74HC4066FT TOSHIBA
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 12
Technical content
CMOS Digital Integrated Circuits Silicon Monolithic 74HC4066FT Start of commercial production 2020-07 1. Functional Description
- Quad Bilateral Switch 2. General The 74HC4066FT is a high speed CMOS QUAD BILATERAL SWITCH fabricated with silicon gate CMOS technology. It consists of four independent high speed switches capable of controlling either digital or analog signals while maintaining the CMOS low power dissipation. Control input (C) is provided to control the switch. The switch turns ON while the C input is high, and the switch turns OFF while low. All inputs are equipped with protection circuits against static discharge or transient excess voltage. 3. Features (1) Wide operating temperature range: Topr = -40 to 125 (2) Low power dissipation: ICC = 1.0 µA (max) at VCC = 6.0 V, Ta = 25 (3) High noise immunity: VNIH = VNIL = 28 % VCC (min) (4) Low ON resistance: RON = 50 Ω (typ.) at VCC = 9.0 V, VI/O = VCC or GND (5) High degree of linearity: THD = 0.05 % (typ.) at VCC = 4.5 V 4. Packaging TSSOP14B 2020-11-05 Rev.1.0 ©2020 Toshiba Electronic Devices & Storage Corporation
- Pin Assignment 6. Marking 7. Truth Table Control H L Switch Function On Off 8. System Diagram (per circuit) 2020-11-05 Rev.1.0 ©2020 Toshiba Electronic Devices & Storage Corporation
- Absolute Maximum Ratings (Note) Characteristics Supply voltage Input voltage Switch I/O voltage Input diode current I/O diode current Switch through current VCC/ground current Power dissipation Storage temperature Symbol VCC VIN VI/O IIK II/OK IT ICC PD Tstg Note (Note 1) Rating -0.5 to 13.0 -0.5 to VCC + 0.5 -0.5 to VCC + 0.5 ±20 ±20 ±25 ±50 180 -65 to 150 Unit V V V mA mA mA mA mW Note: Exceeding any of the absolute maximum ratings, even briefly, lead to deterioration in IC performance or even destruction. Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings and the operating ranges. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Note 1: 180 mW in the range of T a = -40 to 85 . From Ta = 85 to 125 a derating factor of -3.25 mW/ shall be applied until 50 mW. 10. Operating Ranges (Note) Characteristics Supply voltage Input voltage Switch I/O voltage Operating temperature Input rise and fall times Symbol VCC VIN VI/O Topr tr,tf Rating 2.0 to 12 0 to VCC 0 to VCC -40 to 125 0 to 50 Unit V V V µs Note: The operating ranges must be maintained to ensure the normal operation of the device. Unused inputs must be tied to either VCC or GND. 2020-11-05 Rev.1.0 ©2020 Toshiba Electronic Devices & Storage Corporation
- Electrical Characteristics 11.1. DC Characteristics (Unless otherwise specified, T a = 25 ) Characteristics High-level input voltage Low-level input voltage ON-resistance Difference of ON-resistance between switches Input/Output leakage current (Switch OFF) Input/Output leakage current (Switch ON, output open) Control input leakage current Quiescent supply current Symbol VIH VIL RON ∆RON IOFF II/O IIN ICC Test Condition VIN = VIH VI/O = VCC to GND II/O ≤ 1 mA VIN = VIH VI/O = VCC or GND II/O ≤ 1 mA VIN = VIH VI/O = VCC to GND II/O ≤ 1 mA VOS = VCC or GND VIS = GND to VCC VIN = VIL VOS = VCC or GND VIN = VIH VIN = VCC or GND VIN = VCC or GND VCC (V) 2.0 4.5 9.0 12.0 2.0 4.5 9.0 12.0 4.5 9.0 12.0 2.0 4.5 9.0 12.0 4.5 9.0 12.0 12.0 12.0 12.0 6.0 9.0 12.0 Min 1.50 3.15 6.30 8.40 Typ. 160 Max 0.50 1.35 2.70 3.60 170 100 ±0.1 ±0.1 ±0.1 1.0 4.0 8.0 Unit V V Ω Ω µA µA µA µA 2020-11-05 Rev.1.0 ©2020 Toshiba Electronic Devices & Storage Corporation
