74HC4053 PHILIPS
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 33
Technical content
- General description The 74HC4053; 74HCT4053 is a high-speed Si-gate CMOS device and is pin compatible with the HEF4053B. It is specified in compliance with JEDEC standard no. 7A. The 74HC4053; 74HCT4053 is triple 2-channel analog multiplexer/demultiplexer with a common enable input (E). Each multiplexer/demultiplexer has two independent inputs/outputs (nY0 and nY1), a common input/output (nZ) and three digital select inputs (Sn). With E LOW, one of the two switches is selected (low-impedance ON-state) by S1 to S3. WithE HIGH, all switches are in the high-impedance OFF-state, independent of S1 to S3. VCC and GND are the supply voltage pins for the digital control inputs (S1 to S3 andE). The VCC to GND ranges are 2.0 V to 10.0 V for 74HC4053 and 4.5 V to 5.5 V for 74HCT4053. The analog inputs/outputs (nY0 and nY1, and nZ) can swing between VCC as a positive limit and VEE as a negative limit. VCC − VEE may not exceed 10.0 V. For operation as a digital multiplexer/demultiplexer, VEE is connected to GND (typically ground). 2. Features ■ Low ON resistance: ◆ 80 Ω (typical) at VCC − VEE = 4.5 V ◆ 70 Ω (typical) at VCC − VEE = 6.0 V ◆ 60 Ω (typical) at VCC − VEE = 9.0 V ■ Logic level translation: ◆ To enable 5 V logic to communicate with±5 V analog signals ■ Typical ‘break before make’ built in ■ Complies with JEDEC standard no. 7A ■ ESD protection: ◆ HBM EIA/JESD22-A114-C exceeds 2000 V ◆ MM EIA/JESD22-A115-A exceeds 200 V ■ Multiple package options ■ Specified from−40 °Ct o+ 8 5°C and from−40 °C to +125°C 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer Rev. 04 — 9 May 2006 Product data sheet
74HC_HCT4053_4 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 — 9 May 2006 2 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer 3. Applications ■ Analog multiplexing and demultiplexing ■ Digital multiplexing and demultiplexing ■ Signal gating 4. Quick reference data [1] C PD is used to determine the dynamic power dissipation (PD inµW). PD =C PD × VCC 2 × fi +∑ {(CL + CS)× VCC 2 × fo} where: fi= input frequency in MHz; fo = output frequency in MHz; ∑ {(CL + CS)× VCC 2 × fo} = sum of outputs; Table 1: Quick reference data VEE = GND = 0 V; Tamb =2 5°C; tr =tf= 6 ns. Symbol Parameter Conditions Min Typ Max Unit 74HC4053 t PZH , tPZL turn-ON time C L = 15 pF; RL =1k Ω ; VCC =5 V E to Vos -1 7 -n s Sn to Vos -2 1 -n s tPHZ , tPLZ turn-OFF time C L = 15 pF; RL =1k Ω ; VCC =5 V E to Vos -1 8 -n s Sn to Vos -1 7 -n s C i input capacitance - 3.5 - pF C S switch capacitance independent I/O (nYn) - 5 - pF common I/O (nZ) - 8 - pF C PD power dissipation capacitance per switch; VI= GND to VCC [1] -3 6 -p F 74HCT4053 tPZH , tPZL turn-ON time C L = 15 pF; RL =1k Ω ; VCC =5 V E to Vos -2 3 -n s Sn to Vos -2 1 -n s tPHZ , tPLZ turn-OFF time C L = 15 pF; RL =1k Ω ; VCC =5 V E to Vos -2 0 -n s Sn to Vos -1 9 -n s C i input capacitance - 3.5 - pF C S switch capacitance independent I/O (nYn) - 5 - pF common I/O(nZ) - 8 - pF C PD power dissipation capacitance per switch; VI= GND to (VCC − 1.5 V) [1] -3 6 -p F
74HC_HCT4053_4 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 — 9 May 2006 3 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer C L = output load capacitance in pF; C S = maximum switch capacitance in pF; VCC = supply voltage in V. 5. Ordering information Table 2: Ordering information Type number Package Temperature range Name Description Version 74HC4053 74HC4053N −40 °C to +125°C DIP16 plastic dual in-line package; 16 leads (300 mil); long body SOT38-4 74HC4053D −40 °C to +125°C SO16 plastic small outline package; 16 leads; body width 3.9 mm SOT109-1 74HC4053DB −40 °C to +125°C SSOP16 plastic shrink small outline package; 16 leads; body width 5.3 mm SOT338-1 74HC4053PW −40 °C to +125°C TSSOP16 plastic thin shrink small outline package; 16 leads; body width 4.4 mm SOT403-1 74HC4053BQ −40 °C to +125°C DHVQFN16 plastic dual in-line compatible thermal enhanced very thin quad flat package; no leads; 16 terminals; body 2.5× 3.5× 0.85 mm SOT763-1 74HCT4053 74HCT4053N −40 °C to +125°C DIP16 plastic dual in-line package; 16 leads (300 mil); long body SOT38-4 74HCT4053D −40 °C to +125°C SO16 plastic small outline package; 16 leads; body width 3.9 mm SOT109-1 74HCT4053DB −40 °C to +125°C SSOP16 plastic shrink small outline package; 16 leads; body width 5.3 mm SOT338-1 74HCT4053PW −40 °C to +125°C TSSOP16 plastic thin shrink small outline package; 16 leads; body width 4.4 mm SOT403-1 74HCT4053BQ −40 °C to +125°C DHVQFN16 plastic dual in-line compatible thermal enhanced very thin quad flat package; no leads; 16 terminals; body 2.5× 3.5× 0.85 mm SOT763-1
74HC_HCT4053_4 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 — 9 May 2006 4 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer 6. Functional diagram Fig 1. Functional diagram Fig 2. Logic symbol Fig 3. IEC logic symbol 001aae124 LOGIC LEVEL CONVERSION VCC 13 1Y1 S1 DECODER 12 1Y0 14 1Z 1 2Y1 2 2Y0 15 2Z 3 3Y1 5 3Y0 43 Z 10S2 GND V EE E 001aae125 1Y0 12 1Y1 S210 S39 6 E 2Y0 2 2Y1 1 3Y0 5 3Y1 3 3Z 4 2Z 15 1Z 14 001aae126 6 EN 11 # MUX/DMUX
- 0 114 10 2 115 9 5
