUT divide by 4 285 355 425 ns ns ns 2.0 4.5 6.0 Fig.7 S1 = V CC S2 = GND tPHL /tPLH propagation delay X1 to OUT divide by 8 105 335 415 500 100 ns ns ns 2.0 4.5 6.0 Fig.7 S1 = V CC S2 = VCC tPLZ /tPHZ 3-state output disable time MR to OUT 150 185 225 ns ns ns 2.0 4.5 6.0 Fig.8 t PZL 3-state output enable time MR to OUT 150 185 225 ns ns ns 2.0 4.5 6.0 Fig.8 t PZH 3-state output enable time MR to OUT 200 250 300 ns ns ns 2.0 4.5 6.0 Fig.8 note 1 t THL /tTLH output transition time ns ns ns 2.0 4.5 6.0 Fig.7 t W clock pulse width X1, HIGH or LOW 6.0 ns ns ns 2.0 4.5 6.0 Fig.7 t W master reset pulse width MR; LOW 100 120 ns ns ns 2.0 4.5 6.0 Fig.9 t rem removal time MR to X1 100 6.0 125 150 ns ns ns 2.0 4.5 6.0 Fig.9 f max maximum clock pulse frequency 100 6.6 MHz MHz MHz 2.0 4.5 6.0 Fig.7
Philips Semiconductors Product specification Programmable ripple counter with oscillator; 3-state 74HC/HCT6323A DC CHARACTERISTICS FOR 74HCT For the DC characteristics see“74HC/HCT/HCU/HCMOS Logic Family Specifications”. Output capability: bus driver (except for X2). I CC category: MSI. Voltages are referenced to GND (ground = 0 V). SYMBOL PARAMETER Tamb (°C) UNIT TEST CONDITION 25 −40 to 85 −40 to 125 VCC (V) VI OTHER MIN TYP MAX MIN MAX MIN MAX VIH HIGH level input voltage MR, S1 and S2 inputs to 5.5 V IL LOW level input voltage MR, S1 and S2 inputs to 5.5 V IH HIGH level input voltage X1 input 3.15 3.85 3.15 3.85 3.15 3.85 V V 4.5 5.5 V IL LOW level input voltage X1 input 1.35 1.65 1.35 1.65 1.35 1.65 V V 4.5 5.5 V OH HIGH level output voltage X2 output and MR = VCC IO =−2.6 mA 3.98 −− 3.84 − 3.7 − V 4.5 X1 = V CC and MR = GND IO =−2.6 mA and MR = VCC IO =−20 µA and MR = GND IO =−20 mA VOH HIGH level output voltage OUT IH or VIL IO =−20 µA VOH HIGH level output voltage OUT IH or VIL IO =−6 mA
Philips Semiconductors Product specification Programmable ripple counter with oscillator; 3-state 74HC/HCT6323A Note to the HCT DC Characteristics 1. The value of additional quiescent supply current (ΔICC ) for unit load of 1 is given in the family specifications. To determineΔICC per input, multiply this value by the unit load coefficient shown in the table below. UNIT LOAD COEFFICIENT VOL LOW level output voltage X2 output CC and MR = VCC IO = 2.6 mA − 0 0.1 − 0.1 − 0.1 V 4.5 X1 = V CC and MR = VCC IO = 20µA VOL LOW level output voltage OUT IH or VIL IO = 20µA VOL LOW level output voltage OUT IH or VIL IO = 6 mA ±ILI input leakage current S1 = VCC; S2 = VCC −II input pull-up current S1, S2 and MR 5 25 100 −−−−µ A 5.5 GND see Fig.11 and Fig.12 ICC quiescent supply current −− 8 − 80 − 160 µA 5.5 V CC or GND Io =0 ΔICC additional quiescent supply current per input pin for unit load coefficient is 1 − 100 360 − 450 − 490 µA 5.5 V CC or GND other inputs at VCC or GND; Io =0 ; (note 1) INPUT UNIT LOAD COEFFICIENT MR, S1, S2 0.40 SYMBOL PARAMETER Tamb (°C) UNIT TEST CONDITION 25 −40 to 85 −40 to 125 VCC (V) VI OTHER MIN TYP MAX MIN MAX MIN MAX
Philips Semiconductors Product specification Programmable ripple counter with oscillator; 3-state 74HC/HCT6323A AC CHARACTERISTICS FOR 74HCT GND = 0 V; tr = tf = 6 ns; CL = 50 pF Note to the 74HCT AC Characteristics 1. tPZH only applicable in the divide-by-1 mode and X1 must be HIGH. SYMBOL PARAMETER Tamb (°C) UNIT TEST CONDITION 25 −40 to 85 −40 to 125 VCC (V) VI OTHER MIN TYP MAX MIN MAX MIN MAX tPHL /tPLH propagation delay X1 to OUT divide-by-1 − 24 40 − 50 − 60 ns 4.5 Fig.7 S1 = GND S2 = GND t PHL /tPLH propagation delay X1 to OUT divide-by-2 − 29 50 − 62 − 75 ns 4.5 Fig.7 S1 = GND S2 = V CC tPHL /tPLH propagation delay X1 to OUT divide-by-4 − 