74HC595 NEXPERIA
Document overview
- PDF pages: 21
Technical content
Page 1
8-bit serial-in, serial or parallel-out shift register with output latches; 3-state
1. General description
The 74HC595; 74HCT595 is an 8-bit serial-in/serial or parallel-out shift register with a storage register and 3-state outputs. Both the shift and storage register have separate clocks. The device features a serial input (DS) and a serial output (Q7S) to enable cascading and an asynchronous reset MR input. A LOW on MR will reset the shift register. Data is shifted on the LOW-to-HIGH transitions of the SHCP input. The data in the shift register is transferred to the storage register on a LOW-to-HIGH transition of the STCP input. If both clocks are connected together, the shift register will always be one clock pulse ahead of the storage register. Data in the storage register
appears at the output whenever the output enable input (OE) is LOW. A HIGH on OE causes the outputs to assume a high-impedance OFF-state. Operation of the OE input does not affect the state of the registers. Inputs include clamp diodes. This enables the use of current limiting resistors to interface inputs to voltages in excess of VCC.
2. Features and benefits
- Wide supply voltage range from 2.0 to 6.0 V
- CMOS low power dissipation
- High noise immunity
- 8-bit serial input
- 8-bit serial or parallel output
- Storage register with 3-state outputs
- Shift register with direct clear
- 100 MHz (typical) shift out frequency
- Latch-up performance exceeds 100 mA per JESD 78 Class II Level B
- Complies with JEDEC standards:
- JESD8C (2.7 V to 3.6 V)
- JESD7A (2.0 V to 6.0 V)
- Input levels:
- For 74HC595: CMOS level
- For 74HCT595: TTL level
- ESD protection:
- HBM JESD22-A114F exceeds 2000 V
- MM JESD22-A115-A exceeds 200 V
- Multiple package options
- Specified from -40 °C to +85 °C and from -40 °C to +125 °C
3. Applications
- Serial-to-parallel data conversion
- Remote control holding register
Page 2
4. Ordering information
Table 1. Ordering information
| Type number | Package | |||
|---|---|---|---|---|
| Temperature range | Name | Description | Version | |
| 74HC595D | -40 °C to +125 °C | SO16 | plastic small outline package; 16 leads; body width 3.9 mm | SOT109-1 |
| 74HCT595D | ||||
| 74HC595PW | -40 °C to +125 °C | TSSOP16 | plastic thin shrink small outline package; 16 leads; body width 4.4 mm | SOT403-1 |
| 74HCT595PW | ||||
| 74HC595BQ | -40 °C to +125 °C | DHVQFN16 | plastic dual in-line compatible thermal enhanced very thin quad flat package; no leads; 16 terminals; body 2.5 × 3.5 × 0.85 mm | SOT763-1 |
| 74HCT595BQ | ||||
| 74HC595BZ | -40 °C to +125 °C | DHXQFN16 | plastic, leadless dual in-line compatible thermal enhanced extreme thin quad flat package; no leads; 16 terminals; 0.4 mm pitch; body 2 mm × 2.4 mm × 0.48 mm | SOT8016-1 |
5. Functional diagram
| 14 DS 11 SHCP 8-STAGE SHIFT REGISTER 10 MR Q7S 9 12 STCP 8-BIT STORAGE REGISTER 13 OE 3-STATE OUTPUTS Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 15 1 2 3 4 5 6 7 mna554 Fig. 1. Functional diagram | |
| 11 12 SHCP STCP 9 Q7S 15 Q0 1 Q1 2 Q2 14 3 DS Q3 4 Q4 5 Q5 6 Q6 7 Q7 MR OE 10 13 mna552 Fig. 2. Logic symbol | 13 EN3 12 C2 10 R SRG8 11 C1/ 14 15 1D 2D 3 1 2 3 4 5 6 7 9 mna553 Fig. 3. IEC logic symbol |
2 / 21
Page 3

6. Pinning information
6.1. Pinning

3 / 21
Page 4

6.2. Pin description
Table 2. Pin description
| Symbol | Pin | Description |
|---|---|---|
| Q0, Q1, Q2, Q3, Q4, Q5, Q6, Q7 | 15, 1, 2, 3, 4, 5, 6, 7 | parallel data output |
| GND | 8 | ground (0 V) |
| Q7S | 9 | serial data output |
| MR | 10 | master reset (active LOW) |
| SHCP | 11 | shift register clock input |
| STCP | 12 | storage register clock input |
| OE | 13 | output enable input (active LOW) |
| DS | 14 | serial data input |
| Q0 | 15 | parallel data output 0 |
| V CC | 16 | supply voltage |
4 / 21
Page 5
7. Functional description
Table 3. Function table H = HIGH voltage state; L = LOW voltage state; ↑ = LOW-to-HIGH transition; X = don’t care; NC = no change; Z = high-impedance OFF-state.