74HC_HCT4053_4 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 — 9 May 2006 5 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer 7. Pinning information
7.1 Pinning
Fig 4. Schematic diagram (one switch) 001aad544 from logic VCC VEE VEE VCC VCC VEE Y Z VCC (1) The die substrate is attached to this pad using conductive die attach material. It can not be used as supply pin or input. Fig 5. Pin configuration DIP16, SO16 and (T)SSOP16 Fig 6. Pin configuration DHVQFN16 74HC4053 74HCT4053 2Y1 V CC 2Y0 2Z 3Y1 1Z 3Z 1Y1 3Y0 1Y0 ES 1 VEE S2 GND S3 001aae127 001aae128 VEE S2 ES 1 3Y0 1Y0 3Z 1Y1 3Y1 1Z 2Y0 2Z GND 2Y1 VCC Transparent top view 7 10 6 11 5 12 4 13 3 14 2 15 terminal 1 index area GND (1) 74HC4053 74HCT4053
74HC_HCT4053_4 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 — 9 May 2006 6 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer
7.2 Pin description
- Functional description
8.1 Function table
[1] H = HIGH voltage level; L = LOW voltage level; X = don’t care. 9. Limiting values Table 3: Pin description Symbol Pin Description 2Y1 1 2 independent input/output 1 2Y0 2 2 independent input/output 0 3Y1 3 3 independent input/output 1 3Z 4 3 common input/output 3Y0 5 3 independent input/output 0 E 6 enable input (active LOW) V EE 7 negative supply voltage GND 8 ground (0 V) S3 9 select input 3 S2 10 select input 2 S1 11 select input 1 1Y0 12 1 independent input/output 0 1Y1 13 1 independent input/output 1 1Z 14 1 common input/output 2Z 15 2 common input/output V CC 16 supply voltage Table 4: Function table[1] Control Channel on E Sn L L nY0 to nZ H nY1 to nZ H X none Table 5: Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to VEE = GND (ground = 0 V).[1] Symbol Parameter Conditions Min Max Unit VCC supply voltage −0.5 +11.0 V IIK input clamping current VI< −0.5 V or VI>V CC + 0.5 V - ±20 mA ISK switch clamping current VS < −0.5 V or VS >V CC + 0.5 V - ±20 mA
74HC_HCT4053_4 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 — 9 May 2006 7 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer [1] To avoid drawing VCC current out of terminals nZ, when switch current flows in terminals nYn, the voltage drop across the bidirectional switch must not exceed 0.4 V. If the switch current flows into terminals nZ, no V CC current will flow out of terminals nYn. In this case there is no limit for the voltage drop across the switch, but the voltages at nYn and nZ may not exceed VCC or VEE . [2] For DIP16 package: Ptot derates linearly with 12 mW/K above 70°C. [3] For SO16 package: Ptot derates linearly with 8 mW/K above 70°C. [4] For SSOP16 and TSSOP16 packages: Ptot derates linearly with 5.5 mW/K above 60°C. [5] For DHVQFN16 packages: Ptot derates linearly with 4.5 mW/K above 60°C. 10. Recommended operating conditions IS switch current −0.5 V < VS <V CC + 0.5 V - ±25 mA IEE negative supply current - −20 mA ICC quiescent supply current - 50 mA IGND ground current - −50 mA Tstg storage temperature −65 +150 °C Ptot total power dissipation Tamb = −40 °C to + 125°C DIP16 package [2] - 750 mW SO16 package [3] - 500 mW SSOP16 package [4] - 500 mW TSSOP16 package [4] - 500 mW DHVQFN16 package [5] - 500 mW PS power dissipation per switch - 100 mW Table 5: Limiting values …continued In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to VEE = GND (ground = 0 V).[1] Symbol Parameter Conditions Min Max Unit Table 6: Recommended operating conditions Symbol Parameter Conditions Min Typ Max Unit 74HC4053 ΔV CC supply voltage difference seeFigure7 VCC − GND 2.0 5.0 10.0 V VCC − VEE 2.0 5.0 10.0 V VI input voltage GND - V CC V VS switch voltage V EE -V CC V Tamb ambient temperature −40 +25 +125 °C tr, tf input rise and fall times VCC = 2.0 V - 6.0 1000 ns VCC = 4.5 V - 6.0 500 ns VCC = 6.0 V - 6.0 400 ns VCC = 10.0 V - 6.0 250 ns 74HCT4053 ΔV CC supply voltage difference seeFigure7 VCC − GND 4.5 5.0 5.5 V VCC − VEE 2.0 5.0 10.0 V
74HC_HCT4053_4 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 — 9 May 2006 8 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer 11. Static characteristics VI input voltage GND - V CC V VS switch voltage V EE -V CC V Tamb ambient temperature −40 +25 +125 °C tr, tf input rise and fall times VCC = 4.5 V - 6.0 500 ns Table 6: Recommended operating conditions …continued Symbol Parameter Conditions Min Typ Max Unit a. Type 74HC4053 b. Type 74HCT4053 Fig 7. Guaranteed operating area as a function of the supply voltages VCC − VEE (V) 01 0 8462 001aad545 operating area VCC − GND (V) VCC − VEE (V) 01 0 8462 001aad546 VCC − GND (V) operating area Table 7: R ON resistance per switch 74HC4053 and 74HCT4053 For test circuit seeFigure8. Vis is the input voltage at a nYn or nZ terminal, whichever is assigned as an input. Vos is the output voltage at a nYn or nZ terminal, whichever is assigned as an output. Symbol Parameter Conditions Min Typ Max Unit Tamb = 25°C R ON(peak) ON resistance (peak) Vis = VCC to VEE ; VI = VIH or VIL VCC = 2.0 V; VEE = 0 V; IS = 100µA [1] --- Ω VCC = 4.5 V; VEE = 0 V; IS = 1000µA - 100 180 Ω VCC = 6.0 V; VEE = 0 V; IS = 1000µA - 90 160 Ω VCC = 4.5 V; VEE =−4.5 V; IS = 1000µA - 70 130 Ω
