74HC4052 NXP
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 27
Technical content
- General description The 74HC4052; 74HCT4052 is a high-speed Si-gate CMOS device and is pin compatible with the HEF4052B. The device is specified in compliance with JEDEC standard no. 7A. The 74HC4052; 74HCT4052 is a dual 4-channel analog multiplexer/demultiplexer with common select logic. Each multiplexer has four independent inputs/outputs (pins nY0 to nY3) and a common input/output (pin nZ). The common channel select logics include two digital select inputs (pins S0 and S1) and an active LOW enable input (pin E). When pin E = LOW, one of the four switches is selected (low-impedance ON-state) with pins S0 and S1. When pin E = HIGH, all switches are in the high-impedance OFF-state, independent of pins S0 and S1. VCC and GND are the supply voltage pins for the digital control inputs (pins S0, S1 and E). The VCC to GND ranges are 2.0 V to 10.0 V for the 74HC4052 and 4.5 V to 5.5 V for the 74HCT4052. The analog inputs/outputs (pins nY0 to nY3 and nZ) can swing between VCC as a positive limit and VEE as a negative limit. VCC − VEE may not exceed 10.0 V. For operation as a digital multiplexer/demultiplexer, VEE is connected to GND (typically ground). 2. Features Wide analog input voltage range from −5 V to +5 V Low ON resistance: 80 Ω (typical) at VCC − VEE = 4.5 V 70 Ω (typical) at VCC − VEE = 6.0 V 60 Ω (typical) at VCC − VEE = 9.0 V Logic level translation: to enable 5 V logic to communicate with ±5 V analog signals Typical ‘break before make’ built-in Complies with JEDEC standard no. 7A ESD protection: HBM JESD22-A114F exceeds 2000 V MM JESD22-A115-A exceeds 200 V Specified from −40 °C to +85 °C and −40 °C to +125 °C 3. Applications Analog multiplexing and demultiplexing Digital multiplexing and demultiplexing Signal gating 74HC4052; 74HCT4052 Dual 4-channel analog multiplexer/demultiplexer Rev. 06 — 11 January 2010 Product data sheet
74HC_HCT4052_6 © NXP B.V. 2010. All rights reserved. Table 1. Ordering information
74HC_HCT4052_6 © NXP B.V. 2010. All rights reserved. Product data sheet Rev. 06 — 11 January 2010 3 of 27 NXP Semiconductors 74HC4052; 74HCT4052 Dual 4-channel analog multiplexer/demultiplexer Fig 3. Schematic diagram (one switch) mnb043 from logic VCC VEE VEE VCC VCC VEE nYn nZ VCC Fig 4. Functional diagram 001aah872 1-OF-4 DECODER LOGIC LEVEL CONVERSION VEEVSS VDD 1316 E 1Y0 1Y1 1Y2 1Y3 2Y0 2Y1 2Y2 2Y34
74HC_HCT4052_6 © NXP B.V. 2010. All rights reserved.
6.1 Pinning
6.2 Pin description
Table 2. Pin description
74HC_HCT4052_6 © NXP B.V. 2010. All rights reserved.
7.1 Function table
voltage drop across the switch, but the voltages at pins nYn and nZ may not exceed VCC or VEE. [2] For DIP16 packages: above 70 °C the value of Ptot derates linearly with 12 mW/K. For SO16 packages: above 70 °C the value of Ptot derates linearly with 8 mW/K. For SSOP16 and TSSOP16 packages: above 60 °C the value of Ptot derates linearly with 5.5 mW/K. For DHVQFN16 packages: above 60 °C the value of Ptot derates linearly with 4.5 mW/K. Table 3. Function table [1] Table 4. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to VEE = GND (ground = 0 V).
74HC_HCT4052_6 © NXP B.V. 2010. All rights reserved.
- Recommended operating conditions
Table 5. Recommended operating conditions
74HC_HCT4052_6 © NXP B.V. 2010. All rights reserved. Table 6. R ON resistance per switch for 74HC4052 and 74HCT4052 VI = VIH or VIL; for test circuit see Figure 9. Vis is the input voltage at a nYn or nZ terminal, whichever is assigned as an input. Vos is the output voltage at a nYn or nZ terminal, whichever is assigned as an output.
