DATASHEET SEARCH SITE

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 32

Technical content

  1. General description The 74HC4053; 74HCT4053 is a high-speed Si-gate CMOS device and is pin compatible with the HEF4053B. It is specified in compliance with JEDEC standard no. 7A. The 74HC4053; 74HCT4053 is triple 2-channel analog multiplexer/demultiplexer with a common enable input (E). Each multiplexer/demultiplexer has two independent inputs/outputs (nY0 and nY1), a common input/output (nZ) and three digital select inputs (Sn). With E LOW, one of the two switches is selected (low-impedance ON-state) by S1 to S3. With E HIGH, all switches are in the high-impedance OFF-state, independent of S1 to S3. V CC and GND are the supply voltage pins for the digital control inputs (S0 to S2, and E). The VCC to GND ranges are 2.0 V to 10.0 V for 74HC4053 and 4.5 V to 5.5 V for 74HCT4053. The analog inputs/outputs (nY0 to nY1, and nZ) can swing between VCC as a positive limit and VEE as a negative limit. VCC  VEE may not exceed 10.0 V. For operation as a digital multiplexer/demultiplexer, VEE is connected to GND (typically ground). 2. Features and benefits  Wide analog input voltage range from 5 V to +5 V  Low ON resistance:  80  (typical) at VCC  VEE =4 . 5V  70  (typical) at VCC  VEE =6 . 0V  60  (typical) at VCC  VEE =9 . 0V  Logic level translation: to enable 5 V logic to communicate with 5 V analog signals  Typical ‘break before make’ built-in  ESD protection:  HBM JESD22-A114F exceeds 2000 V  MM JESD22-A115-A exceeds 200 V  CDM JESD22-C101E exceeds 1000 V  Multiple package options  Specified from 40 Ct o + 8 5C and 40 Ct o + 1 2 5C 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer Rev. 8 — 19 July 2012 Product data sheet

Table 1. Ordering information

Product data sheet Rev. 8 — 19 July 2012 3 of 32 NXP Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer 5. Functional diagram Fig 1. Functional diagram 001aak341 LOGIC LEVEL CONVERSION VCC 13 1Y1 LOGIC LEVEL CONVERSION DECODER LOGIC LEVEL CONVERSION 12 1Y0 14 1Z 1 2Y1 2 2Y0 15 2Z 3 3Y1 5 3Y0 43 Z 10S2 VEEGND E Fig 2. Logic symbol Fig 3. IEC logic symbol 001aae125 1Y0 12 1Y1 S2 10 S3 9 6 E 2Y0 2 2Y1 1 3Y0 5 3Y1 3 3Z 4 2Z 15 1Z 14 001aae126 6 EN 11 # MUX/DMUX × 0 114 10 2 115 9 5

Product data sheet Rev. 8 — 19 July 2012 4 of 32 NXP Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer 6. Pinning information

6.1 Pinning

Fig 4. Schematic diagram (one switch) 001aad544 from logic VCC VEE VEE VCC VCC VEE Y Z VCC (1) This is not a supply pin. The substrate is attached to this pad using conductive die attach material. There is no electrical or mechanical requirement to solder this pad. However, if it is soldered, the solder land should remain floating or be connected to VCC. Fig 5. Pin configuration DIP16, SO16, and (T)SSOP16 Fig 6. Pin co nfiguration DHVQFN16 74HC4053 74HCT4053 2Y1 VCC 2Y0 2Z 3Y1 1Z 3Z 1Y1 3Y0 1Y0 ES 1 VEE S2 GND S3 001aae127 001aae128 VEE S2 ES 1 3Y0 1Y0 3Z 1Y1 3Y1 1Z 2Y0 2Z GND 2Y1 VCC Transparent top view 7 10 6 11 5 12 4 13 3 14 2 15 terminal 1 index area VCC(1) 74HC4053 74HCT4053

6.2 Pin description

[1] H = HIGH voltage level; L = LOW voltage level; X = don’t care. there is no limit for the voltage drop across the switch, but the voltages at nYn and nZ may not exceed VCC or VEE. [2] For DIP16 packages: above 70 C the value of Ptot derates linearly with 12 mW/K. Table 2. Pin description Table 3. Function table [1] Table 4. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to VSS = 0 V (ground).

