74HC590 NXP

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 21

Technical content

power Schottky TTL (LSTTL). It is specified in compliance with JEDEC standard no. 7A. are connected together, the counter state always is one count ahead of the register. Table 1. Ordering information

74HC590_2 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 02 — 28 April 2009 2 of 21 NXP Semiconductors 74HC590 8-bit binary counter with output register; 3-state 4. Functional diagram Fig 1. Functional diagram 001aac542 CPR CE CPC MRC 8-BIT BINARY COUNTER 8-BIT STORAGE REGISTER OE 3-STATE OUTPUTS Q0 15 9RCO Fig 2. Logic symbol Fig 3. IEC logic symbol 001aac544 RCO OEMRC CPC CE CPR 11 13 1410 001aac545 12 G1 1D 2D 15

10 CT=0

9 RCO

14 EN3

(CT=255)Z4 MRC CE OE

74HC590_2 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 02 — 28 April 2009 3 of 21 NXP Semiconductors 74HC590 8-bit binary counter with output register; 3-state Fig 4. Logic diagram T R RCO T R 1 Q1 T R 2 Q2 T R 3 Q3 T R 4 Q4 T R 5 Q5 T R 6 Q6 T R 7 Q7 MRC CPC CE CPR OE 001aac543

74HC590_2 © NXP B.V. 2009. All rights reserved.

5.1 Pinning

5.2 Pin description

Table 2. Pin description

74HC590_2 © NXP B.V. 2009. All rights reserved. Table 3. Function table[1][2]

74HC590_2 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 02 — 28 April 2009 6 of 21 NXP Semiconductors 74HC590 8-bit binary counter with output register; 3-state Fig 8. Typical timing sequence 001aac548 CPC CPR MRC CE OE RCO counter clearinhibitcount high-impedance OFF-state

74HC590_2 © NXP B.V. 2009. All rights reserved. [1] The input and output voltage ratings may be exceeded if the input and output current ratings are observed. [2] For DIP16 package: Ptot derates linearly with 12 mW/K above 70°C. For SO16 packages: Ptot derates linearly with 8 mW/K above 70°C. For TSSOP16 packages: Ptot derates linearly with 5.5 mW/K above 60°C. For DHVQFN16 packages: Ptot derates linearly with 8 mW/K above 60°C.

  1. Recommended operating conditions

Table 4. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V).

74HC590_2 © NXP B.V. 2009. All rights reserved. Table 6. Static characteristics At recommended operating conditions; voltages are referenced to GND (ground = 0 V).

74HC590_2 © NXP B.V. 2009. All rights reserved. Table 7. Dynamic characteristics GND (ground = 0 V); for test circuit seeFigure15.

74HC590_2 © NXP B.V. 2009. All rights reserved. [1] tpd is the same as tPHL , tPLH . [2] ten is the same as tPZH and tPZL . [3] tdis is the same as tPLZ and tPHZ . [4] C PD is used to determine the dynamic power dissipation (PD inµW). L × VCC 2 × fo) = sum of outputs. Table 7. Dynamic characteristics …continued GND (ground = 0 V); for test circuit seeFigure15.

74HC590_2 © NXP B.V. 2009. All rights reserved. Measurement points are given inTable8. VOL and VOH are the typical output voltage levels that occur with the output load. Table 8. Measurement points Measurement points are given inTable8. VOL and VOH are the typical output voltage levels that occur with the output load.

74HC590_2 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 02 — 28 April 2009 12 of 21 NXP Semiconductors 74HC590 8-bit binary counter with output register; 3-state Measurement points are given inTable8. VOL and VOH are the typical output voltage levels that occur with the output load. Fig 11. Waveforms showing the propagation delays from the master reset counter input (MRC) to output (RCO), theMRC pulse width and recovery time 001aac551 tW tPLH trec VI GND VOH VOL RCO output MRC input VI GND CPC input VM VM VM Measurement points are given inTable8. VOL and VOH are the typical output voltage levels that occur with the output load. Fig 12. Waveforms showing the 3-state enable and disable times 001aac554 tPLZ tPHZ outputs disabled outputs enabled 90 % 10 % outputs enabled OE input VI VCC VOL VOH GND GND VM tPZL tPZH VM VM output LOW-to-OFF OFF-to-LOW output HIGH-to-OFF OFF-to-HIGH

74HC590_2 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 02 — 28 April 2009 13 of 21 NXP Semiconductors 74HC590 8-bit binary counter with output register; 3-state Measurement points are given inTable8. VOL and VOH are the typical output voltage levels that occur with the output load. Fig 13. Waveforms showing the set-up and hold times for the count enable input (CE) to the counter clock input (CPC) 001aac553 VI VM tsu tsu thth VM GND CPC input CE input VOH VOL Measurement points are given inTable8. VOL and VOH are the typical output voltage levels that occur with the output load. Fig 14. Waveforms showing the set-up and hold times for the counter clock input (CPC) to the register clock input (CPR) 001aac552 VI VM tsu th VM GND CPR input CPC input VOH VOL

74HC590_2 © NXP B.V. 2009. All rights reserved. Test data is given inTable9. T = Termination resistance should be equal to output impedance Zo of the pulse generator. C L = Load capacitance including jig and probe capacitance. Table 9. Test data