| Control | Input | Output | Function | ||||
| SHCP | STCP | OE | MR | DS | Q7S | Qn | |
| X | X | L | L | X | L | NC | a LOW-level on MR only affects the shift registers |
| X | ↑ | L | L | X | L | L | empty shift register loaded into storage register |
| X | X | H | L | X | L | Z | shift register clear; parallel outputs in high-impedance OFF-state |
| ↑ | X | L | H | H | Q6S | NC | logic HIGH-level shifted into shift register stage 0. Contents of all shift register stages shifted through, e.g. previous state of stage 6 (internal Q6S) appears on the serial output (Q7S). |
| X | ↑ | L | H | X | NC | QnS | contents of shift register stages (internal QnS) are transferred to the storage register and parallel output stages |
| ↑ | ↑ | L | H | X | Q6S | QnS | contents of shift register shifted through; previous contents of the shift register is transferred to the storage register and the parallel output stages |

5 / 21
Page 6
8. Limiting values
Table 4. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V).
| Symbol | Parameter | Conditions | Min | Max | Unit |
|---|---|---|---|---|---|
| V CC | supply voltage | -0.5 | +7 | V | |
| I IK | input clamping current | V < -0.5 V or V > V + 0.5 V I I CC | - | ±20 | mA |
| I OK | output clamping current | V < -0.5 V or V > V + 0.5 V O O CC | - | ±20 | mA |
| I O | output current | V = -0.5 V to (V + 0.5 V) O CC | |||
| pin Q7S | - | ±25 | mA | ||
| pins Qn | - | ±35 | mA | ||
| I CC | supply current | - | 70 | mA | |
| I GND | ground current | -70 | - | mA | |
| T stg | storage temperature | -65 | +150 | °C | |
| P tot | total power dissipation | SOT109-1; SOT403-1; SOT763-1 [1] | - | 500 | mW |
| SOT8016-1 | - | 250 | mW |
[1] For SOT109-1 (SO16) package: Ptot derates linearly with 12.4 mW/K above 110 °C. For SOT403-1 (TSSOP16) package: Ptot derates linearly with 8.5 mW/K above 91 °C. For SOT763-1 (DHVQFN16) package: Ptot derates linearly with 11.2 mW/K above 106 °C.