[3] For SO16 packages: above 70 C the value of Ptot derates linearly with 8 mW/K. For SSOP16 and TSSOP16 packages: above 60 C the value of Ptot derates linearly with 5.5 mW/K. For DHVQFN16 packages: above 60 C the value of Ptot derates linearly with 4.5 mW/K.

  1. Recommended operating conditions

Table 5. Recommended operating conditions

Table 6. R ON resistance per switch for 74HC4053 and 74HCT4053 VI = VIH or VIL; for test circuit see Figure 9. Vis is the input voltage at a nYn or nZ terminal, whichever is assigned as an input. Vos is the output voltage at a nYn or nZ terminal, whichever is assigned as an output.

2 V, it is recommended to use these devices only for transmitting digital signals. Table 6. R ON resistance per switch for 74HC4053 and 74HCT4053 …continued VI = VIH or VIL; for test circuit see Figure 9. Vis is the input voltage at a nYn or nZ terminal, whichever is assigned as an input. Vos is the output voltage at a nYn or nZ terminal, whichever is assigned as an output.

Vis =0Vt o( V CC  VEE). Vis =0Vt o( V CC  VEE). Table 7. Static characteristics for 74HC4053 Voltages are referenced to GND (ground = 0 V). Vis is the input voltage at pins nYn or nZ, whichever is assigned as an input. Vos is the output voltage at pins nZ or nYn, whichever is assigned as an output.

Table 7. Static characteristics for 74HC4053 …continued Voltages are referenced to GND (ground = 0 V). is is the input voltage at pins nYn or nZ, whichever is assigned as an input. Vos is the output voltage at pins nZ or nYn, whichever is assigned as an output.

Voltages are referenced to GND (ground = 0 V). is is the input voltage at pins nYn or nZ, whichever is assigned as an input. Vos is the output voltage at pins nZ or nYn, whichever is assigned as an output. Table 8. Static characteristics for 74HCT4053 Voltages are referenced to GND (ground = 0 V). Vis is the input voltage at pins nYn or nZ, whichever is assigned as an input. Vos is the output voltage at pins nZ or nYn, whichever is assigned as an output.

Table 8. Static characteristics for 74HCT4053 …continued Voltages are referenced to GND (ground = 0 V). Vis is the input voltage at pins nYn or nZ, whichever is assigned as an input. Vos is the output voltage at pins nZ or nYn, whichever is assigned as an output.

Vis = VCC and Vos = open-circuit. Vis = VEE and Vos = open-circuit. Table 9. Dynamic characteristics for 74HC4053 GND = 0 V; tr =t f =6n s ; CL = 50 pF; for test circuit see Figure 15. Vis is the input voltage at a nYn or nZ terminal, whichever is assigned as an input. Vos is the output voltage at a nYn or nZ terminal, whichever is assigned as an output.

Table 9. Dynamic characteristics for 74HC4053 …continued GND = 0 V; tr =t f =6n s ; CL = 50 pF; for test circuit see Figure 15. Vis is the input voltage at a nYn or nZ terminal, whichever is assigned as an input. Vos is the output voltage at a nYn or nZ terminal, whichever is assigned as an output.

GND = 0 V; tr =t f =6n s ; CL = 50 pF; for test circuit see Figure 15. Vis is the input voltage at a nYn or nZ terminal, whichever is assigned as an input. Vos is the output voltage at a nYn or nZ terminal, whichever is assigned as an output.

[1] t pd is the same as tPHL and tPLH. [2] t on is the same as tPZH and tPZL. [3] t off is the same as tPHZ and tPLZ. [4] C PD is used to determine the dynamic power dissipation (PD in W). GND = 0 V; tr =t f =6n s ; CL = 50 pF; for test circuit see Figure 15. Vis is the input voltage at a nYn or nZ terminal, whichever is assigned as an input. Vos is the output voltage at a nYn or nZ terminal, whichever is assigned as an output. Table 10. Dynamic characteristics for 74HCT4053 GND = 0 V; tr =t f =6n s ; CL = 50 pF; for test circuit see Figure 15. Vis is the input voltage at a nYn or nZ terminal, whichever is assigned as an input. Vos is the output voltage at a nYn or nZ terminal, whichever is assigned as an output.