35 60 − 75 − 90 ns 4.5 Fig.7 S1 = V CC S2 = GND tPHL /tPLH propagation delay X1 to OUT divide-by-8 − 40 70 − 87 − 105 ns 4.5 Fig.7 S1 = V CC S2 = VCC tPLZ /tPHZ 3-state output disable time MR to OUT − 21 35 − 43 − 52 ns 4.5 Fig.8 tPZ 3-state output enable time MR to OUT − 16 30 − 37 − 45 ns 4.5 Fig.8 tPZH 3-state output enable time MR to OUT − 22 38 − 47 − 57 ns 4.5 Fig.8 see note 1 tTHL /tTLH output transition time − 51 2 − 15 − 19 ns 4.5 Fig.7 tW clock pulse width X1, HIGH or LOW 10 6 − 12 − 15 − ns 4.5 Fig.7 t W master reset pulse width MR; LOW 16 8 − 20 − 24 − ns 4.5 Fig.9 trem removal time MR to X1 24 12 − 30 − 36 − ns 4.5 Fig.9 fmax maximum clock pulse frequency 50 85 − 40 − 33 − MHz 4.5 Fig.7
Philips Semiconductors Product specification Programmable ripple counter with oscillator; 3-state 74HC/HCT6323A Fig.5 Test set-up for measuring forward transconductance gfs = dio/dvi at vo is constant (see also Fig.6);MR = HIGH. handbook, halfpage MGA645 A output 100 F VCC input0.47 F R = 560 kΩbias io(f = 1 kHz) GND vi µ µ Fig.6 Typical forward transconductance gfs as a function of the supply voltage Vcc at Tamb =2 5°C. handbook, halfpage MBA331 0123456 gfs (mA/V) VCC (V) Fig.7 Waveforms showing the clock (X1) to output (OUT) propagation delays, the clock pulse width, the output transition times and the maximum clock frequency. (1) HC : VM = 50%; VI= GND to VCC . HCT : VM = 1.3 V; VI= GND to 3 V. handbook, full pagewidth tPHL V M (1) tTHL tTLH tW 1/f max tPLH OUT OUTPUT X1 INPUT MBA318 V M (1)
Philips Semiconductors Product specification Programmable ripple counter with oscillator; 3-state 74HC/HCT6323A Fig.8 Waveforms showing the inputMR to output OUT, 3-state enable and disable times. (1) HC : VM = 50%; VI= GND to VCC . HCT : VM = 1.3 V; VI= GND to 3 V. handbook, full pagewidth MBA319 tPLZ V M (1) tPZL V M (1) V M (1) outputs disabled outputs enabled tPZH 90 % tPHZ 10 % 90 % tf tr outputs enabled MR INPUT OUTPUT LOW - to - OFF OFF - to - LOW OUTPUT HIGH - to - OFF OFF - to - HIGH Fig.9 Waveforms showing theMR minimum pulse width andMR to X1 removal time. (1) HC : VM = 50%; VI= GND to VCC . HCT : VM = 1.3 V; VI= GND to 3 V. handbook, halfpage MBA323 VM (1) tW trem MR INPUT X1 INPUT V M (1)
Philips Semiconductors Product specification Programmable ripple counter with oscillator; 3-state 74HC/HCT6323A
APPLICATION INFORMATION
Fig.10 Power-on reset. The input pull-up current is used to create a power-on delay time atMR. handbook, halfpage MBA348 6323A MR Fig.11 Typical input pull-up current as a function of the input voltage (VI). handbook, halfpage MBA347 123456 VI (V) 2 V VCC = 6 V 4.3 V −II (µA) Fig.12 Typical input pull-up current as a function of the supply voltage (VCC ). handbook, halfpage MBA346 12345 6 VCC (V) −II (µA) VI = 0 V Table 1 Typical application values Table 2 Typical Application Values f (MHz) R2 (k Ω ) C1 (pF) C2 (pF) 1 4.7 47 to 68 10 2.2 47 to 68 25 1 33 33 f (MHz) R bias (kΩ ) C1 (pF) 50 3.0 4.7
Philips Semiconductors Product specification Programmable ripple counter with oscillator; 3-state 74HC/HCT6323A Fig.13 Typical setup for a crystal oscillator operating in the fundamental mode (1 MHz to 25 MHz). Above 5 MHz replace R2 by a capacitor of half the value of C2. C L at which a crystal is specified (or adjusted) equals for this application C1 . C2/C1 + C2. handbook, halfpage MBA328 - 1 R bias 100 kΩ to 1 M Ω R2 2.2 kΩ 100 pFC222 to 37 pFC1 X17 MR (from logic) Fig.14 Typical set-up for a crystal oscillator operating in the third overtone mode without the use of an inductor. Applicable for third overtone crystals (lower damping resistance at the third harmonic frequency) at typical 50 MHz. For lower frequencies extra load capacitors must be supplied, or increase bias resistor. handbook, halfpage MBA329 - 1 R bias 3 kΩ X17 MR (from logic) 1 to 10 pF (optional)