9. Recommended operating conditions
Table 5. Recommended operating conditions
| Symbol | Parameter | Conditions | 74HC595 | 74HCT595 | Unit | ||||
|---|---|---|---|---|---|---|---|---|---|
| Min | Typ | Max | Min | Typ | Max | ||||
| V CC | supply voltage | 2.0 | 5.0 | 6.0 | 4.5 | 5.0 | 5.5 | V | |
| V I | input voltage | 0 | - | V CC | 0 | - | V CC | V | |
| V O | output voltage | 0 | - | V CC | 0 | - | V CC | V | |
| Δt/ΔV | input transition rise and fall rate | V = 2.0 V CC | - | - | 625 | - | - | - | ns/V |
| V = 4.5 V CC | - | 1.67 | 139 | - | 1.67 | 139 | ns/V | ||
| V = 6.0 V CC | - | - | 83 | - | - | - | ns/V | ||
| T amb | ambient temperature | -40 | +25 | +125 | -40 | +25 | +125 | °C | |
6 / 21
Page 7
10. Static characteristics
Table 6. Static characteristics At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
| Symbol | Parameter | Conditions | -40 °C to +85 °C | -40 °C to +125 °C | Unit | |||
|---|---|---|---|---|---|---|---|---|
| Min | Typ | Max | Min | Max | ||||
| 74HC595 | ||||||||
| V IH | HIGH-level input voltage | V = 2.0 V CC | 1.5 | 1.2 | - | 1.5 | - | V |
| V = 4.5 V CC | 3.15 | 2.4 | - | 3.15 | - | V | ||
| V = 6.0 V CC | 4.2 | 3.2 | - | 4.2 | - | V | ||
| V IL | LOW-level input voltage | V = 2.0 V CC | - | 0.8 | 0.5 | - | 0.5 | V |
| V = 4.5 V CC | - | 2.1 | 1.35 | - | 1.35 | V | ||
| V = 6.0 V CC | - | 2.8 | 1.8 | - | 1.8 | V | ||
| V OH | HIGH-level output voltage | V = V or V I IH IL | ||||||
| all outputs | ||||||||
| I = -20 μA; V = 2.0 V O CC | 1.9 | 2.0 | - | 1.9 | - | V | ||
| I = -20 μA; V = 4.5 V O CC | 4.4 | 4.5 | - | 4.4 | - | V | ||
| I = -20 μA; V = 6.0 V O CC | 5.9 | 6.0 | - | 5.9 | - | V | ||
| Q7S output | ||||||||
| I = -4 mA; V = 4.5 V O CC | 3.84 | 4.32 | - | 3.7 | - | V | ||
| I = -5.2 mA; V = 6.0 V O CC | 5.34 | 5.81 | - | 5.2 | - | V | ||
| Qn bus driver outputs | ||||||||
| I = -6 mA; V = 4.5 V O CC | 3.84 | 4.32 | - | 3.7 | - | V | ||
| I = -7.8 mA; V = 6.0 V O CC | 5.34 | 5.81 | - | 5.2 | - | V | ||
| V OL | LOW-level output voltage | V = V or V I IH IL | ||||||
| all outputs | ||||||||
| I = 20 μA; V = 2.0 V O CC | - | 0 | 0.1 | - | 0.1 | V | ||
| I = 20 μA; V = 4.5 V O CC | - | 0 | 0.1 | - | 0.1 | V | ||
| I = 20 μA; V = 6.0 V O CC | - | 0 | 0.1 | - | 0.1 | V | ||
| Q7S output | ||||||||
| I = 4 mA; V = 4.5 V O CC | - | 0.15 | 0.33 | - | 0.4 | V | ||
| I = 5.2 mA; V = 6.0 V O CC | - | 0.16 | 0.33 | - | 0.4 | V | ||
| Qn bus driver outputs | ||||||||
| I = 6 mA; V = 4.5 V O CC | - | 0.15 | 0.33 | - | 0.4 | V | ||