Table 10. Dynamic characteristics for 74HCT4053 …continued GND = 0 V; tr =t f =6n s ; CL = 50 pF; for test circuit see Figure 15. Vis is the input voltage at a nYn or nZ terminal, whichever is assigned as an input. Vos is the output voltage at a nYn or nZ terminal, whichever is assigned as an output.

[1] t pd is the same as tPHL and tPLH. [2] t on is the same as tPZH and tPZL. [3] t off is the same as tPHZ and tPLZ. [4] C PD is used to determine the dynamic power dissipation (PD in W). GND = 0 V; tr =t f =6n s ; CL = 50 pF; for test circuit see Figure 15. Vis is the input voltage at a nYn or nZ terminal, whichever is assigned as an input. Vos is the output voltage at a nYn or nZ terminal, whichever is assigned as an output.

Product data sheet Rev. 8 — 19 July 2012 19 of 32 NXP Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer For 74HC4053: VM =0 . 5  VCC. For 74HCT4053: VM =1 . 3V . Fig 14. Turn-on and turn-off times 001aad556 tPLZ tPHZ switch OFF switch ONswitch ON Vos output Vos output E, Sn inputs VM VI 0 V 90 % 10 % tPZL tPZH 50 % 50 % Definitions for test circuit; see Table 11: RT = termination resistance should be equal to the output impedance Zo of the pulse generator. CL = load capacitance including jig and probe capacitance. RL = load resistance. S1 = Test selection switch. Fig 15. Test circuit for me asuring AC performance VM VM tW tW 10 % 90 % 0 V VI VI negative pulse positive pulse 0 V VM VM 90 % 10 % tf tr tr tf 001aae382 VCC VCC open GND VEE VI Vos DUT CLRT RL S1 PULSE GENERATOR Vis

[1] t r = tf = 6 ns; when measuring fmax, there is no constraint to tr and tf with 50 % duty factor.

11.1 Additional dynami c characteristics

[1] Adjust input voltage V is to 0 dBm level (0 dBm = 1 mW into 600 ). [2] Adjust input voltage V is to 0 dBm level at Vos for 1 MHz (0 dBm = 1 mW into 50 ). Table 11. Test data Table 12. Additional dynamic characteristics Recommended conditions and typical values; GND = 0 V; Tamb =2 5 C; CL =5 0p F . Vis is the input voltage at pins nYn or nZ, whichever is assigned as an input. Vos is the output voltage at pins nYn or nZ, whichever is assigned as an output.

Product data sheet Rev. 8 — 19 July 2012 21 of 32 NXP Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer Fig 16. Test circuit for measuring sine-wave distortion dB 001aah829 nYn/nZ10 μF Vis Vos nZ/nYn CLRL Sn GNDVEE VCC VCC = 4.5 V; GND = 0 V; VEE = 4.5 V; RL = 600 ; RS =1k . a. Test circuit b. Isolation (OFF-state) as a function of frequency Fig 17. Test circuit for measuring isolation (OFF-state) dB 001aah871 nYn/nZ0.1 μF Vis Vos nZ/nYn CLRL Sn GNDVEE VCC 001aae332 fi (kHz) 10 10 5 106104102 103 −60 −40 −80 −20 αiso (dB) −100

Product data sheet Rev. 8 — 19 July 2012 22 of 32 NXP Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer Fig 18. Test circuits for measuring crosst alk between any two switches/multiplexers dB 001aah873 nYn/nZ Vos nZ/nYn CLRLRL Sn GNDVEE VCC nYn/nZ0.1 μF Vis nZ/nYn CLRL RL Sn GNDVEE VCC Fig 19. Test circuit for measuring crosst alk between control input and any switch oscilloscope 001aah913 nYn Vct nZ 2RL 2RL 2RL 2RL Sn, E GNDVEE VCC G