74HC_HCT4052_6 © NXP B.V. 2010. All rights reserved. [1] All typical values are measured at T amb = 25 °C. 2 V, it is recommended to use these devices only for transmitting digital signals. Table 6. R ON resistance per switch for 74HC4052 and 74HCT4052 …continued VI = VIH or VIL; for test circuit see Figure 9. Vis is the input voltage at a nYn or nZ terminal, whichever is assigned as an input. Vos is the output voltage at a nYn or nZ terminal, whichever is assigned as an output. Vis = 0 V to (VCC − VEE). Vis = 0 V to (VCC − VEE).
74HC_HCT4052_6 © NXP B.V. 2010. All rights reserved. Table 7. Static characteristics for 74HC4052 Voltages are referenced to GND (ground = 0 V). Vis is the input voltage at pins nYn or nZ, whichever is assigned as an input. Vos is the output voltage at pins nZ or nYn, whichever is assigned as an output.
74HC_HCT4052_6 © NXP B.V. 2010. All rights reserved. [1] All typical values are measured at T amb = 25 °C. Table 7. Static characteristics for 74HC4052 …continued Voltages are referenced to GND (ground = 0 V). Vis is the input voltage at pins nYn or nZ, whichever is assigned as an input. Vos is the output voltage at pins nZ or nYn, whichever is assigned as an output. Table 8. Static characteristics for 74HCT4052 Voltages are referenced to GND (ground = 0 V). Vis is the input voltage at pins nYn or nZ, whichever is assigned as an input. Vos is the output voltage at pins nZ or nYn, whichever is assigned as an output.
74HC_HCT4052_6 © NXP B.V. 2010. All rights reserved. [1] All typical values are measured at T amb = 25 °C. Table 8. Static characteristics for 74HCT4052 …continued Voltages are referenced to GND (ground = 0 V). Vis is the input voltage at pins nYn or nZ, whichever is assigned as an input. Vos is the output voltage at pins nZ or nYn, whichever is assigned as an output. Vis = VCC and Vos = open-circuit. Vis = VEE and Vos = open-circuit.
74HC_HCT4052_6 © NXP B.V. 2010. All rights reserved. Table 9. Dynamic characteristics for 74HC4052 GND = 0 V; tr = tf = 6 ns; CL = 50 pF; for test circuit see Figure 15. Vis is the input voltage at a nYn or nZ terminal, whichever is assigned as an input. Vos is the output voltage at a nYn or nZ terminal, whichever is assigned as an output.
74HC_HCT4052_6 © NXP B.V. 2010. All rights reserved. [1] All typical values are measured at T amb = 25 °C. [2] t pd is the same as tPHL and tPLH. [3] t on is the same as tPZH and tPZL. [4] t off is the same as tPHZ and tPLZ. [5] C PD is used to determine the dynamic power dissipation (PD in μW). Table 9. Dynamic characteristics for 74HC4052 …continued GND = 0 V; tr = tf = 6 ns; CL = 50 pF; for test circuit see Figure 15. Vis is the input voltage at a nYn or nZ terminal, whichever is assigned as an input. Vos is the output voltage at a nYn or nZ terminal, whichever is assigned as an output. Table 10. Dynamic characteristics for 74HCT4052 GND = 0 V; tr = tf = 6 ns; CL = 50 pF; for test circuit see Figure 15. Vis is the input voltage at a nYn or nZ terminal, whichever is assigned as an input. Vos is the output voltage at a nYn or nZ terminal, whichever is assigned as an output.