| I = 7.8 mA; V = 6.0 V O CC | - | 0.16 | 0.33 | - | 0.4 | V | ||
| I I | input leakage current | V = V or GND; V = 6.0 V I CC CC | - | - | ±1.0 | - | ±1.0 | μA |
| I OZ | OFF-state output current | V = V or V ; V = 6.0 V; I IH IL CC V = V or GND O CC | - | - | ±5.0 | - | ±10 | μA |
| I CC | supply current | V = V or GND; I = 0 A; I CC O V = 6.0 V CC | - | - | 80 | - | 160 | μA |
| C I | input capacitance | - | 3.5 | - | - | - | pF | |
7 / 21
Page 8
| Symbol | Parameter | Conditions | -40 °C to +85 °C | -40 °C to +125 °C | Unit | |||
|---|---|---|---|---|---|---|---|---|
| Min | Typ | Max | Min | Max | ||||
| 74HCT595 | ||||||||
| V IH | HIGH-level input voltage | V = 4.5 V to 5.5 V CC | 2.0 | 1.6 | - | 2.0 | - | V |
| V IL | LOW-level input voltage | V = 4.5 V to 5.5 V CC | - | 1.2 | 0.8 | - | 0.8 | V |
| V OH | HIGH-level output voltage | V = V or V ; V = 4.5 V I IH IL CC | ||||||
| all outputs | ||||||||
| I = -20 μA O | 4.4 | 4.5 | - | 4.4 | - | V | ||
| Q7S output | ||||||||
| I = -4 mA O | 3.84 | 4.32 | - | 3.7 | - | V | ||
| Qn bus driver outputs | ||||||||
| I = -6 mA O | 3.7 | 4.32 | - | 3.7 | - | V | ||
| V OL | LOW-level output voltage | V = V or V ; V = 4.5 V I IH IL CC | ||||||
| all outputs | ||||||||
| I = 20 μA O | - | 0 | 0.1 | - | 0.1 | V | ||
| Q7S output | ||||||||
| I = 4.0 mA O | - | 0.15 | 0.33 | - | 0.4 | V | ||
| Qn bus driver outputs | ||||||||
| I = 6.0 mA O | - | 0.16 | 0.33 | - | 0.4 | V | ||
| I I | input leakage current | V = V or GND; V = 5.5 V I CC CC | - | - | ±1.0 | - | ±1.0 | μA |
| I OZ | OFF-state output current | V = V or V ; V = 5.5 V; I IH IL CC V = V or GND O CC | - | - | ±5.0 | - | ±10 | μA |
| I CC | supply current | V = V or GND; I = 0 A; I CC O V = 5.5 V CC | - | - | 80 | - | 160 | μA |
| ΔI CC | additional supply current | per input pin; other inputs at V or GND; CC I = 0 A; V = V - 2.1 V; O I CC V = 4.5 V to 5.5 V CC | ||||||
| pins MR, SHCP, STCP, OE | - | 150 | 675 | - | 735 | μA | ||
| pin DS | - | 25 | 113 | - | 123 | μA | ||
| C I | input capacitance | - | 3.5 | - | - | - | pF | |
8 / 21
Page 9
11. Dynamic characteristics
Table 7. Dynamic characteristics Voltages are referenced to GND (ground = 0 V); for test circuit see Fig. 14.
| Symbol | Parameter | Conditions | 25 °C | -40 °C to +85 °C | -40 °C to +125 °C | Unit | ||||
|---|---|---|---|---|---|---|---|---|---|---|
| Min | Typ[1] | Max | Min | Max | Min | Max | ||||
| 74HC595 | ||||||||||
| t pd | propagation delay | SHCP to Q7S; see Fig. 9 [2] | ||||||||
| V = 2 V CC | - | 52 | 160 | - | 200 | - | 240 | ns | ||