74HC590_2 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 02 — 28 April 2009 15 of 21 NXP Semiconductors 74HC590 8-bit binary counter with output register; 3-state 12. Package outline Fig 16. Package outline SOT38-4 (DIP16) REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA SOT38-4 95-01-14 03-02-13 M H c (e )1 M E A L seating plane w M e D A 2 Z E pin 1 index b 0 5 10 mm scale Note 1. Plastic or metal protrusions of 0.25 mm (0.01 inch) maximum per side are not included. UNIT A max. 12 b1 (1) (1) (1) b2 cD E e M ZHL mm DIMENSIONS (inch dimensions are derived from the original mm dimensions) A min. A max. b max.wM Ee1 1.73 1.30 0.53 0.38 0.36 0.23 19.50 18.55 6.48 6.20 3.60 7.80 10.0 inches 0.068 0.051 0.021 0.015 0.014 0.009 1.25 0.85 0.049 0.033 0.77 0.73 0.26 0.24 0.14 0.31 0.39 DIP16: plastic dual in-line package; 16 leads (300 mil) SOT38-4

74HC590_2 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 02 — 28 April 2009 16 of 21 NXP Semiconductors 74HC590 8-bit binary counter with output register; 3-state Fig 17. Package outline SOT109-1 (SO16) X w M q AA 1 A 2 bp D H E Lp Q detail X E Z e c L v M A (A )3 A y pin 1 index UNIT A max. A 1 A 2 A 3 bp cD (1) E (1) (1)eH E LL p QZ ywv q REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm inches 1.75 0.25 0.10 1.45 1.25 0.25 0.49 0.36 0.25 0.19 10.0 9.8 4.0 3.8 1.27 6.2 5.8 0.7 0.6 0.7 0.3 8 o o 0.25 0.1 DIMENSIONS (inch dimensions are derived from the original mm dimensions) Note 1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included. 1.0 0.4 SOT109-1 99-12-27 03-02-19 076E07 MS-012 0.069 0.010 0.004 0.057 0.049 0.01 0.019 0.014 0.0100 0.0075 0.39 0.38 0.16 0.15 0.05 1.05 0.0410.244 0.228 0.028 0.020 0.028 0.0120.01 0.25 0.01 0.0040.039 0.016 0 2.5 5 mm scale SO16: plastic small outline package; 16 leads; body width 3.9 mm SOT109-1

74HC590_2 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 02 — 28 April 2009 17 of 21 NXP Semiconductors 74HC590 8-bit binary counter with output register; 3-state Fig 18. Package outline SOT403-1 (TSSOP16) UNIT A 1 A 2 A 3 bp cD (1) E (2) (1)eH E LL p QZ ywv q REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm 0.15 0.05 0.95 0.80 0.30 0.19 0.2 0.1 5.1 4.9 4.5 4.3 0.65 6.6 6.2 0.4 0.3 0.40 0.06 o o0.13 0.10.21 DIMENSIONS (mm are the original dimensions) Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included. 0.75 0.50 SOT403-1 MO-153 99-12-27 03-02-18 w M bp D Z e 0.25 16 9 q AA 1 A 2 Lp Q detail X L (A )3 H E E c v M A XA y 0 2.5 5 mm scale TSSOP16: plastic thin shrink small outline package; 16 leads; body width 4.4 mm SOT403-1 A max. 1.1 pin 1 index

74HC590_2 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 02 — 28 April 2009 18 of 21 NXP Semiconductors 74HC590 8-bit binary counter with output register; 3-state Fig 19. Package outline SOT763-1 (DHVQFN16) terminal 1 index area 0.51 A 1 EhbUNIT ye 0.2 c REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm 3.6 3.4 D h 2.15 1.85 2.6 2.4 1.15 0.85 2.50.30 0.18 0.05 0.00 0.05 0.1 DIMENSIONS (mm are the original dimensions) 0.5 0.3 L 0.1 v 0.05 w 0 2.5 5 mm scale SOT763-1 DHVQFN16: plastic dual in-line compatible thermal enhanced very thin quad flat package; no leads; 16 terminals; body 2.5 x 3.5 x 0.85 mm A (1) max. A c detail X yy1 Ce L Eh D h e b 15 10 X D E C B A terminal 1 index area AC C Bv M w M E (1) Note 1. Plastic or metal protrusions of 0.075 mm maximum per side are not included. D (1) 02-10-17 03-01-27

74HC590_2 © NXP B.V. 2009. All rights reserved. Table 10. Abbreviations Table 11. Revision history

  • The format of this data sheet has been redesigned to comply with the new identity guidelines of NXP Semiconductors.
  • Legal texts have been adapted to the new company name where appropriate.
  • Quick reference data incorporated in toSection9 andSection10.
  • Added type number 74HC590N (DIP16 package) 74HC590_1 20050330 Product data sheet - -

74HC590_2 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 02 — 28 April 2009 20 of 21 NXP Semiconductors 74HC590 8-bit binary counter with output register; 3-state 15. Legal information

15.1 Data sheet status

[1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com.

15.2 Definitions

Draft —The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet —A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail.

15.3 Disclaimers

General — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Right to make changes —NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use —NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications —Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Limiting values —Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) may cause permanent damage to the device. Limiting values are stress ratings only and operation of the device at these or any other conditions above those given in the Characteristics sections of this document is not implied. Exposure to limiting values for extended periods may affect device reliability. Terms and conditions of sale —NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms , including those pertaining to warranty, intellectual property rights infringement and limitation of liability, unless explicitly otherwise agreed to in writing by NXP Semiconductors. In case of any inconsistency or conflict between information in this document and such terms and conditions, the latter will prevail. No offer to sell or license —Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. Export control —This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from national authorities.

15.4 Trademarks

Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 16. Contact information For more information, please visit:http://www.nxp.com For sales office addresses, please send an email to:salesaddresses@nxp.com Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification.

NXP Semiconductors 74HC590 8-bit binary counter with output register; 3-state © NXP B.V. 2009. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 28 April 2009 Document identifier: 74HC590_2 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. 17. Contents