Product data sheet Rev. 8 — 19 July 2012 23 of 32 NXP Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer VCC = 4.5 V; GND = 0 V; VEE = 4.5 V; RL =5 0 ; RS =1k . a. Test circuit b. Typical frequency response Fig 20. Test circuit for frequency response dB 001aah829 nYn/nZ10 μF Vis Vos nZ/nYn CLRL Sn GNDVEE VCC 001aad551 f (kHz) 10 10 5 106104102 103 Vos (dB)

Product data sheet Rev. 8 — 19 July 2012 24 of 32 NXP Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer 12. Package outline Fig 21. Package outline SOT38-4 (DIP16) REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA SOT38-4 95-01-14 03-02-13 MH c (e )1 ME A L seating plane w M e D Z E pin 1 index b 0 5 10 mm scale Note 1. Plastic or metal protrusions of 0.25 mm (0.01 inch) maximum per side are not included. UNIT A max. 12 b1 (1) (1) (1) b2 cD E e M ZHL mm DIMENSIONS (inch dimensions are derived from the original mm dimensions) A min. A max. b max.wMEe1 1.73 1.30 0.53 0.38 0.36 0.23 19.50 18.55 6.48 6.20 3.60 7.80 10.0 inches 0.068 0.051 0.021 0.015 0.014 0.009 1.25 0.85 0.049 0.033 0.77 0.73 0.26 0.24 0.14 0.31 0.39 DIP16: plastic dual in-line package; 16 leads (300 mil) SOT38-4

Product data sheet Rev. 8 — 19 July 2012 25 of 32 NXP Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer Fig 22. Package outline SOT109-1 (SO16) X w M θ AA1 bp D HE Lp Q detail X E Z e c L v M A (A )3 A y pin 1 index UNIT A max. A1 A2 A3 bp cD (1) E(1) (1)eH E LL p QZ y w v θ REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm inches 1.75 0.25 0.10 1.45 1.25 0.25 0.49 0.36 0.25 0.19 10.0 9.8 4.0 3.8 1.27 6.2 5.8 0.7 0.6 0.7 0.3 8 o o 0.25 0.1 DIMENSIONS (inch dimensions are derived from the original mm dimensions) Note 1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included. 1.0 0.4 SOT109-1 99-12-27 03-02-19 076E07 MS-012 0.069 0.010 0.004 0.057 0.049 0.01 0.019 0.014 0.0100 0.0075 0.39 0.38 0.16 0.15 0.05 1.05 0.0410.244 0.228 0.028 0.020 0.028 0.0120.01 0.25 0.01 0.0040.039 0.016 0 2.5 5 mm scale SO16: plastic small outline package; 16 leads; body width 3.9 mm SOT109-1

Product data sheet Rev. 8 — 19 July 2012 26 of 32 NXP Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer Fig 23. Package outline SOT338-1 (SSOP16) UNIT A1 A2 A3 bp cD (1) E (1) eH E LL p QZ y w v θ REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm 0.21 0.05 1.80 1.65 0.25 0.38 0.25 0.20 0.09 6.4 6.0 5.4 5.2 0.65 1.257.9 7.6 1.03 0.63 0.9 0.7 1.00 0.55 o o0.130.2 0.1 DIMENSIONS (mm are the original dimensions) Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. SOT338-1 99-12-27 03-02-19 (1) w M bp D HE E Z e c v M A X A y 1 8 16 9 θ AA1 Lp Q detail X L (A )3 MO-150 pin 1 index 0 2.5 5 mm scale SSOP16: plastic shrink small outline package; 16 leads; body width 5.3 mm SOT338-1 A max.