| V = 4.5 V CC | - | 19 | 32 | - | 40 | - | 48 | ns | ||
| V = 6 V CC | - | 15 | 27 | - | 34 | - | 41 | ns | ||
| STCP to Qn; see Fig. 10 [2] | ||||||||||
| V = 2 V CC | - | 55 | 175 | - | 220 | - | 265 | ns | ||
| V = 4.5 V CC | - | 20 | 35 | - | 44 | - | 53 | ns | ||
| V = 6 V CC | - | 16 | 30 | - | 37 | - | 45 | ns | ||
| t PHL | HIGH to LOW propagation delay | MR to Q7S; see Fig. 12 | ||||||||
| V = 2 V CC | - | 47 | 175 | - | 220 | - | 265 | ns | ||
| V = 4.5 V CC | - | 17 | 35 | - | 44 | - | 53 | ns | ||
| V = 6 V CC | - | 14 | 30 | - | 37 | - | 45 | ns | ||
| t en | enable time | OE to Qn; see Fig. 13 [3] | ||||||||
| V = 2 V CC | - | 47 | 150 | - | 190 | - | 225 | ns | ||
| V = 4.5 V CC | - | 17 | 30 | - | 38 | - | 45 | ns | ||
| V = 6 V CC | - | 14 | 26 | - | 33 | - | 38 | ns | ||
| t dis | disable time | OE to Qn; see Fig. 13 [4] | ||||||||
| V = 2 V CC | - | 41 | 150 | - | 190 | - | 225 | ns | ||
| V = 4.5 V CC | - | 15 | 30 | - | 38 | - | 45 | ns | ||
| V = 6 V CC | - | 12 | 27 | - | 33 | - | 38 | ns | ||
| t W | pulse width | SHCP HIGH or LOW; see Fig. 9 | ||||||||
| V = 2 V CC | 75 | 17 | - | 95 | - | 110 | - | ns | ||
| V = 4.5 V CC | 15 | 6 | - | 19 | - | 22 | - | ns | ||
| V = 6 V CC | 13 | 5 | - | 16 | - | 19 | - | ns | ||
| STCP HIGH or LOW; see Fig. 10 | ||||||||||
| V = 2 V CC | 75 | 11 | - | 95 | - | 110 | - | ns | ||
| V = 4.5 V CC | 15 | 4 | - | 19 | - | 22 | - | ns | ||
| V = 6 V CC | 13 | 3 | - | 16 | - | 19 | - | ns | ||
| MR LOW; see Fig. 12 | ||||||||||
| V = 2 V CC | 75 | 17 | - | 95 | - | 110 | - | ns | ||
| V = 4.5 V CC | 15 | 6 | - | 19 | - | 22 | - | ns | ||
| V = 6 V CC | 13 | 5 | - | 16 | - | 19 | - | ns | ||
9 / 21
Page 10
| Symbol | Parameter | Conditions | 25 °C | -40 °C to +85 °C | -40 °C to +125 °C | Unit | ||||
|---|---|---|---|---|---|---|---|---|---|---|
| Min | Typ[1] | Max | Min | Max | Min | Max | ||||
| t su | set-up time | DS to SHCP; see Fig. 11 | ||||||||
| V = 2 V CC | 50 | 11 | - | 65 | - | 75 | - | ns | ||
| V = 4.5 V CC | 10 | 4 | - | 13 | - | 15 | - | ns | ||
| V = 6 V CC | 9 | 3 | - | 11 | - | 13 | - | ns | ||
| SHCP to STCP; see Fig. 11 | ||||||||||
| V = 2 V CC | 75 | 22 | - | 95 | - | 110 | - | ns | ||
| V = 4.5 V CC | 15 | 8 | - | 19 | - | 22 | - | ns | ||
| V = 6 V CC | 13 | 7 | - | 16 | - | 19 | - | ns | ||
| t h | hold time | DS to SHCP; see Fig. 11 | ||||||||
| V = 2 V CC | 3 | -6 | - | 3 | - | 3 | - | ns | ||
| V = 4.5 V CC | 3 | -2 | - | 3 | - | 3 | - | ns | ||
| V = 6 V CC | 3 | -2 | - | 3 | - | 3 | - | ns | ||