74HC_HCT4053_4 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 — 9 May 2006 9 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer R ON(rail) ON resistance (rail) Vis = VEE ; VI = VIH or VIL VCC = 2.0 V; VEE = 0 V; IS = 100µA [1] - 150 - Ω VCC = 4.5 V; VEE = 0 V; IS = 1000µA - 80 140 Ω VCC = 6.0 V; VEE = 0 V; IS = 1000µA - 70 120 Ω VCC = 4.5 V; VEE =−4.5 V; IS = 1000µA - 60 105 Ω Vis = VCC ; VI = VIH or VIL VCC = 2.0 V; VEE = 0 V; IS = 100µA [1] - 150 - Ω VCC = 4.5 V; VEE = 0 V; IS = 1000µA - 90 160 Ω VCC = 6.0 V; VEE = 0 V; IS = 1000µA - 80 140 Ω VCC = 4.5 V; VEE =−4.5 V; IS = 1000µA - 65 120 Ω ΔR ON ON resistance mismatch between channels V is = VCC to VEE ; VI = VIH or VIL VCC = 2.0 V; VEE = 0 V [1] --- Ω VCC = 4.5 V; VEE = 0 V - 9 - Ω VCC = 6.0 V; VEE = 0 V - 8 - Ω VCC = 4.5 V; VEE =−4.5 V - 6 - Ω Tamb =−40 °C to +85°C R ON(peak) ON resistance (peak) Vis = VCC to VEE ; VI = VIH or VIL VCC = 2.0 V; VEE = 0 V; IS = 100µA [1] --- Ω VCC = 4.5 V; VEE = 0 V; IS = 1000µA - - 225 Ω VCC = 6.0 V; VEE = 0 V; IS = 1000µA - - 200 Ω VCC = 4.5 V; VEE =−4.5 V; IS = 1000µA - - 165 Ω R ON(rail) ON resistance (rail) Vis = VEE ; VI = VIH or VIL VCC = 2.0 V; VEE = 0 V; IS = 100µA [1] --- Ω VCC = 4.5 V; VEE = 0 V; IS = 1000µA - - 175 Ω VCC = 6.0 V; VEE = 0 V; IS = 1000µA - - 150 Ω VCC = 4.5 V; VEE =−4.5 V; IS = 1000µA - - 130 Ω Vis = VCC ; VI = VIH or VIL VCC = 2.0 V; VEE = 0 V; IS = 100µA [1] --- Ω VCC = 4.5 V; VEE = 0 V; IS = 1000µA - - 200 Ω VCC = 6.0 V; VEE = 0 V; IS= 1000µA - - 175 Ω VCC = 4.5 V; VEE =−4.5 V; IS = 1000µA - - 150 Ω Tamb =−40 °C to +125°C R ON(peak) ON resistance (peak) Vis = VCC to VEE ; VI = VIH or VIL VCC = 2.0 V; VEE = 0 V; IS = 100µA [1] --- Ω VCC = 4.5 V; VEE = 0 V; IS = 1000µA - - 270 Ω VCC = 6.0 V; VEE = 0 V; IS = 1000µA - - 240 Ω VCC = 4.5 V; VEE =−4.5 V; IS = 1000µA - - 195 Ω Table 7: R ON resistance per switch 74HC4053 and 74HCT4053 …continued For test circuit seeFigure8. Vis is the input voltage at a nYn or nZ terminal, whichever is assigned as an input. Vos is the output voltage at a nYn or nZ terminal, whichever is assigned as an output. Symbol Parameter Conditions Min Typ Max Unit
74HC_HCT4053_4 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 — 9 May 2006 10 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer [1] At supply voltages (VCC − VEE ) approaching 2.0 V the analog switch ON resistance becomes extremely non-linear. Therefore, it is recommended that these devices be used to transmit digital signals only, when using these supply voltages. R ON(rail) ON resistance (rail) Vis = VEE ; VI = VIH or VIL VCC = 2.0 V; VEE = 0 V; IS = 100µA [1] --- Ω VCC = 4.5 V; VEE = 0 V; IS = 1000µA - - 210 Ω VCC = 6.0 V; VEE = 0 V; IS = 1000µA - - 180 Ω VCC = 4.5 V; VEE =−4.5 V; IS = 1000µA - - 160 Ω Vis = VCC ; VI = VIH or VIL VCC = 2.0 V; VEE = 0 V; IS = 100µA [1] --- Ω VCC = 4.5 V; VEE = 0 V; IS = 1000µA - - 240 Ω VCC = 6.0 V; VEE = 0 V; IS = 1000µA - - 210 Ω VCC = 4.5 V; VEE =−4.5 V; IS = 1000µA - - 180 Ω Table 7: R ON resistance per switch 74HC4053 and 74HCT4053 …continued For test circuit seeFigure8. Vis is the input voltage at a nYn or nZ terminal, whichever is assigned as an input. Vos is the output voltage at a nYn or nZ terminal, whichever is assigned as an output. Symbol Parameter Conditions Min Typ Max Unit R ON =V S / IS.V is=0Vt o( VCC − VEE ). (1) VCC = 4.5 V (2) VCC =6V (3) VCC =9V Fig 8. Test circuit for measuring RON Fig 9. Typical RON as a function of input voltage Vis 001aae129 VS nYn nZ ISVis = 0 V to (VCC - VEE ) HIGH (from select input) VEE Vis (V) mnb047 110 R ON (Ω ) (1) (2) (3)
74HC_HCT4053_4 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 — 9 May 2006 11 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer Table 8: Static characteristics 74HC4053 At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Vis is the input voltage at a nYn or nZ terminal, whichever is assigned as an input. Vos is the output voltage at a nYn or nZ terminal, whichever is assigned as an output. Symbol Parameter Conditions Min Typ Max Unit Tamb = 25°C VIH HIGH-state input voltage VCC = 2.0 V 1.5 1.2 - V VCC = 4.5 V 3.15 2.4 - V VCC = 6.0 V 4.2 3.2 - V VCC = 9.0 V 6.3 4.7 - V VIL LOW-state input voltage VCC = 2.0 V - 0.8 0.5 V VCC = 4.5 V - 2.1 1.35 V VCC = 6.0 V - 2.8 1.8 V VCC = 9.0 V - 4.3 2.7 V ILI input leakage current VI = VCC or GND; VEE = 0 V VCC = 6.0 V - - ±0.1 µA VCC = 10.0 V - - ±0.2 µA IS(OFF) OFF-state leakage current VCC = 10.0 V; VI = VIH or VIL; VEE =0V ; |VS| = VCC − VEE ; seeFigure10 per channel - - ±0.1 µA all channels - - ±0.1 µA IS(ON) ON-state leakage current VCC = 10.0 V; VI = VIH or VIL; VEE =0V ; |VS| = VCC − VEE ; seeFigure11 -- ±0.1 µA ICC quiescent supply current Vis = VEE or VCC ; Vos = VCC or VEE ; VI=V CC or GND; VEE = 0 V VCC = 6.0 V - - 8.0 µA VCC = 10.0 V - - 16.0 µA C i input capacitance - 3.5 - pF C S switch capacitance independent I/O (nYn) - 5 - pF common I/O (nZ) - 8 - pF T amb =−40 °C to +85°C VIH HIGH-state input voltage VCC = 2.0 V 1.5 - - V VCC = 4.5 V 3.15 - - V VCC = 6.0 V 4.2 - - V VCC = 9.0 V 6.3 - - V VIL LOW-state input voltage VCC = 2.0 V - - 0.5 V VCC = 4.5 V - - 1.35 V VCC = 6.0 V - - 1.8 V VCC = 9.0 V - - 2.7 V ILI input leakage current VI = VCC or GND; VEE = 0 V VCC = 6.0 V - - ±1.0 µA VCC = 10.0 V - - ±2.0 µA