Product data sheet Rev. 8 — 19 July 2012 27 of 32 NXP Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer Fig 24. Package outline SOT403-1 (TSSOP16) UNIT A1 A2 A3 bp cD (1) E (2) (1)eH E LL p QZ y w v θ REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm 0.15 0.05 0.95 0.80 0.30 0.19 0.2 0.1 5.1 4.9 4.5 4.3 0.65 6.6 6.2 0.4 0.3 0.40 0.06 o o0.13 0.10.21 DIMENSIONS (mm are the original dimensions) Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included. 0.75 0.50 SOT403-1 MO-153 99-12-27 03-02-18 w M bp D Z e 0.25 16 9 θ AA1 Lp Q detail X L (A )3 HE E c v M A XA y 0 2.5 5 mm scale TSSOP16: plastic thin shrink small outline package; 16 leads; body width 4.4 mm SOT403-1 A max. 1.1 pin 1 index

Product data sheet Rev. 8 — 19 July 2012 28 of 32 NXP Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer Fig 25. Package outline SOT763-1 (DHVQFN16) terminal 1 index area 0.51 A1 EhbUNIT ye 0.2 c REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm 3.6 3.4 Dh 2.15 1.85 2.6 2.4 1.15 0.85 2.50.30 0.18 0.05 0.00 0.05 0.1 DIMENSIONS (mm are the original dimensions) 0.5 0.3 L 0.1 v 0.05 w 0 2.5 5 mm scale SOT763-1 DHVQFN16: plastic dual in-line compatible thermal enhanced very thin quad flat package; no leads; 16 terminals; body 2.5 x 3.5 x 0.85 mm A(1) max. A c detail X yy1 Ce L Eh Dh e b 15 10 X D E C B A terminal 1 index area A C C Bv M w M E(1) Note 1. Plastic or metal protrusions of 0.075 mm maximum per side are not included. D(1) 02-10-17 03-01-27

Table 13. Abbreviations Table 14. Revision history

  • CDM added to features. 74HC_HCT4053 v.7 20111213 Product data sheet - 74HC_HCT4053 v.6 Modifications:
  • Legal pages updated. 74HC_HCT4053 v.6 20110511 Product data sheet - 74HC_HCT4053 v.5 74HC_HCT4053 v.5 20110118 Product data sheet - 74HC_HCT4053 v.4 74HC_HCT4053 v.4 20060509 Product data sheet - 74HC_HCT4053 v.3 74HC_HCT4053 v.3 20060315 Product data sheet - 74HC_HCT4053_CNV v.2 74HC_HCT4053_CNV v.2 19901201 Product specification - -

Product data sheet Rev. 8 — 19 July 2012 30 of 32 NXP Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer 15. Legal information

15.1 Data sheet status

[1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com.

15.2 Definitions

Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification — The information and data provided in a Product data sheet shall define the specification of the product as agreed between NXP Semiconductors and its customer, unless NXP Semiconductors and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the NXP Semiconductors product is deemed to offer functions and qualities beyond those described in the Product data sheet.

15.3 Disclaimers

Limited warranty and liability — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. NXP Semiconductors takes no responsibility for the content in this document if provided by an information source outside of NXP Semiconductors. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use — NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors and its suppliers accept no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product design. It is customer’s sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s applications or products, or the application or use by customer’s third party customer(s). Customer is responsible for doing all necessary testing for the customer’s applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customer’s third party customer(s). NXP does not accept any liability in this respect. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale — NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms , unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer’s general terms and conditions with regard to the purchase of NXP Semiconductors products by customer. No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification.

Product data sheet Rev. 8 — 19 July 2012 31 of 32 NXP Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities. Non-automotive qualified products — Unless this data sheet expressly states that this specific NXP Semiconductors product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. NXP Semiconductors accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without NXP Semiconductors’ warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond NXP Semiconductors’ specifications such use shall be solely at customer’s own risk, and (c) customer fully indemnifies NXP Semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NXP Semiconductors’ standard warranty and NXP Semiconductors’ product specifications. Translations — A non-English (translated) version of a document is for reference only. The English version shall prevail in case of any discrepancy between the translated and English versions.

15.4 Trademarks

Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 16. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com

NXP Semiconductors 74HC4053; 74HCT4053 Triple 2-channel analog multiplexer/demultiplexer © NXP B.V. 2012. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 19 July 2012 Document identifier: 74HC_HCT4053 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. 17. Contents