74HC_HCT4052_6 © NXP B.V. 2010. All rights reserved. [1] All typical values are measured at T amb = 25 °C. [2] t pd is the same as tPHL and tPLH. [3] t on is the same as tPZH and tPZL. [4] t off is the same as tPHZ and tPLZ. [5] C PD is used to determine the dynamic power dissipation (PD in μW). Table 10. Dynamic characteristics for 74HCT4052 …continued GND = 0 V; tr = tf = 6 ns; CL = 50 pF; for test circuit see Figure 15. Vis is the input voltage at a nYn or nZ terminal, whichever is assigned as an input. Vos is the output voltage at a nYn or nZ terminal, whichever is assigned as an output.
74HC_HCT4052_6 © NXP B.V. 2010. All rights reserved. Product data sheet Rev. 06 — 11 January 2010 15 of 27 NXP Semiconductors 74HC4052; 74HCT4052 Dual 4-channel analog multiplexer/demultiplexer For 74HC4052: VM = 0.5 × VCC. For 74HCT4052: VM = 1.3 V. Fig 14. Turn-on and turn-off times 001aae330 tPLZ tPHZ switch OFF switch ONswitch ON Vos output Vos output E, Sn inputs VM VI 0 V 90 % 10 % tPZL tPZH 50 % 50 % Definitions for test circuit; see Table 11: RT = termination resistance should be equal to the output impedance Zo of the pulse generator. CL = load capacitance including jig and probe capacitance. RL = load resistance. S1 = Test selection switch. Fig 15. Test circuit for me asuring AC performance VM VM tW tW 10 % 90 % 0 V VI VI negative pulse positive pulse 0 V VM VM 90 % 10 % tf tr tr tf 001aae382 VCC VCC open GND VEE VI Vos DUT CLRT RL S1 PULSE GENERATOR Vis
74HC_HCT4052_6 © NXP B.V. 2010. All rights reserved. [1] t r = tf = 6 ns; when measuring fmax, there is no constraint to tr and tf with 50 % duty factor.
- Additional dynamic characteristics
[1] Adjust input voltage V is to 0 dBm level (0 dBm = 1 mW into 600 Ω). [2] Adjust input voltage V is to 0 dBm level at Vos for 1 MHz (0 dBm = 1 mW into 50 Ω). Table 11. Test data Table 12. Additional dynamic characteristics Recommended conditions and typical values; GND = 0 V; Tamb = 25 °C; CL = 50 pF . Vis is the input voltage at pins nYn or nZ, whichever is assigned as an input. Vos is the output voltage at pins nYn or nZ, whichever is assigned as an output.
74HC_HCT4052_6 © NXP B.V. 2010. All rights reserved. Product data sheet Rev. 06 — 11 January 2010 17 of 27 NXP Semiconductors 74HC4052; 74HCT4052 Dual 4-channel analog multiplexer/demultiplexer Fig 16. Test circuit for measuring sine-wave distortion dB 001aah829 nYn/nZ10 μF Vis Vos nZ/nYn CLRL Sn GNDVEE VCC VCC = 4.5 V; GND = 0 V; VEE = −4.5 V; RL = 50 Ω; RS = 1 kΩ. a. Test circuit b. Isolation (OFF-state) as a function of frequency Fig 17. Test circuit for measuring isolation (OFF-state) dB 001aah871 nYn/nZ0.1 μF Vis Vos nZ/nYn CLRL Sn GNDVEE VCC 001aae332 fi (kHz) 10 10 5 106104102 103 −60 −40 −80 −20 αiso (dB) −100