74HC_HCT4053_4 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 — 9 May 2006 12 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer IS(OFF) OFF-state leakage current VCC = 10.0 V; VI = VIH or VIL; VEE =0V ; |VS| = VCC − VEE ; seeFigure10 per channel - - ±1.0 µA all channels - - ±1.0 µA IS(ON) ON-state leakage current VCC = 10.0 V; VI = VIH or VIL; VEE =0V ; |VS| = VCC − VEE ; seeFigure11 -- ±1.0 µA ICC quiescent supply current Vis = VEE or VCC ; Vos = VCC or VEE ; VI=V CC or GND; VEE = 0 V VCC = 6.0 V - - 80.0 µA VCC = 10.0 V - - 160.0 µA Tamb =−40 °C to +125°C VIH HIGH-state input voltage VCC = 2.0 V 1.5 - - V VCC = 4.5 V 3.15 - - V VCC = 6.0 V 4.2 - - V VCC = 9.0 V 6.3 - - V VIL LOW-state input voltage VCC = 2.0 V - - 0.5 V VCC = 4.5 V - - 1.35 V VCC = 6.0 V - - 1.8 V VCC = 9.0 V - - 2.7 V ILI input leakage current VI = VCC or GND; VEE = 0 V VCC = 6.0 V - - ±1.0 µA VCC = 10.0 V - - ±2.0 µA IS(OFF) OFF-state leakage current VCC = 10.0 V; VI = VIH or VIL; VEE =0V ; |VS| = VCC − VEE ; seeFigure10 per channel - - ±1.0 µA all channels - - ±1.0 µA IS(ON) ON-state leakage current VCC = 10.0 V; VI = VIH or VIL; VEE =0V ; |VS| = VCC − VEE ; seeFigure11 -- ±1.0 µA ICC quiescent supply current Vis = VEE or VCC ; Vos = VCC or VEE ; VI=V CC or GND; VEE = 0 V VCC = 6.0 V - - 160.0 µA VCC = 10.0 V - - 320.0 µA Table 8: Static characteristics 74HC4053 …continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Vis is the input voltage at a nYn or nZ terminal, whichever is assigned as an input. Vos is the output voltage at a nYn or nZ terminal, whichever is assigned as an output. Symbol Parameter Conditions Min Typ Max Unit Table 9: Static characteristics 74HCT4053 Voltages are referenced to GND (ground=0V ) . Vis is the input voltage at a nYn or nZ terminal, whichever is assigned as an input. Vos is the output voltage at a nYn or nZ terminal, whichever is assigned as an output. Symbol Parameter Conditions Min Typ Max Unit Tamb = 25°C VIH HIGH-state input voltage VCC = 4.5 V to 5.5 V 2.0 1.6 - µA VIL LOW-state input voltage VCC = 4.5 V to 5.5 V - 1.2 0.8 µA
74HC_HCT4053_4 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 — 9 May 2006 13 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer ILI input leakage current VCC = 5.5 V; VEE = 0 V; VI = VCC or GND - - ±0.1 µA IS(OFF) OFF-state leakage current VCC = 10.0 V; VI = VIH or VIL; VEE =0V ; |VS| = VCC − VEE ; seeFigure10 per channel - - ±0.1 µA all channels - - ±0.1 µA IS(ON) ON-state leakage current VCC = 10.0 V; VI = VIH or VIL; VEE =0V ; |VS| = VCC − VEE ; seeFigure11 -- ±0.1 µA ICC quiescent supply current VI = VCC or GND; Vis = VEE or VCC ; Vos =V CC or VEE VCC = 5.5 V; VEE = 0 V - - 8.0 µA VCC = 5.0 V; VEE =−5.0 V - - 16.0 µA ΔICC additional quiescent supply current per input pin; VCC = 4.5 V to 5.5 V; VEE = 0 V; VI = VCC − 2.1 V; other inputs at VCC or GND - 50 180 µA C i input capacitance - 3.5 - pF C S switch capacitance independent I/O (nYn) - 5 - pF common I/O (nZ) - 8 - pF T amb =−40 °C to +85°C VIH HIGH-state input voltage VCC = 4.5 V to 5.5 V 2.0 - - µA VIL LOW-state input voltage VCC = 4.5 V to 5.5 V - - 0.8 µA ILI input leakage current VCC = 5.5 V; VEE = 0 V; VI = VCC or GND - - ±1.0 µA IS(OFF) OFF-state leakage current VCC = 10.0 V; VI = VIH or VIL; VEE =0V ; |VS| = VCC − VEE ; seeFigure10 per channel - - ±1.0 µA all channels - - ±1.0 µA IS(ON) ON-state leakage current VCC = 10.0 V; VI = VIH or VIL; VEE =0V ; |VS| = VCC − VEE ; seeFigure11 -- ±1.0 µA ICC quiescent supply current VI = VCC or GND; Vis = VEE or VCC ; Vos =V CC or VEE VCC = 5.5 V; VEE = 0 V - - 80.0 µA VCC = 5.0 V; VEE =−5.0 V - - 160.0 µA ΔICC additional quiescent supply current per input pin; VCC = 4.5 V to 5.5 V; VEE = 0 V; VI = VCC − 2.1 V; other inputs at VCC or GND - - 225 µA Tamb =−40 °C to +125°C VIH HIGH-state input voltage VCC = 4.5 V to 5.5 V 2.0 - - µA VIL LOW-state input voltage VCC = 4.5 V to 5.5 V - - 0.8 µA ILI input leakage current VCC = 5.5 V; VEE = 0 V; VI = VCC or GND - - ±1.0 µA Table 9: Static characteristics 74HCT4053 …continued Voltages are referenced to GND (ground=0V ) . Vis is the input voltage at a nYn or nZ terminal, whichever is assigned as an input. Vos is the output voltage at a nYn or nZ terminal, whichever is assigned as an output. Symbol Parameter Conditions Min Typ Max Unit
74HC_HCT4053_4 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 — 9 May 2006 14 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer 12. Dynamic characteristics IS(OFF) OFF-state leakage current VCC = 10.0 V; VI = VIH or VIL; VEE =0V ; |VS| = VCC − VEE ; seeFigure10 per channel - - ±1.0 µA all channels - - ±1.0 µA IS(ON) ON-state leakage current VCC = 10.0 V; VI = VIH or VIL; VEE =0V ; |VS| = VCC − VEE ; seeFigure11 -- ±1.0 µA ICC quiescent supply current VI = VCC or GND; Vis = VEE or VCC ; Vos =V CC or VEE VCC = 5.5 V; VEE = 0 V - - 160.0 µA VCC = 5.0 V; VEE =−5.0 V - - 320.0 µA ΔICC additional quiescent supply current per input pin; VCC = 4.5 V to 5.5 V; VEE = 0 V; VI = VCC − 2.1 V; other inputs at VCC or GND - - 245 µA Table 9: Static characteristics 74HCT4053 …continued Voltages are referenced to GND (ground=0V ) . Vis is the input voltage at a nYn or nZ terminal, whichever is assigned as an input. Vos is the output voltage at a nYn or nZ terminal, whichever