| t rec | recovery time | MR to SHCP; see Fig. 12 | ||||||||
| V = 2 V CC | 50 | -19 | - | 65 | - | 75 | - | ns | ||
| V = 4.5 V CC | 10 | -7 | - | 13 | - | 15 | - | ns | ||
| V = 6 V CC | 9 | -6 | - | 11 | - | 13 | - | ns | ||
| f max | maximum frequency | SHCP or STCP; see Fig. 9 and Fig. 10 | ||||||||
| V = 2 V CC | 9 | 30 | - | 4.8 | - | 4 | - | MHz | ||
| V = 4.5 V CC | 30 | 91 | - | 24 | - | 20 | - | MHz | ||
| V = 6 V CC | 35 | 108 | - | 28 | - | 24 | - | MHz | ||
| C PD | power dissipation capacitance | f = 1 MHz; V = GND to V [5] i I CC [6] | - | 115 | - | - | - | - | - | pF |
| 74HCT595; V = 4.5 V to 5.5 V CC | ||||||||||
| t pd | propagation delay | SHCP to Q7S; see Fig. 9 [2] | - | 25 | 42 | - | 53 | - | 63 | ns |
| STCP to Qn; see Fig. 10 [2] | - | 24 | 40 | - | 50 | - | 60 | ns | ||
| t PHL | HIGH to LOW propagation delay | MR to Q7S; see Fig. 12 | - | 23 | 40 | - | 50 | - | 60 | ns |
| t en | enable time | OE to Qn; see Fig. 13 [3] | - | 21 | 35 | - | 44 | - | 53 | ns |
| t dis | disable time | OE to Qn; see Fig. 13 [4] | - | 18 | 30 | - | 38 | - | 45 | ns |
| t W | pulse width | SHCP HIGH or LOW; see Fig. 9 | 16 | 6 | - | 20 | - | 24 | - | ns |
| STCP HIGH or LOW; see Fig. 10 | 16 | 5 | - | 20 | - | 24 | - | ns | ||
| MR LOW; see Fig. 12 | 20 | 8 | - | 25 | - | 30 | - | ns | ||
| t su | set-up time | DS to SHCP; see Fig. 11 | 16 | 5 | - | 20 | - | 24 | - | ns |
| SHCP to STCP; see Fig. 11 | 16 | 8 | - | 20 | - | 24 | - | ns | ||
10 / 21
Page 11
| Symbol | Parameter | Conditions | 25 °C | -40 °C to +85 °C | -40 °C to +125 °C | Unit | ||||
|---|---|---|---|---|---|---|---|---|---|---|
| Min | Typ[1] | Max | Min | Max | Min | Max | ||||
| t h | hold time | DS to SHCP; see Fig. 11 | 3 | -2 | - | 3 | - | 3 | - | ns |
| t rec | recovery time | MR to SHCP; see Fig. 12 | 10 | -7 | - | 13 | - | 15 | - | ns |
| f max | maximum frequency | SHCP and STCP; see Fig. 9 and Fig. 10 | 30 | 52 | - | 24 | - | 20 | - | MHz |
| C PD | power dissipation capacitance | f = 1 MHz; [5] i V = GND to V - 1.5 V [6] I CC | - | 130 | - | - | - | - | - | pF |
[1] Typical values are measured at nominal supply voltage. [2] tpd is the same as tPHL and tPLH. [3] ten is the same as tPZL and tPZH. [4] tdis is the same as tPLZ and tPHZ. [5] CPD is used to determine the dynamic power dissipation (PD in μW). PD = CPD × VCC 2 × fi + Σ(CL × VCC 2 × fo) where: fi = input frequency in MHz; fo = output frequency in MHz; Σ(CL × VCC 2 × fo) = sum of outputs; CL = output load capacitance in pF; VCC = supply voltage in V. [6] All 9 outputs switching.