74HC_HCT4052_6 © NXP B.V. 2010. All rights reserved. Product data sheet Rev. 06 — 11 January 2010 18 of 27 NXP Semiconductors 74HC4052; 74HCT4052 Dual 4-channel analog multiplexer/demultiplexer Fig 18. Test circuits for measuring crosst alk between any two switches/multiplexers dB 001aah873 nYn/nZ Vos nZ/nYn CLRLRL Sn GNDVEE VCC nYn/nZ0.1 μF Vis nZ/nYn CLRL RL Sn GNDVEE VCC Fig 19. Test circuit for measuring crosst alk between control input and any switch oscilloscope 001aah913 nYn Vct nZ 2RL 2RL 2RL 2RL Sn, E GNDVEE VCC G
74HC_HCT4052_6 © NXP B.V. 2010. All rights reserved. Product data sheet Rev. 06 — 11 January 2010 19 of 27 NXP Semiconductors 74HC4052; 74HCT4052 Dual 4-channel analog multiplexer/demultiplexer VCC = 4.5 V; GND = 0 V; VEE = −4.5 V; RL = 50 Ω; RS = 1 kΩ. a. Test circuit b. Typical frequency response Fig 20. Test circuit for frequency response dB 001aah829 nYn/nZ10 μF Vis Vos nZ/nYn CLRL Sn GNDVEE VCC 001aad551 f (kHz) 10 10 5 106104102 103 Vos (dB)
74HC_HCT4052_6 © NXP B.V. 2010. All rights reserved. Product data sheet Rev. 06 — 11 January 2010 20 of 27 NXP Semiconductors 74HC4052; 74HCT4052 Dual 4-channel analog multiplexer/demultiplexer 13. Package outline Fig 21. Package outline SOT109-1 (SO16) X w M θ AA1 bp D HE Lp Q detail X E Z e c L v M A (A )3 A y pin 1 index UNIT A max. A1 A2 A3 bp cD (1) E(1) (1)eH E LL p QZ ywv θ REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm inches 1.75 0.25 0.10 1.45 1.25 0.25 0.49 0.36 0.25 0.19 10.0 9.8 4.0 3.8 1.27 6.2 5.8 0.7 0.6 0.7 0.3 8 o o 0.25 0.1 DIMENSIONS (inch dimensions are derived from the original mm dimensions) Note 1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included. 1.0 0.4 SOT109-1 99-12-27 03-02-19 076E07 MS-012 0.069 0.010 0.004 0.057 0.049 0.01 0.019 0.014 0.0100 0.0075 0.39 0.38 0.16 0.15 0.05 1.05 0.0410.244 0.228 0.028 0.020 0.028 0.0120.01 0.25 0.01 0.0040.039 0.016 0 2.5 5 mm scale SO16: plastic small outline package; 16 leads; body width 3.9 mm SOT109-1
74HC_HCT4052_6 © NXP B.V. 2010. All rights reserved. Product data sheet Rev. 06 — 11 January 2010 21 of 27 NXP Semiconductors 74HC4052; 74HCT4052 Dual 4-channel analog multiplexer/demultiplexer Fig 22. Package outline SOT338-1 (SSOP16) UNIT A 1 A2 A3 bp cD (1) E (1) eH E LL p QZ ywv θ REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm 0.21 0.05 1.80 1.65 0.25 0.38 0.25 0.20 0.09 6.4 6.0 5.4 5.2 0.65 1.257.9 7.6 1.03 0.63 0.9 0.7 1.00 0.55 o o0.130.2 0.1 DIMENSIONS (mm are the original dimensions) Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. SOT338-1 99-12-27 03-02-19 (1) w M bp D HE E Z e c v M A X A y 1 8 16 9 θ AA1 Lp Q detail X L (A )3 MO-150 pin 1 index 0 2.5 5 mm scale SSOP16: plastic shrink small outline package; 16 leads; body width 5.3 mm SOT338-1 A max.