Philips Semiconductors Product specification Programmable ripple counter with oscillator; 3-state 74HC/HCT6323A Typical Crystal Oscillator In Fig.13, R2 is the power limiting resistor. For starting and maintaining oscillation a minimum transconductance is necessary, so R2 should not be too large. A practical value for R2 is 2.2 kΩ . The oscillator has been designed to operate over a wide frequency spectrum, for quartz crystals operating in the fundamental mode and in the overtone mode. The circuit is a Pierce type oscillator and requires a minimum of external components. There are two on-chip capacitors, X1 and X2, of approximately 7 pF. Together with the stray and input capacitance the value becomes 12 pF for 8-pin SO packages. These values are convenient and make it possible to run the oscillator in the third overtone without external capacitors applied. If a certain frequency is chosen, the IC parameters, as forward transconductance, and the crystal parameters such as the motional resistances R1 (fundamental), R3 (third overtone) and R5 (fifth overtone), are of paramount importance. Also the values of the external components as R s (series resistance) and the crystal load capacitances play an important role. Especially in overtone mode oscillations, R b (bias resistance) and the load capacitance values are very important. Considerations for Fundamental Oscillator: In the fundamental oscillator mode, the R b has only the function of biasing the inverter stage, so that it operates as an amplifier with a phase shift of approximately 180°. The value must be high, i.e. 100 kΩ up to 10 MΩ . The load capacitors C1 and C2, must have a value that is suitable for the crystal being used. The crystal is designed for a certain frequency having a specific load capacitance. C1 can be used to trim the oscillation frequency. The series resistance reduces the total loop gain. One function of it is therefore to reduce the power dissipation in the crystal. R s also suppresses overtone oscillations and introduces a phase shift over a broad frequency range. This is of less concern provided R s is not too high a value. Note A combination of a small load capacitor value and a small series resistance, may cause a third overtone oscillation. Considerations for Third-overtone Oscillator: In the overtone configuration, series resistance is no longer applied. This is essential otherwise the gain for third overtone can be too small for oscillation. A simple solution to suppress the fundamental oscillation, is to spoil the crystal fundamental activity. By dramatically reducing the value of the bias resistor of the inverting stage, and applying small load capacitors, it is possible to have an insufficient phase in the total loop for fundamental oscillation. However the phase for third overtone is good. It can be explained by the R b × Cl time constant. During oscillation the crystal with the load capacitors cause a phase shift of 180°. Because R b is parallel with the crystal (no Rs), Rb spoils the phase for fundamental. R b × Cl must be of a value, that it is not spoiling the phase for third overtone too much. Because third overtone is a 3 times higher frequency than the fundamental, the R b × Cl cannot 'maintain' the higher third overtone frequency, which results in a less spoiled overtone phase. PACKAGE OUTLINES See “74HC/HCT/HCU/HCMOS Logic Package Outlines”.