11.1. Waveforms and test circuit

11 / 21
Page 12

12 / 21
Page 13

Table 8. Measurement points
| Type | Input | Output |
|---|---|---|
| V M | V M | |
| 74HC595 | 0.5V CC | 0.5V CC |
| 74HCT595 | 1.3 V | 1.3 V |
13 / 21
Page 14

Table 9. Test data
| Type | Input | Load | S1 position | ||||
|---|---|---|---|---|---|---|---|
| V I | t, t r f | C L | R L | t , t PHL PLH | t , t PZH PHZ | t , t PZL PLZ | |
| 74HC595 | V CC | 6 ns | 50 pF | 1 kΩ | open | GND | V CC |
| 74HCT595 | 3 V | 6 ns | 50 pF | 1 kΩ | open | GND | V CC |
14 / 21
Page 15
12. Package outline
SO16: plastic small outline package; 16 leads; body width 3.9 mm
SOT109-1


Note 1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included.

Fig. 15. Package outline SOT109-1 (SO16)
15 / 21
Page 16
TSSOP16: plastic thin shrink small outline package; 16 leads; body width 4.4 mm
SOT403-1



Fig. 16. Package outline SOT403-1 (TSSOP16)
16 / 21
Page 17
DHVQFN16: plastic dual in-line compatible thermal enhanced very thin quad flat package; no leads;
SOT763-1
16 terminals; body 2.5 x 3.5 x 0.85 mm


Note 1. Plastic or metal protrusions of 0.075 mm maximum per side are not included.
| OUTLINE VERSION | REFERENCES | EUROPEAN PROJECTION | ISSUE DATE | |||
| IEC | JEDEC | JEITA | ||||
| SOT763-1 | - - - | MO-241 | - - - | 02-10-17 03-01-27 | ||
Fig. 17. Package outline SOT763-1 (DHVQFN16)
17 / 21
Page 18
DHXQFN16: plastic, leadless dual in-line compatible thermal enhanced extreme thin quad flat package; no leads; 16 terminals; 0.4 mm pitch; body 2 mm x 2.4 mm x 0.48 mm
SOT8016-1

Fig. 18. Package outline SOT8016-1 (DHXQFN16)
18 / 21
Page 19
13. Abbreviations
Table 10. Abbreviations
| Acronym | Description |
|---|---|
| CMOS | Complementary Metal-Oxide Semiconductor |
| DUT | Device Under Test |
| ESD | ElectroStatic Discharge |
| HBM | Human Body Model |
| MM | Machine Model |
| TTL | Transistor-Transistor Logic |
14. Revision history
Table 11. Revision history
| Document ID | Release date | Data sheet status | Change notice | Supersedes |
| 74HC_HCT595 v.11 | 20210910 | Product data sheet | - | 74HC_HCT595 v.10 |
| Modifications: | • Type numbers 74HC595DB and 74HCT595DB (SOT338-1/SSOP16) removed. • Section 2updated. | |||
| 74HC_HCT595 v.10 | 20210429 | Product data sheet | - | 74HC_HCT595 v.9 |
| Modifications: | • Type number 74HC595BZ (SOT8016-1 / DHXQFN16) added. • Table 4: Derating values for P total power dissipation updated. tot | |||
| 74HC_HCT595 v.9 | 20170228 | Product data sheet | - | 74HC_HCT595 v.8 |
| Modifications: | • The format of this data sheet has been redesigned to comply with the identity guidelines of Nexperia. • Legal texts have been adapted to the new company name where appropriate. | |||
| 74HC_HCT595 v.8 | 20160225 | Product data sheet | - | 74HC_HCT595 v.7 |
| Modifications: | • Type numbers 74HC595N and 74HCT595N (SOT38-4) removed. | |||
| 74HC_HCT595 v.7 | 20150126 | Product data sheet | - | 74HC_HCT595 v.6 |
| Modifications: | • Table 7: Power dissipation capacitance condition for 74HCT595 is corrected. | |||
| 74HC_HCT595 v.6 | 20111212 | Product data sheet | - | 74HC_HCT595 v.5 |
| Modifications: | • Legal pages updated. | |||
| 74HC_HCT595 v.5 | 20110628 | Product data sheet | - | 74HC_HCT595 v.4 |
| 74HC_HCT595 v.4 | 20030604 | Product specification | - | 74HC_HCT595_CNV v.3 |
| 74HC_HCT595_CNV v.3 | 19980604 | Product specification | - | - |
19 / 21
Page 20
15. Legal information
Data sheet status
| Document status [1][2] | Product status [3] | Definition |
| Objective [short] data sheet | Development | This document contains data from the objective specification for product development. |
| Preliminary [short] data sheet | Qualification | This document contains data from the preliminary specification. |
| Product [short] data sheet | Production | This document contains the product specification. |
[1] Please consult the most recently issued document before initiating or completing a design. [2] The term 'short data sheet' is explained in section "Definitions". [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the internet at https://www.nexperia.com.