74HC_HCT4052_6 © NXP B.V. 2010. All rights reserved. Product data sheet Rev. 06 — 11 January 2010 22 of 27 NXP Semiconductors 74HC4052; 74HCT4052 Dual 4-channel analog multiplexer/demultiplexer Fig 23. Package outline SOT38-4 (DIP16) REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA SOT38-4 95-01-14 03-02-13 MH c (e )1 ME A L seating plane w M e D Z E pin 1 index b 0 5 10 mm scale Note 1. Plastic or metal protrusions of 0.25 mm (0.01 inch) maximum per side are not included. UNIT A max. 12 b1 (1) (1) (1) b2 cD E e M ZHL mm DIMENSIONS (inch dimensions are derived from the original mm dimensions) A min. A max. b max.wMEe1 1.73 1.30 0.53 0.38 0.36 0.23 19.50 18.55 6.48 6.20 3.60 7.80 10.0 inches 0.068 0.051 0.021 0.015 0.014 0.009 1.25 0.85 0.049 0.033 0.77 0.73 0.26 0.24 0.14 0.31 0.39 DIP16: plastic dual in-line package; 16 leads (300 mil) SOT38-4
74HC_HCT4052_6 © NXP B.V. 2010. All rights reserved. Product data sheet Rev. 06 — 11 January 2010 23 of 27 NXP Semiconductors 74HC4052; 74HCT4052 Dual 4-channel analog multiplexer/demultiplexer Fig 24. Package outline SOT403-1 (TSSOP16) UNIT A 1 A2 A3 bp cD (1) E (2) (1)eH E LL p QZ ywv θ REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm 0.15 0.05 0.95 0.80 0.30 0.19 0.2 0.1 5.1 4.9 4.5 4.3 0.65 6.6 6.2 0.4 0.3 0.40 0.06 o o0.13 0.10.21 DIMENSIONS (mm are the original dimensions) Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included. 0.75 0.50 SOT403-1 MO-153 99-12-27 03-02-18 w M bp D Z e 0.25 16 9 θ AA1 Lp Q detail X L (A )3 HE E c v M A XA y 0 2.5 5 mm scale TSSOP16: plastic thin shrink small outline package; 16 leads; body width 4.4 mm SOT403-1 A max. 1.1 pin 1 index
74HC_HCT4052_6 © NXP B.V. 2010. All rights reserved. Product data sheet Rev. 06 — 11 January 2010 24 of 27 NXP Semiconductors 74HC4052; 74HCT4052 Dual 4-channel analog multiplexer/demultiplexer Fig 25. Package outline SOT763-1 (DHVQFN16) terminal 1 index area 0.51 A1 EhbUNIT ye 0.2 c REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm 3.6 3.4 Dh 2.15 1.85 2.6 2.4 1.15 0.85 2.50.30 0.18 0.05 0.00 0.05 0.1 DIMENSIONS (mm are the original dimensions) 0.5 0.3 L 0.1 v 0.05 w 0 2.5 5 mm scale SOT763-1 DHVQFN16: plastic dual in-line compatible thermal enhanced very thin quad flat package; no leads; 16 terminals; body 2.5 x 3.5 x 0.85 mm A(1) max. A c detail X yy1 Ce L Eh Dh e b 15 10 X D E C B A terminal 1 index area AC C Bv M w M E(1) Note 1. Plastic or metal protrusions of 0.075 mm maximum per side are not included. D(1) 02-10-17 03-01-27
74HC_HCT4052_6 © NXP B.V. 2010. All rights reserved. Table 13. Abbreviations Table 14. Revision history Modifications: • Added type number 74HCT4052PW (TSSOP16 / SOT403-1 package).
74HC_HCT4052_6 © NXP B.V. 2010. All rights reserved. Product data sheet Rev. 06 — 11 January 2010 26 of 27 NXP Semiconductors 74HC4052; 74HCT4052 Dual 4-channel analog multiplexer/demultiplexer 16. Legal information
16.1 Data sheet status
[1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com.
16.2 Definitions
Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail.
16.3 Disclaimers
General — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use — NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) may cause permanent damage to the device. Limiting values are stress ratings only and operation of the device at these or any other conditions above those given in the Characteristics sections of this document is not implied. Exposure to limiting values for extended periods may affect device reliability. Terms and conditions of sale — NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, including those pertaining to warranty, intellectual property rights infringement and limitation of liability, unless explicitly otherwise agreed to in writing by NXP Semiconductors. In case of any inconsistency or conflict between information in this document and such terms and conditions, the latter will prevail. No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from national authorities.
16.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 17. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification.
NXP Semiconductors 74HC4052; 74HCT4052 Dual 4-channel analog multiplexer/demultiplexer © NXP B.V. 2010. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 11 January 2010 Document identifier: 74HC_HCT4052_6 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. 18. Contents