is assigned as an output. Symbol Parameter Conditions Min Typ Max Unit Fig 10. Test circuit for measuring OFF-state leakage current Fig 11. Test circuit for measuring ON-state leakage current 001aae130 AA nYn Sn nZ VI = VCC or VEE VO = VEE or VCC LOW (select input) VEE 001aae131 A VI = VEE or VCC VO (open circuit) HIGH (select input) VEE nYn Sn nZ Table 10: Dynamic characteristics type 74HC4053 Voltages are referenced to GND (ground = 0 V); tr =tf= 6 ns; CL = 50 pF unless otherwise specified; for test circuit see Figure14. Vis is the input voltage at a nYn or nZ terminal, whichever is assigned as an input. Vos is the output voltage at a nYn or nZ terminal, whichever is assigned as an output. Symbol Parameter Conditions Min Typ Max Unit Tamb = 25°C tPHL , tPLH propagation delay Vis to Vos R L =∞Ω ; seeFigure12 VCC = 2.0 V; VEE = 0 V - 1 56 0n s VCC = 4.5 V; VEE = 0 V - 5 12 ns VCC = 6.0 V; VEE = 0 V - 4 10 ns VCC = 4.5 V; VEE =−4.5 V - 4 8 ns
74HC_HCT4053_4 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 — 9 May 2006 15 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer tPZH , tPZL turn-ON time R L = 1 kΩ ; seeFigure13 E to Vos VCC = 2.0 V; VEE = 0 V - 60 220 ns VCC = 4.5 V; VEE = 0 V - 2 04 4n s VCC = 6.0 V; VEE = 0 V - 1 63 7n s VCC = 4.5 V; VEE =−4.5 V - 15 31 ns VCC = 5 V; VEE =0V ; CL =1 5p F - 1 7 - n s Sn to Vos VCC = 2.0 V; VEE = 0 V - 75 220 ns VCC = 4.5 V; VEE = 0 V - 2 54 4n s VCC = 6.0 V; VEE = 0 V - 2 03 7n s VCC = 4.5 V; VEE =−4.5 V - 15 31 ns VCC = 5 V; VEE =0V ; CL =1 5p F - 2 1 - n s tPHZ , tPLZ turn-OFF time R L = 1 kΩ ; seeFigure13 E to Vos VCC = 2.0 V; VEE = 0 V - 63 210 ns VCC = 4.5 V; VEE = 0 V - 2 14 2n s VCC = 6.0 V; VEE = 0 V - 1 73 6n s VCC = 4.5 V; VEE =−4.5 V - 15 29 ns VCC = 5 V; CL =1 5p F - 1 8 - n s Sn to Vos VCC = 2.0 V; VEE = 0 V - 60 210 ns VCC = 4.5 V; VEE = 0 V - 2 04 2n s VCC = 6.0 V; VEE = 0 V - 1 63 6n s VCC = 4.5 V; VEE =−4.5 V - 15 29 ns VCC = 5 V; CL =1 5p F - 1 7 - n s C PD power dissipation capacitance per switch; VI= GND to VCC [1] -3 6 -p F Tamb =−40 °C to +85°C tPHL , tPLH propagation delay Vis to Vos R L =∞Ω ; seeFigure12 VCC = 2.0 V; VEE = 0 V - - 75 ns VCC = 4.5 V; VEE = 0 V - - 15 ns VCC = 6.0 V; VEE = 0 V - - 13 ns VCC = 4.5 V; VEE =−4.5 V - - 10 ns Table 10: Dynamic characteristics type 74HC4053 …continued Voltages are referenced to GND (ground = 0 V); tr =tf= 6 ns; CL = 50 pF unless otherwise specified; for test circuit see Figure14. Vis is the input voltage at a nYn or nZ terminal, whichever is assigned as an input. Vos is the output voltage at a nYn or nZ terminal, whichever is assigned as an output. Symbol Parameter Conditions Min Typ Max Unit
74HC_HCT4053_4 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 — 9 May 2006 16 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer tPZH , tPZL turn-ON time R L = 1 kΩ ; seeFigure13 E to Vos VCC = 2.0 V; VEE = 0 V - - 275 ns VCC = 4.5 V; VEE = 0 V - - 55 ns VCC = 6.0 V; VEE = 0 V - - 47 ns VCC = 4.5 V; VEE =−4.5 V - - 39 ns Sn to Vos VCC = 2.0 V; VEE = 0 V - - 275 ns VCC = 4.5 V; VEE = 0 V - - 55 ns VCC = 6.0 V; VEE = 0 V - - 47 ns VCC = 4.5 V; VEE =−4.5 V - - 39 ns tPHZ , tPLZ turn-OFF time R L = 1 kΩ ; seeFigure13 E to Vos VCC = 2.0 V; VEE = 0 V - - 265 ns VCC = 4.5 V; VEE = 0 V - - 53 ns VCC = 6.0 V; VEE = 0 V - - 45 ns VCC = 4.5 V; VEE =−4.5 V - - 36 ns Sn to Vos VCC = 2.0 V; VEE = 0 V - - 265 ns VCC = 4.5 V; VEE = 0 V - - 53 ns VCC = 6.0 V; VEE = 0 V - - 45 ns VCC = 4.5 V; VEE =−4.5 V - - 36 ns Tamb =−40 °C to +125°C tPHL , tPLH propagation delay Vis to Vos R L =∞Ω ; seeFigure12 VCC = 2.0 V; VEE = 0 V - - 90 ns VCC = 4.5 V; VEE = 0 V - - 18 ns VCC = 6.0 V; VEE = 0 V - - 15 ns VCC = 4.5 V; VEE =−4.5 V - - 12 ns tPZH , tPZL turn-ON time R L = 1 kΩ ; seeFigure13 E to Vos VCC = 2.0 V; VEE = 0 V - - 330 ns VCC = 4.5 V; VEE = 0 V - - 66 ns VCC = 6.0 V; VEE = 0 V - - 56 ns VCC = 4.5 V; VEE =−4.5 V - - 47 ns Sn to Vos VCC = 2.0 V; VEE = 0 V - - 330 ns VCC = 4.5 V; VEE = 0 V - - 66 ns VCC = 6.0 V; VEE = 0 V - - 56 ns VCC = 4.5 V; VEE =−4.5 V - - 47 ns Table 10: Dynamic characteristics type 74HC4053 …continued Voltages are referenced to GND (ground = 0 V); tr =tf= 6 ns; CL = 50 pF unless otherwise specified; for test circuit see Figure14. Vis is the input voltage at a nYn or nZ terminal, whichever is assigned as an input. Vos is the output voltage at a nYn or nZ terminal, whichever is assigned as an output. Symbol Parameter Conditions Min Typ Max Unit