11.2. DC Characteristics (Unless otherwise specified, T a = -40 to 85 ) Characteristics High-level input voltage Low-level input voltage ON-resistance Difference of ON-resistance between switches Input/Output leakage current (Switch OFF) Input/Output leakage current (Switch ON, output open) Control input leakage current Quiescent supply current Symbol VIH VIL RON ∆RON IOFF II/O IIN ICC Test Condition VIN = VIH VI/O = VCC to GND II/O ≤ 1 mA VIN = VIH VI/O = VCC or GND II/O ≤ 1 mA VIN = VIH VI/O = VCC to GND II/O ≤ 1 mA VOS = VCC or GND VIS = GND to VCC VIN = VIL VOS = VCC or GND VIN = VIH VIN = VCC or GND VIN = VCC or GND VCC (V) 2.0 4.5 9.0 12.0 2.0 4.5 9.0 12.0 4.5 9.0 12.0 4.5 9.0 12.0 4.5 9.0 12.0 12.0 12.0 12.0 6.0 9.0 12.0 Min 1.50 3.15 6.30 8.40 Max 0.50 1.35 2.70 3.60 200 100 130 ±1.0 ±1.0 ±1.0 10.0 40.0 80.0 Unit V V Ω Ω µA µA µA µA 2020-11-05 Rev.1.0 ©2020 Toshiba Electronic Devices & Storage Corporation
11.3. DC Characteristics (Unless otherwise specified, T a = -40 to 125 ) Characteristics High-level input voltage Low-level input voltage ON-resistance Difference of ON-resistance between switches Input/Output leakage current (Switch OFF) Input/Output leakage current (Switch ON, output open) Control input leakage current Quiescent supply current Symbol VIH VIL RON ∆RON IOFF II/O IIN ICC Test Condition VIN = VIH VI/O = VCC to GND II/O ≤ 1 mA VIN = VIH VI/O = VCC or GND II/O ≤ 1 mA VIN = VIH VI/O = VCC to GND II/O ≤ 1 mA VOS = VCC or GND VIS = GND to VCC VIN = VIL VOS = VCC or GND VIN = VIH VIN = 0 to 5.5 V VIN = VCC or GND VCC (V) 2.0 4.5 9.0 12.0 2.0 4.5 9.0 12.0 4.5 9.0 12.0 4.5 9.0 12.0 4.5 9.0 12.0 12.0 12.0 12.0 6.0 9.0 12.0 Min 1.50 3.15 6.30 8.40 Max 0.50 1.35 2.70 3.60 220 110 100 150 110 105 ±5.0 ±5.0 ±5.0 20.0 80.0 160.0 Unit V V Ω Ω µA µA µA µA 2020-11-05 Rev.1.0 ©2020 Toshiba Electronic Devices & Storage Corporation
11.6. AC Characteristics (Unless otherwise specified, C L = 50 pF, T a = -40 to 125 , Input: t r = t f = 6 ns) Characteristics Phase difference between input to output Output enable time Output disable time Symbol φI/O tPZL,tPZH tPLZ,tPHZ Test Condition RL = 1 kΩ See 12. AC Test Circuit, Figure 1 RL = 1 kΩ See 12. AC Test Circuit, Figure 1 VCC (V) 2.0 4.5 9.0 12.0 2.0 4.5 9.0 12.0 2.0 4.5 9.0 12.0 Min Max 145 165 Unit ns ns ns 11.7. Analog Switch Characteristics (T a = 25 ) (Note) Characteristics Sine Wave Distortion Maximum frequency response (switch ON) Feed through attenuation (switch OFF) Crosstalk (control input to signal output) Crosstalk (between any switches) Symbol THD fMAX(I/O) FTH Xtalk Xtalk Test Condition RL = 10 kΩ, CL = 50 pF, fIN = 1 kHz VIN is centered at (VCC/2). Adjust input for 0dBm. Increase fIN frequency until dB meter reads -3dB. RL = 50 Ω, CL = 10 pF, fIN = 1 MHz, sine wave See 12. AC Test Circuit, Figure 3 VIN is centered at (VCC/2). Adjust input for 0dBm. RL = 600 Ω, CL = 50 pF, fIN = 1 MHz, sine wave See 12. AC Test Circuit, Figure 4 RL = 600 Ω, CL = 50 pF, fIN = 1 MHz, square wave (tr = tf = 6 ns) See 12. AC Test Circuit, Figure 5 VIN is centered at (VCC/2). Adjust input for 0dBm. RL = 600 Ω, CL = 50 pF, fIN = 1 MHz, sine wave See 12. AC Test Circuit, Figure 6 VIN = 4.5 Vp-p VIN = 9.0 Vp-p VCC (V) 4.5 9.0 4.5 9.0 4.5 9.0 4.5 9.0 4.5 9.0 Typ. 0.05 0.04 200 200 -60 -60 100 -60 -60 Unit MHz dB mV dB Note: These characteristics are determined by design of devices. 2020-11-05 Rev.1.0 ©2020 Toshiba Electronic Devices & Storage Corporation
Unit: mm Weight: 0.054 g (typ.) Package Name(s) Nickname: TSSOP14B 2020-11-05 Rev.1.0 ©2020 Toshiba Electronic Devices & Storage Corporation
https://toshiba.semicon-storage.com/ RESTRICTIONS ON PRODUCT USE Toshiba Corporation and its subsidiaries and affiliates are collectively referred to as "TOSHIBA". Hardware, software and systems described in this document are collectively referred to as "Product".