Definitions
Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. Nexperia does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information.
Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local Nexperia sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail.
Product specification — The information and data provided in a Product data sheet shall define the specification of the product as agreed between Nexperia and its customer, unless Nexperia and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the Nexperia product is deemed to offer functions and qualities beyond those described in the Product data sheet.
Disclaimers
Limited warranty and liability — Information in this document is believed to be accurate and reliable. However, Nexperia does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Nexperia takes no responsibility for the content in this document if provided by an information source outside of Nexperia.
In no event shall Nexperia be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory.
Notwithstanding any damages that customer might incur for any reason whatsoever, Nexperia’s aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of Nexperia.
Right to make changes — Nexperia reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof.
Suitability for use — Nexperia products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an Nexperia product can reasonably be expected to result in personal
injury, death or severe property or environmental damage. Nexperia and its suppliers accept no liability for inclusion and/or use of Nexperia products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk.
Quick reference data — The Quick reference data is an extract of the product data given in the Limiting values and Characteristics sections of this document, and as such is not complete, exhaustive or legally binding.
Applications — Applications that are described herein for any of these products are for illustrative purposes only. Nexperia makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification.
Customers are responsible for the design and operation of their applications and products using Nexperia products, and Nexperia accepts no liability for any assistance with applications or customer product design. It is customer’s sole responsibility to determine whether the Nexperia product is suitable and fit for the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products.
Nexperia does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s applications or products, or the application or use by customer’s third party customer(s). Customer is responsible for doing all necessary testing for the customer’s applications and products using Nexperia products in order to avoid a default of the applications and the products or of the application or use by customer’s third party customer(s). Nexperia does not accept any liability in this respect.
Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device.
Terms and conditions of commercial sale — Nexperia products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nexperia.com/profile/terms, unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. Nexperia hereby expressly objects to applying the customer’s general terms and conditions with regard to the purchase of Nexperia products by customer.
No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights.
Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities.
Non-automotive qualified products — Unless this data sheet expressly states that this specific Nexperia product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. Nexperia accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications.
In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without Nexperia’s warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond Nexperia’s specifications such use shall be solely at customer’s own risk, and (c) customer fully indemnifies Nexperia for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond Nexperia’s standard warranty and Nexperia’s product specifications.
Translations — A non-English (translated) version of a document is for reference only. The English version shall prevail in case of any discrepancy between the translated and English versions.
Trademarks
Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners.
20 / 21
Page 21
Contents
- General description......................................................1 2. Features and benefits.................................................. 1 3. Applications.................................................................. 1 4. Ordering information....................................................2 5. Functional diagram.......................................................2 6. Pinning information......................................................3 6.1. Pinning.........................................................................3 6.2. Pin description.............................................................4 7. Functional description................................................. 5
- Limiting values............................................................. 6 9. Recommended operating conditions..........................6 10. Static characteristics..................................................7 11. Dynamic characteristics.............................................9 11.1. Waveforms and test circuit.......................................11 12. Package outline........................................................ 15 13. Abbreviations............................................................19 14. Revision history........................................................19 15. Legal information......................................................20
For more information, please visit: http://www.nexperia.com For sales office addresses, please send an email to: salesaddresses@nexperia.com Date of release: 10 September 2021
21 / 21