74HC_HCT4053_4 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 — 9 May 2006 17 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer [1] C PD is used to determine the dynamic power dissipation (PD inµW): PD =C PD × VCC 2 × fi +∑ {(CL + CS)× VCC 2 × fo} where: fi= input frequency in MHz; fo = output frequency in MHz; ∑ {(CL + CS)× VCC 2 × fo} = sum of outputs; C L = output load capacitance in pF; C S = maximum switch capacitance in pF; VCC = supply voltage in V. tPHZ , tPLZ turn-OFF time R L = 1 kΩ ; seeFigure13 E to Vos VCC = 2.0 V; VEE = 0 V - - 315 ns VCC = 4.5 V; VEE = 0 V - - 63 ns VCC = 6.0 V; VEE = 0 V - - 54 ns VCC = 4.5 V; VEE =−4.5 V - - 44 ns Sn to Vos VCC = 2.0 V; VEE = 0 V - - 315 ns VCC = 4.5 V; VEE = 0 V - - 63 ns VCC = 6.0 V; VEE = 0 V - - 54 ns VCC = 4.5 V; VEE =−4.5 V - - 44 ns Table 10: Dynamic characteristics type 74HC4053 …continued Voltages are referenced to GND (ground = 0 V); tr =tf= 6 ns; CL = 50 pF unless otherwise specified; for test circuit see Figure14. Vis is the input voltage at a nYn or nZ terminal, whichever is assigned as an input. Vos is the output voltage at a nYn or nZ terminal, whichever is assigned as an output. Symbol Parameter Conditions Min Typ Max Unit Table 11: Dynamic characteristics type 74HCT4053 Voltages are referenced to GND (ground = 0 V); tr =tf= 6 ns; CL = 50 pF unless otherwise specified; for test circuit see Figure14. Vis is the input voltage at a nYn or nZ terminal, whichever is assigned as an input. Vos is the output voltage at a nYn or nZ terminal, whichever is assigned as an output. Symbol Parameter Conditions Min Typ Max Unit Tamb = 25°C tPHL , tPLH propagation delay Vis to Vos VCC = 4.5 V; RL =∞Ω ; seeFigure12 VEE = 0 V - 5 12 ns VEE =−4.5 V - 4 8 ns tPZH , tPZL turn-ON time R L = 1 kΩ ; seeFigure13 E to Vos VCC = 4.5 V; VEE = 0 V - 2 74 8n s VCC = 4.5 V; VEE =−4.5 V - 16 34 ns VCC = 5 V; VEE =0V ; CL =1 5p F - 2 3 - n s Sn to Vos VCC = 4.5 V; VEE = 0 V - 2 54 8n s VCC = 4.5 V; VEE =−4.5 V - 16 34 ns VCC = 5 V; VEE =0V ; CL =1 5p F - 2 1 - n s
74HC_HCT4053_4 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 — 9 May 2006 18 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer tPHZ , tPLZ turn-OFF time R L = 1 kΩ ; seeFigure13 E to Vos VCC = 4.5 V; VEE = 0 V - 2 44 4n s VCC = 4.5 V; VEE =−4.5 V - 15 31 ns VCC = 5 V; VEE =0V ; CL =1 5p F - 2 0 - n s Sn to Vos VCC = 4.5 V; VEE = 0 V - 2 24 4n s VCC = 4.5 V; VEE =−4.5 V - 15 31 ns VCC = 5 V; VEE =0V ; CL =1 5p F - 1 9 - n s C PD power dissipation capacitance per switch; VI= GND to (VCC − 1.5 V) [1] -3 6 -p F Tamb =−40 °C to +85°C tPHL , tPLH propagation delay Vis to Vos VCC = 4.5 V; RL =∞Ω ; seeFigure12 VEE = 0 V - - 15 ns VEE =−4.5 V - - 10 ns tPZH , tPZL turn-ON time V CC = 4.5 V; RL =1k Ω ; seeFigure13 E to Vos VEE = 0 V - - 60 ns VEE =−4.5 V - - 43 ns Sn to Vos VEE = 0 V - - 60 ns VEE =−4.5 V - - 43 ns tPHZ , tPLZ turn-OFF time V CC = 4.5 V; RL =1k Ω ; seeFigure13 E to Vos VEE = 0 V - - 55 ns VEE =−4.5 V - - 39 ns Sn to Vos VEE = 0 V - - 55 ns VEE =−4.5 V - - 39 ns Tamb =−40 °C to +125°C tPHL , tPLH propagation delay Vis to Vos VCC = 4.5 V; RL =∞Ω ; seeFigure12 VEE = 0 V - - 18 ns VEE =−4.5 V - - 12 ns tPZH , tPZL turn-ON time V CC = 4.5 V; RL =1k Ω ; seeFigure13 E to Vos VEE = 0 V - - 72 ns VEE =−4.5 V - - 51 ns Sn to Vos VEE = 0 V - - 72 ns VEE =−4.5 V - - 51 ns Table 11: Dynamic characteristics type 74HCT4053 …continued Voltages are referenced to GND (ground = 0 V); tr =tf= 6 ns; CL = 50 pF unless otherwise specified; for test circuit see Figure14. Vis is the input voltage at a nYn or nZ terminal, whichever is assigned as an input. Vos is the output voltage at a nYn or nZ terminal, whichever is assigned as an output. Symbol Parameter Conditions Min Typ Max Unit
74HC_HCT4053_4 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 — 9 May 2006 19 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer [1] C PD is used to determine the dynamic power dissipation (PD inµW): PD =C PD × VCC 2 × fi +∑ {(CL + CS)× VCC 2 × fo} where: fi= input frequency in MHz; fo = output frequency in MHz; ∑ {(CL + CS)× VCC 2 × fo} = sum of outputs; C L = output load capacitance in pF; C S = maximum switch capacitance in pF; VCC = supply voltage in V. 13. Waveforms tPHZ , tPLZ turn-OFF time V CC = 4.5 V; RL =1k Ω ; seeFigure13 E to Vos VEE = 0 V - - 66 ns VEE =−4.5 V - - 47 ns Sn to Vos VEE = 0 V - - 66 ns VEE =−4.5 V - - 47 ns Table 11: Dynamic characteristics type 74HCT4053 …continued Voltages are referenced to GND (ground = 0 V); tr =tf= 6 ns; CL = 50 pF unless otherwise specified; for test circuit see Figure14. Vis is the input voltage at a nYn or nZ terminal, whichever is assigned as an input. Vos is the output voltage at a nYn or nZ terminal, whichever is assigned as an output. Symbol Parameter Conditions Min Typ Max Unit Fig 12. Propagation delay input (Vis) to output (Vos) 001aad555 tPLH tPHL 50 % 50 %Vis input Vos output
74HC_HCT4053_4 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 — 9 May 2006 20 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer (1) Measurement points are given inTable12. Fig 13. Turn-ON and turn-OFF times Table 12: Measurement points Type Input VM 74HC4053 0.5V CC 74HCT4053 1.3 V 001aae330 tPLZ tPHZ switch OFF switch ONswitch ON Vos output Vos output E, Sn inputs VM VI 0 V 90 % 10 % tPZL tPZH 50 % 50 %
74HC_HCT4053_4 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 — 9 May 2006 21 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer [1] VI values: a) For74HC4053: VI=V CC . b) For74HCT4053: VI=3V . Test data is given inTable13. R T = Termination resistance should be equal to output impedance Zo of the pulse generator. C L = Load capacitance including jig and probe capacitance. R L = Load resistor. S1 = Test selection switch. Fig 14. Load circuitry for switching times Table 13: Test data Test Input Load S1 position VI Vis tr, tf C L R L at fmax other tPHL , tPLH [1] pulse < 2 ns 6 ns 15 pF , 50 pF 1 k Ω open tPZH , tPHZ [1] VCC < 2 ns 6 ns 15 pF , 50 pF 1 k Ω VEE tPZL , tPLZ [1] VEE < 2 ns 6 ns 15 pF , 50 pF 1 k Ω VCC VM VM tW tW 10 % 90 % 0 V VI VI negative pulse positive pulse 0 V VM VM 90 % 10 % tf tr tr tf 001aae382 VCC VCC open GND VEE VI Vos DUT C LR T R L S1 PULSE GENERATOR Vis