- TOSHIBA reserves the right to make changes to the information in this document and related Product without notice.
- This document and any information herein may not be reproduced without prior written permission from TOSHIBA. Even with TOSHIBA's written permission, reproduction is permissible only if reproduction is without alteration/omission.
- Though TOSHIBA works continually to improve Product's quality and reliability, Product can malfunction or fail. Customers are responsible for complying with safety standards and for providing adequate designs and safeguards for their hardware, software and systems which minimize risk and avoid situations in which a malfunction or failure of Product could cause loss of human life, bodily injury or damage to property, including data loss or corruption. Before customers use the Product, create designs including the Product, or incorporate the Product into their own applications, customers must also refer to and comply with (a) the latest versions of all relevant TOSHIBA information, including without limitation, this document, the specifications, the data sheets and application notes for Product and the precautions and conditions set forth in the "TOSHIBA Semiconductor Reliability Handbook" and (b) the instructions for the application with which the Product will be used with or for. Customers are solely responsible for all aspects of their own product design or applications, including but not limited to (a) determining the appropriateness of the use of this Product in such design or applications; (b) evaluating and determining the applicability of any information contained in this document, or in charts, diagrams, programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operating parameters for such designs and applications. TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS' PRODUCT DESIGN OR APPLICATIONS.
- PRODUCT IS NEITHER INTENDED NOR WARRANTED FOR USE IN EQUIPMENTS OR SYSTEMS THAT REQUIRE EXTRAORDINARILY HIGH LEVELS OF QUALITY AND/OR RELIABILITY, AND/OR A MALFUNCTION OR FAILURE OF WHICH MAY CAUSE LOSS OF HUMAN LIFE, BODILY INJURY, SERIOUS PROPERTY DAMAGE AND/OR SERIOUS PUBLIC IMPACT ("UNINTENDED USE"). Except for specific applications as expressly stated in this document, Unintended Use includes, without limitation, equipment used in nuclear facilities, equipment used in the aerospace industry, lifesaving and/or life supporting medical equipment, equipment used for automobiles, trains, ships and other transportation, traffic signaling equipment, equipment used to control combustions or explosions, safety devices, elevators and escalators, and devices related to power plant. IF YOU USE PRODUCT FOR UNINTENDED USE, TOSHIBA ASSUMES NO LIABILITY FOR PRODUCT. For details, please contact your TOSHIBA sales representative or contact us via our website.
- Do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy Product, whether in whole or in part.
- Product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable laws or regulations.
- The information contained herein is presented only as guidance for Product use. No responsibility is assumed by TOSHIBA for any infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise.
- ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR LOSS, INCLUDING WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND LOSS OF DATA, AND (2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO SALE, USE OF PRODUCT, OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT.
- Do not use or otherwise make available Product or related software or technology for any military purposes, including without limitation, for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missile technology products (mass destruction weapons). Product and related software and technology may be controlled under the applicable export laws and regulations including, without limitation, the Japanese Foreign Exchange and Foreign Trade Law and the U.S. Export Administration Regulations. Export and re-export of Product or related software or technology are strictly prohibited except in compliance with all applicable export laws and regulations.
- Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product. Please use Product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. TOSHIBA ASSUMES NO LIABILITY FOR DAMAGES OR LOSSES OCCURRING AS A RESULT OF NONCOMPLIANCE WITH APPLICABLE LAWS AND REGULATIONS. 2020-11-05 Rev.1.0 ©2020 Toshiba Electronic Devices & Storage Corporation