74HC_HCT4053_4 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 — 9 May 2006 22 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer 14. Additional dynamic characteristics [1] Adjust input voltage Vis to 0 dBm level (0 dBm = 1 mW into 600Ω ). [2] Control inputE or Sn, with square-wave between VCC and GND. [3] Adjust input voltage Vis to 0 dBm level at Vos for 1 MHz (0 dBm = 1 mW into 50Ω ). Table 14: Additional dynamic characteristics 74HC4053 and 74HCT4053 GND = 0 V; Tamb =2 5°C. Vis is the input voltage at an nYn or nZ terminal, whichever is assigned as an input. Vos is the output voltage at an nYn or nZ terminal, whichever is assigned as an output. Symbol Parameter Conditions Min Typ Max Unit dsin sine wave distortion RL = 10 kΩ ; CL = 50 pF; seeFigure15 fi= 1 kHz VCC = 2.25 V; VEE = −2.25 V; Vis= 4.0 V (p-p) - 0.04 - % VCC = 4.5 V; VEE =−4.5 V; Vis = 8.0 V (p-p) - 0.02 - % fi=1 0k H z VCC = 2.25 V; VEE = −2.25 V; Vis= 4.0 V (p-p) - 0.12 - % VCC = 4.5 V; VEE =−4.5 V; Vis = 8.0 V (p-p) - 0.06 - % α (OFF)(ft) OFF-state feed-through attenuation R L = 600Ω ; CL = 50 pF; fi= 1 MHz; see Figure16 [1] VCC = 2.25 V; VEE =−2.25 V - −50 - dB VCC = 4.5 V; VEE =−4.5 V - −50 - dB Vct(sw-sw) crosstalk between switches R L = 600Ω ; CL = 50 pF; fi= 1 MHz; see Figure17 [1] VCC = 2.25 V; VEE =−2.25 V - −60 - dB VCC = 4.5 V; VEE =−4.5 V - −60 - dB Vct(d-sw) crosstalk between digital inputs and switch V CC = 4.5 V; RL = 600 kΩ ; CL = 50 pF; fi= 1 MHz; seeFigure18 [2] VEE = 0 V - 110 - mV VEE =−4.5 V - 220 - mV f(-3dB) −3 dB frequency response R L =5 0Ω ; CL = 10 pF; seeFigure19 [3] VCC = 2.25 V; VEE =−2.25 V - 160 - MHz VCC = 4.5 V; VEE =−4.5 V - 170 - MHz Fig 15. Test circuit for measuring sine wave distortion 001aae132 10 mF R L VosVis C L dB nYn or nZ nZ or nYn GND channel ON
74HC_HCT4053_4 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 — 9 May 2006 23 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer a. Feed-through as function of the frequency b. Test circuit Fig 16. Typical switch OFF signal feed-through as a function of frequency 001aae332 fi (kHz) 10 10 5 106104102 103 −60 −40 −80 −20 α (OFF)(ft) (dB) −100 001aae133 0.1 mF R L VosVis C L dB GNDchannel OFF nYn or nZ nZ or nYn
74HC_HCT4053_4 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 — 9 May 2006 24 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer a. Switch ON b. Switch OFF Fig 17. Test circuits for measuring crosstalk between any two switches Fig 18. Test circuit for measuring crosstalk between digital inputs and switch 001aae134 0.1 mF R L R L VosVis C L dB nYn or nZ nZ or nYn GND channel ON 001aae259 R L VosVis C L dB GND channel OFF R L nYn or nZ nZ or nYn DUT 001aae135 2R L2R L 2R L2R L nZ or nYn nYn or nZ C L oscilloscope VCC VCC GND VEE Vct(d-sw) Sn or E
74HC_HCT4053_4 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 — 9 May 2006 25 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer a. Typical frequency response b. Test circuit Fig 19. Typical frequency response 001aad551 f (kHz) 10 10 5 106104102 103 Vos (dB) 001aae132 10 mF R L VosVis C L dB nYn or nZ nZ or nYn GND channel ON
74HC_HCT4053_4 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 — 9 May 2006 26 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer 15. Package outline Fig 20. Package outline SOT38-4 (DIP16) REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA SOT38-4 95-01-14 03-02-13 M H c (e )1 M E A L seating plane w M e D A 2 Z E pin 1 index b 0 5 10 mm scale Note 1. Plastic or metal protrusions of 0.25 mm (0.01 inch) maximum per side are not included. UNIT A max. 12 b1 (1) (1) (1) b2 cD E e M ZHL mm DIMENSIONS (inch dimensions are derived from the original mm dimensions) A min. A max. b max.wM Ee1 1.73 1.30 0.53 0.38 0.36 0.23 19.50 18.55 6.48 6.20 3.60 7.80 10.0 inches 0.068 0.051 0.021 0.015 0.014 0.009 1.25 0.85 0.049 0.033 0.77 0.73 0.26 0.24 0.14 0.31 0.39 DIP16: plastic dual in-line package; 16 leads (300 mil) SOT38-4
74HC_HCT4053_4 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 — 9 May 2006 27 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer Fig 21. Package outline SOT109-1 (SO16) X w M q AA 1 A 2 bp D H E Lp Q detail X E Z e c L v M A (A )3 A y pin 1 index UNIT A max. A 1 A 2 A 3 bp cD (1) E (1) (1)eH E LL p QZ ywv q REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm inches 1.75 0.25 0.10 1.45 1.25 0.25 0.49 0.36 0.25 0.19 10.0 9.8 4.0 3.8 1.27 6.2 5.8 0.7 0.6 0.7 0.3 8 o o 0.25 0.1 DIMENSIONS (inch dimensions are derived from the original mm dimensions) Note 1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included. 1.0 0.4 SOT109-1 99-12-27 03-02-19 076E07 MS-012 0.069 0.010 0.004 0.057 0.049 0.01 0.019 0.014 0.0100 0.0075 0.39 0.38 0.16 0.15 0.05 1.05 0.0410.244 0.228 0.028 0.020 0.028 0.0120.01 0.25 0.01 0.0040.039 0.016 0 2.5 5 mm scale SO16: plastic small outline package; 16 leads; body width 3.9 mm SOT109-1
74HC_HCT4053_4 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 — 9 May 2006 28 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer Fig 22. Package outline SOT338-1 (SSOP16) UNIT A 1 A 2 A 3 bp cD (1) E (1) eH E LL p QZ ywv q REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm 0.21 0.05 1.80 1.65 0.25 0.38 0.25 0.20 0.09 6.4 6.0 5.4 5.2 0.65 1.257.9 7.6 1.03 0.63 0.9 0.7 1.00 0.55 o o0.130.2 0.1 DIMENSIONS (mm are the original dimensions) Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. SOT338-1 99-12-27 03-02-19 (1) w M bp D H E E Z e c v M A X A y 1 8 16 9 q AA 1 A 2 Lp Q detail X L (A )3 MO-150 pin 1 index 0 2.5 5 mm scale SSOP16: plastic shrink small outline package; 16 leads; body width 5.3 mm SOT338-1 A max.
74HC_HCT4053_4 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 — 9 May 2006 29 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer Fig 23. Package outline SOT403-1 (TSSOP16) UNIT A 1 A 2 A 3 bp cD (1) E (2) (1)eH E LL p QZ ywv q REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm 0.15 0.05 0.95 0.80 0.30 0.19 0.2 0.1 5.1 4.9 4.5 4.3 0.65 6.6 6.2 0.4 0.3 0.40 0.06 o o0.13 0.10.21 DIMENSIONS (mm are the original dimensions) Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included. 0.75 0.50 SOT403-1 MO-153 99-12-27 03-02-18 w M bp D Z e 0.25 16 9 q AA 1 A 2 Lp Q detail X L (A )3 H E E c v M A XA y 0 2.5 5 mm scale TSSOP16: plastic thin shrink small outline package; 16 leads; body width 4.4 mm SOT403-1 A max. 1.1 pin 1 index
74HC_HCT4053_4 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 — 9 May 2006 30 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer Fig 24. Package outline SOT763-1 (DHVQFN16) terminal 1 index area 0.51 A 1 EhbUNIT ye 0.2 c REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm 3.6 3.4 D h 2.15 1.85 2.6 2.4 1.15 0.85 2.50.30 0.18 0.05 0.00 0.05 0.1 DIMENSIONS (mm are the original dimensions) 0.5 0.3 L 0.1 v 0.05 w 0 2.5 5 mm scale SOT763-1 DHVQFN16: plastic dual in-line compatible thermal enhanced very thin quad flat package; no leads; 16 terminals; body 2.5 x 3.5 x 0.85 mm A (1) max. A c detail X yy1 Ce L Eh D h e b 15 10 X D E C B A terminal 1 index area AC C Bv M w M E (1) Note 1. Plastic or metal protrusions of 0.075 mm maximum per side are not included. D (1) 02-10-17 03-01-27
74HC_HCT4053_4 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 — 9 May 2006 31 of 33 Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer 16. Abbreviations 17. Revision history Table 15: Abbreviations Acronym Description CMOS Complementary Metal Oxide Semiconductor HBM Human Body Model ESD ElectroStatic Discharge MM Machine Model DUT Device Under Test Table 16: Revision history Document ID Release date Data sheet status Change notice Doc. number Supersedes 74HC_HCT4053_4 20060509 Product data sheet - - 74HC_HCT4053_3 Modifications:
- Section 5 “Ordering information”: errors corrected, type numbers in wrong order and SOT38-4 is the package for types 74HC4053N and 74HCT4053N 74HC_HCT4053_3 20060315 Product data sheet - - 74HC_HCT4053_ CNV_2 Modifications: • The format of this data sheet has been redesigned to comply with the new presentation and information standard of Philips Semiconductors.
- Added type numbers 74HC4053BQ and 74HCT4053BQ (DHVQFN16) package to Section5 “Orderinginformation”,Section7 “Pinninginformation”and Section15 “Package outline” 74HC_HCT4053_CNV_2 19901201 Product specification - - -
Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer 74HC_HCT4053_4 © Koninklijke Philips Electronics N.V. 2006. All rights reserved. Product data sheet Rev. 04 — 9 May 2006 32 of 33 18. Data sheet status [1] Please consult the most recently issued data sheet before initiating or completing a design. [2] The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com. [3] For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status. 19. Definitions Short-form specification —The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. 20. Disclaimers Life support —These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes —Philips Semiconductors reserves the right to make changes in the products - including circuits, standard cells, and/or software - described or contained herein in order to improve design and/or performance. When the product is in full production (status ‘Production’), relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. 21. Trademarks Notice —All referenced brands, product names, service names and trademarks are the property of their respective owners. 22. Contact information For additional information, please visit: http://www.semiconductors.philips.com For sales office addresses, send an email to: sales.addresses@www.semiconductors.philips.com Level Data sheet status[1] Product status[2][3] Definition I Objective data Development This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice. II Preliminary data Qualification This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. III Product data Production This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN).
© Koninklijke Philips Electronics N.V. 2006 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. Date of release: 9 May 2006 Document number: 74HC_HCT4053_4 Published in The Netherlands Philips Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer 23. Contents